www.iomega.com
DVD ATAPI Drive
Quick Install
3
PHONES
OPEN
CLOSE
w
w
w
.
io
m
e
g
a
.
c
o
m
In
stallation r
Gr
In
Unidad
st
alaci
d
Inst
e D
ón
U
VD
nidade
a
rápida
lação rá
D
VD
AT
API
pida
C
aveurD
AT
o
p
y
Quic
apide
API
w
r
i
g
h
t
©
A
l
D
VD
kI
VD
AT
w
w
.io
2
0
0
3
l
r
i
g
h
t
s
CD de Soluciones
ATAPI
nstall
API
m
e
I
o
m
r
e
s
e
L
ö
sungs-CD • CD Solutions
CD de Soluçõ
D
rive
0
3
g
a
.
c
o
m
e
g
a
C
o
r
p
o
r
r
v
a
e
t
d
i
o
.
n
.
Solutions CD
2
1
7
6
•
0
1
• CD Soluzioni
•
es
4
IMPORTANT: Your computer configuration may vary from the illustrations. If you are familiar
with installing internal ATAPI drives, this guide may be sufficient, otherwise, you will need
printed instructions from the User’s Manual on the Solutions CD.
Write down the serial number: _____________________________________________________
1
PHONES
OPEN
CLOSE
5
Insert the Solutions CD and select your language.
2
S
Lös
o
lu
u
n
C
g
D
s
d
-C
e
D
S
o
lu
c
io
n
C
D
d
e
S
0
2
3
1
7
6
w
w
w
Co
.io
py
m
rig
e
g
ht
a
©
.
c
20
o
m
0
3 Io
All rights re
me
ga Corpora
s
e
rve
tion.
d
.
tio
n
s
C
D
• C
D
S
o
lu
e
s
t
io
• C
n
D
s
S
o
o
lu
lu
ç
z
õ
io
e
n
s
i
•
•
0
1
6
Click on the
User’s Manual
icon, select “Click to View”, then select “Installing the Drive”,
then select “Connecting the Drive” and print the detailed instructions now.
NOTE: If at any step you need help, refer to the instructions you printed.
374
Shut down the computer, disconnect the power cord, and remove the cover.
8
Verify your jumper settings are correct. Refer to the instructions you printed for details.
5
9
Locate a vacant 5.25" drive bay and remove the panel cover. Slide the drive into the drive
bay.
6
OPEN
CLOSE
PHONES
Connect the audio cable to the drive and then to the computer’s audio connection,
usually located on the sound card or the motherboard.
NOTE: If you are unable to find the computer’s audio connection, refer to your sound card or
computer documentation for instructions.
MASTER
SLAVE
CABLE SELECT
AUDIO OUT
R GND L
C S M
S L A
IDE PIN1
DC INPUT
+5 GND
+12
10
7
11
Connect the IDE data cable that shipped with the drive to the back of the DVD drive
and to the secondary channel on the motherboard.
NOTE: If another drive is connected to the secondary IDE channel, refer to the printed instructions.
8
CABLE SELECT
AUDIO OUT
R GND L
MASTER
SLAVE
C S M
S L A
2
IDE PIN1
DC INPUT
+5 GND +1
12
Connect a spare power supply cable from the computer to the drive.
NOTE: If there is no spare power supply cable, you may need to purchase a y-cable power adapter.
9
IDE PIN1
DC INPUT
+5 GND +12
MASTER
SLAVE
A
C S M
S L
CABLE SELECT
AUDIO OUT
R GND L
13
Replace the cover, connect the power cord and restart your computer. An icon for your
DVD drive will appear in My Computer. If it does not, see Troubleshooting in the User’s
Manual on the Solutions CD.
10
14
One or more software solutions will need to be installed on your computer to use your
drive. To install software, click on a software icon, then select “Click to Install” to start
the software installation. Refer to the DVD wizard included with HotBurn Pro for
information on using the software solutions with your drive.
11
15
For important information about your DVD drive, refer to the User’s
Manual on the Solution CD.
You must have Microsoft
®
Internet Explorer 5.0 or higher or Netscape
Navigator
®
6.1 or higher installed on your system.
Lösungs-CD • CD Solutions
Solutions CD
CD de Soluciones • CD Soluzioni
Cd-rom Oplossingen • CD de Soluções
7
1
6
2
0
0
1
3
www.iomega.com
Copyright © 2003 Iomega Corporation.
All rights reserved.
16
Act Now—Register Online
If you have not already registered, we have made it easier and faster to
register your Iomega product. Simply enter the web address
http://www.iomegareg.com/en to register online.
17
Customer Support Options
For service and support for your Iomega product, visit us at http://www.iomega.com.
You can also view a multimedia tutorial on using your DVD drive and software. This is
currently available only in English at http://www.iomega.com/support/def_cdrw.html.
CI
18
IMPORTANT! It may be a criminal offense under applicable copyright laws to make
unauthorized copies of copyright-protected material, including computer
programs, videos, films, broadcasts, non-original sound and video recordings. This
equipment should NOT be used for such purposes.
CLASS 1
LASER PRODUCT
Copyright © 2003 Iomega Corporation. All rights reserved. Iomega, the stylized “i” logo, and all Iomega brand blocks are either registered
trademarks or trademarks of Iomega Corporation in the United States and/or other countries. Microsoft and Windows are either registered
trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Certain other product names, brand names, and
company names may be trademarks or designations of their respective owners.
Manufacturer/Responsible Party
Iomega Corporation
1821 West 4000 South
Roy, UT 84067 USA
www.iomega.com
30420600 7/9/03 b
Loading...