ITC 81420, 81421, 81423, 81426, 81427 Installation Instructions Manual

Drink Holder Installation Instructions

(Part #’s 81420, 81421, 81423, 81426 & 81427)

PARTS INCLUDED: TOOLS NEEDED (Customer Provided):

Drink Holders Electric Drill 3.625” or 4” Hole Saw Bit

IMPORTANT SAFETY INSTRUCTIONS. READ CAREFULLY FOR YOUR PROTECTION AND SAVE ALL INSTRUCTIONS.

*For part #81420, 81421 and 81423 LED lit drink holders, make sure to disconnect power before installing, adding or changing any component.
*To avoid a hazard to children, account for all parts and destroy all packing materials.

Drink Holder Warranty Information

Drink Holder Safety Instructions

GENERAL PRODUCT LIMITED WARRANTY:

ITC warrants, to the original consumer, that the product will be free of defects in materials and/or workmanship for the period of time set forth herein. This warranty period will
begin from the later of the original date of purchase of the product or the date of sale of the recreational vehicle or boat in which the product is installed is first sold to the first
consumer provided that adequate documentation of said consumer sale date is provided to ITC. Adequacy of the authenticity of the consumer sale date will be determined
by ITC in it sole discretion. In the event the consumer sale date is not provided or not determined to be adequate by ITC, then the warranty period will begin on the original
date of purchase of the product from ITC. Except as set forth below, this general product limited warranty will extend for three years. All exterior faucets, exterior showers,
exterior plumbing products, rope lighting and clocks will have a one year warranty period. All assist handles will have a two year warranty period, provided that crazing caused
by chemical attack from a contaminant is not covered by any warranty. Products that are primarily comprised of 316 stainless steel will have a five year warranty period. Bulbs,
including halogen, incandescent, xenon, and light emitting diodes (LEDs) are excluded from the warranty.

MAXIMUM LIABILITY

acceptable labor charges, acceptable freight charges, and dealer charge backs mandated by state law. ITC will not credit customers for excessive labor or freight charges or
unauthorized dealer or customer markup fees. Acceptable freight and labor charges are available from ITC upon request.

INSPECTION

inspection. The damaged item must remain available for inspection until the claim is finalized. In the event ITC requests to inspect the product, it agrees to dispatch its findings
pertaining to the alleged defective product within 45 days of receiving the product. Whenever claims are settled, I TC reserves the right to be subrogated under any existing
insurance policies the purchaser may have.

EVENTS THAT VOID WARRANTY

ITC's request; (b) ITC determines that the item has been improperly installed, altered in any way or tampered with; (c) ITC determines that the item was not used under normal
operating conditions or in accordance with labels or instructions for the item including, (d) ITC determines the product was not properly maintained, and/or; e) ITC determines
that an unauthorized repair, modification, disassembly, or other changes to the product created the alleged defect. In addition to the foregoing, this Warranty does not
protect against damage to the product when ITC determines, in its sole discretion, that the damage resulted from acts of God such as lightning, flood, earthquake, war,
vandalism, theft, normal-use wear and tear, terrorism, strikes, and labor stoppages. This warranty specificall y excludes damage, deterioration or discoloration caused by sunlight
or similar ultraviolet rays and/or wavelengths and/or dents, holes or scratches to the unit caused by stones, rocks, debris and/o r vehicles.

ITC's liability to repair or replace a damaged item shall be limited to the original purchaser of the item at the original invoice price of the damaged unit,

ITC reserves the right to review the damaged product and the site where the damage occurred. I TC may require the purchaser to ship the item to ITC for

All above warranties are null and void if any one or more of the following events occurs: (a) the item is not provided to ITC for inspection upon

Phone: [phone] • Fax: [phone] • www.elio-itc.com • [e-mail] • Revision 1: 11/18/11

230 E. Lakewood Blvd. • P.O. Box 8338 • Holland • MI • 49422-8338

Drink Holder Installation Instructions

1. Determine your installation location. Once determined drill a

3-5/8” hole using a hole saw (Note: For part #81427SS304 you
will need to drill a 4” hole).

2. If installing a standard drink holder proceed to step 3. If
installing the lit drink holder, push the LED assembly through
the rubber grommet back into the cup holder. Insert cup
holder into the hole making sure to insert the wiring first.

3. Remove the double sided tape under the rim of the drink
holder and press into the hole you made in step 1.

5. When wiring the lit version to the power source be sure to
wire the positive line (red) to the positive side and the black
line (neutral) to the neutral side.

4. For the lit version; once the holder is in place, push the LED
assembly back through the rubber grommet.

6. Contact ITC customer service at 888-871-8860 with questions
regarding the installation of this product.

+

-

Power Source

Phone: [phone] • Fax: [phone] • www.elio-itc.com • [e-mail] • Revision 1: 11/18/11

230 E. Lakewood Blvd. • P.O. Box 8338 • Holland • MI • 49422-8338