Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s
manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to
use all the features of your new Jensen VM9511TS Mobile Multimedia AM/FM/DVD Receiver
for maximum enjoyment.
Gracias por elegir los productos Jensen. Esperamos que encuentre en este manual
instrucciones claras y fáciles de seguir. Si se toma unos pocos minutos para leerlo, aprenderá
cómo utilizar todas las funciones de su nuevo radio Jensen para su máximo entretenimiento.
Merci d'avoir choisi un produit Jensen . Nous espérons que vous allez trouver les instructions
dans ce guide de propriétaire claires et faciles à suivre . Prenez quelques minutes à le
consulter, vous apprendrez à utiliser toutes les fonctions de votre nouvelle radio Jensen pour
en tirer une jouissance maximum.
Garantie limitée de 12 mois .............................................................................................. 114
i
VM9511TS
PREPARATION
Congratulations on your purchase of the Jensen VM9511TS
Mobile Multimedia AM/FM/DVD Receiver.
It’s a good idea to read all of the instructions before beginning
the installation. We recommend having your Jensen
VM9511TS installed by a reputable installation shop.
Features
DVD
• Compatible formats: DVD-R, DVD-RW, DVD+R,
DVD+RW, CD-R, CD-RW, CD-DA, MP3, WMA, SVCD,
VCD, MPEG2, MPEG4, AVI and JPEG
• Region 1 playback
• 16:9 Aspect ratio- Wide / Normal / Cinema
• Front panel DVD control
• High-speed Fast Forward / Fast Rewind 2X, 4X, 8X, 32X
• Play, Pause, Stop, Slow
• Chapter Up / Down
• V-SEL - MultiZone output 'Kid-Zone'
• Wolfson Microelectronics high performance 24-bit, 192
kHz DAC supports 6-channel and 2-channel "Down-Mix”
audio modes
• Fully automatic motorized TFT LCD flip-out and up
• 16-step TFT LCD tilt adjustment
• Beep Tone confirmation
• 1.0 Din
• Import/ISO/DIN mountable
• Heat management system - Incorporates forced aircooling to keep the chip-sets operating at nominal
temperatures
• Heavy duty galvanized chassis
Multi-ZONE
• Allows front passengers to listen to the radio while rear
passengers listen to a CD, MP3, WMA or watch DVDs
General
• Full function infrared remote control
• Limited function infrared "Kid Zone" remote
• OSD - On Screen Display menu control
• High-performance audio processor
• Electronic volume, bass, treble, balance and fader
• Bass center frequency adjustment - 60, 80, 100, 130,
150 and 200Hz
• Bass Q factor - 1.0, 1.25, 1.5 and 2.0
• Treble center frequency adjustment - 10, 12.5, 15 and
17kHz
• Subwoofer crossover - 80, 120 and 160Hz
• Subwoofer Phase - 0 - 180 degrees
• Subwoofer level - variable
• 100-ohm low impedance pre-amp outputs, all channels
• 5V Peak / 2V RMS RCA outputs, all channels
• 1-pair front RCA outputs and 1-pair rear/surround RCA
outputs
• Single Subwoofer RCA output
• Center Channel RCA pre-amp output (variable)
• 1-pair headphone/Multi-ZONE RCA outputs
• 1-pair auxiliary RCA A/V inputs
• Back-up camera input with reverse override
• 1 NTSC composite video output for additional screens
• NTSC Multi-ZONE composite video for additional screens
• Front panel (when screen is closed) high contrast LCD
• Rotary encoder audio control
• Joystick menu navigation
Tools and Supplies
You will need these tools and supplies to install your
VM9511TS:
• Torx type, flat-head and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket
wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
WARNING! Only connect the unit to a12-volt power
supply with proper grounding.
WARNING! Never install this unit where operation and
viewing could interfere with safe driving conditions.
WARNING! To reduce the risk of a traffic accident
(except when using for rear-view video camera) never
use the video display function while driving the vehicle.
This is a violation of federal law.
WARNING! Never disassemble or adjust the unit without
the assistance of a professional. For details, please
consult your local car stereo specialty shop.
