Interlogix TruVision Camera Mounts User Manual

TruVision Dome Brackets Installation Manual
P/N 1072649B-EN • REV 1.0 • ISS 30SEP13
Copyright © 2013 UTC Fire & Security Americas Corporation, Inc.
Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies Corporation. All rights
reserved.
Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or
vendors of the respective products.
Certification
Contact information For contact information, see www.utcfireandsecurity.com or www.utcfssecurityproducts.eu.
N4131
2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal
waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
Content
Introduction 2
Bracket and cup base descriptions 2
Wall-mount installation (TVD-SNB and TVD-M2-WM) 4
5-inch dome cameras 4 3-inch dome cameras 6 2-inch dome wedge cameras 7
Flush-mount installation (TVD-M2-FM) 8
5-inch dome indoor cameras 8
Pendant-mount installation (TVD-PPB) 10
5-inch dome cameras 10 3-inch dome cameras 11 2-inch dome wedge cameras 12
Pole-mount installation (TVD-M-PMA) 13
Specifications 14
Pipe threading information 15
Overview: Fixed dome cameras by bracket 16
TruVision Dome Brackets Installation Manual 1

Introduction

These are the installation instructions for the TruVision series of dome brackets and cup bases. The series brackets and cup bases are compatible with both indoor and outdoor Interlogix cameras
Models
For a list of the brackets and cup bases with their corresponding cameras, see “Overview: Fixed dome cameras by bracket” on page on page 16.
Packet contents
The package contains the following items:
Bracket or cup base
Accessories for installation
• Screws
Unpacking
Please check the package contents to ensure that all parts are present and in good condition.
Note: For safety purposes, the mounting surface must be able to support three times the combined weight of the bracket, cup base, and camera.

Bracket and cup base descriptions

TruVision dome swan-neck bracket (TVD-SNB)
TruVision dome pendant-mount ceiling bracket (TVD-PPB)
Mounting plate
Tube
2 TruVision Dome Brackets Installation Manual
TruVision flush-mount bracket (TVD-M2-FM)
TruVision pole-mount adaptor (TVD-M-PMA)
TruVision indoor dome wall-mount bracket (TVD-M2-WM)
TruVision dome cup bases
• TVD-CB5:
Note: The rubber ring for TVD-CB5 is pre-installed in the cup base.
• TVD-CB5A:
Note: The rubber ring for TVD-CB5A is pre-installed in the cup base.
TruVision Dome Brackets Installation Manual 3
• TVD-CB3:
• TVD-CB2:
Accessories
Converter pan (TVD-M2 WEBM)
Screw Ø 4 mm (2
pieces)
Expansion screw
Ø 10 mm (5 pieces)
Screw Ø 4 mm
(4 pieces)
Locking screw Ø 4 mm
(2 pieces)
Black screw Ø 4 mm
(4 pieces)
Wall-mount installation (TVD-SNB and TVD-M2­WM)
Check the section “Overview: Fixed dome cameras by bracket” on page 16 to confirm that the correct bracket is used with the camera.

5-inch dome cameras

Use the TVD-SNB bracket and the TVD-CB5/TVD-CB5A cup base. See “Bracket and cup base description” on page 2 for examples of the assembled brackets.
To mount a swan-neck bracket on a wall:
1. Pull the camera cables through the bracket tube and then attach the swan-neck bracket to the wall with the expansion screws (A) provided.
4 TruVision Dome Brackets Installation Manual
2. Screw the cup base onto the swan-neck bracket and fasten with the locking screw, as shown.
3. TVD-CB5 only:
Using the enclosed screws, attach the cup base to the camera housing.
4. Loosen the screws on the dome enclosure (1) using the supplied hex wrench, and remove the enclosure and dome liner (2).
5. Connect the cables to the dome camera.
6. Insert the dome module into the cup base (TVD­CB5A shown) and attach using the enclosed screws.
7. Re-attach the dome liner and enclosure to the camera.
TruVision Dome Brackets Installation Manual 5

