Jenn-Air JMW9527DAW29, JMW9527DAS30, JMW9527DAB29, JMW8527DAW27, JMW8527DAS28 Owner’s Manual

...

g E N N - A i R 27" ELECTRIC WALL OVEN

JENN-AIR

Form No. A/01/08 Part No. w10169641

TABLE OF CONTENTS

Safety ...................................................................................1-3

Oven Cooking ................................................................4-12

Options ..........................................................................13-17

Favorites ........................................................................18-19

Setup ..............................................................................20-22

Help ........................................................................................23

Care & Cleaning .........................................................24-26

Maintenance .......................................................................27

Troubleshooting .........................................................28-29

Warranty & Service ...........................................................31

Guide de I'utilisateur ........................................................32

Guia del Usuario ...............................................................64

Litho U.S.A.

SAFETY

Read and follow all instructions before using this appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance only for its intended purpose as described in this guide.

To ensure proper and safe operation: Appliance

must be properly installed and grounded by a qualified

technician. Do not attempt to adjust, repair, service, or

replace any part of your appliance unless it is specifi- cally recommended in this guide. All other servicing

should be referred to a qualified servicer. Always disconnect power to appliance before servicing.

To Prevent Fire or Smoke

Damage

= Be sure all packing materials are removed from the

appliance before operating it.

• Keep area around appliance clear and free from combustible materials. Flammable materials should not

be stored in an oven.

IMPORTANT SAFETY INSTRUCTIONS

Warning and Important Safety Instructions appearing in this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution, and care must be exercised when installing, maintain- ing, or operating the appliance.

Always contact your dealer, distributor, service agent, or

manufacturer about problems or conditions you do not understand.

Recognize Safety Symbols, Words, Labels

• Many plastics are vulnerable to heat. Keep plastics away from parts of the appliance that may become

warm or hot.

• To prevent grease fires, do not let cooking grease or other flammable materials accumulate in or near the

appliance.

in Case of Fire

=Use dry chemical or foam-type extinguisher or baking

soda to smother fire or flame. Never use water on a grease fire.

1.Turn off appliance to avoid spreading the flame.

2. NEVER pick up or move a flaming pan.

3. Smother fire or flame by closing the oven door.

Child Safety

* NEVER leave children alone or unsupervised near the

appliance when it is in use or is still hot. Children should never be allowed to sit or stand on any part of

the appliance as they could be injured or burned.

:SAFETY

* Children must be taught that the appliance and

utensils in it can be hot. Let hot utensils cool in a safe place, out of reach of small children. Children should

be taught that an appliance is not a toy. Children should not be allowed to play with controls or other parts of the appliance.

About Your Appliance

• To prevent potential hazard to the user and damage to the appliance, do not use appliance as a space heater

to heat or warm a room. Also, do not use the oven as a storage area for food or cooking utensils.

• Do not obstruct the flow of air by blocking the oven vent.

* DO NOT TOUCH HEATING ELEMENTS OR INTERIOR

SURFACES OF OVEN. Heating elements may be hot even though they are dark in color. Interior surfaces of any oven become hot enough to cause burns. During and after use, do not touch, or let clothing or other flammable materials contact heating elements or interior surfaces of oven until they have had sufficient time to cool. Other surfaces of the appliance may become hot enough to cause burns - among these surfaces are: oven vent openings and surfaces near these openings, oven doors, windows of oven doors.

Do not touch a hot oven light bulb with a damp cloth

as the bulb could break. Should the bulb break, disconnect power to the appliance before removing

bulb to avoid electrical shock.

* A cooling fan should be heard whenever the oven is

operating. If you do not hear the fan, call an authorized servicer.

* NEVER use aluminum foil to cover an oven rack or

oven bottom. Misuse could result in risk of electric shock, fire, or damage to the appliance. Use foil only

as directed in this guide.

Cooking Safety

* Never heat an unopened food container in the oven.

Pressure build-up may cause container to burst resulting in serious personal injury or damage to the appliance.

• Use dry, sturdy potholders. Damp potholders may cause burns from steam. Dish towels or other substi-

tutes should never be used as potholders because they can trail across hot elements and ignite or get caught on appliance parts.

• Wear proper apparel. Loose fitting or long hanging- sleeved apparel should not be worn while cooking. Clothing may ignite and cause burns if garment comes in contact with heating elements.

* Always place oven racks in the desired positions while

oven is cool. Slide oven rack out to add or remove food, using dry, sturdy potholders. Always avoid

reaching into the oven to add or remove food. If a rack must be moved while hot, use a dry potholder. Do not let potholder contact hot element in oven.

• Use racks only in the oven in which they were shipped/purchased.

• Use care when opening the oven door. Let hot air or steam escape before removing or replacing food.

* PREPARED FOOD WARNING: Follow food

manufacturer's instructions. If a plastic frozen food container and/or its cover distorts, warps, or is other- wise damaged during cooking, immediately discard

the food and its container. The food could be contami- nated.

• Do not allow aluminum foil or meat probe to contact heating element.

• Always turn off all controls when cooking is com- pleted.

Utensil Safety

* Follow the manufacturer's directions when using oven

cooking bags.

• This appliance has been tested for safe performance using conventional cookware. Do not use any devices or accessories that are not specifically recommended

in this guide. Do not use add-on oven convection systems. The use of devices or accessories that are not

:SAFETY

expressly recommended in this guide can create serious safety hazards, result in performance problems, and reduce the life of the components of the appli-

ance.

* Only certain types of glass, glass/ceramic, ceramic,

earthenware, or other glazed utensils are suitable for oven service without breaking due to the sudden change in temperature. Follow utensil manufacturer's instructions when using glass.

Cleaning Safety

* Turn off all controls and wait for appliance parts to

cool before touching or cleaning. Clean with caution. Use care to avoid steam burns if a wet sponge or cloth is used to wipe spills on a hot surface. Some cleaners can produce noxious fumes if applied to a hot surface.

* Clean only parts listed in this guide.

Self-Clean Oven

* Do not clean door gasket. The door gasket is essential

for a good seal. Care should be taken not to rub, damage, or move the gasket.

• Before self-cleaning the oven, remove broiler pan, oven racks and other utensils, and wipe off excessive spillovers to prevent excessive smoke or flare ups.

Important Safety Notice and

Warning

The California Safe Drinking Water and Toxic Enforce-

ment Act of 1986 (Proposition 65) requires the Governor of California to publish a list of substances known to the

State of California to cause cancer or reproductive harm,

and requires businesses to warn customers of potential exposures to such substances.

Users of this appliance are hereby warned that when

the oven is engaged in the self-clean cycle, there may

be some low-level exposure to some of the listed substances, including carbon monoxide. Exposure to these substances can be minimized by properly venting the oven to the outdoors by opening the windows and/

or door in the room where the appliance is located

during the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS:

Never keep pet birds in the kitchen or in rooms where the fumes from the kitchen could reach. Birds have a

very sensitive respiratory system. Fumes released during

an oven self-cleaning cycle may be harmful or fatal to

birds. Fumes released due to overheated cooking oil, fat,

margarine and overheated non-stick cookware may be

equally harmful.

• Do not use oven cleaners or oven liners of any kind in or around any part of the self-clean oven.

Save These Instructions for Future Reference

Note: For microwave oven operation (select models) refer to the use and care guide packed in the micro-

wave oven.

OVENCO KiNG

Control Panel

A B C

UPPER OVEN

CANCEL Convect Bake

, i I I

Oven More

Light Options Clean Broil

Oven

Options Clean Broil

LOWER OVEN

The control panel isdesigned for ease in programming. The display window shows options for each function and moves from step to step through the programming process. In double ovens, Upper Ovenor Lower Oven isdisplayed to indicatewhich oven isbeing

programmed. Control panel features vary by model. Oven display above isa double oven programmed for bake and broil operations.

