Jenn-Air JDRP436WP01, JDRP536WP01, JDRP548WP01 Installation Guide

JENN-AIR°

INSTALLATIONINSTRUCTIONS

30" (76.2 CM), 36" (91.4 CM) AND 48" (121.9 CM)

COMMERCIAL STYLEDUALFUELCONVECTION RANGES

. INSTRUCTIONSD'I_STALLATION

CUISINIERESA CONVECTION A DOUBLECOMBUSTIBLE

ETDETYPECOMMERCIAL DE 30" (76,2 CM),

36" (91,4 CM) ET48" (I 21,9 CM)

TableofContents/Tabledes mah_res

RANGE SAFETY .............................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 3

Tools and Parts............................................................................ 3

Location Requirements ................................................................ 4

Electrical Requirements - U.S.A. Only ......................................... 6

Electrical Requirements - Canada Only ....................................... 7

Gas Supply Requirements ........................................................... 7

INSTALLATION INSTRUCTIONS .................................................. 8

Unpack Range .............................................................................. 8

Install Optional Backguard ........................................................... 9

Install Anti-Tip Bracket ................................................................. 9

Electrical Connection - U.S.A. Only ........................................... 10

Make Gas Connection ................................................................ 12

Verify Anti-Tip Bracket Location ................................................ 12

Level Range ................................................................................ 12

Install Griddle .............................................................................. 13

Electronic Ignition System .......................................................... 13

Reinstall Kick Plate ..................................................................... 14

Complete Installation .................................................................. 15

GAS CONVERSIONS .................................................................... 15

LP Gas Conversion .................................................................... 15

Natural Gas Conversion ............................................................. 17

Strip Circuits ............................................................................... 19

Wiring Diagrams ......................................................................... 21

SI_CURITI_ DE LA CUISINII=RE .............................................. 23

EXIGENCES D'INSTALLATION .............................................. 24

Outils et pieces ...................................................................... 24

Exigences d'emplacement .................................................... 25

Specifications de I'installation electrique ............................. 27

Specifications de I'alimentation en gaz ................................ 27

INSTRUCTIONS D'INSTALLATION ....................................... 29

Deballage de la cuisiniere ..................................................... 29

Installation du dosseret facultatif .......................................... 29

Installation de la bride antibasculement ............................... 29

Raccordement au gaz ........................................................... 30

Verification de I'emplacement de la bride

antibasculement .................................................................... 31

Reglage de I'aplomb de la cuisiniere .................................... 31

Installation de la plaque a frire .............................................. 31

Systeme d'allumage electronique ......................................... 31

Reinstallation du garde-pieds ............................................... 33

Achever I'installation ............................................................. 33

CONVERSIONS POUR CNANGEMENT DE GAZ ................. 34

Conversion pour I'alimentation au propane .......................... 34

Conversion pour I'alimentation au gaz naturel ..................... 36

Schemas des circuits ............................................................ 37

Schemas de c&blage ............................................................. 39

iMPORTANT:

Save for local electrical inspector's use. Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT:

_,conserver pour consultation par I'inspecteur local des installations _lectriques. Installateur : Remettre les instructions d'installation au propri_taire. Propri6taire : Conserver les instructions d'installation pour r_f_rence ult_rieure.

W10349768A

RANGESAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death,

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance,

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier,

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA. For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

In the State of Massachusetts, the following installation instructions apply: [] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type. [] A flexible gas connector, when used, must not exceed 3 feet.

Tip Over Hazard

A child or adult can tip the range and be killed. Connect anti-tip bracket to wall behind range.

Reconnect the anti-tip bracket, if the range is moved. Failure to follow these instructions can result in death or serious burns to children and adults.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here. Tools needed

• Tape measure

• #2 Phillips screwdriver

• 1/8"x 41¼'' flat-blade screwdriver

• Level

• Drill

• Wrench or pliers

• Pipe wrench

• Adjustable wrench or 8/8"wrench

• 3/8"drive ratchet

• 1/8"drill bit

• 18/le"combination wrench

• 1/4",3/8",8/W'nut drivers

Parts supplied

Check that all parts are included.

