JBL EON-1-PRO-DMS300-V-K, EON-1-PRO-DMS300-I-K, EON-1-PRO-DMS100-V-K, EON-1-PRO-DMS100-I-K User's Guide

Page 1
USER’S GUIDE
For: Français, Deutsch, Español, visit www.jblpro.com
Page 2
Section 1: Important Safety Instructions ���������������������������������������������������������� 1
Care & Cleaning �������������������������������������������������������������������������������������������������������������������������������������������������� 2
Section 2: Precautions ���������������������������������������������������������������������������������������� 3
Section 3: EON ONE PRO System Declaration of Conformity ������������������������ 4
Section 4: Introduction to the EON ONE PRO System ������������������������������������ 5
Getting Started ���������������������������������������������������������������������������������������������������������������������������������������������������� 5
PA Basics ������������������������������������������������������������������������������������������������������������������������������������������������������������8
Getting Acquainted with the EON ONE PRO Powered Mixer �����������������������������������������������������������������������������8
Audio Inputs �������������������������������������������������������������������������������������������������������������������������������������������������������� 9
Mono Mic/Line Inputs ������������������������������������������������������������������������������������������������������������������������������������� 9
Phantom Power Disclaimer �������������������������������������������������������������������������������������������������������������������������� 10
Stereo Inputs ������������������������������������������������������������������������������������������������������������������������������������������������ 11
Bluetooth Input ��������������������������������������������������������������������������������������������������������������������������������������������� 11
Audio Outputs ���������������������������������������������������������������������������������������������������������������������������������������������������12
USB Power Port ������������������������������������������������������������������������������������������������������������������������������������������������ 12
Section 5: Accessories ������������������������������������������������������������������������������������� 13
Accessory Mount ����������������������������������������������������������������������������������������������������������������������������������������������13
Wheeled Bag ����������������������������������������������������������������������������������������������������������������������������������������������������13
Section 6: System Specications �������������������������������������������������������������������� 14
Section 7: Cables & Connectors ���������������������������������������������������������������������� 15
Section 8: Contact Information ������������������������������������������������������������������������ 16
Section 9: Warranty Information ���������������������������������������������������������������������� 17
Page 3
Section 1: Important Safety Instructions
1� Read these instructions�
2� Keep these instructions�
3� Heed all warnings�
4� Follow all instructions�
5� Do not use this apparatus near water�
6� Clean only with dry cloth�
7� Do not block any ventilation openings� Install in accordance with the manufacturer’s instructions�
8� Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9� Do not defeat the safety purpose of the polarized or grounding-type plug� A polarized plug has two blades with one
wider than the other� A grounding-type plug has two blades and a third grounding prong� The wide blade or the
third prong is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet�
10� Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus�
11� Only use attachments/accessories specied by the manufacturer.
12�
13� Unplug this apparatus during lightning storms or when unused for long periods of time�
14� Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped�
15� Service Instruction in Owner’s Manual: “CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY� TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO�”
16� To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug from the AC
receptacle�
17� “WARNING – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE�”
18� Do not expose this equipment to dripping or splashing and ensure that no objects lled with liquids, such as vases,
are placed on the equipment�
19� WARNING: The mains plug/appliance coupler is used as disconnect device, the disconnect device shall remain
readily operable�
20�
21�
22� No naked ame sources, such as lighted candles, should be placed on the apparatus.
23� For adequate ventilation, do not install this equipment in a conned or enclosed space, such as a book case or
similar unit� Product ventilation should not be impeded by covering the ventilation openings with items such as newspaper, tablecloths, curtains, etcetera�
Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the
apparatus� When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over�
Protective earthing terminal� The apparatus should be connected to a mains socket outlet with a protective earthing connection�
Correct Disposal of this product� This marking indicates that this product should not be disposed with other household wastes throughout the EU� To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources� To return your used device, please use the return and collection systems or contact the retailer where the product was purchased� They can take this product for environmental safe recycling�
1
Page 4
CARE & CLEANING
EON ONE PRO systems may be cleaned with a dry cloth� Do not get moisture into any of the openings in the system� Ensure that the system is unplugged from the AC outlet before cleaning�
THIS APPARATUS CONTAINS POTENTIALLY LETHAL VOLTAGES� TO PREVENT ELECTRIC SHOCK OR HAZARD, DO NOT REMOVE CHASSIS, MIXER MODULE, OR AC INPUT COVERS� NO USER SERVICEABLE PARTS INSIDE� REFER SERVICING TO QUALIFIED SERVICE PERSONNEL�
2
Page 5
Section 2: Precautions
The EON ONE PRO system covered by this manual is not intended for use in high moisture environments� Moisture can damage the speaker cone and surround and cause corrosion of electrical contacts and metal parts� Avoid exposing the speakers to direct moisture� Keep speakers out of extended or intense direct sunlight� The
driver suspension will prematurely dry out and nished surfaces may be degraded
!