Function pads Lower oven

Function pads Upper oven

Quickset Pads

Display

window

Favorites

i:i_i!i!iiE

Help

Setup

Number pads

Use to program the lower oven for

double wall ovens.

Use to program the upper oven for

single and double wall ovens. Use to select options in display

window (next to display window on both sides).

Displays oven functions, options and time of day.

Use to access, program or save baking cycles.

Press for on-screen help.

Use to view or change factory default settings.

Use to enter time and temperature, or to enter Favorites names.

-O

-©

I_JENN-AIR

Up or Down arrows indicate additional screens with additional options. Pressthe Quickset pads next to the arrows to scroll

through the display.

Note: Four seconds after entering the function, option, number or letter, the function will automatically be en-

tered. If more than 30 seconds elapse between steps in programming, the function will be canceled and the

display will return to the previous display.

EF G kl

m I

! 2 3

4 5 6

GH_ JKL MNO

setup- 7 8 9

PQRS IUV WXYZ

Back 0 Enter

l ..... J

ABC DEE

rock

0 ©

Quickset Pads

Quickset pads are located on each side of the display window and are used to select the desired function or option in the

display window. To select the option or function, press the Quickset pad next to the word.

If you need to back out of a function or option in the display, press the Back pad. When your programming is complete,

press the Enter pad or wait four seconds and the function will

start automatically.

Clock

Setting the Clock:

Press the Setup pad. Setup ii

Select Clock using the Quickset pads.

Select Time.

Enter the time using the number pads.

Press Enter.

Select AM or PM in 12 hour mode. (For 24 hour clock, see page 5.)

Select Set.

To exit the Setup mode, press Setup.

OVENCO KiNG

Entering the day of the week:

1. PressSetup pad. ,......................

2. Select Clock.

3. Select Day.

4. Select Back or Fwd to scroll through the days.

5. Select Set.

6. To exit the Setup mode, press Setup.

Canceling the clock/day of week display:

1. PressSetup pad. ..........................

2. PressClock. i' Setup"

3. Pressthe Down arrow to scroll to the next screen.

4. Select Disable.

5. Select Off to turn the clock display off, or select On to turn

the clock display on.

6. Select Set.

7. To disable the day of week display, select OFFor select ON

to turn the weekday display on.

8. Select Set.

9. To exit the Setup mode, press Setup.

To set the clock for a 12 or 24 hour format: The clock can be set to display time in either a 12 hour or 24

hour format.

1. Pressthe Setup pad.

2. Select Clock.

3. Use the down arrow to scroll to the next screen.

4. Select 12/24 Hr.

5. Select 12 Hr or 24 Hr.

6. Select Set.

7. PressSetup to exit Setup mode.

Setup

\ ......................................

Timers

Setting the Timers {[Timer 1 or Timer 2):

1. PressTimer 1 or Timer 2. TIMERi

2. Select Time.

3. Pressone of the displayed times using the Quickset pads,

or press the number pads to enter the desired time.

Changing the amount of time entered once the

Timer starts:

1 Pressthe Timer 1 or Timer 2 pad ONCE. j

2. Pressthe displayed times on the Quickset On/Off

pads until the desired time is entered. .................................

3. Pressthe number pads to enter the new desired time.

4. PressEnter.

TIMER 1

Canceling the Timer:

1. Pressthe Timer 1 orTimer2 pad TWICE. _" TIMER1 ' OR , On/Off /

2. Pressthe Timer 1 or Timer 2 pad ONCE and Press CANCEL on the Quickset pads.

Changing the Timer format:

The Timers can be set to display hours and minutes (HR/MND

or minutes and seconds (MN/SEC_).

1. Pressthe Setup pad. Setup _:

2. Select the Down arrow and ...................................

scroll until you see Timer Format.

3. Select Timer Format.

4. Select HR/MN or MN/SEC.

5. Select Set.

6. PressSetup to exit Setup mode.

Changing the Timer beeps:

The signal beeps for Timer 1 and Timer 2 can be changed. The options available are two beeps every thirty seconds, two

beeps every sixty seconds or 1 beep only. The default setting

isOne Beep. ...........................,

1. Pressthe Setup pad. ( Setup J

2. Select the down arrow to scroll down until "Tones" is displayed.

3. Select Tones.

4. Select Timers.

5. Select the desired timer beep format (2-30 sec., 2-60 sec. or 1 Beep).

6. Select Set.

7. PressSetup to exit Setup mode.

Note: Each press of the displayed time choices adds

additional time. For example, pressing "10 min" three times

provides 30 minutes on the timer (0:30D.

4. Press Enter.

OVENCO KiNG

Locking the Control and Oven Door

The oven control and oven door can be locked to prevent accidental programming. Ifan oven function is currently

being used, the control and door cannot be locked.

To lock the control and door:

Pressthe Back and Enter pads at the same time, holding for

three seconds or until "Locked" appears in the display.

To unlock the control and door:

Pressthe Back and Enter pads at the same time, holding for

three seconds. The time of day will appear in the display when the control and door are unlocked.

Back 0 Enter

l Space 1

-- !ocl<

Baking Notes:

If more than thirty seconds elapse between pressing a pad and pressing a number pad, the display will return

to the previous display. Whenever the temperature appears in the display, the

oven isheating.

To recall the set temperature during preheat, press the

Bake pad.

To change the oven temperature during cooking, press the Bake pad and select a displayed temperature or use

the number pads to enter the desired temperature. The oven will automatically shut off after 12 hours if it is

accidentally left on. To set a Sabbath Mode, see Setup

Sabbath Mode, page 21.

Baking

To set Bake:

1. Pressthe Bake pad.

2. Select the oven temperature using the Quickset pads. OR

Enter the desired temperature using the number pads. Press Enter to set.

The temperature can be set from 170° to 550° in

5° increments.

After three seconds, the oven will begin to preheat.

"Upper Oven" and/or "Lower Oven" and " Bake Preheat"

will appear in the display along with 100° or the actual

oven temperature, whichever is higher.

Bake

\ ..............................

The temperature in the display will increase in 1o

increments until the oven reaches the preset tempera- ture. Allow about 15 minutes for the oven to preheat.

, When the oven is preheated, the oven will beep and

"Preheat" will no longer be displayed.

3. At the end of cooking, turn the oven off by pressing the

CANCEL pad. Removefood from the oven. _.........................-,

The oven will continue operating until the _i'CANCEL CANCEL pad is pressed. ,

........................... /'

Bake Options

Cook & Hold and Delay options are available when baking.

When using the Cook & Hold option, the oven begins to heat

immediatelyafter the control has been set. Then, the oven cooks for a specified length of time. When that time has

elapsed, the oven will keep the food warm for up to an hour

then automatically turn off. When using Delay, the oven begins to cook later in the day.

Set the amount of time that you want to delay before the oven turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time. When that time has elapsed, the oven will keep the food warm for up to an hour then automatically turn off.

O ©

To set Cook & Hold:

After Bake has been programmed, press Options using the

Quickset pad.

Select CooWHold.

Select the amount of time you want to bake by pressing the Quickset pads or the number pads.

The oven will cook for the selected time, then keep food warm for one hour.

O ©

OVENCO KiNG

To set a Delay:

1. After Bake has been programmed, press Options using the Quickset pad.

2. Select Delay.

3. Select the amount of time you want to delay the start of cooking using the displayed times or the number pads.

4. Select the amount of time you want to cook using the displayed times or the number pads.

5. The display will show "Delay Bake", the temperature, the delay time and the cook time.

Note: Both Cook & Hold and Delay also can be accessed |

through More Options pad.

