ION Xenon
User Guide
ION Xenon Portable Battery
User Guide
Contents
01: ION XENON AT A GLANCE __________________________ 4
Xenon overview
Accessories
Indicators
02: GETTING STARTED
Set up Xenon portable battery
03: BASICS
04: OPERATING MODES
05: TROUBLE SHOOTING
06: SAFETY AND HANDLING
07: SUPPORT
_______________________________________________ 8
Start up
Indicators
Connecting devices
Power down
About the battery
Portable battery bank mode
UPS Mode (Uninterruptable Power Supply)
General suggestions
Safety Features
Important safety information
Handling
Repairing
Battery
Charging
____________________________________________ 13
Contact details and warranty information
Specications
__________________________________ 6
________________________________ 9
_______________________________ 10
___________________________ 11
ION Xenon
User Guide
Chapter 1:
ION Xenon at a glance
Xenon overview
1 5 6 72 3 4
1 l Power Input
2 l 4 Level LED Power Bar
3 l Status Indicator
4 l Power Button
POWER INPUT Connect the provided AC adaptor to the power
4 LEVEL LED
POWER BAR
STATUS
INDICATOR
POWER
BUTTON
USB PORT 1 Connect phone, tablet or USB devices to charge.
USB PORT 2 Connect phone, tablet or USB devices to charge.
DC OUTPUT Connect higher voltage devices, laptop / tablet to
4
input (DC In) to charge the unit.
Each Blue LED represents 25% of the total
available battery power.
Status indicator is a tri-colour LED that will
change from green, yellow or red depending on
status.
Power button to operate the unit. Press and hold
down the power button for 3 seconds to turn on
or off.
5V 2.4Amps, 12Watts.
5V 2.4Amps, 12Watts.
charge. 19V/4.5Amp.
5 l USB Port 1
6 l USB Port 2
7 l DC Output
ION Xenon
User Guide
Accessories
The following accessories come with
the Xenon portable battery:
One (1) AC/DC power adapter
One (1) 10Amp IEC power cable
Indicators
Each Blue LED on the 4 level power bar represents 25% of the
total battery power available .
When the unit is being charged the blue LED lights will ash.
75-100%
50-75%
25-50%
0-25%
Status indicator is a tri-colour LED that will change from green,
yellow, or red depending on status.
Green LED Light: Battery is on and delivering
power to connected devices.
Yellow LED Light: Battery is on and power
available but there are no connected devices
drawing power.
Red LED Light: Battery is on but running low.
5
ION Xenon
User Guide
Chapter 2:
Getting Started
Set up Xenon portable battery
1
To get started with the ION Xenon
portable battery you will rst unbox the
new unit.
2
Use the supplied AC/DC adapter to
charge the system to 100% before use.
You can use the USB ports while
recharging the ION Xenon portable
battery.
3
Plug the 5.5mm / 2.1mm DC jack into
the “DC IN” located on the ION Xenon
battery. Once this has been done plug
the 3 pin Australian plug into mains to
charge the ION Xenon battery.
Please note that the ION Xenon will
automatically turn on when you plug in
the DC input. This will be indicated by
the status indicator lighting up.
6
ION Xenon
User Guide
4
To turn your ION Xenon battery On
or Off press and hold down the power
button for 3 seconds, the round status
indicator will turn orange once on if
there is no load attached.
5
Attach a load / equipment to the USB
ports or DC output.
6
The round status indicator will turn
green and the ION Xenon will be
powering the attached equipment.
7
ION Xenon
User Guide
Chapter 3:
Basics
Start up
Press the power button for three seconds to turn the ION Xenon
battery on, the round Tri colour status indicator will light up orange
if no equipment is attached.
Indicators
The ION Xenon blue LED power bar has four blue LED’s, each
indicating 25% of the total battery power available. A single press of
the power button, will show the battery charge level at any time. The
ION Xenon battery also has a tri colour status LED indicator:
Green LED Light: Battery is on and delivering power to
connected devices.
Yellow LED Light: Battery is on and power available but there are
no connected devices drawing power.
Red LED Light: Battery is on but running low.
Connecting Devices
The ION Xenon portable battery comes with two high speed
12Watt 5V, 2.5Amp USB charging outlets designed for phones,
tablets and any other compatible USB devices. It also includes a
DC output for higher voltage devices like compatible 19V/4.5Amp
laptops and tablets. Once any compatible device is attached to the
ION Xenon portable battery the Tri Colour LED will turn green to
show it is connected.
