Jensen XRS Series, XRS 525, XRS 652, XRS 682, XRS 692 Owner's Manual

...
Page 1
Page 2
Page 3
INTRODUCTION
Thank you!
'We're all about the music'
Thank you for your purchase of these JENSEN mobile speakers. JENSEN has been delivering great sounds for more than 75 years, and is well known for its technology leadership in the acoustic arena. Always at the industry’s forefront, JENSEN speakers provide abundant features, extreme power handling, and tremendous versatility. The smooth, hip style is included.
Actually we invented the sound you still hear today. Take a listen to our scorching hot XRS Series speakers incorporating the latest speaker technology from JENSEN.
JENSEN's Sound Lab utilizes their latest innovation, (CSTT) Clear-Sound Tweeter Technology . CSTT is designed around Teteron, a revolutionary light weight textile dome material so light weight it's almost clear. It has very low moving mass for superior imaging, teeming smooth high frequency response, low distortion and excellent dynamic range. Super swivel-ability tweeter means super flexible installations for almost any application.
Our newly perfected Injection Molded Titanium-Lum Poly-Cone Woofer (IMTPW) delivers deep rich bass response and natural mid-range nuance reproduction, replicating true-to-life vocals & music.
Unlike foam surrounds, our ultra durable Nitrile rubber suspension system absorbs undesired cone resonance's to enhance the overall frequency response of the speaker. It also keeps the cone centered and endures more extreme environmental conditions than standard foam surrounds.
Ô
-
Voice coil leads are ingeniously interwoven into the spider assembly to virtually eliminate cone “lead slap”; this reduces low frequency distortion and increases reliability. XRS speakers utilize Kapton voice coil formers. These reduce the cone weight, enhance speaker efficiency, and dramatically improves power handling.
For installation assistance, the XRS speakers use nickel­plated quick release push terminals and low profile ABS grilles to reduce installation hassles.
CSTT Clear-Sound Tweeter Technology Teteron Dome Material, for Extended Frequency
Response
Coaxial Super Swivel Tweeter Base Design for
Installation Flexibility IMTPW- Injection Molded Titanium Poly-Cone Woofer Nitrile Rubber Surround - Endures Temperature
Extremes and Outlasts Ordinary foam Surrounds Kapton Voice Coil Formers Low Profile ABS Grilles Rubber Magnet Boot Cover Nickel Plated Quick Release Push Terminals Cold Rolled Stamped Steel Basket
Highlighted Features
!
!
!
!
!
!
!
!
!
!
Ô
1
Page 4
INTRODUCTION
Preparation
Required Tools
!
!
!
!
!
!
!
!
!
!
!
Disconnect battery cable from negative(-)battery
terminal.
Check all safety regulations in your vehicle's owner's
manual. To ensure an obstacle-free fit, check and double
check mounting depth of the speakers against
available depth, as well as the location of window
mechanics, door handles, and window handles. If using provided grilles, be sure mounting location is
sufficient distance from door and/or window handles.
The following is a list of tools needed for installation:
#2 Phillips screwdriver Battery post wrench Hand held drill w/assorted bits Wire strippers Wire crimpers Wire cutters 3mm allen wrench
Since some of these Jensen Full Range Speakers are most often used as direct replacements for stock speakers, some of the following instructions will not apply. For custom installations see your Authorized Jensen Dealer.
WARNING: Check vehicle's owner's manual
before disconnecting the battery. Disconnecting
the battery in some vehicles may require an anti-
theft code when reconnecting. Some vehicles
may run rough after reconnecting the battery and
require that the on-board computer be reset at
the dealership. Check with your local dealer if
you are uncertain.
Welcome to Jensen!
This manual is designed to provide information for the owner, salesperson and installer. For those of you who want quick information on how to install this product, please turn to the Installation Section of this manual. Other information can be located by using the Table of Contents. We at Jensen have worked very hard to make sure all the information in this manual is current. But, as we are constantly finding new ways to improve our product, this information is subject to change without notice.
Installation...................................................Page 3
Specifications..............................................Page 7
Warranty .....................................................Page 8
If, after reading your manual, you still have questions regarding this product, we recommend that you see your Jensen dealer. If you need further assistance, you can call us direct at 1-800-323-4815.
Be sure to have your model number and date of purchase available when you call. Please read your warranty clearly and retain your receipt for possible future use.
2
Page 5
Basic Installation Steps
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
: Remove existing speaker.
: Position new speaker and align with existing
mounting holes.
: Attach the positive (+) and negative (-) speaker
terminals (see FIGURE 2). Be sure to observe proper polarity when connecting the wires.
: If not using factory grilles, attach grille.
: Mount speaker (using factory hardware when
possible).
: Reconnect negative battery terminal.
INSTALLATION
FIGURE 2 - CONNECTING SPEAKER WIRES
(+) (-)
FIGURE 3 - REAR DECK INSTALLATION
FIGURE 1 - DOOR PANEL INSTALLATION
Grille
Door Panel Speaker
Push terminal UP to insert speaker wire.
3
Page 6
Installing with Adapter Ring
The XRS525 and XRS652 come with an adapter ring to fit a variety of different openings. To use the adapter ring, secure the adapter ring to the vehicle using sheet metal screws, then attach the speaker to the ring with the machine screws provided.