Hearing Damage, Prolonged Exposure To Excessive SPL
The EON ONE PRO system is capable of generating sound pressure levels (SPL) sufcient to cause permanent hearing damage to performers, production crew, and audience members� Caution should be taken to avoid prolonged exposure to SPL in excess of 90 dB�
WATCH FOR THESE SYMBOLS!
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product�
by long-term exposure to intense ultra-violet (UV) light. The EON ONE PRO system can generate considerable energy� When placed on a slippery surface such as polished wood or linoleum, the speaker may move due to its acoustical energy output� Precautions should be taken to assure that the speaker does not fall off a stage or table on which it is placed�
The lightning ash with the arrowhead symbol within an
equilateral triangle is intended to alert the user to the presence of un-insulated “Dangerous Voltage” within the products
enclosure that may be of sufcient magnitude to constitute a risk
of electric shock to persons�
WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE�
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
3
Page 6
Section 3: EON ONE PRO System Declaration of Conformity
This equipment complies with the EMC directive 89/336/EEC Modied by 92/31/EEC 93/68/EEC
98/13/EEC and LVD 73/23/EEC modied by 93/68/EEC
This product meets safety standards: EN60065:2002 UL6500 7th Edition: 2003 UL 60065 - STANDARD FOR AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY EQUIREMENTS - Edition 7 - Revision Date 2007/12/11 CSA C22�2 NO 60065-03 - AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS – SAFETY REQUIREMENTS - Edition 1 - Revision Date 2006/04/01 IEC 60065 - AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS -- SAFETY REQUIREMENTS - Edition 7�1 - Issue Date 2005/12/01
And EMC Standards
EN55103-1 (E2) EN55103-2 (E2)
This device complies with Industry Canada’s licence-exempt RSSs� Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence� L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement�
Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment�
FCC Compliance Notice
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation�
CAUTION: Changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment�
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part of the FCC Rules� These limits are designed to provide reasonable protection against harmful interference in a residential installation� This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications� However there is no guarantee that the interference will not occur in a particular installation� If this equipment does cause harmful interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to collect the interference by one or more of the following measures�
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
• FCC RADIATION EXPOSURE STATEMENT
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment� This device should be installed and operated with minimum distance 20cm between the radiator & your body�
4
Page 7
Section 4: Introduction to the EON ONE PRO System
Thank you for choosing the JBL EON ONE PRO system� The EON ONE PRO is a portable all-in-one linear-array system featuring rechargeable battery power, multiple input channels with individual tone controls, reverb, and Bluetooth® audio streaming� With a design that stores all the components into one lightweight unit for one-hand carry, the EON ONE PRO provides a versatile PA system that is perfect for situations where ease and portability are just as important as legendary JBL sound�
The following items are included in the EON ONE PRO package:
• 1 JBL EON ONE PRO base
• 2 listening height spacers
• 1 column speaker array
• 1 power cable
• Quick start guide
GETTING STARTED
1� Remove the EON ONE PRO system from the carton�
2� Push the latch lever and lift the cover, then remove the spacers and column speaker array from the back of
the unit�
3� Place spacers for the desired listening level, then attach the column speaker array�
Speaker Array
Speaker Array
Speaker Array
Speaker Array Only 1 Spacer 2 Spacers
Spacer
SpacerSpacer
5
Page 8
4� Connect the female end of the power cable to the EON ONE PRO and plug the male end into a wall socket�
Ensure the Power switch is turned off and the power LED is not lit. If using the unit's battery power feature, allow the unit to charge� The Battery Level meter will illuminate, indicating the unit is charging� The lithium­ion battery will take approximately 5 hours to fully charge, and the Battery Level meter will fully illuminate to indicate charging is complete�
AC Power Receptacle
& Power Switch
5� Turn the MASTER VOLUME and CHANNEL VOLUME controls all the way to the left�
Master Volume
Channel Volumes
6� Make audio connections� Set the MIC/LINE buttons for the type of connections being made to each mono
channel (XLR = mic, 1/4" phone = line). If connecting instruments with pickups, connect them to inputs 3
and 4 and enable the CH3+CH4 HI-Z button. If using condenser mics, rst connect them to inputs 1 and/or 2� Then enable the CH1+CH2 PHANTOM button� See "Phantom Power Disclaimer" on page 10 for important information about using phantom power�
Mic/Line Buttons
Phantom Power and Hi-Z Buttons
Audio Connectors
6
Page 9
7� Turn the POWER switch to the “on” position� The POWER LED indicators on the front and back of the unit
will illuminate to indicate power is turned on�
Power Switch
8� If connecting a Bluetooth device for audio streaming, follow these steps:
a� Enable Bluetooth on your source device�
b� Press the BLUETOOTH button�
c� Find JBL EON ONE PRO on your device and select it�
d� If applicable, connect the device to the USB POWER port to keep it charged�
Bluetooth Button
9� Set the Channel Volume controls to 12 o’clock�
10� Slowly turn the Master Volume control to the right until the desired volume is reached�
11� Fine tune the Channel Volume controls for the desired mix balance� If using Bluetooth audio streaming,
adjust the Bluetooth streaming device's volume control to balance it with the other channels.