WARNING! To prevent injury from shock or fire, never
expose this unit to moisture or water.
1
WARNING! Never use irregular discs.
WARNING! To prevent damage to the mechanism inside
this unit, avoid impact to the TFT monitor.
WARNING! Do not change the fuse on the power wire
without professional guidance. Using an improper fuse
may cause damage to the unit and result in a fire.
WARNING! The monitor employs an automatic motorized
mechanism. To prevent damage to the core mechanism,
please do not push, pull or swivel the monitor manually.
Optional Accessories
iAUX3 READY (Sold Separately)
•Can connect to any portable media device or multimedia
device using a standard 3.5mm plug
•Converts 3.5mm auxiliary input to RCA stereo outputs
for easy connection to the radio’s AUX inputs
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and
remove the negative (-) battery cable prior to installation.
VM9511TS
NOTE: If the VM9511TS is to be installed in a vehicle
equipped with an on-board drive or navigation computer,
DO NOT disconnect the battery cable. If the cable is
disconnected, the computer memory may be lost. Under
these conditions, use extra caution during installation to
avoid causing a short circuit.
2
VM9511TS
WIRING DIAGRAM
3
WIRING DIAGRAM - MULTIMEDIA CONNECTIONS
VM9511TS
*TERK XMDJEN100 cables (sold
separately)
**TERK XMD1000 Direct Tuner and
antenna (sold separately)
***NAV100 (sold separately)
4
VM9511TS
INSTALLATION
Pre-installation
1.Press the metal levers on both sides to remove the halfsleeve from the radio.
2.Remove the transport screws.
PREPARE RADIO
CAUTION! Be careful not to damage the car wiring.
4.Place the radio in front of the dashboard opening so the
wiring can be brought through the mounting sleeve.
Wiring
Complete wiring as illustrated in the wiring diagram on page
3. Once the wiring is complete, reconnect the battery
negative terminal. If there is no ACC available, connect the
ACC lead to the power supply with a switch.
NOTE: When replacing a fuse, be sure to use correct
type and amperage to avoid damaging the radio. The
VM9511TS uses one 15 amp mini-ATM fuse, located in
the black filter box in-line with the main wire harness.
FINAL INSTALLATION
3.Install the half-sleeve.
a. Install adapter if necessary (optional).
b. Install half-sleeve into adapter or dashboard (use only
the supplied screws). Do not force the sleeve into the
opening or cause it to bend or bow.
c. Locate the series of bend-tabs along the top, bottom
and sides of the mounting sleeve. With the sleeve fully
inserted into the dashboard opening, bend as many of
the tabs outward as necessary so that the sleeve is
firmly secured to the dashboard.
d. Install support strap to make the unit more stable.
INSTALL HALF SLEEVE
3d
3c
3b
3a
Final Installation
After completing the wiring connections, turn the unit on to
confirm operation (ignition switch must be on). If unit does not
operate, recheck all wiring until problem is corrected. Once
proper operation is achieved, turn off the ignition switch and
proceed with final mounting of the chassis.
1.Connect wiring adapter to existing wiring harness.
2.Connect antenna lead.
3.Carefully slide the radio into the half-sleeve, making
sure it is right-side-up, until it is fully seated and the
spring clips lock it into place.
NOTE: For proper operation of the CD/DVD player, the
chassis must be mounted within 20° of horizontal. Make
sure the unit is mounted within this limitation.
4.Attach one end of the perforated support strap
(supplied) to the screw stud on the rear of the chassis
using the hex nut provided. Fasten the other end of the
perforated strap to a secure part of the dashboard either
above or below the radio using the screw and hex nut
provided. Bend the strap to position it as necessary.
CAUTION! The rear of the radio must be supported with
the strap to prevent damage to the dashboard from the
weight of the radio or improper operation due to
vibration.
5.Replace any items you removed from the dashboard.
Final ISO-DIN Installation
1.Remove trim ring.
2.Mount factory brackets on new radio using existing
screws from old radio.
3.Slide radio chassis into dash opening and secure.
4.Reinstall dash panel.