INSTALLATION
FIGURE 4 - ADAPTER RING INSTALLATION
Door Panel Speaker
Adapter Ring
Grille
NOTE
If using both the adapter ring and the supplied grilles (not factory), you will have to provide additional M4 screws of the appropriate length for your application.
Rear Deck
4
Page 7
Using the Conversion Ring with the XRS802
The conversion ring should be installed when an existing 6x9 hole is to be used for installation. If cutting a new installation hole, the diameter should be 7 1/8” round, making the conversion ring unnecessary.
FIGURE 6 - CONVERSION RING FRONT INSTALL
INSTALLATION
FIGURE 7 - CONVERSION RING TOP INSTALL
FIGURE 5 - CONVERSION RING BOTTOM INSTALL
Rear Deck
Rear Deck
Conversion
Ring
Door Panel
XRS802 Speaker
5
Page 8
Adjusting the Swivel Tweeter
To get the best stereo imaging and most true-to-life sound reproduction, the swivel tweeters should be angled toward the listener's ears. To tilt the tweeter, push the edge of the chrome tweeter bezel to rotate the tweeter to the desired listening position. The bezel may need to be rotated before swiveling to achieve the desired angle.
slightly
FIGURE 8 - ADJUSTING THE SWIVEL TWEETER
INSTALLATION
Push edge of swivel tweeter to angle it toward the listener's ear.
NOTE
Avoid using excessive force while swiveling the tweeter, as permanent damage can occur.
6
Page 9
XRS 525 XRS652 XRS682 XRS692 XRS802
Configuration
Midrange Diameter
Super Tweeter Diameter
Frequency Response
Crossover
Power Handling
Sensitivity
Grilles Included
Mounting Hardware
Adapter Ring
Mounting Depth
Magnet Weight
2-Way Full-Range 2-Way Full-Range 2-Way Full-Range 2-Way Full-Range 2-Way Full-Range
5.25" 6.5" 6" x 8" 6" x 9" 8"
19mm Swivel Tweeter 19mm Swivel Tweeter 19mm Swivel Tweeter 25mm Swivel Tweeter 25mm Swivel Tweeter
60Hz - 40kHz 40Hz - 40kHz 40Hz - 40kHz 37Hz - 40kHz 35Hz - 40kHz
6dB/Octave LPF; 6dB/Octave LPF; 6dB/Octave LPF; 6dB/Octave LPF; 6dB/Octave LPF; 6dB/Octave HPF 6dB/Octave HPF 6dB/Octave HPF 6dB/Octave HPF 6dB/Octave HPF
35 Watts RMS 50 Watts RMS 50 Watts RMS 60 Watts RMS 70 Watts RMS
175 Watts Peak 250 Watts Peak 250 Watts Peak 300 Watts Peak 350 Watts Peak
90dB @ 1 watt/1 meter 91dB @ 1 watt/1 meter 88dB @ 1 watt/1 meter 92dB @ 1 watt/1 meter 91dB @ 1 watt/1 meter
Yes Yes No Yes Yes
Yes Yes Yes Yes Yes
Yes Yes No No Yes
2 1/2" (64mm) 2 11/16" (68mm) 2 11/16" (68mm) 3 1/2" (90mm) 3 5/8" (92mm)
9oz. 13oz. 11oz. 27oz. 27oz.
SPECIFICATIONS
7
Page 10
WARRANTY
Limited 1 Year Warranty - USA and Canada
Length of Warranty.
Persons Protected.
What is Covered
How You Can Get Service. U.S. Purchasers.
Canadian Purchasers.
What We Will Pay For.
This warranty from Audiovox Electronics Corporation shall be in effect for a period of 1 year from the date of the first consumer purchase.
This warranty will be enforceable by the original owner during the warranty period so long as proof of date of purchase from an authorized dealer is presented whenever warranty service is required.
. Except as otherwise specified below, this warranty covers all defects in material and workmanship in this product. The following are not covered: damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product; damage occurring during shipment (claims must be presented to the carrier); any plexiglass included with the product; elimination of car static or other electrical interferences; any product purchased outside USA or Canada, or on which the serial number has been defaced, modified or removed.
Please telephone Jensen Customer
Service at 1-800-323-4815.
The product should be returned to the dealer from whom it was purchased and such dealer either will service or arrange for service of the product. If shipment of the product is required, it should be packed properly. The original dated bill of sale must always be included with the product as proof of warranty coverage.
We will pay for all labor and material expenses required to repair the product, but you must pay any labor costs for the removal and/or installation of the product. If the product is shipped for warranty service, you must prepay the initial shipping
charges, but Audiovox Electronics Corporation will pay the return shipping charges if the product is returned to an address inside the USA or Canada.
Audiovox Corp's liability is limited to the repair or replacement, at our option, of any defective product and shall not include special, indirect, incidental or consequential damages of any kind. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY IN CONTRACT OR TORT, WHETHER OR NOT ARISING FROM THE COMPANY'S NEGLIGENCE, ACTUAL OR IMPUTED. NO PERSON OR REPRESENTATIVE IS AUTHORIZED TO ASSUME FOR THE COMPANY ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT. IN NO EVENT SHALL COMPANY BE LIABLE FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Limitation of Implied or Statutory Warranties and Conditions. Exclusions.
8
Loading...