Jensen JiTS-260i User Manual
DOCKING TOWER SPEAKER FOR iPod AND iPhone
USER MANUAL
JiTS-260i
(iPhone/iPod Not Included)
PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING
THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
Selecting fine audio equipment such as the unit you've just purchased is only the start of your
musical enjoyment. Now it's time to consider how you can maximize the fun and excitement
your equipment offers. This manufacturer and the Electronic Industries Association's Consumer
Electronics Group want you to get the most out of your equipment by playing it at a safe level.
One that lets the sound come through loud and clear without annoying blaring or distortion and,
most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of
sound. So what sounds "normal" can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all,
we want you listening for a lifetime.
We Want You Listening For a Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer
and the Electronic Industries Association's Consumer Electronics Group recommend you
avoid prolonged exposure to excessive noise.
Customer's Record:
The serial number of this product is found on its back cover. You should note the serial number
of this unit in the space provided as a permanent record of your purchase to aid in identification
in the event of theft of loss.
DEAR JENSEN® CUSTOMER
Model Number: JiTS-260i Serial Number:
WARNINGS
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION:
Use of controls or adjustments or performance of procedures other than those specified may
result in hazardous radiation exposure.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these Instructions.
2) Keep these Instructions.
3) Heed all Warnings.
4) Follow all Instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturers
instructions. Minimum distances 2 cm around the apparatus for sufficient ventilation. The
ventilation should not be impeded by covering the ventilation openings with items, such as
newspapers, tablecloths, curtains, etc.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) No naked flame sources, such as lighted candles, should be placed on the apparatus.
10)Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. When
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
11) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
12)Only use attachments/accessories specified by the manufacturer.
13)Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
1
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICING TO QUALIFIED SERVICE PERSONNEL.
14)Unplug this apparatus during lightning storms or when unused for long periods of time.
15)Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
16)The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on apparatus.
17)Main plug is used as disconnect device and it should remain readily operable during
intended use. In order to disconnect the apparatus from the mains completely, the mains
plug should be disconnected form the mains socket outlet completely.
18)Caution mark and name plate are located at the back of apparatus.
19)Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
20)CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type.
IMPORTANT NOTES
Avoid installing the unit in locations described below:
•Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters.
•Places subject to constant vibration.
•Dusty, humid or moist places.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT. FULLY
INSERT THE PLUG TO MAIN POWER SOCKET.
SAVE THESE INSTRUCTIONS
2
COMPLIANCE WITH FCC REGULATIONS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Protect Your Furniture
This product is equipped with non-skid rubber 'feet' to prevent the product from moving when
you operate the controls. These 'feet' are made from non-migrating rubber material specially
formulated to avoid leaving any marks or stains on your furniture. However certain types of oil
based furniture polishes, wood preservatives, or cleaning sprays may cause the rubber 'feet' to
soften, and leave marks or a rubber residue on the furniture. To prevent any damage to your
furniture we strongly recommend that you purchase small self-adhesive felt pads, available at
hardware stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
3
INSTALLATION
1.MAIN BODY
2.BASE
3.WASHER
4.SCREW
5.SPEAKER COVER
6.TWEETER
7.REMOTE SENSOR
8.LOUD SPEAKER
9.SUBWOOFER
1.) Attach the wooden base to the main tower using the supplied 4 screws and washers as
shown in the above diagram.
2). Tighten all screws securely and then place the tower speaker on a flat floor.
3.) The speaker cover can be removed for cleaning.
4
FUNCTI ON STANDBY - VOLUME +
AUX IN 2
AUX IN 1
AC 120V~ 60Hz
AUX I N 1
1
2
3
MAIN UNIT
LOCATION OF CONTROLS
1.VIDEO OUT Jack
2.AUX 1 Input L/R RCA Connectors
3.Main POWER ON/OFF Switch
4.AUX 2 Input Jack
5.FUNCTION Button
6.POWER ON/STANDBY Button
7.VOLUME Down (-) Button
8.VOLUME Up (+) Button
9.Docking Bay Cover
10.iPod/iPhone Docking Bay
11.iPod/iPhone Docking connector
4 5 6 7 8
9
10
11
5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
REMOTE CONTROL
1.POWER ON/STANDBY Button
2.MUTE Button
3.iPod Menu Up/Down / Button
4.Skip Backward Button
5.Skip Forward Button
6.VOLUME +/- Buttons
7.FUNCTION Button
8.iPod MENU Button
9.Play/Pause Button
10.iPod ENTER Button
11.REPEAT Button
12.BASS +/- Buttons
13.iPod Function Button
14.SHUFFLE Button
15.Infrared Transmitter
16.Battery Compartment
15
16
CONNECTING THE AC POWER CORD
After attaching the wooden base to the tower speaker, fully unwind the AC power cord and
plug it into any convenient household 120V~ 60Hz AC outlet.