Convect (select models)

Convection uses a fan to circulate hot air evenly over, under and around the food. As a result, foods are evenly cooked

and browned, often in shorter times, at lower temperatures and with the flexibility of using more than one rack at a time.

Convect Options

Cook & Hold and Delay options are available when convect

cooking. See page 6 for informationon how to program a Cook & Hold or Delay option.

Suggested Foods for Convect Selections

Multiple-rack

Baking of

Cookies/Biscuits

Breads

Casseroles

Tarts/Tortes

Cakes

Convect Bake

To set Convect Bake:

Press the Convect pad. _Convect j_

Select Bake using the Quickset pads.

Select the oven temperature using the Quickset pads OR

Enter the desired temperature using the number pads. Press Enter to set.

BeefSteaks

FishSteaks

FishFiletes

PorkChops

ghicken Breasts

Shrimp

Whole Chicken

Whole Turkey

Vegetables

Pork Roasts Beef Roasts

(select models)

Cream Puffs

FrozenPie Turnovers

Puff Pastry

Convection Notes:

The oven control comes from the factory set for Auto Convect Conversion. When using Convect Bake and Convect Pastry enter the conventional baking tempera-

ture. The control automatically converts the temperature to 25° lessthan the conventional temperature.

For Convect Roast, enter the conventional roasting temperature and time. The control then lets you know

when 75% of the time has elapsed and alerts you to check the food for doneness.

To turn Auto Convect Conversion off, see page 20.

The temperature can be set from 170°Fto 550° F degrees

in 5° increments.

After three seconds, the ovenwill begin to preheat. "Upper

Oven" and/or "Lower Oven" and "Bake Preheat" will appear in the display along with 100° or the actual oven

temperature, whichever is higher.

The temperature in the display will increase in 1oincre-

ments until the oven reaches the preset temperature. Allow about 15 minutes for the oven to preheat.

When the oven is preheated, the oven will beep and

"Preheat" will turn off and "Bake" will be displayed. Place food in the oven.

At the end of cooking, turn the oven off by pressing the

CANCEL pad. Remove food from the oven. The oven will continue operating until the CANCEL pad is :, LJCANCE

pressed.

OVENCO KiNG

Convect Roast (select models)

To set Convect Roast:

1. Place food in the oven.

2. Pressthe Convect pad.

3. Select Roast.

Select the oven temperature using the Quickset pads. OR

Enter the desired temperature using the number pads. Press Enter to set.

Convect

Enter Cook/Hold will appear in the display.

Enter Cook & Hold time using the Quickset pads. OR

Enter the desired time using the number pads.

The temperature can be set from 170° Fto 550° F

degrees in 5° increments.

After three seconds, the oven will begin to heat. "Upper

Oven" and/or "Lower Oven" and "Convect Roast" will appear in the display along with 100° or the actual oven

temperature, whichever is higher.

The temperature in the display will increase in 1oincre-

ments until the oven reaches the preset temperature.

5. At 75% of the cooking time the oven will beep to let you know to check food. Check food using a meat thermom-

eter. If food is done, take food out of oven and press CANCEL pad to turn oven off.

If food is not done, continue roasting. Once the set time has elapsed the oven will automatically

go into Keep Warm mode for 1 hour. If food is taken from the oven before the hour has elapsed press CANCEL pad.

Convect Pastry (selectmodels:)

Convect Pastry is designed to bake pastry items such as

frozen pies, turnovers, cream puffs and puff pastry.

1. Pressthe Convect pad. f Convect _`

2. Select Pastry.

3. Select the oven temperature using the Quickset pads. OR

Enter the desired temperature using the number pads. Press Enter to set.

The temperature can be set from 170° Fto 550° F

degrees in 5° increments.

After three seconds, the oven will begin to preheat.

"Upper Oven" and/or "Lower Oven" and "Convect Preheat" will appear in the display along with 100° or

the actual oven temperature, whichever is higher.

The temperature in the display will increase in 1oincre-

ments until the oven reaches the preset temperature.

Allow about 15 minutes for the oven to preheat.

, When the oven is preheated, the oven will beep and

Preheat will turn off and Bake will be displayed.

At the end of cooking, turn the oven off by pressing the

CANCEL pad. Remove food from the oven.

The oven will continue operating until the

CANCEL pad is pressed.

(CANCELII_

OVENCO KiNG

Convect Broil (selectmodels )

For best results when broiling, use a pan designed for broiling. Oven door should be closed when broiling. Preheat-

ing is not necessary.

To set

Convect Broih

Place the oven rack in the proper rack position. (See

Broiling Chart, page 10.) j,.....

Press the Convect pad. Select Broil.

Select HIGH - 550° F for high broil. OR

Select LOW - 450° F for low broil.

The oven has a variable broil feature, which means that

a lower broil temperature can be selected (300°-550°F_).

To select a lower temperature, press the appropriate

number pads. Press Enter to set the lower temperature.

Place food in the oven. Close the oven door.

Press the CANCEL pad when broiling is ii CANCEL ) done. , J

Convect i;

Broil

For best results when broiling, use a pan designed for broiling.

To set Broil:

1. Place the oven rack in the proper rack position (see Broiling Chart on page 10).

2. Place food in the oven. .................,,

3. Pressthe Broil pad.

4. Select HIGH - 550° Ffor high broil. OR

Select LOW - 450° F for low broil.

The oven has a variable broil feature which means that

a lower broil temperature can be selected (300°-550°F).

To select a lower temperature, pressthe appropriate

number pads. Press Enter to set the lower temperature.

5. Close the oven door. ..................................

6. Pressthe CANCEL pad when broiling is done. ,_....

Broil Notes:

See Broiling Chart, page 10,for foods and broiling times.

If more than 30 seconds elapse between pressing the Broil pad, Quickset pads,or number pads, the oven will

not be set and the display will return to the previous display.

"High" is used for most broiling. Use a lower broil

temperature when broiling longer cooking foods. The

lower temperature allows food to cook to the well done stage without excessive browning.

Expect broil times to increase and browning to be slightly lighter if the appliance is installed on a 208 volt

circuit.

Food should be turned halfway through broiling time.

Broil times may be longer when lower broiling tempera-

tures are selected.

CANCEL

Convect broiling is generally faster than conventional broiling. Check for doneness at the minimum recom-

mended time.

OVENCO KiNG

Broiling Chart

Beef (broiled to 160° F)

6 Hamburgers, 1/2" thick 2 Ribeye Steaks, 1" thick 2 New York Strip Steaks, 1" thick

2 T-Bone Steaks, 1" thick

10-12

18- 22 18- 22

18- 22

minutes minutes minutes

minutes

12 - 14 minutes 13- 16 minutes 13- 17 minutes

16- 18 minutes

40 40

Poultry (broiled to 170° Fon Low) Low

4 Boneless/Skinless Breasts 12 - 15 4 Bone-in Chicken Breasts 20 - 23

Broil minutes minutes

Low Broil

10 - 12 minutes

18-20 minutes

Pork (broiled to 160° F)

4 Boneless Pork Chops, 1" thick 4 Bone-in Pork Chops, 1" thick

Ham Slice, 1 inch thick

Fish ([broiled to 140° F)

4 Swordfish Steaks, 1" thick 2 Halibut Steaks, 1" thick

Orange Roughy, 1 "thick

Shrimp (16-20 ct per lb.)