3-inch dome cameras

Use the TVD-SNB bracket with the TVD-CB3 cup base or TVD-M2-WM bracket. See “Bracket and cup base description” on page 2 for examples of the assembled brackets.
To mount a swan-neck bracket on a wall:
1. Pull the camera cables through the TVD-SNB bracket tube and then attach the swan-neck bracket to the wall with the expansion screws (A) provided.
2. Screw the cup base onto the swan-neck bracket and fasten with the locking screw, as shown (A).
Then attach the mounting plate (B) to the cup base.
Note: The mounting plate is shipped with the dome camera.
3. Loosen the screws on the dome enclosure using hex wrench, and remove the dome enclosure and the liner.
4. Connect the cables to the dome camera.
5. Using the enclosed screws, attach the dome module of the camera (A) to the bracket.
Then re-attach the dome liner and enclosure (B).
6. Re-attach the dome enclosure to the camera.
6 TruVision Dome Brackets Installation Manual
To mount an indoor wall-mount bracket:
1. Pull the camera cables through the TVD-M2-WM bracket tube and then attach the bracket to the wall with the expansion screws (A) provided.
2. Attach the mounting plate to the bracket.
Note: The mounting plate is shipped with the dome camera.
3. Loosen the screws on the dome enclosure using the supplied hex wrench and remove the dome enclosure and liner from the dome module.
4. Connect the cables to the dome camera.
5. Using the enclosed screws, attach the dome module of the camera to the bracket.
6. Re-attach the dome liner and enclosure to the camera.

2-inch dome wedge cameras

Use the TVD-SNB bracket and the TVD-CB2 cup base. See “Bracket and cup base description” on page 2 for examples of the assembled brackets.
To mount a swan-neck bracket on a wall:
1. Pull the camera cables through the bracket tube and then attach the swan-neck bracket to the wall with the expansion screws (A) provided.
2. Using four screws, attach the converter pan (TVD-M2 WEBM) to the cup base.
TruVision Dome Brackets Installation Manual 7
3. Then screw the cup base onto the swan-neck bracket and fasten with the locking screw.
4. Loosen the screws on the dome enclosure using the supplied hex wrench and remove it.
5. Connect the cables to the dome camera.
Using two screws, attach the camera base plate to the converter pan on the cup base.
6. Re-attach the camera enclosure to the camera.

Flush-mount installation (TVD-M2-FM)

Check the section “Overview: Fixed dome cameras by bracket” on page on page 16 to confirm that the correct bracket is used with the camera.
Note: For safety purposes, the mounting surface must be able to support three times the combined weight of the bracket, cup base, and camera.

5-inch dome indoor cameras

Use the TVD-M2-FM bracket. See “Bracket and cup base description” on page 2 for examples of the assembled brackets.
To mount a flush-mount bracket on a ceiling:
1. On the false ceiling, mark the position and size of the housing pass-through hole. Cut a hole with a diameter of between 176 and 180 mm. Make sure the cables for the camera are prepared.
Note: The ceiling thickness must be less than 30 mm.
8 TruVision Dome Brackets Installation Manual
2. Using screws provided, fasten the mounting plate (A) to the in-ceiling mounting base (B).
3. Push the dome camera into the in-ceiling mounting base.
Caution: For safety reasons, use safety cables to securely attach the camera dome to the in­ceiling mounting base and to attach the in-ceiling mounting base to the building’s infrastructure.
4. Rotate the camera 10 degrees counterclockwise (A) and then securely fasten the camera to the in-ceiling mounting base using the lock screws (B).
5. Push the camera with in-ceiling mounting base into the ceiling hole.
Safety
cable
6. Using the lock screws (A), securely fasten the camera to the ceiling.
7. To set up the camera image, remove the camera enclosure and connect the RCA analog video output to a monitor (D).
Loosen the lens set screw (E) and pan (A), tilt (B) or rotate (C) the lens to obtain the desired surveillance angle. Adjust the lens focus. When all adjustments have been done, refasten the lens set screw.
8. Using screws, attach the trim ring to the in-ceiling mounting base on the ceiling.
TruVision Dome Brackets Installation Manual 9

Pendant-mount installation (TVD-PPB)

Check the section “Overview: Fixed dome cameras by bracket” on page16 to confirm that the correct bracket is used with the camera.

5-inch dome cameras

Use the TVD-PPB bracket and the TVD-CB5/TVD-CB5A cup base. See “Bracket and cup base description” on page 2 for examples of the assembled brackets.
To mount a pendant-mount bracket on a ceiling:
1. Screw the mounting plate onto the tube and fasten with the locking screw.
2. Pull the camera cables through the bracket tube and then attach the bracket to the ceiling with expansion screws.
3. Screw the cup base onto the tube and fasten with the locking screw.
4. TVD-CB5 only:
Using the enclosed screws, attach the camera housing to the cup base.
5. Loosen the screws on the dome enclosure (1) using the supplied hex wrench, and remove the dome enclosure and liner (2).
10 TruVision Dome Brackets Installation Manual
6. Connect the cables to the dome camera.
7. Insert the dome module into the cup base.
8. Re-attach the dome liner and enclosure to the camera.