12� Add the nishing touches by adjusting the tone of each channel using the TREBLE and BASS controls�
Enable and adjust the REVERB controls for any channels, such as vocals, which could use reverb�
13� Enjoy your audio!
7
Page 10
PA BASICS
A mixing board is actually a very simple device that takes the audio input signals (from the input channels) and
"mixes" them to the outputs� The mixing board controls will typically enable the user to blend the input channel
signal levels, affect their tone, and adjust each channel's reverb level. The signal is then fed from the mixing board to the ampliers and on to the speakers. The EON ONE PRO is a self-contained PA system, which includes a mixing board, ampliers, and speakers.
GETTING ACQUAINTED WITH THE EON ONE PRO POWERED MIXER
The powered mixer section of the EON ONE PRO system houses the mixing board and power amplier. Here,
all of the microphones, musical instruments, and external sound sources (such as MP3 players, CD players, or
Bluetooth audio sources) can be connected.
The MONITOR OUT RCA jacks provide a “Front-of-House” feed, which can be connected to recording devices or
additional speakers (such as a powered personal monitor or another PA system). The PASS THRU output can be
used to connect multiple EON ONE PRO line arrays together for increased sound output�
Let’s take a look at the audio input channels rst.
8
Page 11
AUDIO INPUTS
The EON ONE PRO has 7 inputs: 4 mono inputs, a 2-channel (stereo) input, and a Bluetooth audio streaming
input� All of the inputs will route to the speakers, the MONITOR OUT jack, and the PASS THRU out jack�
MONO MIC/LINE INPUTS
Moving from left to right there are four identical input strips comprised of (from top to bottom) a treble control, bass
control, reverb control, reverb on/off button, mic/line selector, volume control, and a XLR / 1/4" combination input connector� On the right, there is a phantom power enable button for channels 1 and 2 and a hi-z button for inputs 3 and 4�
Treble control adjusts the amount of high frequencies on each channel
Bass control adjusts the amount of low frequencies on each channel
Reverb control adjusts the amount of reverb applied to each channel
Reverb On/Off button enables the reverb for each channel
Mic/Line button selects between a microphone
(XLR) input or a line (1/4" phone) input
Channel Volume controls adjust the gain for each channel
Ch1+Ch2 Phantom button enables +48V phantom power on channels 1 and 2 for powering condenser microphones (see "Phantom Power
Disclaimer" on page
10)
Ch3+Ch4 Hi-Z button enables high-impedance operation on channel 3
and 4 (1/4" phone inputs)
for direct connection of instruments with pickups
Combination 1/4" phone
(line) and XLR female (mic)
input connectors
9
Page 12
PHANTOM POWER DISCLAIMER
When using condenser microphones, +48V phantom power is required to be present at the contacts of the
microphone (XLR) connector for the microphone to operate correctly. When phantom power is enabled, it is
applied to both the CH1 and CH2 XLR inputs� Ensure that phantom power is off when not required�
To prevent damage to the EON ONE PRO or external devices when using condenser microphones, always turn down all EON ONE PRO output controls and ensure the +48V phantom power is off before connecting the microphone� Once the condenser microphone has been connected, enable the +48V phantom power, then raise the output controls to the desired levels�
WARNING! Do not connect any unbalanced sources to the XLR inputs when +48V phantom power is enabled� Doing so may damage the connected device due to the phantom power voltage on pins 2 and 3 of the XLR connector�
10
Page 13
STEREO INPUTS
The CH 5/6 stereo inputs are intended to be used primarily for MP3 or other personal music players and offer the
option of using RCA plugs or a 3.5 mm stereo connector plug (the type typically found on personal music players).