2 Salmon Fillets, 1/2" thick 2 Salmon Steaks, 1" thick

20 - 28 minutes 25- 28 minutes

16- 18 minutes

8- 12 minutes 10 - 12 minutes 10 - 12 minutes

8 - 10 minutes

8- 12 minutes

17- 19 minutes 17- 19 minutes 15 - 17 minutes

8-12 minutes 9-11 minutes

9 - 11 minutes

6 - 8 minutes 11 - 13 minutes 11 - 13 minutes

* The use of the offset rack isdenoted in the chart as an "o" after the rack position number.

NOTE: To reduce browning and excesssmoke when broiling, rack 30 can be used instead of rack 40.

40 4O

30 30

30 30 30 30 30 30

OVENCO KiNG

Oven Racks

Single and Double Convection Ovens - two flat racks and

one offset rack were packaged for each oven. Single and Double Non=Convection Ovens - one flat and

one offset rack were packaged for each oven.

To remove:

1. Pull forward to the "stop" position.

2. Lift up on the front of the rack and pull out.

To replace:

1. Place rack on the rack support in the oven.

2. Tilt the front end up slightly; slide rack back until it clears the lock-stop position.

3. Lower front and slide into the oven.

Notes:

The use of the offset rack is denoted in the list at left as an "o" after the rack position number.

Do not place food on a flat rack in position one when the offset rack is in position two. When the offset rack is

in position two, a flat rack placed in position one may contact the offset rack when sliding in or out of the oven.

When baking on two or three racks, check foods at the minimum suggested time to avoid over-browning or

over-cooking.

Do not cover an entire rack with aluminum foil or place foil on the oven bottom. Baking results will be affected and

damage may occur to the oven bottom.

Easy Rack (selectmodels)

Select wall oven models are equipped with an EasyRack. This

rack offers a convenient place to grasp bakeware when

taking it out of the oven.

Rack

RACK 4: Can be used

for two- or three-rack

baking. RACK 40: Used for

broiling. RACK 3: Used for

casseroles and most

baked goods. RACK 30: Used for

most baking and

three-rack baking.

RACK 2: Used for roasting small cuts of meat and two-rack baking.

RACK 20: Used for small cuts of meat and casseroles. RACK 1: Used for roasting large cuts of meat and three-rack

baking.

RACK lo: Not recommended.

Positions

_ 4flat

3offset

1flat

Three-rack Convection

Cooking (select models)

Notes:

• The Easy Rack is to be used in ovens with a hidden bake element only. Do not use the Easy Rack if your oven has

an exposed bake element. Use the Easy Rack only in the oven in which it was

purchased.

OVENCO KiNG

Create-A-Space TMHalf Rack

I:select models:)

Select wall oven models are equipped with a convertible _

half rack. The left side of

the rack can be removed to accomodate a large

roaster on the lower rack. The right side of

the rack is still available to hold a _

casserole dish.

c:::D

Oven Light

The oven light automatically comes on whenever the oven

door is opened. When the door is closed, pressthe Oven Light pad to turn the oven light on and off. A beep will sound every

time the Oven Light pad is pressed.

Oven Vent

The oven vent is located below the oven door on single wall

ovens, and below the bottom door on double wall ovens.

When the oven is in use, the area near the oven vent may

become hot enough to cause burns. Do not block the vent opening for best baking results.

Oven Fans

A cooling fan will automatically turn on whenever the oven is operating. It is used to help keep internal parts onthe control

panel cool. The fan may continue to operate after the oven has been turned off. The fan will automatically turn off when

parts have cooled. This is normal.

A convection fan (select models) is used to circulate hot air

in the oven when the convection feature is selected. It

automatically turns on whenever the Convect pad is pressed and will turn off when Convect is canceled.

Notes:

The removable section of the rack can be used as a

cooling rack or trivet. Make sure rack is cool before removing from the oven.

Make sure oven is cool before removing or reinstalling the half rack.

Do not use cookware that extends beyond edge of rack. For best results, allow two inches between the pan

placed on the rack and the oven side wall. Use caution when removing items from the half rack to

avoid burns. Carefully remove items from the lower rack to avoid

disturbing the half rack.

Note: The convection fan will automatically stop whenever the oven door is opened.

PT|

More Options

Cook & Hold

0 0

1. Pressthe More Options pad. More ",,

2. Select Cook/Hold. _,Options ;

3. Enter cook time using Quickset pads or the number pads.

4. Select Bake or Convect.

5. When Bake is pressed, select the temperature using Quickset pads or the number pads.

6. When Convect is pressed, select Bake, Broil, Roast or Pastry, then select the desired temperature using the

Quickset pads or the number pads.

The oven will cook for the selected time, then Keep Warm for one hour. The oven will automatically turn off.

Delay

1. Pressthe More Options pad. More

2. Select Delay. ........................................

3. Select Delay time using Quickset pads or the number pads.

4. Select Bake, Convect or Clean.

Options/

To set Delay Clean:

1. "Remove Racks from Oven" will show in the display. Remove the racks from the oven and select Continue.

2. Select Light, Medium or Heavy soil level using the Quickset pads. There is a brief delay while the door locks.

3. "Delay Clean", the cleaning time, the delay time and unlock time (based on the selected soil level) will show in

the display.

For more information on self-cleaning, see page 24.

Proofing (select models)

The Proofing feature can be used to raise yeast-based bread

products prior to baking. There are two proofing methods available - Rapid and Standard.

Standard proofing in the oven protects dough from room temperature changes or drafts that commonly affect proofing

done on the countertop. Rapid proofing provides faster proofing results than

countertop or standard proofing, without harming the yeast.

1. PressMore Options pad. .....................................................

2. Select Proofing. ', Options /

3. Select Rapid or Standard.

When proofing is complete, remove the dough from the

oven and press the CANCEL pad.

.... More "',

To set Delay Bake:

1. Select from the displayed temperatures or use the number pads to enter the temperature.

2. Select the time to cook from the displayed times or use the number pads to enter the cooking time.

3. The display will show "Delay Bake", the preset tempera- ture, the delay time countdown and the cook time.

To set Delay Cenvect:

1. Select Bake, Roast or Pastry.

2. Select from the displayed temperatures or use the number pads to enter the temperature.

3. Select the time to cook from the displayed times or use the number pads to enter the cooking time.

4. The display will show "Convect Delay", the preset tempera- ture, the delay time countdown and the cook time.

Proofing Notes:

, For any dough that requires one rise,either Standard or

Rapid Proofing can be used.

, For dough requiring two rises,Standard Proofing must

be used for the first rising period. Either Standard or Rapid Proofing can be used for the second rise.

, If oven temperature is too high for proofing, "Oven

Cooling" will appear in the display.

Keep Warm (select models)

The Keep Warm feature is used to safely keep hot foods warm

or for warming breads and plates. _.................

1. PressMore Options pad. , Options

2. Pressthe down arrow to scroll down. .........................

3. Select Keep Warm.

PTi

4. Select one of the displayed temperatures or enter desired temperature using the number pads.Temperatures can be selected between 145°and 190° F.

5. "Warm Preheat" and the temperature will be displayed.

6. When oven has preheated, a beep sounds and "Warming" and the temperature will be displayed.

7. When finished, press the CANCEL pad and remove food or plates from the oven.

To Warm Dinner Rolls:

Cover rolls loosely with foil and place in oven.

, Press More Options pad. , Select Keep Warm.

, Select 170° temperature. Warm for 12-15 minutes.

To Warm Plates:

, Place two stacks of up to four plates each in the oven. , Press More Options pad. , Select Keep Warm.

, Select 170° temperature. , Warm for five minutes. Turn off the oven by pressing the

CANCEL pad and leave plates in the oven for 15minutes

more. , Use only oven-safe plates, check with the manufacturer. , Do not set warm dishes on a cold surface as rapid tempera-

ture changes could cause crazing or breakage.

Keep Warm Notes:

, Food should be hot when placed in oven.

