Jensen MP6512i User Manual
i
MP6512i
TABLE OF CONTENTS
Introduction ..............................................................................................1
Installation ................................................................................................2
Wiring .......................................................................................................5
Front Panel Release ................................................................................6
Operation .................................................................................................7
Tuner Operation .....................................................................................10
CD Player Operation ..............................................................................12
MP3/WMA Operation .............................................................................13
Satellite Radio Operation .......................................................................17
iPod Operation .......................................................................................19
Remote Control ......................................................................................20
Care and Maintenance ...........................................................................21
Troubleshooting .....................................................................................22
Specifications .........................................................................................23
ii
MP6512i
MP6512i
1
INTRODUCTION
Congratulations on your purchase of the Jensen MP6512i Mobile Receiver.
It’s a good idea to read all of the instructions before beginning the
installation. We recommend having your Jensen MP6512i installed by a
reputable installation shop.
Features
CD / MP3 / WMA
• ID3 Tag Compatible
• Last Position Memory
• Directory Search (MP3 / WMA Only)
• MP3/WMA search by Track, File and Character
• Audible Forward / Reverse Track Search
• Random, Repeat and Intro
• Play, Pause, Stop, Next Track and Previous Track
• ESP Buffer (Electronic Shock Protection)
AM-FM
• RDS-Radio Data System
• USA / Europe Frequency Spacing
• 30 Station Presets (18 FM / 12 AM)
• Auto Stereo / Mono
• Local / Distance
• Auto Store / Preview Scan
Sat Radio Ready
• Compatible with XM and Sirius Tuners (Sold Separately)
• Requires XMDJEN100 and JXMC Cables (Sold Separately)
• Satellite Channel Name, Category, Artist, or Song Title can be
displayed
iPod
• JLinkDirect - High Speed Direct Connect Interface To Access iPod
Playlists, Artists, Albums, Songs.
• Intuitive Interface for Easy iPod Navigation
• Power Management Charges iPod While Connected
• Requires jLinkCable (Sold Separately)
MediaLink
2
• Under Dash Interface Allows Portable Media Devices to be Connected
• MediaLink2 Includes the Following connectivity:
• jLinkDirect 8-pin DIN for iPod
• USB - Supports Hard Drives and Flash Memory Drives
• SD Card - Playback of MP3 and WMA files
• 3.5mm Audio Only Input
Chassis
• Detachable Faceplate
• 1.0 DIN (Import / ISO-DIN Mountable)
• 8 Character / Segment Type LCD Display
General
• Infrared Remote Control
• Programmable Volume Control
• MediaPlex AudioCore offers Adjustable Bass, Midrange and Treble
Center Frequencies as well as Bass and Midrange Q Adjustments
• Five Preset EQ Curves
• Loudness
• Rotary Encoder Audio Control
• Beep Tone Confirmation (On-OFF Option)
• Variable Subwoofer Line Output w/ Multiple X-over Frequency Settings
• Front and Rear Line Output
• 200-Ohm Preamp Line Outputs
• 2VRMS Line Outputs
Optional Accessories
• jLinkCable - iPod interface Cable
MP6512i
3
CAUTION: For proper operation of the CD player, the chassis must be
mounted within 20° of horizontal. Make sure the unit is mounted within
this limitation.
4. Place the radio in front of the dashboard opening so the wiring can be
brought through the mounting sleeve. Follow the wiring diagram
carefully and make certain all connections are secure and insulated
with wire nuts or electrical tape. See “Wiring” on page 5. After
completing the wiring connections, turn the unit on to confirm operation
(vehicle ignition must be on). If the unit does not operate, re-check all
wiring until the problem is corrected.
5. Make sure the radio is right-side up, then
carefully slide the radio into the mounting
sleeve until it is fully seated and the spring clips
lock it into place.
6. Secure the rear of the unit to the car body
using the mounting bolt and rubber cushion.
7. Test the radio using the Operating Instructions
that follow.
Kit Installation
If your vehicle requires the use of an installation kit to mount this radio,
follow the instructions included with the installation kit to attach the radio to
the mounting plate supplied with the kit.
1. Wire and test the radio as outlined in the Mounting Sleeve Installation
instructions.
2. Install the radio/mounting plate assembly to the sub-dashboard
according to the instructions in the installation kit.
3. Attach the support strap to the radio and dashboard as described in the
Universal Installation instructions.
4. Replace the dashboard trim panel.
ISO Installation
This unit has threaded holes in the chassis
side panels which may be used with the
original factory mounting brackets of some
vehicles to mount the radio to the
dashboard. Please consult with your local
car stereo shop for assistance on this type
of installation.
1. Remove the existing factory radio
from the dashboard or center console
mounting. Save all hardware and
brackets as they will be used to mount the new radio.
2. Carefully unsnap the plastic frame from the front of the new radio
chassis. Remove and discard the frame.
3. Remove the factory mounting brackets and hardware from the existing
radio and attach them to the new radio. Do not exceed M5 x 9 MM
maximum screw size. Longer screws may damage components inside
the chassis.
4. Wire the new radio to the vehicle as outlined in the Universal Installation
instructions.
5. Mount the new radio assembly to the dashboard or center console
using the reverse procedure of step 1.
Fuses
When replacing a fuse, make sure the new fuse is the correct type and
amperage. Using an incorrect fuse could damage the radio.
Reconnect Battery
When wiring is complete, reconnect the battery negative terminal.
SPRING CLIP
MOUNTING
RUBBER
MOUNTING BOLT
RADIO
TRIM RING
BEND TABS
SLEEVE
CUSHION
MP6512i
4
Removing the Radio
To remove the radio after installation,
remove the trim ring by lifting in the
center and pulling it off from either
side. Insert the removal keys straight
back until they lock, then pull the
radio out. If removal keys are inserted
at an angle, they will not lock properly
and will not release the unit.
Technical Assistance
If you require assistance, contact Technical Support at 1-800-323-4815
from 9:00am to 6:00pm EST Monday through Friday.
Loading...