• Anti-tip bracket kit

A. Anti-tip bracket

B. #8-18 x 111Phillips head screws (4)

NOTE: Anti-tip bracket must be securely mounted to subfloor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store. See "Install Anti-Tip Bracket"

section.

I"®TORX is a registered trademark of Saturn Fasteners, Inc.

• 3/ls" carbide tip masonry bit

• Marker or pencil

• Pipe-joint compound resistant to LP gas

• Noncorrosive leak-detection solution

• Tubing cutter

For LP/Natural Gas

Conversions

• T15 Torx®tscrewdriver

• 7/8"socket

• Adjustable wrench

• 1/2"deep-well socket

• 7 mm nut driver

• Masking tape

• Gas pressure regulator

• Burner grates

• Burner heads and caps

• Griddle drip tray (on griddle models)

• LP orifice package (W10221288)

• Conversion label (VV10221320) NOTE: The cooktop is manufactured for use with Natural gas.

To convert to LP gas, see the "Gas Conversions" section.

Parts needed

• Power supply cord kit:

• 30" (76.2 cm) and 36" (91.4 cm) models - A UL listed

40 amp power supply cord kit

• 48" (121.9 cm) models - A UL listed 50 amp power supply

cord kit marked for use with nominal 13/8'' (34.93 mm) diameter connection openings

• A UL listed strain relief

• UL listed wire connectors

All models must be installed with a backguard if installing at zero

clearance to a combustible backwall. See "Cabinet Dimensions" in the "Location Requirements" section for installation

requirements.

• 30" (76.2 cm) Adjustable Backguard

Order Part Number 8285148

• 36" (91.4 cm) Adjustable Backguard

Order Part Number 8284756

• 48" (121.9 cm) Adjustable Backguard

Order Part Number 8284755

• 9" (22.9 cm) Backguard for 30" (76.2 cm) Ranges

Order Part Number W10115773

• 9" (22.9 cm) Backguard for 36" (91.4 cm) Ranges

Order Part Number W10115776

• 9" (22.9 cm) Backguard for 48" (121.9 cm) Ranges

Order Part Number W10115777

• 22" (55.9 cm) Backsplash with Dual-Position Shelf for

30" (76.2 cm) Ranges Order Part Number W10285447

• 22" (55.9 cm) Backsplash with Dual-Position Shelf for

36" (91.4 cm) Ranges Order Part Number W10285448

• 22" (55.9 cm) Backsplash with Dual-Position Shelf for

48" (121.9 cm) Ranges Order Part Number W10285449

To order, see the "Assistance or Service" section of the Use and Care Guide.

Checklocalcodesandconsultgassupplier.Checkexistinggas supplyandelectricalsupply.See"ElectricalRequirements"and "GasSupplyRequirements"sections.

Itisrecommendedthatallelectricalconnectionsbemadebya licensed,qualifiedelectricalinstaller.

High Altitude Conversion

To convert the cooktop for elevations above 6,560 ft (1999.5 m), order a High Altitude Conversion Kit.

• Part Number W10237848 - LP high altitude

• Part Number W10160841 - Natural gas high altitude To order, see the "Assistance or Service" section of the Use and

Care Guide.

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

• It is the installer's responsibility to comply with installation clearances specified on the model/seria( rating plate. The model/serial rating plate is located under the console on the right-hand side.

• It is recommended that a 600 CFM or larger range hood be installed above the range.

• It is not recommended that a microwave hood combination be mounted above the range.

• Recessed installations must provide complete enclosure of the sides and rear of the range.

• To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond

the bottom of the cabinets.

• All openings in the wall or floor where range is to be installed must be sealed.

• Do not seal the range to the side cabinets.

• Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

• The anti-tip bracket must be installed. To install the anti-tip bracket shipped with the range, see "Install Anti-Tip Bracket"

section.

• Grounded electrical supply is required. See "Electrical Requirements" section.

