Invacare RBL250 User Manual
Reliant Bath Lift (RBL250) Flap Kit
Assembly, Installation and Operating Instructions
Kit No. 1085140
NOTE: Check all parts for shipping damage before
using. In case of damage, DO NOT use. Contact the
Dealer/Carrier for further instructions.
SAFETY SUMMARY
The following recommendations are made for the
safe replacement of the FLAP KIT on the Reliant Bath
Lift (RBL250).
GENERAL WARNINGS
DO NOT assemble or use this kit without first
reading and understanding this instruction
sheet. If you are unable to understand the
Warnings, Cautions and Instructions in this
sheet and in the Owner's Operating and
Maintenance Manual (Part No. 1081003),
provided with the Bath lift, contact a healthcare professional, dealer or technical personnel before attempting to install this kit,
otherwise, injury or damage may occur.
INSTALLATION WARNINGS
When installing or removing the Battery
pack ALWAYS hold the battery pack firmly,
otherwise injury or damage may result.
To prevent frame from tipping when raising or lowering, either suction the frame
to the floor or place one foot on the frame
base when removing/installing the seat.
This kit contains the following:
DESCRIPTION QTY
Flaps 2
Screws 4
Nuts - Self Locking 4
Washers 4
Hinges 4
Pins 4
Circlip 8
Instruction Sheet 1
REPLACING THE BATH LIFT FLAPS
Removing the Bath Lift Seat (FIGURES 1-7)
Pendant
Up
FIGURE 1 - RAISING THE BATH LIFT
2. Remove the battery pack by grasping the handgrip
on battery pack and pulling upwards (FIGURE 2).
PULL UP TO
REMOVE
Battery Pack
é
Handgrip
Frame
FIGURE 2 - REMOVING THE BATTERY PACK
3. To release the seat, press and hold the spring loaded
chair release button (FIGURE 3).
WARNING
To prevent pinching injury between seat
back and motor shroud when removing/
installing the seat, DO NOT grasp seat
anywhere other than at the recess at
the top (FIGURE 3), the opening at the
bottom of the seat or the lip where the
battery pack was.
CAUTION
DO NOT remove the seat until the bath Lift
is raised to the upper limit. Otherwise damage may occur.
Motor Shroud
Recess
Spring Loaded
Chair Release
Button
Battery Pack
Seat
FIGURE 3 - RELEASING THE SEAT
NOTE: Refer to the GENERAL WARNINGS in the
SAFTY SUMMARY of this Instruction Sheet.
1. Raise the Bath Lift seat by pressing the UP (é)
button on the pendant (FIGURE 1).
NOTE: The lift will automatically stop at the top and
bottom limits if UP/DOWN buttons are not released.
4. While holding the spring loaded chair release button
with one hand, grasp the seat bottom firmly with your
other hand.
5. Lift the seat up until the slide block comes free of the
grooves on the bath lift frame to remove the seat from
the frame (FIGURE 4).
1
LIFT THE SEAT
Slide Block
Frame
Groove
FIGURE 4 - REMOVING THE SEAT
REMOVING/INSTALLING FLAPS
(FIGURES 8 - 10)
1. T urn seat upside down.
2. Remove the two (2) self locking nuts, two (2) washers and two (2) screws that secure the hinges to the
side of the seat.
3. Remove EXISTING flap with hinges (FIGURE 8).
Self Locking Nut
Flap
Screws
6. Grasp the handgrip and slide the battery pack
onto the charger connector on the frame (FIGURE 5).
PUSH DOWN
ê
TO INSTALL
Battery Pack
Handgrip
Frame
FIGURE 5 - INSTALLING THE BATTERY PACK
NOTE: The battery pack should fit snugly and not
wobble.
7. Lower the bath lift by pressing the DOWN (ê)
button on the pendant (FIGURE 6).
Down
Pendant
Washer
Hinges
Washer
Bath Lift Seat (Bottom)
Nut
FIGURE 8 - REMOVING/INSTALLING FLAPS
4. Lay NEW flap bottom side up.
5. Place NEW hinge into recess in the side of the NEW
flap (FIGURE 9).
FIGURE 6 - LOWERING THE BATH LIFT
NOTE: The lift will automatically stop at the top and
bottom limits if UP/DOWN buttons are not released.
8. Remove the battery pack by grasping the handgrip
on battery pack and pulling upwards (FIGURE 7).
PULL UP TO
REMOVE
Battery Pack
é
handgrip
Frame
FIGURE 7 - REMOVING THE BATTERY PACK
6. Insert pin through the holes in the flap and the hinge
as shown in FIGURE 9.
7. Perform the following procedure to install one (1) circlip
on each end of pin (DETAIL A):
A . Place the open side of the circlip into the grooves
at the ends of the pin.
B. Position a screwdriver at the top of the circlip.
C. Apply pressure to the circlip until an audible "click"
is heard.
2
Loading...