Page 1
Check for damage: We know you will be eager to install your new Speakers, however, please firstly inspect
your units for any damage. If you find a problem please contact us immediately at info@bdimports.com.au
Elite-101
Elite-202
Elite-303
Break in Period:
Premium grade parts and materials are used in these Elite-101/202/303 products so maximum performance can be obtained in
damp and dusty environments such as wall and ceiling cavity. Break In period is appx 10-20 playing hours after which time Bass
will improve. There is no need to limit playback volume at all during this time.
Wall cut tool
Supplied
Template
Not supplied
Philips screw driver
Stud Finder
Wall Cavity
Depth required:
Elite-101 85mm
Elite-202 62mm
Elite-303 75mm
Elite-606
See separate manual
Glass
The Ultimate In-Wall / In-Ceiling Speakers
Step 1: Advanced Planning
Decide the placement for your speakers. Advance planning in regards to the placement of your
speakers is critical. It is imperative that the wall or ceiling cavity be free from debris, moisture,
insulation, and any materials that are easily combustible. The mounting location must also be void of wall studs
or bracing in the location for the cutout. Adequate Wall Cavity depth (see above) to allow speakers to fit flush to
the wall or ceiling surface is important. If you are unsure of the contents of the wall in which you wish to mount
the speakers, Electronic Stud Finders work very well (see FIG 1), otherwise a professional installer can assist here.
Stud Finder
FIG 1.
Congratulations for buying the best In-Wall Speakers on the planet !
Please read this manual carefully understanding that advanced planning is essential.
Page 2
FIG 2.
Step 4: Cutting the Wall / Ceiling
Using the appropriate wall-cutting tool, blade or Stanley knife, accurately cut the hole in the wall material,
based on the correct cut-out dimension (see FIG 3).
Step 5: Installing Speaker Leads
For Elite-101 and 202, from your Receiver run one speaker cable thru the wall/ceiling to each Left and Right speaker (see FIG 4). For
Elite-303, run TWO speaker cables thru the wall/ceiling to each Elite-303 as this model has inbuilt Centre/Left and Centre/Right
speakers as well as Left and Right. (See FIG 5 and FIG 7). In both cases, leave enough slack in wire so that it can hang out of hole.
Step 3: Template:
Use the supplied template and mark the cut-out on the wall or ceiling. To mark, simply trace with a pencil,
along perforated line (see FIG 2). Ensure your markings are level.
Step 2: Fitting Glass Grills
Fit Elite-101 grills squarely and be certain ALL 4 magnets grab and not just 2 or 3. For Elite-202/303, align all 8 pins then gently press
Glass panel into rubber bushes. When removing, pull a little from top, then from bottom to remove evenly.
Step 7: Mounting Speakers Insert the entire speaker into the hole. Move Speaker wire away
from back of cone to avoid a possible rattle. Using a Phillips head screwdriver, tighten the screws attached to
the dog clamps until you feel Dog Clamps take grip (9~10 FULL TURNS). At this point you can see the gap
between Speaker Frame and wall/ceiling close fully. Then, NIP THESE UP - DO NOT OVERTIGHTEN. See FIG 6.
Note: If you are unable to install these speakers yourself, please contact an authorized electrician or
installation contractor.
Matching Subwoofer : Elite-606:
140 Watts RMS, Heavy-Duty “monster” driver with 40oz magnet and 2”Voice Coil is perfectly matched
to ALL JENSEN Speakers. Available in stunning Hi-Gloss White or Black. See separate Info Manual.
Step 6: Red-to-Red & Black to Black
Connect the speaker wire from the positive (RED+) terminal on the receiver to the positive (RED+) terminal on the speaker. Connect
the negative (BLACK-) the same way to the negatives. Note: If you inadvertently reverse one of the connections (i.e. RED to BLACK)
you will notice a severe lack of Bass from your system. This is called wiring your system “Out of Phase”. If this occurs, check the wiring
and reconnect as necessary.
Sound Settings
Boost switch. Adjust Elite-202 / 303 Treble switches to suit your sound preference.
If using a Subwoofer set to (+) to fully maximize performance. Note: Elite-101 has no switches but is
factory preset to Max Boost (+).
Eyeball Tweeters. You can adjust the angle of the Tweeter slightly in order to compensate for poor
mounting locations. Do this by adjusting Tweeter casing. DO NOT touch the Tweeter in any way as
permanent damage may occur.
