Interlogix T-100 User Manual

TruPortal™ Series

front view

side

view

1.75”

[44.5mm]

1.0”

[

25.4mm]

4.20

[106.7mm]

T-100 Model Reader

Technical support

For assistance with this product, refer to this document and any other documentation provided. If you still have questions, you may contact technical support during normal business hours (Monday through Friday, excluding holidays, between 8 a.m. and 8 p.m. Eastern Standard Time.) See http://www.interlogix.com/customer-support.

U.S. 1-855-286-8889, option 2 Canada 1-855-286-8889, option 2 Latin America 1-561-998-6114

Web site: http://www.interlogix.com

Interlogix 3211 Progress Drive, Lincolnton, NC 28092, USA

Description

The T-100 card reader is a card serial number reader compatible with the following 125 kHz Proximity technologies:

• CASI ProxLite®

•HID

Proximity

Mounting the reader

1. Find a suitable mounting position on the door frame or wall.

2. Drill two vertical mounting holes 2.25” (57.2 mm) apart on the mounting surface of the door frame or wall.

Figure 1. Dimensions

3. Drill one 1.00” (25.4 mm) diameter hole in wall for the pigtail wire connection.

4. Follow the Cable Connection Chart to connect the reader to the field panel.

5. Mount the base plate to the wall using the supplied screws.

6. Hook the top of the reader case to the top of the base plate and press into place.

Figure 2. Base plate, reader case, and top cover

7. Install the supplied screw in the base of the reader.

8. Snap the cover on the top of the case.

Connecting the cable

1. The readers are supplied with an 8-conductor cable pigtail with drain wire. Connect the pigtail to the host panel. Use the Cable Connection Chart (below) to correctly match the color of each wire.

Color Signal

Black Ground

Blue Beeper

Brown Red LED Control

Green Data 0

Orange Green LED Control

Red 5 to 16 VDC

White Data 1

Drain Shield Ground

2. Use a DC power source between 5-16 VDC.

3. Connect the reader’s drain wire to the cable shield. Connect shield wires at the field panel.

Testing the reader

Cable Distance Max. @ 12 VDC AWG

200 ft. (60.96 m) 22

300 ft. (91.44 m) 20

500 ft. (152.4 m) 18

1. Power up the reader. Verify the power-on self test LED/beep sequence:

- green LED flashes; two short beeps

- yellow LED flashes; three short beeps

- red LED flashes

- yellow LED flashes

2. Verify the yellow LED lights indicating the reader is ready.

3. Present a badge that has been properly enrolled in the system. Verify the green LED lights and a short beep is heard.

Removing the cover

To remove the cover, squeeze the sides of the top cover and pull to release the cover.

The voltage specification for this reader is 5-16 VDC, although 12 VDC or greater is recommended for better performance and cable run distances.

The recommended cable gauge is 18-gauge to 22gauge. Check with the cable supplier to determine the best choice for the application and installation distance.

FCC compliance

The FCC requires the following statement: This reader uses radio frequency energy, has been tested, and complies with the limits of FCC testing. Changes, modifications, or disregard of proper installation and instructions not expressly approved by UTC Fire & Security are strictly prohibited by the FCC and could void the user’s authority to operate the equipment.

Specifications

Colors Black, Charcoal, Gray

Power supply Linear DC recommended

Power usage 70 mA @ 12 VDC

Voltage range 5 - 16 VDC

Temperature

range

Cable distance to

panel

Read Range

(Distances may vary depending on environment.)

Wiegand

output

Regulatory approvals and standards

UL evaluation for UL Listed Installations:

a. -25°F to 125°F (32°C to 52°C) b. 500 ft. (152.4 m) max. 22 AWG @ 12 VDC

200 ft. (60.96 m) max. 22 AWG @ 5 VDC

c. Proximity: up to 3.0" (7.62 cm)

HID Proximity: up to 3.0" (7.62 cm)

d. HID Proximity/Corporate 1000: Most formats (up to

64-bit)

-31°F to 149°F (-35°C to 65°C)

Proximity Perfect cards are not supported by the TruPortal Series reader.

- CASI ProxLite: up to 3.5" (8.89 cm)

- HID Proximity: up to 3.5" (8.89 cm)

- Proximity: 4002 (40-bit) 12 digits

- HID Proximity/Corporate 1000: Most formats (26 to 174-bit)

UL 294, CE, and FCC Part 15

Ordering information

Product Part numbers

T-100 (3 covers, 18" / 45.7 cm pigtail wire)

T-100 (3 covers, 84" / 214 cm pigtail wire)

Note: Each part number includes all three colors of the cover plates (black, charcoal, gray).

The TruPortal product name and logo are trademarks of United Technologies. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.

Document number: 460949002C - July 2013

TP-RDR-100a

TP-RDR-100b