NOTE:
This unit is only designed to operate on normal 120V~ 60Hz AC power. Connecting this unit
to any other power source could result in damage that will not be covered by your warranty.
Please note that this unit is equipped with a polarized AC power plug where one blade is
wider than the other. This is a safety feature.
If this plug does not fit into your existing AC outlet, do not try to defeat this safety feature
by removing the wide blade to make it fit into your outlet. If this plug will not fit into your
outlet, you probably have an outdated non-polarized AC outlet and you should have your
outlet changed by a qualified licensed electrician.
GETTING STARTED
6
REMOTE CONTROL BATTERY INSTALLATION
The remote control operates on one CR2025 battery (included). To activate the remote
control, remove the insulation tab inserted in the battery compartment. To remove the tab,
pull it in the direction of the arrow in the illustration as shown.
When the operation of the remote control becomes intermittent
or unsatisfactory, replace the original battery with a new 3-volt
lithium battery.
Replacing the battery in the remote control:
1.) Press in on the side of the battery holder and pull the
holder out of the remote.
2.) Removed the exhausted battery and then install 1 new “CR2025” lithium
battery according to the polarity diagram on the battery compartment.
3.) Insert the battery holder into the remote control and make sure it locks
into place.
NOTE: Only use a well-known brand of battery to ensure the longest life and best
performance.
Battery Precautions
Replacement of batteries must be done by an adult.
The supply terminals are not to be short-circuited.
Non-rechargeable batteries are not to be recharged.
Exhausted batteries are to be removed.
Only batteries of the equivalent type are to be used.
Batteries are to be inserted with the correct polarity.
Dispose of batteries properly. Do not dispose of batteries in fire. The batteries may
explode or leak.
Notes:
The remote may not operate properly if there is an obstacle
between the unit and the remote transmitter.
The remote may operate intermittently if operated in direct
sunlight, under bright incandescent lamps, fluorescent lamps
or any other strong light source.
7
LISTENING TO YOUR iPhone/iPod
PLAYBACK
1.Push down on the back of the docking bay cover to open it and expose the docking bay.
2.Use the iPod adaptor included with your iPod (if needed) and insert it into the docking area.
No adaptor is required if you use an iPhone. Your iPod/iPhone can now be inserted into the
docking bay by placing the connector on the bottom of the iPhone/iPod onto the connector
in the docking bay.
Note: Please be careful when seating the iPhone/iPod into the docking bay to avoid damaging
the 30-pin connector on the iPhone/iPod or in the docking system.
3.Turn on the POWER ON/OFF switch on the back of the unit, and the standby indicator lights.
4.Press the STANDBY button to turn on the unit. The standby indicator goes off and the
function indicator lights.
5.Press the FUNCTION button or iPod button on the remote control to select iPod/Music
mode (the Red indicator lights on the FUNCTION button) and then press the
PLAY/PAUSE button to start playback.
6.Press the PLAY/PAUSE button on the remote control to pause or resume playback.
7.Press the VOLUME Up (+) / Down (-) button to adjust your desired volume level
8.Press the BASS + / - button on the remote control to adjust the desired bass level.
9.Press the or button on the remote control to select the desire music track.
Press and hold the or button for fast-rewinding or fast-forwarding during playback.
10.To remove the iPhone/iPod from the unit, press and hold the PLAY/PAUSE button on
the remote control for five seconds to switch off the device and then gently remove it from
the docking connector.
11. Press the STANDBY button to place the unit into standby mode. You can also
completely turn off the power to the unit by switching the Main POWER ON/OFF switch
on the back of the unit to the OFF position.
12. Close the dust cover after use.
iPod/iPhone playback function (Using Remote Control):
Press the MENU button, SELECT button and / buttons on the remote control to control
the iPod menu, scroll menu up/down and enter selection.
Note: 1.The iPod Menu Control function will work with most iPod touch/iPhone models in
iPod mode. Please make sure your iPod/iPhone is in iPod/Music mode. The function will
NOT work if the iPod/iPhone is on the MAIN or LOCKED screen.
2.The iPod menu navigating function of remote control will work on most iPhone or iPod
models except for the iPod nano 6th gen.
Press the REPEAT button repeatedly to cycle through the repeat options (repeat 1,
repeat all and repeat off) of your iPhone/iPod.
Press the SHUFFLE button to enable or disable the shuffle play function of your
iPhone/iPod.
Charging
Your iPhone/iPod will charge in all function modes when docked,
NOTE: To prevent damaging the dock connector, never twist the iPhone/iPod when
inserting or removing it.
8
Loading...