3-inch dome cameras

Use the TVD-PPB bracket and the TVD-CB3 cup base. See “Bracket and cup base description” on page 2 for examples of the assembled bracket.
To mount a pendant-mount bracket on a ceiling:
1. Screw the mounting plate onto the tube and fasten with the locking screw, as shown.
2. Pull the camera cables through the bracket tube and then attach the bracket to the ceiling with expansion screws.
3. Screw the cup base onto the tube and fasten with the locking screw (A).
Using the enclosed screws, attach the camera mounting plate (B) to the cup base.
Note: The camera mounting plate is shipped with the dome camera.
4. Loosen the screws on the dome enclosure (1) using the supplied hex wrench, and remove the dome enclosure and liner (2).
TruVision Dome Brackets Installation Manual 11
5. Connect the cables to the dome camera.
6. Using screws, attach the dome module to the mounting plate.
7. Re-attach the dome liner and enclosure to the camera.

2-inch dome wedge cameras

Use the TVD-PPB bracket and the TVD-CB2 cup base.
To mount a pendant-mount bracket on a ceiling:
1. Screw the mounting plate onto the tube and fasten with the locking screw, as shown.
2. Pull the camera cables through the bracket tube and then attach the bracket to the ceiling with expansion screws.
3. Using four screws, attach the converter pan TVD-M2 WEBM to the cup base.
Then screw the cup base onto the pendant­mount bracket and fasten with the locking screw.
4. Loosen the screws on the dome enclosure using the supplied hex wrench and remove it.
12 TruVision Dome Brackets Installation Manual
5. Using 2 screws, attach the camera base plate to the converter pan.
6. Re-attach the camera enclosure to the camera.

Pole-mount installation (TVD-M-PMA)

Check the section “Overview: Fixed dome cameras by bracket” on page16 to confirm that the correct bracket is used with the camera.
Use the TVD-M-PMA pole-mount adaptor to mount a camera on a pole.
To mount a swan-neck bracket on a pole:
1. At the desired mounting place, securely fasten the TVD-M-PMA pole-mount adaptor to the pole. Pull the cables through the mount.
2. Pull the camera cables through the TVD-SNB bracket tube and then attach the bracket to the pole mount with the expansion screws provided.
3. Screw the cup base onto the swan-neck bracket and fasten with the locking screw, as shown (A).
Then attach the mounting plate (B) to the cup base.
Note: The mounting plate is shipped with the dome camera.
TruVision Dome Brackets Installation Manual 13
4. Loosen the screws on the dome enclosure using the supplied hex wrench, and remove the dome enclosure and liner.
5. Connect the cables to the dome camera.
6. Using the enclosed screws, attach the dome module of the camera to the bracket.
7. Re-attach the dome liner and enclosure to the camera.
To mount a bullet camera on a pole:
1. At the desired mounting place, securely fasten the TVD-M-PMA pole-mount adaptor to the pole. Pull the cables through the mount.
2. Connect the cables to the camera.
3. Use the enclosed screws to attach the camera to the pole mount.
4. Adjust the camera position and angle as required.

Specifications

SKU Dimensions Weight
TVD-SNB 253 × 95 × 180 mm 490 g (1.2 lb)
TVD-PPB Ø 150 × 537 mm 1169 g (2.56 lb)
TVD-M2-FM Ø 210 × 90 mm 540 g (1.19 lb)
TVD-M-PMA 117 × 194 × 143 mm 1205 g (2.66 lb)
TVD-M2-WEBM Ø135 × 9 mm 25 g (0.05 lb)
TVD-M2-WM Ø135 × 182.5 × 251 mm 580 g (1.28 lb)
TVD-CB5 Ø 160 × 80 mm 490 g (1.2 lb)
TVD-CB5A Ø 160 × 100 mm 340 g ( 0.75 lb)
TVD-CB3 Ø 140 × 60 mm 320 g (0.71 lb)
14 TruVision Dome Brackets Installation Manual
TVD-CB2 Ø 124 × 57 mm 190 g (0.42 lb)