• Proper gas supply connection must be available. See "Gas Supply Requirements" section.

• Contact a qualified floor covering installer to check that the floor covering can withstand at least 200°F (93°C). Use an insulated pad or _¼"(0.64 cm) plywood over carpet and under range if installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the current standards CAN/CSA-A240-1atest edition, or with local

codes. Mobile home installations require:

• When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards

listed above.

Product Dimensions

30" (76.2 cm) models

A. Optional backguard may be installed. B. 273/4" (70.5 cm) depth with control panel, see NOTE* C. 353/4'' (89.6 cm) cooktop height when setting on the wheels D. 30" (76.2 cm) width

E.Model/serial rating plate location

36" (91.4 cm) models

Cabinet Dimensions

A. Optional backguard may be installed.

B.271/8'' (68.9 cm) depth with control panel, see NOTE* C. 353/4" (90.2 cm) cooktop height when setting on the wheels D. 36" (91.4 cm) width

E.Model/serial rating plate location

48" (121.9 cm) models

Cabinet opening dimensions shown are for 25" (64 cm) countertop depth, 24" (61 cm) base cabinet depth and 36" (91.4 cm) countertop height. Dimensions must be met in

order to ensure a flush fit to backwall. IMPORTANT: If installing a range hood or hood liner above the

range, follow the range hood or hood liner installation instructions for dimensional clearances above the cooktop surface.

Gas

area

installation

area*

D E

A. Optional backguard may be installed.

B.271/8'' (68.9 cm) depth with control panel, see NOTE* C. 353/4" (90.2 cm) cooktop height when setting on the wheels D. 48" (121.9 cm) width

E.Model/serial rating plate location

*NOTE: When installed in a 24" (61.0 cm) base cabinet with

25" (63.5 cm) countertop; front of oven door protrudes

17/8"(4.8 cm) beyond 24" (61.0 cm) base cabinet.

A. 18" (45. 7 cm) upper cabinet to countertop B. 30" (76.2 cm) model: 30" (76.2 cm) min. upper cabinet width

36" (91.4 cm) model: 36" (91.4 cm) min. upper cabinet width

48" (121.9 cm) model: 48" (121.9 cm) min. upper cabinet width C. 13" (33 cm) max. upper cabinet depth D. For minimum clearance to top of range, see NOTE**. E. 30¼" (76.8 cm) on 30" (76.2 cm) models

36¼" (92.1 cm) on 36" (91.4 cm) models

48¼" (122.6 cm) on 48" (121.9 cm) models

F. 6" (15.2 cm) min. clearance from both sides of range to side

wall or other combustible material

G. 15" (38.1 cm) H. 22" (55.9 cm) on 30" (76.2 cm) models

28" (71.1 cm) on 36" (91.4 cm) models

40" (101.6 cm) on 48" (121.9 cm) models

I. 17/2'' (3.8 cm)

J. 3" (7.6 cm)

K. 5" (12. 7 cm)

L. 6" (15.2 cm) on 30" (76.2 cm) models

14" (35.5 cm) on 36" (91.4 cm) models

24" (61.0 cm) on 48" (121.9 cm) models

M. 107/2"(26. 7 cm)

N. 6" (15.2 cm) O. 6" (15.2 cm), see NOTE***

*NOTE: Receptacle must be rotated 90° for Canadian

installation.

**NOTE: Minimum Clearances

30" (76.2 cm) models: 30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an

uncovered wood or metal cabinet. 36" (91.4 cm) models: 42" (106.7 cm) minimum clearance

between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.

48"(121.9cm)models:42"(106.7cm)minimumclearance

betweenthetopofthecookingplatformandthebottomofan

uncoveredwoodormetalcabinet.

***NOTE:Ifbackwallisconstructedofacombustiblematerial

andabackguardisnotinstalled,a6"(15.2cm)minimum clearanceisrequiredforallmodels.

