Jenn-Air JED4536W User Manual
JENN-AIR® DETAILED PLANNING DIMENSIONS
A
A
B
J
E
I
B
1 of 4
36" Jx3™ ELEcTRIc RADIANT DOwNDRAfT cOOkTOP wITh ELEcTRONIc TOuch cONTROL
JED4536W – 351⁄2" x 183⁄8" x 221⁄8"
PRODucT DIMENSIONS
MODEL # JED4536W
in cm
TOp VIEW
Overall width
Euro-Style Stainless 35
A
B
Floating Glass 35
Overall depth
Euro-Style Stainless 22
B
Floating Glass 22 55.9
Width of recessed cooktop 34
C
Width of blower motor assembly 12
D
Height from blower motor to countertop 18
E
Height of recessed cooktop 3
F
Height from electrical housing to countertop 8
G
Height of cooking surface
A
C
H
F
H
Depth of recessed cooktop 21 53.4
I
Height from plenum to countertop 16
J
G
1
⁄2 90.0
3
⁄8 89.8
1
⁄8 56.2
3
⁄8 87.3
1
⁄2 31.8
3
⁄8 46.8
7
⁄8 10.0
5
⁄8
22.0
1
⁄4 0.6
7
⁄8 42.8
E
FRONT VIEW
SIDE VIEW
D
B
I
J
E
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JRC120014A 07/2012
JENN-AIR® DETAILED PLANNING DIMENSIONS
Side
Cabinet
J
K
E*
F
D
e
A
B
B
v
I**
H
v
G
C
2 of 4
36" Jx3™ ELEcTRIc RADIANT DOwNDRAfT cOOkTOP wITh ELEcTRONIc TOuch cONTROL
JED4536W – 351⁄2" x 183⁄8" x 221⁄8"
OPENING/cLEARANcE DIMENSIONS
A
E*
F
B
G
v
H
e
C
v
I**
C
FRONT VIEW
Side
Cabinet
J
K
SIDE VIEW TOp VIEW – CuTOuT
B
D
MODEL # JED4536W
in cm
Width of combustible area above
A
cooking surface (min.)
Width from cooktop to fixed wall
B
or other combustible material (min.)
Width to center of vent opening option
C
Width to outer edge of outlet
D
Height to bottom of uncovered wood or
E*
metal cabinet above cooking surface (min.)
Height to bottom of uncovered wood
F
or metal cabinet (min.)
Height to center of vent opening option
G
Height to top edge of outlet (min.)
H
Depth to center of vent opening option
I**
Depth of upper cabinet (recommended)
J
Depth from cutout to wall (min.)
K
Width of cutout
L
Depth of cutout
M
Depth from cutout to front of countertop
N
e
Recommended electrical access location
Recommended venting location –
v
see pages 3-4 for ducting information
* Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet
is covered by not less than
less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)
aluminum or 0.020" (0.5 mm) copper.
**Based on installation in a 24" (61.0 cm) base cabinet.
1
⁄4" (0.6 cm) flame retardant millboard covered with not
36 91.4
1
2
⁄2 6.4
3
⁄8 39.2
15
10 25.4
30 76.3
18 45.7
16 40.6
12 30.5
3
16
⁄4 42.4
13 33.0
1
⁄2 3.8
1
1
⁄2 87.6
34
1
⁄8 53.7
21
2 5.1
ELECTRICAL REQuIREMENTS
240 volt, 60 Hz, AC only, 40-amp fused, electrical circuit is required.
A dedicated circuit is recommended.
VENTING REQuIREMENTS
This cooktop must be exhausted outdoors unless using the duct-free filter
kit (JDA7000WX). Refer to kit instructions for further information.
LOCATION REQuIREMENTS
• To ensure cooktop base clearance, cabinet side walls need to be wider
than the cutout.
• A minimum clearance of 6" (15.2 cm) is recommended between the
side of the cooktop and side wall for maximum ventilation performance.
• A minimum clearance of 2" (5.1 cm) is recommended between the
blower motor and cabinet for proper cooling. A 6" (15.2 cm) clearance
is recommended for servicing access.
• An under counter built-in oven cannot be installed under this cooktop.
L
K
M
N
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JRC120014A 07/2012
Loading...