Interlogix TruVision Intelligent IP Dome Installation Manual
TruVision 12/32 Series
IP Camera Installation
Guide
P/N 1072880-EN • REV B • ISS 08JAN15
Copyright © 2015 United Technologies Corporation,
Interlogix is part of UTC Building & Industrial
Trademarks and
patents
Manufacturer Interlogix
Systems, a unit of United Technologies
Corporation. All rights reserved.
Trade names used in this document m ay be trademarks
or registered trademarks of the manufac turers or
vendors of the respective products.
2955 Red Hill Avenue, Costa Mesa, CA 92626- 5923,
USA
Authorized EU manufacturing representat ive:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherl ands
Certification
FCC compliance Class A: This equipment has been tested and found to
ACMA compliance Notice! This is a Clas s A product. In a domestic
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These l imits are
designed to provide reasonable protectio n against
harmful interference when the equipm ent is operated in
a commercial environment. This equipm ent generates,
uses, and can radiate radio frequency energ y and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this eq uipment in a
residential area is likely to caus e harmful interference in
which case the user will be required to correct the
interference at his own expense.
environment this product may cause rad io interference
in which case the user may be required to take
adequate measures.
Canada This Class A digital apparatus c omplies with Canadian
N4131
ICES-003.
Cet appareil numérique de la classe A es t conforme à
European Union
directives
Contact information For contact information, see www.interlogix .com or
la norme NMB-0330 du Canada.
12004/108/EC (EMC directive): Hereby, UT C Fire &
Security declares that this device is in compliance with
the essential requirements and other r elevant
provisions of Directive 2004/108/EC.
2012/19/EU (WEEE directive): Produc ts marked with
this symbol cannot be disposed of as unsor ted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon
the purchase of equivalent new equipm ent, or dispose
of it at designated collection points. F or more
information see: www.recyclethis.info.
www.utcfssecurityproducts.eu.
Content
Introduction 2
Product overview 2
Installation 3
Installation environment 3
Package contents 4
Cable requirements 12
Camera description 13
Setting up the camera 17
IR illuminators 18
Accessing the SD card 19
Mounting the bullet camera 19
Mounting the VF dome camera 20
Mounting the outdoor dome camera 25
Using the camera with an Interlogix NVR or Hybrid DVR or
another system 30
Using the camera with TruVision Navigator 30
Specifications 30
TruVision IP box cameras 30
TruVision IP VF mini dome 31
TruVision IP VF bullet cameras 32
TruVision IP VF outdoor dome cameras 32
Pin definitions 33
Installation Guide 1
Introduction
Product overview
This is the installation guide for TruVision 12/32 Series IP
camera models:
TVC-1201 (1.3MPX IP box camera, PAL)
TVC-3201 (1.3MPX IP box camera, NTSC)
TVC-1202 (3MPX IP box camera, PAL)
TVC-3202 (3MPX IP box camera, NTSC)
TVB-1201 (1.3MPX IP bullet camera, 2.8-12mm, PAL)
TVB-3201 (1.3MPX IP bullet camera, 2.8-12mm, NTSC)
TVB-1202 (3MPX IP bullet camera, 2.8-12mm, PAL)
TVB-3202 (3MPX IP bullet camera, 2.8-12mm, NTSC)
TVB-1203 (3MPX IP bullet camera, 8-32mm, PAL)
TVB-3203 (3MPX IP bullet camera, 8-32mm, NTSC)
TVD-1201 (1.3MPX IP VF mini dome, 2.8-12mm, PAL)
TVD-3201 (1.3MPX IP VF mini dome, 2.8-12mm,
NTSC)
TVD-1202 (3MPX IP VF mini dome, 2.8-12mm, PAL)
TVD-3202 (3MPX IP VF mini dome, 2.8-12mm, NTSC)
TVD-1203 (1.3MPX IP outdoor dome, 2.8-12mm, PAL)
2 Installation Guide
TVD-3203 (1.3MPX IP outdoor dome, 2.8-12mm,
NTSC)
TVD-1204 (3MPX IP outdoor dome, 2.8-12mm, PAL)
TVD-3204 (3MPX IP outdoor dome, 2.8-12mm, NTSC)
TVD-1205 (3MPX IP outdoor dome, 8-32mm, PAL)
TVD-3205 (3MPX IP outdoor dome, 8-32mm, NTSC)
Installation
This section provides information on how to install the
cameras.
Installation environment
When installing your product, consider these factors:
• Electrical: Install electrical wiring carefully. It should be
done by qualified service personnel. Always use a proper
PoE switch or a 12 VDC UL listed Class 2 or CE certified
power supply to power the camera. Do not overload the
power cord or adapter.
• Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.
• Temperature: Do not operate the camera beyond the
specified temperature, humidity or power source ratings.
The operating temperature of the camera without heater
is between -30 to +60°C (-22 to 140°F). Humidity is below
90%. For the outdoor cameras have built-in heaters, the
operating temperature range is -40°C to 60°C(-40°F
to140°F)
• Moisture: Do not expose the camera to rain or moisture,
or try to operate it in wet areas. Turn the power off
Installation Guide 3
immediately if the camera is wet and ask a qualified
service person for servicing. Moisture can damage the
camera and also create the danger of electric shock.
• Servicing: Do not attempt to service this camera
yourself. Any attempt to dismantle or remove the covers
from this product will invalidate the warranty and may
also result in serious injury. Refer all servicing to qualified
service personnel.
• Cleaning: Do not touch the sensor modules with fingers.
If cleaning is necessary, use a clean cloth with some
ethanol and wipe the camera gently. If the camera will not
be used for an extended period of time, put on the lens
cap to protect the sensors from dirt.
Package contents
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use
the unit; contact the supplier immediately. If the unit is
returned, it must be shipped back in its original packaging.
4 Installation Guide
IP box camera
Camera C-CS adaptor
CD with Configuration
manual and TruVision
Device Finder
WEEE and Battery
Disposal
Installation manual
Installation Guide 5
IP VF bullet camera
Camera
Template
2
Ceiling Mounting
1
1
22
1:Screw Hole for
2:Screw Hole for
Bracket
Mounting Base
1
1
2
Screws M4.8 × 18, 4pcs
to attach the back box
Back box
Alarm connector
(2 pcs)
Screws (4 pcs)
6 Installation Guide
Water joint: provide
water resistance to
network connection.
Video cable
CD with Configuration
manual and TruVision
Device Finder
Wrench
Installation manual WEEE and Battery
Disposal
Installation Guide 7
IP VF dome camera
Camera
Template
Drilling Templater
Adaptor: for TVD-CB3
cup base
12 VDC Connector:
DC jack socket to
terminal connectors
with positive and
negative indicators.
8 Installation Guide
Loading...