For optimal food quality, foods should be kept warm for no longer than 1 hour.

To keep foods from drying, cover loosely with foil or a glass lid.

/ ...............................

/ More

, Options/

CANCEL )

\ ....................

Drying (:select models)

For best results, use a drying rack. A drying rack allows air to circulate evenly around the food.

The convection fan will operate during the drying procedure.

To set Drying:

Press More Options pad. Options j

Press the down arrow to scroll down.

Select Drying.

Select a displayed temperature or enter atemperature with the number pads. Temperatures can be set between

100° Fand 200° F.

5. "Drying" and the temperature will be displayed.

6. Remove food from oven and press CANCEL CANCEL) pad when drying is done.

Follow the Drying Guide on page 15 for drying times. Check foods at minimum times given. Cool foods to room tempera- ture before testing for doneness.

Drying Notes:

To purchase a drying rack, contact your Jenn-Air dealer

for the "DRYINGRACK" Accessory Kit or call 1-800-

JENNAIR.

Most fruits and vegetables dry well and retain their color

when dried at 140° F.Meat andjerky should be dried at

145° - 150° F. For optimal flavor, dry herbs at 100°F, however, at this lower temperature expect extended

drying times of up to 8 hours.

The length of drying times vary due to the following: Water and sugar content of food, size of food pieces,

amount of food being dried, humidity in the air. Check foods at the minimum drying time. Dry longer if

necessary. Fruits that turn brown when exposed to air should be

treated with an antioxidant. Try one of the following methods:

1. Dip fruit in a mixture of two parts bottled lemon juice to one part cool water.

2. Soak fruit in a solution of 1 tsp. ascorbic acid or commercial antioxidant to 1 quart of cold water.

Foods may drip during the drying process. After drying high acid or sugary foods, clean the oven bottom with

soap and water. The porcelain oven finish may discolor if acidic or sugary food soils are not wiped up prior to high

heat or a self-cleaning cycle. More than one rack of food may be dried at the same

time. However, additional drying time is needed. Refer to other resources at your local library or call your

local County Extension service for additional information.

PT|

Drying Guide (:selectmodels)

Apples*

Apricots*

Bananas*

Cherries

Nectarines

and Peaches*

Pears*

Pineapple

Orange and

Lemon Peel

Firm varieties: Graven

Stein, Granny Smith, Jonathan, Winesap,

Rome Beauty, Newton. Blenheim/Royal most

common. Tilton also good. Firm varieties

Lambert, Royal Ann, Napoleon, Van or Bing.

Freestone varieties.

Bartlett Fresh or canned.

Select rough-skinned fruit.

Do not dry the peel of fruit marked "color added".

Wash, peel if desired, core and slice

into 1/8" slices.

Wash, halve, and remove pits.

Peel and cut into 1/4" slices. Wash and remove stems. Halve and

remove pits. Halve and remove pits. Peeling

is optional but results in better-looking dried fruit.

Peel, halve and core.

Wash, peel and remove thorny eyes.

Slice length wise and remove the small core. Cut crosswise into

1/2" slices.

Wash well. Thinly peel the outer

1/16 to 1/8" of the peel. Do not use the white bitter pith under the peel.

4-8 hours

18-24 hours

17-24 hours.

18-24 hours.

24-36 hours

Canned: 14-18 hours Fresh: 12-16 hours

]-2 hours

Pliable to crisp. Dried apples store best when they are slightly crisp.

Soft, pliable.

Pliable to crisp. Pliable and leathery.

Pliable and leathery.

Soft and pliable. Soft and pliable.

Tough to brittle.

Tomatoes

Plum, Roma

Halve, remove seeds. Place tomatoes

12-18 hours

Tough to crisp.

skin side up on rack. Prick skins.

Carrots

Danvers Half Long, imperator, Red Cored Chantenay

Do not use carrots with woody fiber or pithy core. Wash, trim tops and peel if desired. Slice crosswise or

4-8 hours

Tough to brittle.

diagonally into 1/4" slices. Steam blanch for 3 min.

Hot Peppers

Ancho, Anaheim

Wash, halve and seed. Prick

skin several times.

4-6 hours

Pods should appear shriveled dark red and crisp.

Parsley, Mint, Rinse in cold water. Pat dry with a 1-3 hours Brittle and crumbly. Cilantro, Sage, paper towel. Leave stems on until Oregano leaves are dry, then discard.

Basil Cut leaves 3 to 4" from top of plant 2-5 hours Brittle and crumbly.

just as buds appear. Rinse leaves in

cold water.

*Fruits requiring anantioxidant to prevent discoloration and loss of nutrients. Refer to the notes on page 14for specific methods.

** 12 Hour Offwill not occur during drying functions.

Probe (select models:)

SINGLE OR UPPER OVEN ONLY

Using the probe supplied with your wall oven assures excel- lent roasting results every time. The probe can be used in the

upper oven only for double ovens.

Insert the probe into the food item. For meats the probe

tip should be located in the center of the thickest part of the meat and not intothe fat or touching a bone.

Insert the probe plug into the receptacle located on the top left of the oven. Besure to

insertplug intothe receptacle

all the way.

Press More Options pad.

Pressthe down arrow to

scroll down.

Select Probe.

/ More ",,

,,Options

Set the internal food temperature desired by selecting one of the displayed temperatures or enter the tempera- ture using the number pads. The probe temperature can

be set from 100° - 185° F.

Select Bake or Convect.

Set the oven temperature by selecting one of the dis-

played temperatures or enter the temperature using the number pads.

When Convect is selected:

Select Bake, Roast or Pastry.

Set the oven temperature by selecting one of the displayed temperatures or enter the temperature using

the number pads. The display will briefly show the selected temperatures

for the oven and probe. After 30 seconds, the display will show the actual oven

temperature and actual probe temperature.

9. When the selected internal temperature of the food has been reached, the oven will shut off and a beep will

sound.

10. Remove the probe from the oven receptacle. The probe

will be hot. Hold probe plug with an oven mitt or

potholder when removing from the oven.

Probe Notes:

The probe must be removed from the oven when it is not

being used. Because of the excellent insulation of the oven, the

retained heat continues to cook the food after the beep has sounded and the oven has turned off. Forthis

reason, it is important to remove the food from the oven as soon asthe beep sounds.

Use the handle of the probe for inserting or removing. Do not pull on the cable.

The probe is hot after cooking - use a potholder or

oven mitt to remove.

To protect the probe, if meat is not completely thawed,

insert probe after 1-2 hours of roasting.

To clean cooled probe, wipe with a soapy dishcloth.

Do not submerge probe in water or wash in dish=

washer.

Note: If the probe is removed from the oven receptacle at

any time during the cooking process, the program will be canceled and the oven will turn off.

When Bake is selected:

The display will briefly show the selected temperatures for the oven and probe.

After 30 seconds, the display will show the actual oven temperature and actual probe temperature.

Suggested Internal Food Temperatures

Ground Beef 160° F Fresh Beef,Veal, Lamb Medium Rare 145° F

Medium 160° F

Well Done 170° F

Chicken, Turkey Whole 180° F

Breast 170° F

Pork Medium 160° F

Well done 170° F

Ham,precooked 140° F

PT|

Thaw and Serve (]select models)

Use Thaw and Serve to thaw frozen foods that require

thawing, but not cooking, before serving.

To set Thaw=Serve:

1. Place food in the oven.

2. Press More Options pad.

/" More ",

Options /

Thaw and Serve Chart

Whole Pies & Cakes Pies: Lemon meringue,

cream, pecan,chocolate, sweet potato, Frenchsilk. Cakes: Vanilla, chocolate,

coconut, and three-layer cakes, pound cake,

Boston Cream Pie

mndividual Servings: Slices of pie,slices of cake,

other individual desserts, eclairs,cream puffs

1.Removefrozen food from outer carton and wrapping.

