Janome DC1050 Instruction Manual

INSTRUCTION BOOK

IMPORTANT SAFETY INSTRUCTIONS

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

When using an electrical appliance, basic safety precautions should always be followed, including the

following:

This sewing machine is designed and manufactured for household use only.

Read all instructions before using this sewing machine.

DANGER— To reduce the risk of electric shock:

An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the electric outlet immediately after using and before cleaning.

WARNING— To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near

children.

2. Use this appliance only for its intended use as described in this owner’s manual.

Use only attachments recommended by the manufacturer as contained in this owner’s manual.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been

dropped or damaged, or dropped into water.

Return this sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or

mechanical adjustment.

4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this sewing machine and

foot controller free from accumulation of lint, dust and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.

11. Always use the proper needle plate. The wrong plate can cause the needle to break.

12. Do not use bent needles.

13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14. Switch this sewing machine off (“O”) when making any adjustment in the needle area, such as threading the

needle, changing the needle, threading the bobbin or changing the presser foot, and the like.

15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or

when making any other adjustments mentioned in this owner’s manual.

SAVE THESE INSTRUCTIONS

Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation relating to electrical/electronic products. If in doubt please contact your retailer for guidance. (European Union only)

TABLE OF INSTRUCTION

SECTION I. NAMES OF PARTS

Names of Parts ............................................................. 2

Standard Accessories ................................................... 3

Extension Table ............................................................. 3

SECTION II. GETTING READY TO SEW

Connecting the Power Supply ....................................... 4

Before Using Your Sewing Machine .............................. 4

Speed Control Slider..................................................... 5

Controlling Sewing Speed ............................................ 5

Machine Operating Buttons........................................ 6-7

Removing and Attaching the Foot Holder..................... 8

Changing the Presser Foot ........................................... 8

Presser Foot Lifter ........................................................ 8

Dropping or Raising the Feed Dog ............................... 9

Changing the Needle .................................................... 9

Selecting Thread and Needles ..................................... 9

Bobbin Winding ...................................................... 10-12

Threading the Machine ............................................... 13

Needle Threader ......................................................... 14

Drawing up the Bobbin Thread ................................... 15

LCD Display ................................................................ 16

Stitch Patterns............................................................. 16

Adjusting the Needle Thread Tension

for a Straight Stitch .................................................... 17

Adjusting the Needle Thread Tension

for a Zigzag Stitch ...................................................... 18

SECTION III. BASIC SEWING

Straight Stitch Sewing................................................. 19

Needle Plate ............................................................... 20

Straight Stitch.............................................................. 21

Lock-a-Matic Stitch ..................................................... 21

Locking Stitch.............................................................. 21

Stretch Stitch............................................................... 21

Tr iple Stretch Stitch ..................................................... 22

Sculpture Stitch ........................................................... 22

Saddle Stitch ............................................................... 22

Zigzag Stitch ............................................................... 23

Overcasting with Zigzag Stitch ................................... 24

Multiple Zigzag ............................................................ 24

Knit Stitch .................................................................... 24

Overedge Stitch .......................................................... 25

Various Kinds of Buttonholes and Their Uses ............. 25

Square Buttonhole .................................................26-27

Adjusting the Stitch Width and Density for

Buttonholes ................................................................ 28

Round-End Buttonhole ............................................... 28

Keyhole Buttonhole ..................................................... 28

Corded Buttonhole ...................................................... 29

Darning Stitch ............................................................. 30

Ta cking ........................................................................ 31

Eyelet .......................................................................... 31

Zipper Sewing ........................................................ 32-33

Blind Hemming............................................................ 34

Button Sewing ............................................................. 35

Shelltuck Stitch ........................................................... 35

Applique ...................................................................... 36

SECTION IV. DECORATIVE STITCHING

Scallop Stitch .............................................................. 36

Smocking .................................................................... 37

Patchwork Piecing ...................................................... 37

Fagoting ...................................................................... 38