Ifcodespermitandaseparategroundwireisused,itis recommendedthataqualifiedelectricalinstallerdeterminethat thegroundpathandwiregaugeareinaccordancewithlocal

codes. Ifcodespermitandaseparategroundwireisused,itis

recommendedthataqualifiedelectriciandeterminethatthe groundpathisadequate.

Donotuseanextensioncord. Besurethattheelectricalconnectionandwiresizeareadequate

andinconformancewiththeNationalElectricalCode,ANSI/ NFPA70-latesteditionandalllocalcodesandordinances.

Acopyoftheabovecodestandardscanbeobtainedfrom: NationalFireProtectionAssociation

OneBatterymarchPark Quincy,MA02269.

WARNING:Improperconnectionoftheequipment-grounding conductorcanresultinariskofelectricshock.Checkwitha

qualifiedelectricianorservicetechnicianifyouareindoubtasto whethertheapplianceisproperlygrounded.Donotmodifythe powersupplycordplug.Ifitwillnotfittheoutlet,haveaproper outletinstalledbyaqualifiedelectrician.

A circuit breaker is recommended. Wire sizes and connections must conform with the rating of

the range. The Tech Sheet is located behind the kick plate in a clear

plastic bag.

If connecting to a 4-wire system:

This range is manufactured with the ground connected to the

cabinet. The ground must be revised so the green ground wire of the 4-wire power supply cord is connected to the cabinet. See

"Electrical Connection." Grounding through the neutral conductor is prohibited for new

branch-circuit installations (1996 NEC); mobile homes; and recreational vehicles, or an area where local codes prohibit grounding through the neutral conductor.

When a 4-wire receptacle of NEMA Type 14-50R is used, a matching UL listed, 4-wire, 250-volt, 40- or 50-amp, range power supply cord must be used. This cord contains 4 copper conductors with ring terminals or open-end spade terminals with upturned ends, terminating in a NEMA Type 14-50R plug on the supply end.

The fourth (grounding) conductor must be identified by a green or

green/yellow cover and the neutral conductor by a white cover. Cord should be Type SRD or SRDT with a UL listed strain relief and be at least 4 ft (1.22 m) long.

Electrical Connection To properly install your range, you must determine the type of

electrical connection you will be using and follow the instructions provided for it here.

• Range must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located under the console on the right-hand side. Refer to the figures in the

"Product Dimensions" section of the "Location Requirements" section.

• This range may be manufactured with a 4-wire power supply cord or may not include a power supply cord. If your range does not include a power supply cord, use a 4-wire power supply cord rated at 250 volts, 40 or 50 amps and investigated for use with ranges.

Range Rating* Specified Rating of Power

Supply Cord Kit and Circuit Protection

120/240 Volts 120/208 Volts Amps Range Size

8.8 - 16.5 kW 7.8 - 12.5 kW 40 or 50"* 30" (76.2 cm), 36" (91.4 cm)

16.6 - 22.5 kW 12.6 - 18.5 kW 50 48" (121.9 cm)

*The NEC calculated load is less than the total connected load

listed on the model/serial rating plate.

**If connecting to a 50-amp circuit, use a 50-amp rated cord with

kit. For 50-amp rated cord kits, use kits that specify use with a

nominal 13/8"(34.9 mm) diameter connection opening.

4-wire receptacle (14-50R)

The minimum conductor sized for the copper 4-wire power

cord are: 40-amp circuit

2 No.-8 conductors 1 No.-10 white neutral

1 No.-8 green grounding

If connecting to a 3-wire system:

Local codes may permit the use of a UL listed, 3-wire, 250-volt, 40- or 50-amp range power supply cord (pigtail). This cord contains 3 copper conductors with ring terminals or open-end spade terminals with upturned ends, terminating in a NEMA Type 10-50P plug on the supply end. Connectors on the appliance end must be provided at the point the power supply cord enters the appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.