2.Placefrozen food on rack in middle of oven.

3.Thaw-Serve 15 minutesfor cakes and 30 minutes for pies.

4. Removefrom oven.

5.Slice into individual-size servings and placeon plates.

6.Return plates to oven.

7.Thaw-Serve for 10 to 30 minutes.

1.Removefrozen food from container.

2.Place on plate.

3.Place plate on rack in middle of oven.

4.Thaw-Serve for 10 to 30 minutes.

3. Pressthe down arrow to scroll down.

4. Select Thaw-Serve.

5. Select number of minutes to thaw.

6. "Thaw-Serve" will be displayed.

7. When finished, press the CANCEL pad and remove food from the oven.

Note: This feature is not meant for thawing meats or other

foods that need to be cooked before serving.

• Thawing for 30 minutes makesit easier to slice whole pies, cakes and

cheesecake.

• Layercakeswill require only 15 minutes before slicing.

• Sizeand texture of food being thawed will affect Thaw-Servetime.

• Larger ordenser desserts maytake longer to thaw.

• Cake slices will thaw quicker than pies. Sweet potato pieslices may require 20

to 30 minutes.

CANCELI:,

Cheesecake

DeE Spirals

* Only "Thaw and Serve" or "Ready to Serve" frozen foods can be used with this feature. DO NOT attempt to thaw frozen meats,

poultry or seafood.

** It is not necessary to preheat the oven.

1.Removefrozen food from outer carton and wrapping.

2.Placefrozen food on rack in middle of oven.

3.Thaw-Serve for 30 minutes.

4. Removefrom oven.

5.Slice into individual-size servings and placeon plates.

6.Return plates to oven.

7.Thaw-Serve for up to 15 minutes if desired.

1.Removefrozen food from container.

2.Place on plate.

3.Place plate on rack in middle of oven.

4.Thaw-Serve for 10 to 15 minutes.

FAVORITES

Favorites

Favorites stores up to 10 of your favorite recipes. Convection

ovens come with five preprogrammed recipes.

To select a recipe from the preset Recipe List:

1. Press Favorites Pad.

2. Select Recipe List.

/ .....

Favorites :,

0 ©

3. Select desired recipe on screen or press arrow key to scroll to the desired recipe.

4. Once the recipe is selected, oven will begin preheating to the set program.

* You may select Options to add Cook & Hold or Delay.

5. When finished, press the CANCEL pad and remove food from the oven.

To Save the Last Recipe Completed:

(Bake, convect bake, convect roast, convect pastry, convect broil, drying, keep warm, proofing)

1. Press Favorites Pad.

2. Select Save Last.

4. Aftereach desired letter appears, wait three seconds or press enter before moving onthe next letter.

* Up to 15 letters including spaces can be used.

5. Select Set. * The recipe settings will be displayed.

6. Select Continue to go back to the Favorites menu.

7. Select Favorites pad to exit the Favorites menu.

To Create a New Favorite Recipe:

1.PressFavoritespad. ,u vorites,

2. Select Create New.

3. Enter the name using the keypads. * For example, to save lasagna, press the <JKL> pad three

times for "L"; Press the <ABC> pad once for "A"; press the <STU:> pad once for "S". Continue until you've

finished the word.

* After each desired letter wait three seconds or press

enter before moving on the next letter.

* Up to 15 letters including spaces can be used.

4. Select Set to save name.

5. Select cooking mode, such as Bake, Convect Bake, Convect Roast, etc.

6. Select the oven temperature using the Quickset pads. OR

Enter the desired temperature using the number pads.

7. Select Continue.

8. Add CooWHold by selecting Yes or No.

9. Select Continue to go back to the Favorites menu.

10.Press Favorites pad to exit the Favorites menu.

cont.

3. Enter the name using the keypads. * For example, to save lasagna, press the <JKL> pad three

times for "L"; Press the <ABC> pad once for "A"; press the <STU> pad once for "S". Continue until you've

finished the word.

FAVORITES

To Edit a Saved Recipe:

O ©

Press Favorites Pad.

Press arrow key to scroll down.

Select Edit Recipe.

4. Select desired recipe to edit. You may need to press arrow keys to find desired recipe.

5. Select Set.

6. Change recipe settings as desired.

7. Select Continue.

8. Press Favorites pad to exit Favorites menu.

Favorites"

To Delete a Favorite Recipe:

1. PressFavorites pad. .....................

2. Pressarrow keys to next screen to Select Delete Recipe.

3. Find recipe to be deleted by selecting Fwdor Bwd. Once recipe is displayed, select Delete.

4. The Control will ask again to make sure you want to delete that recipe. Select Yes or No.

5. PressFavorites pad to exit Favorites menu.

To exit out of Favorites at any time, press the Favorites pad.

Setup

1. Pressthe Setup pad.

2. Use the arrows to scroll through the Setup options.

3. Select the desired option using the Quickset pads.

Auto Convect Conversion Notes:

,, When using Convect Bake and Convect Pastrywith the

Auto Convect Conversion option turned off, reduce the set temperature by 25° F.

If Convect Roasting with the Auto Convect Conversion option turned off, check food at 75% of the conventional

time.

Setup Notes:

', All setup option screens have a "Set" pad. Pressthe

desired option, then press the Set pad.

', To back out of ascreen without making any changes,

press the Setup pad. The display will return to the time

of day.

Clock

Use the Clock option to:

* Set the time of day.

Set day of week. Select AM or PM (12-hour mode only).

Choose a 12 or 24 hour clock display. Disable the clock display.

To reactivate Auto Convect Conversion:

1. PressSetup pad.

2. SelectAuto Convect. "................

3. Select ON.

4. Select Set.

5. PressSetup pad to exit the Setup menu.

Language

The language of the screens in the display window can be set to English, French or Spanish. To change the display lan-

guage from English:

1. PressSetup pad. : SetUp )

2. Select Language. '........................................'

3. Usethe arrow to scroll to next screen.

4. Select the desired language.

5. Select Set.

6. PressSetup pad to exit the Setup menu.

Auto Convect Conversion

(select models)

The oven comes from the factory setfor Auto Convect Conversion.

Auto Convect Conversion automatically reduces the set temperature by 25° for Convect Bake and Convect Pastry.

ForConvect Roast the control will alert you at 75% of the programmed roasting time to check foods for doneness.

To deactivate Auto Convect Conversion:

Press Setup pad.

Select Auto Convect.

Select OFF.

Select Set.

Press Setup pad to exit the Setup menu.

C/F

The displayed temperature scale can be changed from

Fahrenheit to Celsius.

To change the scale:

1. PressSetup pad.

2. Usethe arrow to scroll to the next screen.

3. Select C/F.

4. Select the desired temperature scale.

5. Select Set.

6. PressSetup pad to exit the Setup menu.

SETUP

Sabbath Mode

The oven is set to shut off after 12 hours if you accidentally

leave it on. The Sabbath Mode overrides the 12-hour shut-off

and can either be set to come on automatically or can be set

manually as desired.

To activate Sabbath Mode:

1. PressSetup pad.

2. Pressthe down arrow to scroll down.

3. Select Sabbath.

4. Select Auto or Manual. * Auto is used to automatically convert to Sabbath Mode

every Friday at 2 pm, and stay in Sabbath Mode for 76 hours.

* Manual sets the oven to Sabbath Mode instantly for 76

hours.