Pipe threading information

Pipe
thread
Threads
size
G 1 11 2.309 33.249 1.309 25 33.7 1.33 3.2 30.75
/ in
Pitch (mm)
Thread major
diameter
(mm) (in.) DN OD
Corresponding pipe Tapping drill size (mm)
(mm)
OD
(in.)
Thickness
(mm)
BSP. F (G)
TruVision Dome Brackets Installation Manual 15
indoor use
Suitable for outdoor /
PMA
TVD-M-
TVD-
TVD-
Outdoor
CB5A
CB5
Indoor
Outdoor
Outdoor
Outdoor
Indoor
Outdoor
Indoor
Outdoor
Outdoor
Outdoor
Outdoor
Outdoor
Outdoor
Outdoor
Outdoor
Outdoor
Outdoor
Outdoor
Outdoor
TVD-SNB
CB3
TVD-
M2-
TVD-
TVD-
CB2 &
WEBM
TVD-
CB5A
CB5
TVD-
TVD-PPB TVD-M-PMA
Wall-mount Pendant/ceiling-mount Pole-mount
TVD-SNB
TVD-
TVD-
TVD-
CB2 &
M2-
TVD-
TVD-
WEBM
M2-WM
TVD-
TVD-
TVD-
CB3
M2-
WEBM
CB5A
CB5
CB3
M2-
TVD-
TVD-
CB2 &
WEBM
Flush-
mount

Overview: Fixed dome cameras by bracket

Bracket to use
TVD-M2-
Class Camera SKU
FM
Analog TVD-2101
Analog TVD-4102
Analog TVD-5110-3-N(P)
Analog TVD-5125TE-3-N(P)
Analog TVD-6120VE-2-N(P)
Analog TVD-6125VE-2-N(P)
Analog TVD-DOME5-HR9-N(P)
Analog TVD-DOME6-HR-N(P)
Analog TVD-TIR6-HR-N(P)
Analog TVD-TIR6-MR-N(P)
Analog TVD-TIR6-SR-N(P)
Analog UVD-6120VE-N(P)
Analog UVD-6120VE-2-N(P)
Analog UVD-6130VE-2-N(P)
Analog UVD-XP4DNR-VA2-N(P)
IP TVD-1103
Analog UVD-XP4DNR-VA9-N(P)
IP TVD-3103
IP TVD-1104
IP TVD-3104
16 TruVision Dome Brackets Installation Manual
Indoor
CB5A
CB5
CB3
TVD-
M2-
Outdoor
M2-
WEBM
WEBM
indoor use
Suitable for outdoor /
PMA
TVD-M-
TVD-
TVD-
TVD-SNB
TVD-
TVD-
CB2 &
TVD-
CB5A
CB5
TVD-
TVD-PPB TVD-M-PMA
TVD-
CB2 &
TVD-
TVD-
CB3
Indoor
Indoor
Outdoor
Flush-mount included
Indoor
Indoor
Indoor
Outdoor
Outdoor
Indoor
Indoor
Outdoor
Outdoor
Indoor
Outdoor
Flush-mount included
Outdoor
Outdoor
M2-
TVD-
WEBM
TVD-
M2-WM
TVD-
CB5A
Wall-mount Pendant/ceiling-mount Pole-mount
TVD-SNB
Flush-
mount
TVD-
CB2 &
TVD-
TVD-
TVD-
TVD-M2-
CB5
CB3
FM
M2-
WEBM
IP TVD-M1210W-2-N(P)
IP TVD-M1210V-2-N(P)
IP TVD-M1225V-2-N(P)
IP TVD-M1245E-2M-N(P)
IP TVD-M2210V-2-N(P)
IP TVD-M2210W-4-N(P)
IP TVD-M2225V-2-N(P)
IP TVD-M3210V-2-N(P)
IP TVD-M3225V-2-N(P)
IP TVD-M3245E-2M-N(P)
IP TVD-M5225E-3M-N(P)
IP TVD-M5225V-4-N(P)
IP TVD-N210V-2-N(P)
IP TVD-N210W-4-N(P)
IP TVD-N225E-2M-N(P)
IP TVD-N245V-2-N(P)
IP UVD-IP-XP4DNR-VA2-N(P)
Class Camera SKU
IP UVD-IP-XP4DNR-VA9-N(P)
TruVision Dome Brackets Installation Manual 17
Loading...