U.S.
T 855 536 3573
F 561 998 6224
Asia
T 65 6424 7932
F 65 6424 7978
Australia
T 61 3 9239 1200
F 61 3 9239 1299
Canada
T 800 267 6317
F 613 737 5517
EMEA
T 48 58 326 22 40
F 48 58 326 22 41
Latin America
T 503 589 8614
F 561 994 6572
www.utcfireandsecurity.com
© 2012 UTC Fire & Security. All rights reserved.
UTC Fire & Security, 9 Farm Springs Road,
Farmington, CT 06034-4065, USA
Transition Series
Multi-technology Access Readers
Description
Transition™ 500-PIV Series multi-technology card
readers feature simultaneous compatibility with multivendor 125 kHz Proximity and PIV (ISO 14443A)
credential technologies—all in one reader. With this
remarkable technology combination, security
administrators can now deploy the Transition readers into
new or existing facilities.
Figure 1. Multi-technology Readers
Mounting the reader
All models of the T-500-PIV series readers can be
mounted using a U.S. single-gang electrical box or
directly to a wall.
1. Find a suitable mounting position on the door frame
or wall.
Note: For out of doors or wet locations, it is recommended
that the gasket provided be installed on the base as shown in
Figure 5.
2. If mounting directly to the wall, use one of the
following methods:
2a. Drill two vertical mounting holes from 3.25”
(83 cm) to 4.891” (125 cm) apart on the mounting
surface of the door frame or wall.
Figure 2. Direct wall mounting
2b. Models 520/525-PIV can be mounted using a
second pair of vertical mounting holes,
horizontally spaced 2.75” (70 cm) from the first
pair.
Figure 3. T520/525-PIV Direct wall mounting alternative
3. Drill one 0.625” (15.87 mm) diameter hole in wall for
the pigtail wire connection.
4. Follow the Cable Connection Chart to connect the
reader to the field panel and external door
equipment.
5. Mount the base plate to the wall using the supplied
screws.
6. Install gasket if required, see Figure 5.
7. Install the top cover to the reader base. The
base plate and top cover guides should be
aligned, so the connectors seat correctly.
Figure 4. Aligning base plate and top cover
8. Verify the connection is secure and install the
security screws on the top and bottom of the
reader.
9. Cover the exposed screws with the rubber
plugs provided.
Figure 5. Gasket detail
Connecting the cable
1. The readers are supplied with a 12-conductor
cable pigtail with drain wire. Connect the pigtail
to the host panel. Use the Cable Connection
Chart (below) to correctly match the color of
each wire.
Color Signal
Red 6 to 16 VDC
Black Ground
Green Data 0
White Data 1
Orange Green LED Control
Brown Red LED Control
Yellow Beeper Control
Gray Door DI
Pink REX DI
Tan Tamper Output
Blue Hold
Purple Reserved
........ Drain Wire
2. Use a DC Power source between 6-16 VDC.
3. Verify the reader is properly grounded by
attaching the ground wire to an earth ground
connection at the power supply or field panel
end of the cable. Connect reader’s drain wire
to the cable shield. Connect shield wires at the
field panel.
Testing the reader
1. Power up the reader. Verify the power-on self
test LED/beep sequence:
- green LED flashes; two short beeps
- yellow LED flashes; three short beeps
- red LED flashes.
- yellow LED flashes.
2. Verify the yellow LED is on continously
indicating the reader is ready.
3. Present a badge that has been properly
enrolled in the system. Verify the yellow LED
flashes and a short beep is heard.
Removing the cover
1. Remove all security screws.
2. Pull cover off the base. Refer to Figure 4 on
page 2.
Keypad configuration card
1. Place the reader in tamper mode by briefly
removing and replacing the reader’s cover
while the power is on. The reader stays in
tamper mode for 60 seconds (minimum) after
power is applied or the cover is replaced.
2. Present the keypad configuration card within
one minute. The LED turns green and a short
triple-beep indicates the reader is ready to
configure.
3. Enter the keypad entry within five seconds.
Use the chart below to identify the correct
keypad entry.
non-
Mode/Keypad entry Setting UTC
1 * followed by 0
(Factory default
setting)
2 * followed by 1 6 bits per key,
3 # followed by
3 keys
(0 to 9 only)
4 1 followed by 1
key (0 to 9 only)
5 1 followed by * 4 bits per key, no parity,
6 1 followed by # 4 bits per key, no parity,
For non-ITC keypad configurations, contact Sales
Engineering/Pre-Sales Support for assistance.
8 bits per key,
no buffering
no buffering
26-bits output custom
configuration. (Contact
Sales Engineering/PreSales Support for
assistance)
4 bits per key, no parity,
up to 9 keys buffered
up to 10 keys buffered
up to 11 keys buffered
UTC
FCC compliance
The FCC requires the following statement: This
reader uses radio frequency energy and has been
tested, and complies with the limits of FCC testing.
Changes, modification, or disregard of proper
installation and instructions not expressly approved
by UTC Fire & Security, and is strictly prohibited by
the FCC and could void the user’s authority to
operate the equipment.
Specifications
Colors Black
Power supply Linear DC recommended
Power usage T-500-PIV: 210 mA @ 12 VDC
T-520-PIV: 130 mA @ 12 VDC
T-525-PIV: 130 mA @ 12 VDC
Voltage range 6 —16 VDC
Temperature
a
range
Cable distance to
panel
Read Range
(Distances may
vary depending on
environment.)
Wiegand output Proximity 4002 (40-bit)
Tamper output Open Collector
Regulatory
approvals and
standards
ISO Standards ISO 14443A, B
UL evaluation for UL Listed Installations:
a. -25
b. Model T-500-PIV, T-520-PIV and T-525-PIV
Proximity and HID Proximity up to 4.5" (11.43 cm)
c. Power consumption:
d. Request to exit terminals on the reader are not to
be connected in UL listed installations.
b
o
F to 125oF (-32oC to 52oC)
Model 500-PIV: 210 mA @ 12 VDC
Model 520-PIV and 525-PIV: 130 mA @ 12 VDC
-31oF to +149oF (-35oC to +65oC)
Up to 500 ft. (152.4 m) @ 12 VDC with
20 AWG shielded cable
Proximity Perfect and Ultralight cards
are not supported by the Transition
Series reader.
Model T-500-PIV:
- Proximity: up to 3.5" (8.89 cm)
- HID Proximity: up to 3.5" (8.89 cm)
- PIV: up to 1" (2.54 cm)
Model T-520-PIV and T-525-PIV:
- Proximity: up to 5" (15.24 cm)
- HID Proximity: up to 5" (15.24 cm)
- PIV: up to 1" (2.54 cm)
HID Proximity (depends on card
format)
PIV (75-bit and 200-bit)
UL 294, CE, and FCC (part 15)
The voltage specification for this reader is 6—16
VDC, although 12 VDC or greater is recommended
for better performance and cable run distances.
Ordering information
Product Part Number
T-500-PIV (Black; Mullion mount; Wiegand
output) *
T-520-PIV (Black; 1-Gang US mount;
Wiegand output) *
T-525-PIV (Black; 1-Gang US mount;
Keypad; Wiegand output) *
* Installation wrench (Required) 385001001
Copyright © 2012, UTC Fire & Security. All Rights Reserved.
The Transition Series product name and logo are trademarks of
UTC Fire & Security. Other trade names used in this document
may be trademarks or registered trademarks of the
manufacturers or vendors of the respective products.
Document number: 460661001G - November 2012
430212006
430213006
430214006
Loading...