5. Select Auto or Manual as desired.

6. Select Yes or No.

7. Select Set.

Sabbath Mode Notes:

Temp Adjust

Oven temperatures are carefully tested at the factory. It is normal to notice some baking time or browning differences

between a new oven and an old one. As ovens get older, the oven temperature can shift.

You may adjust the oven temperature if you think the oven is

not baking or browning correctly. To decide how much to change the temperature, set the oven temperature 25° F

higher or lower than the temperature inyour recipes, then bake. The results of the first bake should give you an idea of

how much to adjust the temperature.

To adjust the oven temperature:

1. PressSetup pad.

2. Pressthe down arrow to _-.....................................

scroll down.

3. Select Temp Adjust.

4. Select upper oven or lower oven (select models). "Set temperature offset using the keypad" is displayed.

5. Enter the desired temperature change. The temperature can be increased or decreased by 5° to 35°.

6. Select "+/-" to indicate an increase or decrease in tem- perature. The temperature change is displayed at the top

of the window.

', The oven must be idle to program Sabbath Mode. * Sabbath Mode cannot be turned on if the keypads are

locked out or when the door is locked. If the oven is baking when Sabbath Mode is set, there

will be no audible beeps. All prompts, messages and beeps are deactivated when

the Sabbath Mode is active.

If the oven light is desired while in Sabbath Mode, it must be turned on before the Sabbath Mode is set.

When the Sabbath Mode is started, the temperature display will immediately show the set temperature,

rather than the actual oven cavity temperature. No preheat beep will sound.

,, The self-clean cycle and automatic door lock do not

operate during the Sabbath Mode.

* Pressing the CANCEL pad will cancel a Bake cycle,

however the control will stay in the Sabbath Mode.

7. PressEnter pad to accept the change.

The oven temperature does not need to be readjusted if there

is a power failure or interruption. Broiling and cleaning temperatures cannot be adjusted.

208/240V

For improved results when using Bake, the oven can be set

from 240V to 208V if your household is on 208V.

To set the oven to 208V:

1. PressSetup pad. (Setup

2. Pressthe down arrow to ".............................

scroll down.

3. Select 208/240V.

Select 208 or 240 using the Quickset pads.

Select Set.

ETUP

Tones (beeps)

The number of beeps heard at the end of cooking and at the end of timer operation and their volume can be adjusted.

To adjust the beeps:

1. PressSetup pad.

2. Use the down arrow to scroll down.

3. Select Tones.

To change the beeps at the end of cooking:

1. Select Cook.

2. Select 1-30 to hear one beep every thirty seconds. OR

Select 1-60 to hear one beep every sixty seconds. OR, use the down arrow to scroll down.

Select 1 Beep to hear one beep only at the end of cooking.

3. Select Set.

4. Pressthe Setup pad to exit.

To change the timer beeps:

1. Select Timers.

2. Select 2-30 to hear two beeps every thirty seconds. OR

12 Hr Shutoff

The oven will automatically turn off at the end of 12 hours if you accidentally leave it on.

To turn off this feature:

1. PressSetup pad. !Setup

2. Usethe down arrow ........................................

to scroll through the screens to 12 Hour Shutoff.

3. Select On or Off using the Quickset pads.

4. Select Set.

5. Pressthe Setup pad to exit.

Timer Format

The display format for the timer can be set from HRS/MN

(hours and minutes) to MIN/SEC (minutes/seconds).

To change the timer format display:

Press Setup pad. ..............................

Use the down arrow to scroll down.

Select Timer Format.

Select HRS/MIN or MIN/SEC using the Quickset pads.

Select Set.

Press the Setup pad to exit.

Select 2-60 to hear two beeps every sixty seconds. OR, use the down arrow to scroll down.

Select 1 Beep to hear one beep only at the end of the set time.

3. Select Set.

4. Pressthe Setup pad to exit.

To change the volume of the beeps:

1. Pressthe down arrow to scroll to the next screen.

2. Select Volume.

3. Select High-3 for the highest volume. OR

Select Med-2 for medium volume. OR

Select Low-1 for the lowest volume.

4. Select Set.

5. Pressthe Setup pad to exit.

Energy Saver

To save energy, the display can be set to go dark if it is not

being used.

To set the Energy Saver feature:

1. PressSetup.

2. Usethe down arrow to scroll down.

3. Select Energy Saver.

4. Select Off or On using the Quickset pads.

5. Select Set.

6. Pressthe Setup pad to exit.

Demo

When Demo is selected, you will see a short presentation

highlighting the features of your new Jenn-Air wall oven.

1. PressSetup pad.

2. Usethe down arrow to scroll down.

3. Select Demo.

4. Pressthe Setup pad to exit.

ELP

On screen help is available by pressing the Help pad on the control. The following Help topics are available when the oven

is idle:

Before You Call Tips

, Service

Function-specific help is available by pressing the Help pad

when the oven is operating.

Use the Quickset pads to select the Help section you want to

search. Under each section is a list of topics. Use the arrow

pads to scroll through the topics. Usethe Quickset pads to display the topic information.

To return to the previous screen, press Back. To exit Help,

press Help pad.

Service

This area of the oven control displays the Jenn-Air Customer Service toll-free phone number.

CARE CLEANING

Self-Clean Oven

The self-clean cycle uses above normal cooking temperatures to automatically clean the entire oven interior. The oven is

vented at the bottom of the oven door of single wall ovens and at the bottom of the lower door of double wall ovens.

Notes:

,, Both ovens cannot be self-cleaned at the same time in

double wall oven models.

* The oven light will not operate during self-clean.

Toprevent damage, do not clean

or rub the gasket around the oven

deer. The gasket isdesigned to seal in heat during the clean cycle.

Wipe up excess grease or spillovers

from the oven bottom to prevent

excessive smoking, flare-ups or flaming during the clean cycle.

Wipe up sugary spillovers and acidic spillovers such as lemon juice, tomato sauce or milk-based sauces. Porcelain enamel

isacid resistant, not acid proof. The porcelain finish may discolor if acidic or sugary spills are not wiped up prior

to a self=clean cycle.

To set Self=Clean:

1. PressClean pad.

2. "Remove racks from oven" will be displayed. Remove the racks.

3. Select Continue.

It is normal for flare-ups, smoking or flaming to occur during

cleaning ifthe oven is heavily soiled.

It is better to clean the oven regularly rather than to wait until

there is a heavy build-up of soil in the oven.

During the cleaning process, the kitchen should be well

ventilated to help eliminate normal odors associated with cleaning.

Do not use commercial even cleaners on the self-clean oven finish or around any part of the oven as they will dam-

age the finish or parts.

Before Self=Cleaning

Remove broiler pan, all pans and the oven racks from the

oven. The oven racks will discolor and may not slide easily after a self=clean cycle.

Clean oven frame, door frame ([areaoutside the door gaskeO and around the opening in the door gasket with a non-

abrasive cleaning agent such as Ben AmP or detergent and water. These areas are not exposed to cleaning temperatures

and should be cleaned to prevent soil from baking on during the clean cycle.

Select Light for a lightly soiled oven and two hours of

cleaning time. OR

Select Medium for medium soiled oven and three hours of

cleaning time. OR

Select Heavy for a heavily soiled oven and four hours of

cleaning time.

"Clean", the selected cleaning time and approximate unlocking time will be displayed while the oven is clean-

ing and cooling down.

Note: The door lock will disengage approximately one hour after the cleaning time is completed. The time of day

will appear in the display when the oven door has un-

locked.

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

CARE CLEANING

To Delay a Self=Clean Cycle:

1. PressClean pad. Clean

2. "Remove racks from oven" will be displayed. Remove the racks.

3. Select Continue.

4. Select Light for a lightly soiled oven and two hours of cleaning time.

OR Select Medium for medium soiled oven and three hours of

cleaning time. OR

Select Heavy for a heavily soiled oven and four hours of cleaning time.

