JENN-AIR JGR8895BDS, JGR8895BDS0 Dimension Guide

30" (76.2 cm) Double Oven Gas Range

PRODUCT MODEL NUMBER PRODUCT DIMENSIONS

CABINET OPENING DIMENSIONS

JGR8895BD

Gas supply: This range is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.

Provide a gas supply line of 3/4" (1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in insufficient gas supply. Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON®† tape. With LP gas, piping or tubing size can be 1/2" (1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials used in the system.

If local codes permit, a new CSA design-certified, 4 to 5 ft (122 to 152.4 cm) long, 1/2" (1.3 cm) or 3/4" (1.9 cm) I.D., flexible metal appliance connector may be used for connecting range to the gas supply line.

A 1/2" (1.3 cm) male pipe thread is needed for connection to the female pipe threads of the inlet to the appliance pressure regulator.

The supply line must be equipped with a manual shutoff valve. This valve should be located in the same room but external to the range.

Electrical: The range must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate.

A 120-volt, 60-Hz, AC-only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this range be provided. Do not use an extension cord.

†®TEFLON is a registered trademark of E.I. Du Pont Nemours and Company.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.

Ref. W10162494

10-16-08

*Drill on centerline 1¼" (3.1 cm) from rear wall for gas supply

line.

**Gas lines and electrical plugs must be installed within the

shaded area to ensure proper alignment of this oven with cabinets.

A. 18" (45.7 cm) upper cabinet to countertop B. 13" (33.0 cm) upper cabinet depth C. 30" (76.2 cm) min. opening width D. For minimum clearance to the top of the cooktop, see NOTE.

E. 30" (76.2 cm) min. opening width F. 3" (7.6 cm) min. clearance from both sides of the range to the side

wall or other combustible material. G. 3" (7.6 cm) distance from wall H. Cabinet door or hinges should not extend into the cutout.

I. Clearance for gas pressure regulator

9¼"

(23.5 cm)

8¼"

(21.0 cm)

10"

(25.4 cm)

(12.7 cm)

15" (38.1 cm)

gas line location

3½"

(8.9 cm)

(7.6 cm)

(2.5 cm)

1¼"*

(3.1 cm)

2¼"**

(5.7 cm)

3½"

(8.9 cm)

(7.6 cm)

Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.

Range may be installed with zero clearance to combustible construction at the rear and on the sides below the cooktop.

NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is protected by not less than 1/4" (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet.

*Range can be raised approximately 1" (2.5 cm) by adjusting

the leveling legs.

**Model/serial/rating plates may be rotated up from behind the

control panel for viewing from the front of the range.

***Excludes handle. Dimension given is from wall to front of oven

door and will vary based on electric outlet receptacle installation.

A. 35⁷⁄₈" (91.1 cm) cooktop height

(minimum) with leveling legs screwed all the way in*

B. Model/serial/rating plates

(located behind the control panel)**

C. 46³⁄₄" (118.7 cm) overall height

(minimum) with leveling legs screwed all the way in*

D. 28¹⁄₈ " (71.3 cm) depth with

handle E. 26⁵⁄₁₆" - 27¼" (66.8 - 69.2 cm)*** F. 2 9⁷⁄₈ " (75.9 cm) width

E***