3-wire receptacle (10-50R)

E ¸ _ _:_,_,_

Electrical Shock Hazard

Electrically ground range. Failure to do so can result in death, fire, or

electrical shock.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local

codes. Be sure that the electrical connection and wire size are adequate

and in conformance with the CSA Standard C22.1, Canadian Electrical Code, Part 1 - latest edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from: Canadian Standards Association

178 Rexdale Blvd. Toronto, ON M9W 1R3 CANADA

• Check with a qualified electrical installer if you are not sure the range is properly grounded.

• When a 4-wire, single phase 250 volt, 60 Hz., AC only electrical supply is available, a 40-amp minimum circuit protection is required on 30" (76.2 cm) and 36" (91.4 cm) ranges and a 50-amp minimum circuit protections is required on 48" (121.9 cm) ranges, fused on both sides of the line.

• A time-delay fuse or circuit breaker is recommended.

• This range is equipped with a CSA International Certified Power Cord intended to be plugged into a standard 14-50R wall receptacle. Be sure the wall receptacle is within reach of range's final location.

• Do not use an extension cord.

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections. if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances. IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition or CAN/CGA B149 - latest edition.

IMPORTANT: Range cooktop must be connected to a regulated gas supply.

IMPORTANT: Leak testing of the range cooktop must be conducted according to the manufacturer's instructions.

Type of Gas

Natural Gas:

This range is design-certified by CSA International for use with

Natural gas or, after proper conversion, for use with LP gas.

• This range is factory set for use with Natural gas. The model/ serial rating plate located under the console on the right-hand side has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP Gas conversion:

Conversion must be done by a qualified service technician. No attempt shall be made to convert the range cooktop from the

gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. To convert to LP gas, use the LP gas conversion kit provided with

your range and see the "Gas Conversions" section. The parts for

this kit are in the literature package supplied with the range.

Gas Supply Line

• Provide a gas supply line of 3A"(1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in insufficient gas supply. With LP gas, piping or tubing size can be 1/2"(1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials used in the system.

NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON ®ttape.

Flexible metal appliance connector:

• If local codes permit, a new CSA design-certified,

4 - 5 ft (122 - 152.4 cm) long, 5/8"(1.6 cm) or 3A"(1.9 cm) I.D., flexible metal appliance connector may be used for connecting range to the gas supply line.

• A 1/2"(1.3 cm) male pipe thread is needed for connection

to the female pipe threads of the inlet to the range pressure regulator.

• Do not kink or damage the flexible metal tubing when

moving the range.

Rigid pipe connection: The rigid pipe connection requires a combination of pipe

fittings to obtain an in-line connection to the range. The rigid pipe must be level with the range connection. All strains must be removed from the supply and fuel lines so range will be

level and in line.

LP Gas: Minimum pressure: 11" (27.9 cm) WCP

Maximum pressure: 14" (35.6 cm)WCP Contact local gas supplier if you are not sure about the inlet

pressure.

Burner Input Rating - Altitude

Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings need to be reduced at a rate of 4% for each 1,000 ft (304.8 m).

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least 1" water column pressure above the manifold pressure shown on the model/serial rating plate.

Line pressure testing above 1/2psi gauge (14" WCP)

The range and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2psi (3.5 kPa).

Line pressure testing at 1/2psi gauge (14" WCP) or lower

The range must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2psi (3.5 kPa).

INSTALLATIONINSTRUCTIONS

Must include a manual shutoff valve: The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but external to the range opening, such as an adjacent cabinet. It

should be in a location that allows ease of opening and closing. Do not block access to shutoff valve. The valve is for turning on or shutting off gas to the range.

A. Gas supply line B. Shutoff valve "open" position C. To range

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be used. The inlet pressure to the regulator should be as follows for

proper operation: Natural Gas:

Minimum pressure: 6" (15.2 cm) WCP Maximum pressure: 14" (35.6 cm)WCP

Excessive Weight Hazard

Use two or more people to move and install range. Failure to do so can result in back or other injury.

1. Remove shipping materials, tape and film from range. Keep shipping pallet under range. Remove oven racks, grates and parts package from inside oven.