The CH 5/6 control is used to control volume for this stereo input�
Volume control for the CH 5/6 stereo input
Stereo in 5/6 RCA inputs for use with personal music player or any consumer-type electronics
CH 5/6 3�5 mm stereo input connector for use with personal music players
BLUETOOTH INPUT
The EON ONE PRO comes equipped with the ability to stream Bluetooth audio for music playback or backing
tracks. To connect a Bluetooth device, rst press the BLUETOOTH PAIR button on the back of the EON ONE
PRO� Then select "EON ONE PRO" from the source device to complete the pairing� The level of the Bluetooth device relative to other source channels can be controlled from the Bluetooth device�
Push Bluetooth button to pair with Bluetooth device
11
Page 14
AUDIO OUTPUTS
Monitor Out connectors with volume control are used to route the stereo mixer signal to another destination, such as a recording device, powered personal monitor, or another PA system
USB POWER PORT
This port can be used to charge a Bluetooth device or other portable music playback device during use�
PASS THRU output can be connected to the XLR input of another JBL EON ONE PRO to expand the system for higher output capabilities
12
Page 15
Section 5: Accessories
ACCESSORY MOUNT
The optional accessory mount can be mounted to the hole located at the top of the line-array speaker� Simply attach a GoPro® camera and you’re ready to record� Or connect a lighting element to set the perfect vibe� Visit jblpro�com or contact your local JBL Pro dealer for more information�
WHEELED BAG
The optional wheeled bag is available for effortless transport of an EON ONE PRO system� Visit jblpro�com or contact your local JBL Pro dealer for more information�
13
Page 16
Section 6: System Specications
System
Battery
Amplier
Mixer
Speaker
System Type: Battery-operated portable line array with powered mixer
Maximum SPL Output: 118 dB peak system output (pink noise)
Frequency Range (-10dB): 37�5Hz – 18�5kHz
Frequency Response (-3dB): 45Hz – 18kHz
AC input : 100 – 120 VAC, 50/60Hz; 220 – 240 VAC, 50/60Hz
USB Power Port: Supplies 500mA
Type: Extended-life lithium-ion
Charge Time: 5 hours
Run Time: Up to 6 hours
Design: Class D
System Power Rating: 250W LF/HF
Input Connectors: 6 inputs (4 x mono mic/line, 1 x stereo)
Channels: 1-4: XLR / 1/4" combo connectors (XLR = mic-level input, 1/4" = line-level input)
Input Impedance: Ch 1-4 combo XLR: 40 K Ohms balanced
Phantom Power: 48V (CH1-4 XLR inputs)
Bluetooth: 2-channel Bluetooth audio input streaming (stereo signal is fed to the MONITOR OUT
Output Connectors: 3 outputs (1 x stereo RCA monitor output, 1 x mono pass thru output)
Output Impedance: RCA monitor outputs: 100 Ohms unbalanced
Signal Indicators: Limit: Yellow LED indicates limiter active condition
EQ: Individual channel Bass and Treble controls, center detent, +/-12 dB cut and boost
System Limiter: On-board DSP limiting and tuning
LF Driver: 1 x 8" (203.2mm) woofer
HF Driver: 6 x 2" (50.8mm) drivers
Coverage Pattern: 80º x 60º (H x V)
Enclosure: Polypropylene
Grille: Powder-coated perforated steel
Dimensions (D x W x H)
Unit Dimensions: Packaged Dimensions:
Net Weight of System: 37.5 lbs (17.0 kg)
(Enabling the CH3+CH4 HI-Z button switches 1/4" inputs on channels 3-4 to accept high-
impedance signals from instruments.)
