Isotech Fast-Cal Specifications
36
|
CALIBRATION SOLUTIONS
Industrial Temperature Calibrators
CompleteBasic
Thermometer
under test
Thermometer
under test
Calibrated
Standard
CERTIFICATE
for standard /
in-built indicator
-35 to 650°C
ACROSS RANGE
g
25 x 148mm Calibration Volume
g
Rugged
g
Lightweight
g
Easy to use on Site
Fast-Cal - the product range you designed !
During early 2004, 20 experienced engineers from many
parts of the world were asked to produce their ideal
specification for industrial calibration. Their top ten
requirements, in order of priority, are: Rugged, Lightweight,
Easy to use on site, Low cost/high benefit ratio, Fast
response, high stability, Time saving features, Multiple
sensor testing, Software, Modern design, Compliant with
the latest regulations.
One model is ideal for the validation of Washer Disinfectors,
Steam Sterilisers and Autoclaves. In place of a removable
insert it has a fixed block with pockets for a reference probe
and the type of test sensor commonly used in validation
applications.
Fast-Cal
Fast-Cals are available in Basic or Complete models
g
A Basic Dry Block Calibrator
The thermometer under test is compared to the dry block
controller value. Useful for moderate temperature ranges
and quick testing.
g
An ISO 9000 Calibration System
A thermometer under test is compared to a calibrated
standard, for true traceability and clearly meets the
requirements of ISO9000. Complete models include a
semi-standard probe.
37
CALIBRATION SOLUTIONS
|
Model No. HTM 2010 Low Medium High
Range at 20°C -35 to +140°C -35 to +140°C 30 to 350°C 35 to 650°C
Stability 0.02°C 0.02°C 0.03°C 0.03 to 0.05°C
Accuracy - Basic ±0.2°C ±0.2°C ±0.3°C ±1°C (500°C)
±2°C (650°C)
Accuracy - Complete* ±0.15°C ±0.15°C ±0.2°C ±0.5°C
Heating Time -30 to +140°C -30 to +140°C 50 to 350°C 50 to 650°C
In 15 minutes In 15 minutes In 15 minutes In 20 minutes
Cooling Time +140 to 0°C +140 to 0°C 350 to 100°C 650 to 300°C
In 15 minutes In 15 minutes In 40 minutes In 20 minutes
Calibration Capacity 145mm depth 148mm depth 148mm depth 148mm depth
8Ø, 6.5Ø, 3 x 4.5Ø 25mm Ø 25mm Ø 25mm Ø
Power 150W 150W 750W 750W
Traceable Certificate Included Included Included Included
UKAS Certificate Extra Extra Extra Extra
PC Communications Included Included Included Included
Software Included Included Included Included
4-20mA Input Complete Models Complete Models Complete Models Complete Models
Ramps and Dwells Yes with Software Yes with Software Yes with Software Yes with Software
Dimensions 228 x 248 x 143mm 228 x 248 x 143mm 228 x 248 x 143mm 228 x 248 x 143mm
Weight 6.60kg 6.60kg 6.35kg 6.35kg
*When used with a suitable Isotech Semi Standard PRT.
How To Order
Specify Model, Basic or Complete, Supply Voltage, Accessories and if UKAS Calibration is required.
Features (Basic & Complete) HTM 2010 LOW MEDIUM HIGH
Rugged, hard-wearing stainless steel case ü ü ü ü
Hygienic with no paint to chip or flake ü ü ü ü
No membrane keypads ü ü ü ü
Lightweight - less than 6.6kg ü ü ü ü
Thermal Switch Test - Complete Model with Software ü ü ü ü
Carrying Case included ü ü ü ü
Easy to use on site, effortless transporting ü ü ü ü
Fast response - high stability ü ü ü ü
Built-in Insert holder for ultra fast changes and restarts - - ü ü
Removable inserts, drilled to your requirements - ü ü ü
PC interface ü ü ü ü
Additional software available for automatic calibration ü ü ü ü
Certificate traceable to National Standards ü ü ü ü
Five point UKAS Certification available ü ü ü ü
Mains power variance immunity ü ü ü ü
Note: The Complete model can capture a thermostat trip temperature either as a stand alone unit or with a PC and the included software.
Low, Medium & High
Standard Insert is:
2 x 4.5mm + 1 x 6.5mm x 140mm Deep.
All Inserts have a 4mm tapped hole to
suit supplied extractor tool.
HTM2010 Fixed Block
3 x 4.5mm + 1 x 6.5mm + 1 x 8mm
x 145mm Deep.
Extra Inserts
In addition to the standard insert, specially drilled or blank
inserts are also available.
Low & Medium High
Standard 907-02-03 907-02-03d
Custom 907-02-03c 907-02-03g
Blank 907-02-03b 907-02-03f
Loading...