Intermatic T10404R User Manual

TIME SWITCH OPERATING INSTRUCTIONS

1. TO SET “ON” AND “OFF” TIMES: Hold TRIPPERS

against edge of CLOCK-DIAL, point­ing to time (AM or PM) when ON
and OFF operations are desired.
Tighten tripper screws firmly.

2. TO SET TIME-OF-DAY: Pull
CLOCK-DIAL outward. Turn in

either direction and align the exact
time-of-day on the CLOCK-DIAL (the time now, when
switch is being put into operation) to the POINTER.

DO NOT MOVE POINTER

• TO OPERATE SWITCH MANUALLY: Move
MANUAL LEVER below CLOCK-DIAL left or right as
indicated by arrows, This will not affect next
operation.

• FORMORETHANONEDAILYON-OFF

OPERATION: Place additional tripper pairs on CLOCK­DIAL (order 156T1978A).

• INCASEOFPOWERFAILURE, reset CLOCK-DIAL
to proper time-of-day. See step 2 above.

INTERMATIC INCORPORATED

SPRING GROVE, ILLINOIS 60081-9698

158TP10864

CLOCK
DIAL

TIME
POINTER

OFF
TRIPPER

MANUAL
LEVER

ON
TRIPPER

TIME SWITCH RATINGS:

DOUBLEPOLESINGLETHROW(DPST)

30 AMP, RESISTIVE, INDUCTIVE, TUNGSTEN
OR 1000 VA PILOT DUTY - 120/208/240 VAC
2 HP (24 FLA)-120 VAC, 5 HP (28 FLA)-240 VAC

CLOCKMOTOR:208/277VOLTS-60HZ.

(TO ORDER CLOCK MOTOR REPLACEMENT,SPECIFY PART NO.
WG--ON MOTOR COVER)

MODEL: T10404R

IN RAINPROOF (TYPE 3R) ENCLOSURE FOR INDOOR OUTDOOR USE

SUITABLE FOR SWIMMING POOL / SPA APPLICATIONS AND FOR DIRECT CONNECTION OF UNDERWATER LIGHTS.

92 AMP PER LEG, 168 AMP MAX., 120/240 VOLT OR 120/208 VOLT SINGLE PHASE, (THREE WIRE) AC.

IMPORTANT: This Control Panel must be installed according to the National Electrical Code (including Article 680)

or Canadian Electrical Code (including Section 68) and Local Electrical Codes. This installation is subject to the approval
by the local inspection authority. USE COPPER CONDUCTORS ONLY. Do not exceed the maximum ratings of individual
components, wiring devices, and current carrying capacity of conductors. If heater protection is required, install FIREMAN
SWITCH kit (156T4042A may be ordered). For grounding of the installation, refer to Article 250 and 680 of the National
Electrical Code. (For Canadian Installations: Section 10 and 68 of the Canadian Electrical Code). Install only APPROVED
wiring device(s) inside the enclosure. An APPROVED wiring device may be installed in the rectangular side
knockout provided. When panel is outdoors, an APPROVED rainproof cover must be installed over the wiring
device in the side knockout. If this enclosure is used for direct connection of underwater lights, refer to 1999 NEC 680­21(b), 2002 NEC 680-24(b) or CEC 68-060, 062 and 066 for further details. This Control should not be connected to any
equipment which would cause bodily injury or property damage should it be activated unexpectedly. After wiring, install
front panel over wiring compartment. KEEP DOOR CLOSED AT ALL TIMES.

NOTES:

1. Any Intermatic T100M or ET100CM series Time Switch, P1353ME
3 Circuit Control, PF1000M Series Freeze Protection or RC2000M Series
Air Switch Mechanism may be installed in the bracket provided or in the
event an existing mechanism is replaced.

2. If this control panel requires bonding, attach an APPROVED bonding
terminal of a suitable size using the mounting hole(s) provided on the
bottom of the enclosure (156T11047A may be ordered).

3. Wiring devices may be installed in this control panel (order
21T156A (4) Standoffs for mounting).

CONTROL PANEL WITH
TWO TIME SWITCHES

LR3730

UL508
UL1563
NEC680

WIRING DIAGRAM AND INSTRUCTIONS FOR INTERCONNECTING TIME

SWITCHESWHENUSEDASSWIMMINGPOOLEQUIPMENTCONTROL

1. Disconnect the clock motor leads of the CLEANER CONTROL TIMER.

2. Connect 240 volt supply and the clock motor leads of the CLEANER
CONTROL TIMER to terminals #1 and #3 of the FILTER TIMER.

3. Connect terminals #2 and #4 of Filter Timer to terminals #1 and #3 of the
Cleaner Control Timer (using short jumpers).

4. Connect 240 volt load of cleaner pump to terminals #2 and #4 of
CLEANER CONTROL TIMER.

CLOCK
MOTOR

CLOCK
MOTOR

SUPPLY

TO FILTER

PUMP

TO POOL
CLEANER

FILTER TIMER

CLEANER CONTROL TIMER

WIRING INFORMATION - COPPER CONDUCTORS ONLY

GENERAL

GENERAL PURPOSE
PURPOSE BRANCH
BRANCH CIRCUIT
WIRE SIZE CIRCUIT MAXIMUM
75˚C MIN TERMINAL BREAKER CURRENT
INSULATION TORQUE 120V. 240V. RATING CAPACITY

AWG LB-IN HP HP AMP AMP

14 20 1/2 1 15 12
12 20 1 2 20 16
10 20 1 1/2 3 30 24
8 25 2 5 40 32

MAX MOTOR
LOAD
(CONTINUOUS
DUTY)