FIG 3.
Elite-101, 202 & 303
Once final mounting positions are
determined, use pencil and
template (supplied) to mark the
wall and cut-out.
Template
Boost switches.
Eyeball Tweeters
Elite
606
Elite-101
Elite-202
Elite-303
JENSEN
Page 3
FIG 6.
9~10
full turns
TIPS: 9~10 Full Turns.
With a screw cutting a new
plastic thread, the first few
turns may appear stiff. It will
become easier. The trick is to
gently close the gap between
Speaker panel and wall, then
NIP THESE SCREWS UP – DO
NOT OVERTIGHTEN AND
DO NOT USE A BATTERY DRILL.
TIPS:
1. Use Laser level or Spirit level to ensure template is perfectly level.
2. Use a Stud Finder to Pre-plan your locations.
3. Both ends of Speaker Leads must be Pos (+) to Pos (+) & Neg (-) to Neg (-)
4. Do not use Battery Drill.
FIG 5.
To amp Centre
To amp L/R
FIG 4.
Elite-101 & 202
Run 1 Speaker lead to each
Left & Right Speaker.
Elite -303
Run 2 Speaker leads
to each
Left & Right Speaker.
(see FIG 7)
Elite-202
Page 4
Elite-101
Elite-202
Elite-303
Elite-606
Shape
Square
Rectangular
Rectangular
Gloss Black / White
Suited for
Wall
Wall
Wall
Floor Subwoofer
Description
Glass front
6.5”2 Way
Glass front
Twin 4.5”2 Way
Glass front Twin 4.5”
2 Way + inbuilt Twin
4.5” 2 Way Centre
Speaker
Hi Gloss enclosure with
Down-firing 8"
“Monster” driver with
40oz magnet & 2”V/coil
Tweeter size mm / inches
28mm
Pure Silk Dome
28mm
Pure Silk Dome
Twin 28mm
Pure Silk Domes
n/a
Power Handling
110 W RMS
140 W RMS
140 WRMS + 140WRMS
140 Watt RMS Output
Nom. Impedance
6 Ohms
6 Ohms
6 Ohms
n/a
Sensitivity
91db
90db
90db
n/a
Frequency Resp.
42Hz-21kHz
40Hz-21kHz
40Hz-21kHz
35Hz-200Hz
Min. Mounting Depth mm
85mm
62mm
75mm
n/a
Tweeter Boost switch
NO
YES
YES
n/a
Eyeball tweeter
YES
YES
YES
n/a
Paintable Faces & Grills
NO
NO
NO
n/a
Tweeter Protection
YES
YES
YES
n/a
Magnetic Shielding
NO
NO
NO
NO
Colours
Black / White
Black / White
Black / White
Hi Gloss Black or White
Outer Dimensions: mm
240 x 240
570 x 163
650 x 163
460(H)x 277(W)x 313(D)
Cut-out Dimensions: mm
226 x 226
325.5 x 137.5
568.5 x 137.5
n/a
Warranty
5 Years
unconditional
5 Years
unconditional
5 Years
unconditional
5 Years (1 year on
amplifier module)
Front Channels. From Receiver, run 2 Speaker Leads (one for L/R and other for Centre) to each LEFT and
RIGHT Speaker (FIG 7). At receiver end, take the two Centre Speaker Leads and TWIST both positives together
and connect to positive Centre terminal on Receiver. Ditto with Negatives to negative terminal. It is imperative
to keep all positives together and all negatives together.
Placement: Only rule is LEFT and RIGHT Speakers to be same distance from TV screen. We suggest each to
be 200mm ~ 350mm from Screen.
Elite-303 wiring diagram
Web: www.jensenspeakers.com.au Email: info@bdimports.com.au Sales: (03) 9846 3996
BD Imports Pty Ltd. PO Box 780 Templestowe, VIC. 3106
FIG 7.
Screen
Centre
Centre/L
12 Ohms
mono
Left
6 Ohms
Centre/R
12 Ohms
mono
Right
6 Ohms
Left
Centre
Right
Speaker
Leads 1 & 2
Speaker
Leads 3 & 4
+
+
+
_
_
_
Receiver / Amplifier
Front Channels
Page 5
Page 6
Loading...