FINAL ISO-DIN INSTALLATION
Using the iAUX3 External AV Connector
The iAUX3 (sold separately) allows you to connect a variety
of external devices, including a VCR, DVD player, portable
MP3 player, etc., to your VM9511TS without removing the
radio.
To install the iAUX
back of the VM9511TS (see the Wiring Diagram on page 3),
and then install the iAUX
plugging in auxiliary devices.
3
, connect it to the AUX-IN cables on the
3
in a location convenient for
5
CONTROLS AND INDICATORS
Button Operation
1. OPEN
Press to activate the automatic mechanical system and move
the TFT monitor into viewing position. Press again to close
the TFT.
2. WIDE/ PICTURE
Press to adjust the display aspect of the picture to one of
three settings: Cinema, Full, Normal or OFF. Press and hold
to access picture settings.
3. ( )
Press to adjust the upward tilt angle of the screen one step at
a time. Press and hold this button to continuously adjust the
upward tilt or picture settings.
4. ( )
Press to adjust the downward tilt angle of the screen one step
at a time. Press and hold this button to continuously adjust
the downward tilt or picture settings.
5. DISP
Press to display system information on the screen.
6. VOL/LO/DX
Rotate to adjust the volume. Press and release to enter and/
or confirm audio settings. Press and hold to activate the Local
(LOC) setting.
7. POWER/MUTE
Press once to turn the unit on. Press again to mute the
volume. Press and hold to turn the unit off.
8. 1/AUDIO
DVD Mode: Press to select audio language during playback.
TUNER Mode: Press once to play preset radio station
channel 1. Press and hold to store the current radio station in
preset channel 1.
9. 2/SUBTITLE
DVD Mode: Press once to select the subtitle language during
playback.
TUNER Mode: Press once to play preset radio station
channel 2. Press and hold to store the current radio station in
preset channel 2.
VM9511TS
6
VM9511TS
CONTROLS AND INDICATORS
10. 3/SCN
DVD Mode: Press once to start scan playback.
TUNER Mode: Press once to play preset radio station
channel 3. Press and hold to store the current radio station in
preset channel 3.
11. 4/RPT
DVD Mode: Press once to start repeat playback.
TUNER Mode: Press once to play preset radio station
channel 4. Press and hold to store the current radio station in
preset channel 4.
12. 5/2-6CH/RDM
DVD Mode: Press once for random playback.
TUNER Mode: Press once to play preset radio station
channel 5. Press and hold to store the current radio station in
preset channel 5.
CD Mode: Press and hold to switch between 2 channel & 6
channel audio output.
13. 6/STOP
DVD Mode: Press once to stop playback.
TUNER Mode: Press once to play the preset radio station
channel 6. Press and hold to store the current radio station in
preset channel 6.
14. BAND
TUNER Mode: Press to switch between FM and AM.
15. SRC
Press once to select playing mode.
Press and hold to toggle rear zone mode On/0ff.
16. ( )
DVD Mode: Press once to play back the previous chapter/
track.
TUNER Mode: Press once to auto-search for the previous
available radio station.
MENU Mode: Press once to move the cursor to the left.
17. ( )
DVD Mode: Press once to enter the next chapter or track.
TUNER Mode: Press once to auto-search the next available
radio station.
MENU Mode: Press once to move the cursor to the right.
18. ()
DVD Mode: Press once for fast forward/fast reverse.
TUNER Mode: Press to go up one frequency step.
MENU Mode: Press once to move the cursor up.
19. ()
DVD Mode: Press once for slow forward/slow reverse.
TUNER Mode: Press to go down one frequency step.
MENU Mode: Press once to move the cursor down.
20. PLAY/ENTER
DVD Mode: Press once to start a playback.
Press once to confirm a selection.
21. ()
Press once for disc insertion/ejection.
Press and hold to reset core mechanism position.
22. RESET
Press to reset system settings to factory default (except the
password and parental lock setting).
23. LCD Display
24. TFT Display
25. IR Remote Control Receiver
26. AS (Auto Store)
Press to automatically store strong radio stations in the six
preset channels in the current band.