Satin Stitches .............................................................. 38

Cross Stitch................................................................. 39

Decorative Stitches ..................................................... 39

Decorative Stitch Combinations.................................. 40

Correcting Distorted Stitch Patterns ........................... 40

SECTION V. CARE OF YOUR MACHINE

Cleaning the Hook Race and Feed Dog ..................... 41

Installing the Bobbin Holder ........................................ 41

Problems and Warning Signs ..................................... 42

Troubleshooting ........................................................... 43

SECTION I. NAMES OF PARTS

Names of Parts

Extension table (Accessory box)

q w Needle plate e Needle threader r Thread cutter t Face cover y Thread take-up lever u Thread tension dial i Spool pin o Large spool holder !0 Bobbin winder spindle !1 Bobbin winder stopper !2 Hole for additional spool pin !3 Value set buttons !4 Cursor buttons !5 LCD display !6 Speed control slider !7 Needle up/down button !8 Auto-lock button !9 Reverse stitch button @0 Start/stop button @1 Hook cover plate @2 Presser foot (Zigzag foot A) @3 Foot holder @4 Needle clamp screw @5 Needle @6 Hook cover release button @7 Power inlet @8 Foot control jack @9 Power switch #0 Handwheel #1 Carrying handle #2 Upper thread guide #3 Presser foot lifter #4 Buttonhole lever #5 Free-arm #6 Drop feed lever #7 Foot control #8 Power supply cord

#7 #8

qwert

yu io!0

!1 !2 !3

Standard Accessories

Bobbin

q w Spool pin felt e Needle set r Additional spool pin t Satin stitch foot F y Zipper foot E u Automatic buttonhole foot R i Seam ripper (Buttonhole opener) o Screwdriver key !0 Lint brush !1 Small spool holder !2 Large spool holder !333 Spool stand

Extension Table

The extension table q provides an extended sewing area and can be easily removed for free arm sewing.

q Extension table w Ta b e Slot

• Detaching the table

Pull the table away from the machine, as illustrated.

• Attaching the table

Push the extension table, inserting the tab w into the slot e until the table snaps into the machine.

• Free-arm sewing

Free-arm sewing is useful for darning socks or mending knees, cuffs or areas of wear in children’s clothes.

SECTION II. GETTING READY TO SEW

Connecting the Power Supply

• Using the foot control

Tu rn off the power switch q. Insert the foot control plug w into the foot control jack e. Insert the machine plug r into the power inlet t. Insert the power supply plug y into the wall outlet u. Tu rn on the power switch q. The foot control sign i will be displayed when the foot control is connected to the machine.

q Power switch w Foot control plug e Foot control jack r Machine plug t Power inlet y Power supply plug u Wall outlet i Foot control sign

Operating Instructions:

The symbol “O” on a switch indicates the “off” position of a switch. For appliances with a polarized plug (one blade wider than the other): To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way (U.S.A. and Canada only). *Foot control model YC-485EC-1 is used with this

sewing machine.

• Using the start/stop button

Tu rn off the power switch q. Insert the machine plug w into the power inlet e. Insert the power supply plug r into the wall outlet t. Tu rn on the power switch q.

q Power switch w Machine plug e Power inlet r Power supply plug t Wall outlet

NOTE:

The start/stop button does not work when the foot control is connected.

WARNING:

While in operation, always keep your eyes on the sewing area, and do not touch any moving parts such as the thread take-up lever, handwheel or needle. Always turn off the power switch and unplug from the power supply:

- when leaving the machine unattended.

- when attaching or removing parts.

- when cleaning the machine. Do not place anything on the foot control, otherwise the machine will run inadvertently.

Before Using Your Sewing Machine

Before using your sewing machine for the first time, place a scrap of fabric under the presser foot and run the machine without thread for a few minutes. Wipe away any oil which may appear.

Speed Control Slider

Sewing speed can be varied by the speed control slider according to your sewing needs. To increase sewing speed, slide the slider to the right. To decrease sewing speed, slide the slider to the left.