Power Down
Hold the power button until the indicator lights turn off.
About the battery
The ION Xenon comes with a 148Wh / 40,200mAh internal battery
string to keep all your devices going in times of need.
8
ION Xenon
User Guide
Chapter 4:
Operating Modes
Portable battery bank mode
The ION Xenon acts as a primary power source when devices are
connected to it while it is not connected to mains power.
UPS Mode
(Uninterruptable Power Supply)
When the ION Xenon is connected to mains power and mains
power fails the unit will act like a UPS and will turn on automatically
supplying power to the connected devices.
9
ION Xenon
User Guide
Chapter 5:
Troubleshooting
General Suggestions
PROBLEM POSSIBLE CAUSE REMEDY
No LED Power Bar
Lights or Tri LED
Lights
LED Power bar
lights on but the Tri
LED Light is orange
Tri LED Light
is red
Not charged Using the provided AC/
No devices plugged
into the Xenon
Battery power is
low
DC adaptor plug the
Xenon into mains to
charge it up.
Plug in a device to the
USB or DC output the
Tri colour light will turn
green. If the Xenon
Tri Colour light is still
orange check it has been
turned on by pressing
the power button.
Using the provided AC/
DC adaptor plug the
Xenon into mains to
charge it up.
10
ION Xenon
User Guide
Chapter 6:
Safety and handling
Safety Features
The ION Xenon Portable battery has been designed with a large
range of safety features
• Overload protection
• Overheating protection
• Output short circuit protection, will shut down under
low voltage, over voltage/current situations to protect
the device
Important safety information
Note: Rechargeable batteries have limited number of charge
cycles and may eventually need to be replaced by an ION UPS Pty
Ltd authorised provider. Battery life and number of charge cycles
vary.
WARNING: Failure to follow these safety instructions could
result in re, electric shock, injury, or damage to ION Xenon
PJ-150 or other property. Read all the safety information below
before using ION Xenon PJ-150.
Handling
Handle ION Xenon PJ-150 with care. It is made of metal, and plastic
and has sensitive electronic components inside. ION Xenon PJ-150
can be damaged if dropped, burned, punctured, crushed, or if it
comes in contact with liquid.
Repairing
Don’t open ION Xenon PJ-150 and don’t attempt to repair it
yourself.
Disassembling ION Xenon PJ-150 may damage it or may cause
injury to you. If ION Xenon PJ-150 is damaged, malfunctions or
comes in contact with liquid, contact ION UPS Pty Ltd.
11
ION Xenon
User Guide
Battery
Don’t attempt to replace the battery in ION Xenon PJ-150 yourself
as you may damage the battery which could cause overheating and
injury. The lithium-ion battery in ION Xenon should be replaced
only by ION UPS Pty Ltd, and must be recycled or disposed of
separately from household waste. Don’t incinerate the battery.
Charging
Charge ION Xenon PJ-150 with the included AC/DC adapter
and cable. Using damaged cables or chargers, or charging when
moisture is present can cause re, electric shock, injury, or damage
to ION Xenon or other property.
12
ION Xenon
User Guide
Chapter 7:
Support
Contact details and warranty
information
The ION Xenon PJ-150 comes with a 12 Month
warranty from date of purchase. For all support and
warranty claims please contact ION UPS Pty Ltd via
email or telephone technical support.
Service and support Go to: www.ionups.com.au
Technical support Call: 1300 700 805
13
ION Xenon
User Guide
Specications
Model PJ-150
Capacity 148Wh, 40,200mAh
Power Display 4 level LED battery indicator
Housing Black Aluminium housing
Outputs
Protection
2 x USB for phones or tablets
1 x 19V 4.5A Max (via 2.5mm DC Jack)
Built in short circuit, over charging and
temperature
Dimensions (mm) 123 x 24 x 235
Weight (kg) 1.05 kg
DC Input 19V / 2.5A
(2.1mm DC Jack)
DC Output 19V / 4.5A (2.5mm DC Jack)
USB1 Output 5V / 2.4A
USB2 Output 5V / 2.4A
AC Input Power 100~240V
Time to full charge 3.5~4 hours
14
ION Xenon
User Guide
info@ionups.com.au
www.ionups.com.au
Phone: 1300 700 805
International: +61 2 9096 2700
Loading...