27. SD Card Slot
7
CONTROLS AND INDICATORS
LCD Display/Indicators
1. Disc Indicator
Illuminated when disc is loaded
2. DVD Playback Indicators (SCN/RPT/RDM/ALL)
The following DVD playback indicators become Illuminated
when the corresponding function is active:
• SCN: scan playback
• RPT: repeat playback
• RDM: random playback
• ALL: playback all chapters
3. Loudness Indicator (LOUD)
The loudness indicator becomes illuminated when the LOUD
function is activated.
4. Main Display
The main display is an 8 digit, 14 segment LCD which
displays the time, tuning frequency and other text
information.
5. Channel/Disc Display
The channel/disc display is a 2 digit, 7 segment LCD display
which displays the disc number or radio channel indicators
when the corresponding function is active:
• CH: radio is activated
• DISC: DVD mode is activated
6. Stereo/Local Indicator
The stereo/local indicator illuminates one of the following
indicators when the corresponding function is active:
• ST: radio is in stereo mode
• LOC: local radio station seeking function is activated
VM9511TS
123456
8
VM9511TS
FRONT ZONE REMOTE CONTROL
NOTE: Your remote control may differ slightly
from the one pictured here. The above diagram is
for illustrative purposes only.
9
VM9511TS
Table 1: Front Zone Remote Control Functions
ButtonFunction
NameRef#DVDVCDTUNERCD/MP3TVXMiPod
MENU1Enters the main menu of
TITLE2Enters the title menu of
MUTE3Toggles on/off audio out-
POWER/
AUDIO5Changes the audio lan-
REPT A-B6Setup to repeat playback
REPT7Repeats playback of cur-
SRC8Selects playing modeSelects playing modeSelects playing modeSelects playing modeSelects playing modeSelects playing modeSelects playing mode
4Turns the power on/offTurns the power on/offTurns the power on/offTurns the power on/offTurns the power on/offTurns the power on/offTurns the power on/off
guage for disc playback
from time frame A to time
frame B
rent chapter
subtitle
tion
11Continuously adjusts
front panel tilt angle
12Continuously adjusts
front panel tilt angle
ent angle for a scene
14Fast forwards the disc
content
17Selects the previous
chapter for playback
18Pauses playback/starts
playback
19Selects the next chapter
for playback
Turns on PBC when
playing VCD
Plays first ten seconds of
each chapter/title
Toggles on/off audio output
Setup to repeat playback
from time frame A to time
frame B
Repeats playback of current chapter
Displays playing information
Continuously adjusts
front panel tilt angle
Continuously adjusts
front panel tilt angle
Plays back Picture CD
with different angle of
picture displayed
Fast forwards the disc
content
Selects the previous
chapter for playback
Pauses playback/starts
playback
Selects the next chapter
for playback
Toggles on/off audio output
Displays playing information
Continuously adjusts
front panel tilt angle
Continuously adjusts
front panel tilt angle
Searches an available
radio station by decreasing tuning frequency
Scans FM/AM radio station; plays/stores radio
station; deletes radio station
Searches an available
radio station by increasing tuning frequency
Toggles on/off audio output
Repeats playback of current track
Display playing information
Continuously adjusts
front panel tilt angle
Continuously adjusts
front panel tilt angle
Fast forwards the disc
content
Selects the previous
track for playback
Pauses playback/starts
playback
Selects the next track for
playback
Toggles on/off audio output
Displays playing information
Continuously adjusts
angle of TFT screen
Continuously adjusts
angle of TFT screen
Searches an available TV
station by decreasing tuning frequency
Scans TV station; plays/
stores TV station; deletes
TV station
Searches an available TV
station by increasing tuning frequency
Displays XM Setup Menu Selects Photo mode
Selects Music mode
Toggles on/off audio output
Selects Category ModeRepeats playback of cur-
Displays playing information
Continuously adjusts
angle of TFT screen
Continuously adjusts
angle of TFT screen
Searches an available
radio station by decreasing tuning frequency
Scans XM radio station;
plays/stores radio station; deletes radio station
Searches an available
radio station by increasing tuning frequency