Controlling Sewing Speed

Depress the foot control to start the machine. The further down you press on the foot control, the faster the machine runs. The maximum sewing speed can be varied by the speed control slider.

Machine Operating Buttons

q Start/Stop Button

Lower the presser foot lifter. Press the start/stop button q to start the machine. The machine starts running slowly for the first few stitches; it then runs at the speed set by the speed control slider. Press the start/stop button q again to stop the machine.

NOTES:

•The machine runs slowly as long as you press and hold

the start/stop button q.

•The start/stop button q cannot be used when the foot

control is connected to the machine.

w Reverse Stitch Button

When stitches (00, 01, 10, 11) are selected, the machine will sew in reverse while the reverse stitch button is pressed.

If you press the reverse stitch button when sewing any other stitches, the machine will immediately sew locking stitches and automatically stop.

If you press the reverse stitch button when stitch pattern 00, 01, 10 or 11 is selected and the foot control is not connected, the machine will sew in reverse as long as the button is pressed, and the machine will stop when the button is released.

e Auto-lock Button

When stitches (00, 01, 10, 11) are selected, the machine will immediately sew locking stitches and automatically stop when the auto-lock button is pressed.

If you press the auto-lock button when sewing any other stitches, the machine will sew locking stitches at the end of the current pattern and automatically stop.

r Up/down Needle Position Button

Press this button to bring the needle up or down. The machine will stop with the needle up or down depending on the needle position determined by this button.

t Cursor Buttons

Use these buttons to move the cursor u.

Press button to move the cursor to right.

Press button to move the cursor to left.

y Value Set Buttons

Use these buttons to change the set value.

Move the cursor under the digit you would like to change.

Press button to increase the value.

Press button to decrease the value.

Removing and Attaching the Foot Holder

CAUTION:

Tu rn OFF the power switch before detaching or attaching foot holder.

• Removing the foot holder

Remove the setscrew q by turning it counterclockwise with a screwdriver.

• Attaching the foot holder

Match the hole in the foot holder w with the threaded hole in the presser bar e. Fit the setscrew q into the hole. Tighten the setscrew q by turning it clockwise with a screwdriver.

q Setscrew w Foot holder e Presser bar

Changing the Presser Foot

CAUTION:

Tu rn OFF the power switch before changing the foot . Always use the proper foot for the selected pattern. The wrong foot can cause the needle to break.

• Attaching the presser foot

Insert the presser foot pin q into the slit w of the presser holder and push the presser foot to lock it in place.

q Pin w Slit

• Removing the presser foot

Pull the foot in the direction of arrow to remove the presser foot.

Presser Foot Lifter

The presser foot lifter q raises and lowers the presser foot. You can raise the foot about 1/4˝ (0.6 cm) higher than the normal up position w for easy removal of the presser foot, or to help you place thick material under the foot.

q Presser foot lifter w Normal up position e Highest position

Dropping or Raising the Feed Dog

The drop feed lever is located underneath the free arm bed on the back of the machine.

q To drop the feed dog, push the lever in the direction

of the arrow q.

w To raise the feed dog, push the lever in the direction

of the arrow w, as illustrated, and turn the handwheel e toward you. The feed dog must be up for normal sewing.

Thread

Needle

#9/65–11/75

#11/75–14/90

#14/90

#14/90–16/ 100

#16/100

Light

Medium

Heavy

Fabric

Lawn Georgette Tr icot Wool, Polyester

Cotton, Polyester Fine jersey Wool

Denim Jersey Coating Quilting

Silk #80-100 Cotton #80-100 Synthetic #80-100

Silk #50 Cotton #60-80 Synthetic #50-80 Cotton #50

Silk #50 Cotton #40-50 Synthetic #40-50 Silk #30 Cotton #50

Changing the Needle

CAUTION:

Turn OFF the power switch before changing the needle.

z Tu rn off the power switch.