5-6: 3�5 mm stereo jack or stereo RCA connectors
Ch 1-2 combo TRS: 40 K Ohms balanced
Ch 3-4 combo TRS (CH3+CH4 HI-Z button disabled): 40 K Ohms balanced
Ch 3-4 combo TRS (CH3+CH4 HI-Z button enabled): 40 K Ohms unbalanced
Ch 5-6 RCA: 5 K Ohms unbalanced
Ch 5-6 3�5 mm: 10 K Ohms unbalanced
jacks while mono-summed signal is fed to the line array speakers)
XLR pass thru output: 37 Ohms balanced
15.8" x 10.5" x 23.4" (401mm x 266mm x 594mm)
16.6" x 21.3" x 30.4" (421mm x 541mm x 772mm)
14
Page 17
Section 7: Cables & Connectors
XLR/F to XLR/M microphone cable
The standard cable for interconnection of microphone and line­level signals in professional audio systems� Example: Microphone to mixer�
TRS (balanced) 1/4" phone to XLR/M cable
TRS (unbalanced) 1/4" phone to XLR/M cable
TS (unbalanced) 1/4" phone to XLR/M cable
XLR/M to RCA (phono) cable
TS (unbalanced) 1/4" phone to RCA (phono) cable Connects an unbalanced 1/4" output to an RCA input�
TRS 1/4" phone to dual 1/4" phone cable
XLR/F to XLR/M audio ground lift adapter
For connecting balanced devices with 1/4" phone; may be
used interchangeably�
For connecting instruments with unbalanced outputs to balanced XLR inputs�
This cable is electrically identical to “TRS” (unbalanced) 1/4" phone and may be used interchangeably�
Connects consumer audio products and some DJ mixer outputs to professional audio equipment inputs�
Splits a stereo output into separate left/right signals� Also used for connecting signal processors to mixer insert jacks�
Used for breaking ground loops between interconnected devices — works with balanced inputs and outputs only�
XLT/F to XLR/M Audio Groud Lift
(no connection)
15
Page 18
Section 8: Contact Information
Mailing Address:
JBL Professional 8500 Balboa Blvd� Northridge, CA 91329
Shipping Address:
JBL Professional 8500 Balboa Blvd�, Dock 15 Northridge, CA 91329 (Do not return product to this address without rst obtaining prior authorization from JBL)
Customer Service:
Monday through Friday 8:00am - 5:00pm
Pacic Coast Time in the U.S.A. (800) 8JBLPRO (800.852.5776)
www�jblproservice�com
On The World Wide Web:
www�jblpro�com
Professional Contacts, Outside the USA:
Contact the JBL Professional Distributor in your area� A complete list of JBL Professional international distributors is provided at our U�S�A� website: www�jblpro�com
Product Registration:
Register your product online at www�jblpro�com
16
Page 19
Section 9: Warranty Information
The JBL Limited Warranty on professional loudspeaker products (except for enclosures) remains in effect for ve years from the date of the rst consumer purchase. JBL ampliers are warranted for three years from the date
of original purchase� Enclosures and all other JBL products are warranted for two years from the date of original purchase�
Who Is Protected By This Warranty?
Your JBL Warranty protects the original owner and all subsequent owners so long as: A.) Your JBL product
has been purchased in the Continental United States, Hawaii or Alaska� (This Warranty does not apply to JBL products purchased elsewhere except for purchases by military outlets� Other purchasers should contact the local
JBL distributor for warranty information.); and B.) The original dated bill of sale is presented whenever warranty
service is required�
What Does The JBL Warranty Cover?
Except as specied below, your JBL Warranty covers all defects in material and workmanship. The following are not covered: Damage caused by accident, misuse, abuse, product modication or neglect; damage occurring during shipment; damage resulting from failure to follow instructions contained in your Instruction Manual; damage resulting from the performance of repairs by someone not authorized by JBL; claims based upon any misrepresentations by the seller; any JBL product on which the serial number has been defaced, modied or
removed�
Who Pays For What?
JBL will pay all labor and material expenses for all repairs covered by this warranty� Please be sure to save the original shipping cartons because a charge will be made if replacement cartons are requested� Payment of shipping charges is discussed in the next section of this warranty�
How To Obtain Warranty Performance
If your JBL product ever needs service, write or telephone us at JBL Incorporated (Attn: Customer Service
Department), 8500 Balboa Boulevard, PO. Box 2200, Northridge, California 91329 (818-893-8411). We may
direct you to an authorized JBL Service Agency or ask you to send your unit to the factory for repair� Either way, you’ll need to present the original bill of sale to establish the date of purchase� Please do not ship your JBL product to the factory without prior authorization� If transportation of your JBL product presents any unusual
difculties, please advise us and we may make special arrangements with you. Otherwise, you are responsible
for transporting your product for repair or arranging for its transportation and for payment of any initial shipping charges� However, we will pay the return shipping charges if repairs are covered by the warranty�
Limitation of Implied Warranties
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY�
EXCLUSION OF CERTAIN DAMAGES
JBL’S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT OUR OPTION, OF ANY DEFECTIVE PRODUCT AND SHALL NOT INCLUDE INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND� SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU� THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY, FROM STATE TO STATE�
17
Page 20
Rev A
Loading...