5. The selected cleaning time and approximate unlocking time will be displayed.

6. After five seconds, Options will be displayed. Select Options.

7. Select Delay.

8. Selectthe number of hours you want to delay the start of the self-clean cycle.

9. The delay time and cleaning time will be displayed.

After Self=Cleaning

About one hour after the end of the clean cycle, the lock

will disengage and the time of day will appear in the

display. At this point the door can be opened.

Some soil may leave a light gray, powdery ash which can be

removed with a damp cloth. If soil remains, it indicates that

the clean cycle was not long enough. The soil will be removed during the next clean cycle.

If the oven racks were left inthe oven and do not slide smoothly after a clean cycle, wipe racks and embossed rack

supports with a small amount of vegetable oil to restore ease of movement.

A white discoloration may appear after cleaning if acidic or

sugary foods were not wiped up before the clean cycle. This is normal and will NOT affect performance.

Notes:

if the oven door is left open, "door" will flash in the display and a signal will beep until the door isclosed

and the Clean pad is pressed again. if more than 30 seconds elapse between pressing the

Clean pad and pressing a number pad, the program will automatically return to the previous display.

The oven door will be damaged ifthe oven door isforced to open during cleaning or cooling process.

The first few times the oven is cleaned, some smoke and odor may be detected. This is normal and will lessen or disappear with use. If the oven is heavily soiled, or ifthe

broiler pan was accidently left inthe oven, excessive smoke and odor may occur.

As the oven heats and cools, you may hear sounds of metal parts expanding and contracting. This isnormal

and will not damage your appliance.

CARE CLEANING

Cleaning Procedures

Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.

* Place soapy cloth over insert and pan; letsoak to loosensoil. . Wash in warm soapy water. Use scouring pad to remove stubborn soil. . Broiler pan and insert can be cleaned in dishwasher.

* Brandnames areregisteredtrademarksofthe

respectivemanufacturers,

** To order call 1-800-JENNAIR (1-800-536-6247).

Control Panel

Door Handle, Oven Exterior

(select models) =

Stainless Steel

Oven Window & Door = Glass

Oven Trim = Metal Finishes

. To activate "Control Lock" for cleaning, see page 6. . Wipe with damp cloth. Dry thoroughly.

* Glasscleaners may be used if sprayed on a cloth first. DO NOTspray directly on contrelpads and

display area.

* Do not use other cleaning sprays, abrasive cleaners or large amounts of water on the panel. . DO NOT USEANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.

* DO NOT USE "ORANGE" OR ABRASIVE CLEANERS.

* ALWAYS WIPE WITH THE GRAIN WHEN CLEANING. * Daily Cleaning/Light Soil -- Wipe with one of the following - soapywater, white vinegar/water

solution, Formula 409 Glassand Surface Cleaner* or a similar glasscleaner- using a sponge or soft cloth. Rinse and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray (Jenn- Air Model A912, Part No. 20000008:)**.

. Moderate/Heavy Soil =- Wipe with one of the following - Bon AmP, Smart Cleanser*, or Soft Scrub* -

using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp Scotch- Bfite* pad; rub evenly with the grain. Rinse and dry. To restore luster and remove streaks, follow with Stainless Steel Magic Spray.

. Avoid using excessive amounts of water which may seep under or behind glass causing staining. . Washwith soap and water. Rinse with clear water and dry. Glass cleaner can be used if sprayed on a

cloth first.

. Do not use abrasive materials such as scouring pads, steel wool or powdered cleaners as they will

scratch glass.

. Washwith soap and water, glass cleaners or mild liquid sprays.Avoid using excessive amounts of water. . Remove stubborn soils with nonabrasive cleaners such as Bon AmP or a baking soda and water paste;

rinse and dry. Do not use abrasive cleaners.

Oven interior

Oven Racks

See page 24for information on the self-clean oven.

To remove occasional spillovers between cleanings, use a plastic soap-filled scouring pad; rinse well.

Wipe up sugary spillovers and acidic spillovers such as lemonjuice, tomato sauce or milk-based sauces. Porcelain enamel isacid resistant, not acid proof. Theporcelain finish may discolor ifacidic orsugary spills are not wiped up prior to a self-clean cycle.

* Rub with a sponge or cloth using one of the following cleaners: Bon-Ami*, Soft Scrub* or Comet*. Rinse

and dry.

. For hard to remove soils, use a dampened soap-filled scouring pad. Rinse and dry. . Rackswill permanently discolor and may not slide smoothly if left in the oven during a self-clean

operation. If this occurs, wipe the rack and embossed rack supports with a small amount of vegetable oil to restore ease of movement, then wipe off excess oil.

A|NTENANCE

Oven Light

To assure the proper replacement bulb isused, order bulb from Jenn-Air. Call 1-800-JENNAIR 0-800-536-6247:), ask for part

number 74004458 - halogen bulb.

To Replace Oven Light Bulb:

1. Disconnect power to the wall oven.

2. When oven is cool, usefingertips to grasp edge of bulb cover.

Pull out and remove.

3. Carefully remove old bulb by pulling straight out of ceramic

base.

4. To avoid damaging or decreasing the life of the new bulb, do not touch the bulb with bare hands or fingers. Hold with a dry

cloth or paper towel. Push new bulb prongs straight into small holes of ceramic base.

5. Replace bulb cover by snapping into place.

6. Reconnect power to the oven. Reset clock.

OvenWindow

To protect the oven door window:

1. Do not use abrasive cleaning agents such as steel wool

scouring pads or powdered cleansers as they may scratch the glass.

2. Do not hit the glass with pots, pans, furniture, toys, or

other objects.

3. Do not close the oven door until the oven racks are in place.

Scratching, hitting, jarring or stressing the glass may weaken

its structure causing an increased risk of breakage at a later date.

TROUBLESHOOTING

For most concerns, try these first.

Clock, indicator words, and/or lights operate but oven does

not heat.

Oven light and/or clock

does not function.

There is a strong odor or light smoke when oven is turned on.

Oven will not activate the

self=cleaning process.

. Check if oven controls have been properly set. . Check if oven is properly connected to electrical outlet.

. Check or re-set circuit breaker. Check or replace fuse. . Check power supply.

. Clock controls may be set for a Cook/Hold or Delay function. . The Oven Control Lockout may have been set. (See page 6.:)

. The light bulb is loose or defective. . The oven light does not work during self-cleaning process.

. Oven may be in Sabbath Mode. (See page 21.:)

. This is normal fora newwall ovenand will disappear after afew uses. Initiating aclean

cycle will "burn off" the smells more quickly. Turning on a ventilation fan will help remove the smoke and/or odor.

. Excessivefood soils on the oven bottom. Use a self-clean cycle.

. Oven may be set for a delay clean. . Oven may be set for Sabbath Mode. (See page 21.)

. Double wall ovens - only one oven cavity can be cleaned at one time.

Oven did not clean properly.

Foods do not broil properly.

Baked food is burned or too brown on top.

Foods bake unevenly.

Oven door will not unlock. . Oven may not have cooled to safe temperature after self-cleaning process.

. Oven may need longer cleaning time. . Excessivespills were not removed prior to self-cleaning process.

. Check rack position. (See page 11.) . Voltage into house may be low.

. Food may be positioned incorrectlyin oven. . Oven not preheated properly.

. The oven may be installedimproperly. . Check the oven rack with a level.

. Stagger pans, do not allow pans to touch each other or oven wall. . Check instructionsfor suggested placement of pans on oven rack.

. There may be too many pans on one rack. . Baking pans may be oversized.

cont.

+ 67 hidden pages