Raise the needle to its highest position by turning the handwheel counterclockwise, and lower the presser foot. Loosen the needle clamp screw q by turning it counterclockwise. Remove the needle from the needle clamp w.

x Insert a new needle into the needle clamp w with the

flat side to the rear. When inserting the needle into the needle clamp w, push it up as far as it goes. Tighten the needle clamp screw q firmly by turning it clockwise.

c To see if the needle is good, place the flat side of the

needle onto something flat (needle plate, glass, etc.). The gap between the needle and the flat surface should be consistent. Never use a bent or blunt needle. A damaged needle can cause permanent snags or runs in knits, fine silks and silk-like fabrics.

q Needle clamp screw w Needle clamp

Selecting Thread and Needles

For general sewing, use needle size 11/75 or 14/90. A fine thread and needle should be used for sewing lightweight fabrics, so the fabric will not be marred. Heavy fabrics require a needle large enough to pierce the fabric without fraying the needle thread. Always test the needle size on a small scrap of the fabric, which will be used for actual sewing. In general, use the same thread for the needle and bobbin. When sewing stretch fabrics, very fine fabrics and synthetics, use a BLUE TIPPED needle. The blue tipped needle effectively prevents skipped stitches.

Bobbin Winding

• Removing the bobbin

Gently slide the hook cover release button q to the right and remove the hook cover plate w. Lift out the bobbin.

q Hook cover release button w Hook cover plate

• Horizontal spool pin

Lift up the spool pin q. Place a spool of thread on the spool pin with the thread coming off the spool as shown. Attach the large spool holder w, and press it firmly against the spool of thread. The small spool holder e is used with narrow or small spools of thread.

q Spool pin w Large spool holder e Small spool holder

• Additional spool pin

The additional spool pin w is for winding bobbins, without unthreading the machine. Set the spool stand q under the additional spool pin w. Insert the additional spool pin w into the hole e. Place the felt r and a spool on the pin.

q Spool stand w Additional spool pin e Hole for additional spool pin r Spool pin felt

• Winding the bobbin

NOTE:

Set the speed control slider at its fastest position for bobbin winding.

c v

z Draw the thread from the spool. x Guide the thread around the thread guide.

c Thread through the hole in the bobbin from the inside

to the outside.

v Put the bobbin on the bobbin winder spindle.

b Push the bobbin to the right.

The bobbin sign q appears on the LCD display.

n With the free end of the thread held in your hand,

start the machine. Stop the machine when it has wound a few layers, and then cut the thread close to the hole in the bobbin.

m Start the machine again. When the bobbin is fully

wound, it will stop automatically. Return the bobbin winder to its original position by moving the spindle to the left, and cut the thread as shown.

NOTE:

For safety purposes, the machine will stop automatically 2 minutes after the start of bobbin winding.

• Inserting the bobbin

z Place a bobbin in the bobbin holder with the thread

running off counterclockwise.

q End of thread

x Guide the thread into the first notch w on the front

side of the bobbin holder.

w Notch

c Draw the thread to the left, sliding it between the

tension spring blades.

v Continue to draw the thread lightly until the thread

slips into the second notch e. Pull out about 6˝ (15 cm) of thread.

e Notch

b Attach the hook cover plate. Check the threading by

referring to the diagram r shown on the hook cover plate.

r Threading diagram

Threading the Machine

Raise the presser foot. Press the needle up/down button q to raise the thread take-up lever to its highest position. q Needle up/down button

CAUTION:

Tu rn OFF the power switch before threading the machine.

• Threading the machine

z Draw the end of the thread around the upper thread

guide.

v b

x While holding the thread near the spool w, draw the

end of the thread down around the check spring holder.

w Spool

c Firmly draw the thread up from right to left over the

take-up lever, and down into the take-up lever eye.

v Pass the thread through the lower thread guide. Slide

the thread behind the needle bar thread guide on the left.

b Thread the needle from front to back, or use the

needle threader.

+ 33 hidden pages