2. Remove screws from kick plate.

A. Kick plate B. Remove these screws.

3. Push up on kick plate to release plate from shoulder screws.

4. Lay kick plate to the side to avoid scratching the stainless steel.

t®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

For 48" (121.9 cm) models only, rotate center support counterclockwise off the pallet until it stops.

NOTE: This support is used only for shipping and is not

needed for installation.

Lay a piece of cardboard from side packing on the floor behind range. Using 2 or more people, firmly grasp each side of range. Lift range up about 3" (8.0 cm) and move it back until range is off shipping pallet. Set range on cardboard to avoid damaging floor.

All ranges may require a backguard. See "Cabinet Dimensions" in the "Location Requirements" section. See the "Tools and Parts" section for information on ordering.

Remove island trim and attach backguard using 6 screws, insert 3 from the front and 3 from the back (9" [22.9 cm] backguard shown).

If you have a stone or masonry floor, you can use the wall mounting method.

Determine and mark centerline of the cutout space. The mounting bracket must be installed on the right side of the cutout. Position mounting bracket in cutout as shown in the following illustration.

Measurement B:

30" (76.2 cm) ranges: 11%" (29.5 cm) 36" (91.4 cm) ranges: 14%" (37.1 cm) 48" (121.9 cm) ranges: 205/8'' (52.4 cm)

Measurement C:

Optional distance from backwall. If backwall is constructed of a combustible material and a backguard is not installed, a 6" (15.2 cm) minimum clearance is required for all models. Install anti-tip bracket accordingly.

A. Centerline

B. Centerline of cutout to centerline

of anti-tip bracket

C. Backwall to back of range

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti=tip bracket to rear range foot. Reconnect the anti=tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

3. Drill two V8" (3.0 mm) holes that correspond to the bracket holes of the determined mounting method. See the following.

Floor Mounting

A. #12 x 1%" screws

B.Anti-tip bracket

1. Determine which mounting method to use: floor or wall.

Wall Mounting 4. Using a Phillips screwdriver, mount anti-tip bracket to the wall

or floor with the two #12 x 15/8'' screws provided. Depending on the thickness of your flooring, longer screws

may be necessary to anchor the bracket to the subfloor. Longer screws are available from your local hardware store.

5. Move range close enough to opening to allow for electrical connections to be made. Remove shipping base, cardboard or hardboard from under range.

6. Continue installing your range using the following installation instructions.

A. #12 x 1%" screws B. Anti-tip bracket

30" (76.2 cm) and 36" (91.4 cm) Models

Electrical Shock Hazard

Disconnect power before servicing. Use a new 40 amp power supply cord.

Plug into a grounded outlet. Failure to follow these instructions can result in death,

fire, or electrical shock.

Disconnect power.

Remove the terminal block cover screws and disengage mounting tabs to remove terminal block cover from back of

range.

48" (121.9 cm) Models

Electrical Shock Hazard

Disconnect power before servicing. Use a new 50 amp power supply cord.

Plug into a grounded outlet. Failure to follow these instructions can result in death,

fire, or electrical shock.

• Assemble a UL listed strain relief in the opening.

A. Phillips head screws B. Terminal block cover

C. Two mounting tabs at bottom

Add power supply cord strain relief.

A.UL listed strainrelief

Tighten strain relief screw against the power supply cord.

4. Complete installation following instructions for your type of electrical connection:

4-wire (recommended) 3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has: And you will be Go to Section:

connecting to:

4-wire receptacle (NEMA type 14-50R)

A UL listed,

250-volt

4-wire connection:

Power supply cord minimum, 40- or 50-amp,

range power supply cord

Connect the neutral (center) wire to the center terminal connector using one of the hex washer head screws. Securely tighten screw for proper electrical connection.

J G

3-wire receptacle (NEMA type 10-50R)

A UL listed,

250-volt

3-wire connection:

Power supply cord minimum, 40- or 50-amp,

range power supply cord

4-wire connection: Power supply cord

Use this method for:

• New branch-circuit installations (1996 NEC)

• Mobile homes

• Recreational vehicles

• In an area where local codes prohibit grounding through the neutral

Remove the ground-link screw from the range frame. Save the ground-link screw. Bend the ground link away from the

range so that it does not contact the range.

A. Line 1

B. Green ground wire

C. Ground-link screw D. Hex washer head screw

E. Silver-colored terminal

block screw

F. Ground link

G. Neutral (center) wire H. Line 2

I. UL listed strain relief and

40- or 50-amp range

power supply cord

5. Connect the other 2 wires (lines 1 and 2) to the outer aluminum terminal blocks.

6. Securely tighten screws for proper electrical connection.

7. Tighten strain relief screws.

8. Replace terminal block cover.

3-wire connection: Power supply cord

Use this method only if local codes permit connecting cabinet- ground conductor to neutral wire of power supply cord.

1. Use a 1¼,,nut driver and remove the hex washer head screws from the aluminum terminal blocks.

2. Connect the neutral (center) wire to the center terminal connector using one of the hex washer head screws. Securely tighten screw for proper electrical connection.

A. Ground-link screw

B. Ground link bent away from range

2. Connect the green ground wire from the power supply cord to the range using the ground-link screw. The ground wire must be attached first and must not contact any other terminal.

3. Use a %" nut driver to remove the hex washer head screws from the terminal blocks.

A. Line 1 B. Ground link C. Hex washer head screw D. Silver-colored terminal

block screw

E. Neutral (center) wire F. Line 2

G. UL listed strain relief

and 40- or 50-amp range power supply cord

3. Connect the other 2 wires (lines 1 and 2) to the outer terminal screws on the terminal block.

4. Tighten strain relief screws.

5. Replace terminal block cover.

Explosion Hazard

Use a new CSA International approved gas supply line. install a shut=off valve.

Securely tighten all gas connections. if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

1. Assemble flexible connector from gas supply pipe to pressure regulator located in the middle rear of the range.

2. Apply pipe-joint compound made for use with LP gas to the smaller thread ends of the flexible connector adapters (see B and G in the following illustration).

3. Attach one adapter to the gas pressure regulator and the other adapter to the gas shutoff valve. Tighten both adapters.

4. Use a 15/le"combination wrench and channel lock pliers to attach the flexible connector to the adapters. Check that

connector is not kinked.

2. Test all connections by brushing on an approved noncorrosive leak-detection solution. If bubbles appear, a leak is indicated. Correct any leak found.

3. Remove cooktop burner caps and grates from parts package. Place burner caps on burner bases. Place burner grates over burners and caps.

4. Check that the range is plugged into the appropriate outlet (see the "Electrical Requirements" section).

5. Turn on power supply. For further information, please refer to the user instructions located in the Use and Care Guide.

Turn all 4 leveling rods 1 full turn to raise the range and provide enough clearance for the rear leveling leg to slide into the anti-tip bracket.

2. Move range into its final location making sure rear leveling leg slides into anti-tip bracket.

NOTE: If installing the range in a mobile home, you must secure the range to the floor. Any method of securing the range is adequate as long as it conforms to the standards in the "Location Requirements" section.

NOTE: Range must be level for satisfactory baking performance.

1. Place rack in oven.

2. Place level on rack and check levelness of the range, first side to side; then front to back.

A B C

H G F

A. Gas pressure regulator B. Use pipe-joint compound.

C. Adapter (must have Y2"male

pipe thread)

D. Flexible connector

E.Manual gas shutoff valve F Y2"or 3/4"gas pipe

G. Use pipe-joint compound. H. Adapter

Complete Connection

1. Open the manual shutoff valve in the gas supply line. The valve is open when the handle is parallel to the gas pipe.

A. Closed valve B. Open valve

3. If range is not level, adjust the leveling rods. Turn leveling rods located behind the kickplate to level range and to raise or lower range to the desired countertop height.

NOTE: All roller feet must be off the floor upon final installation.

A. Front leveling rod B. Rear leveling rod

+ 28 hidden pages