Interlogix NS3552-8P-2S-V2 Specsheet

Network Transmission
NS3552-8P-2S-V2 NS3552-16P-2T-2S NS3553-4P-1T-2S
Industrial Gigabit PoE+ / PoE-Ultra Managed Switches
OVERVIEW
The IFS® Industrial Gigabit PoE+ Managed Switches by Interlogix are fully managed Layer 2 switches providing an industrial hardened design. This design provides for operational recovery in the event of a network or power system failure.
®
The IFS NS3552-16P-2T-2S is an Industrial Gigabit PoE+ Managed Switch equipped with sixteen 10/100/1000Mbps RJ45 ports with PoE+ (30w) capabilities and two Gigabit RJ45/SFP (fiber) uplink ports.
The IFS NS3553-4P-1T-2S is an Industrial Gigabit PoE+ Managed Switch equipped with four 10/100/1000Mbps RJ45 ports with PoE-Ultra (60w), one 10/100/1000Mbps RJ45 ports and two Gigabit RJ45/SFP (fiber) uplink ports.
Layer 2 Managed Switch
The IFS Industrial Gigabit PoE+ Managed Switch Series supports advanced features including IEEE 802.1Q VLAN, GVRP, port link aggregation, QoS, broadcast storm control and MAC address filtering. The series also includes IGMP snooping and querying multicasting for media operations and bandwidth utilization to fit a variety of applications. Via aggregation of supporting ports, the series allows the operation of high-speed trunk operation combining multiple ports. A maximum of four ports can be assigned for four trunk groups and support fail-over as well. Additionally, the IFS Industrial Gigabit PoE+ Managed Switch Series is compatible with equipment from other vendors that meet IEEE 802.3 standards.
NS3552-8P-2S-V2 is an Industrial Gigabit PoE+ Managed
NS3552-8P-2S-V2
8+2 Industrial Gigabit PoE+ Managed Switch
Industrial-grade Network Redundancy and Recovery
These switches not only incorporate the industry standard Rapid Spanning Tree Protocol (IEEE 802.1w RSTP), but also an advanced rapid ring recovery protocol allowing improved network recovery times that are on average less than 20ms for redundant ring topologies. The switches incorporate a redundant power supply system to further enhance network reliability and uptime. Ideal for use in implementing highly fault-tolerant ring and mesh network architectures, these switches are suited for environments such as industrial security, factory automation and intelligent transportation systems (ITS).
Robust Hardened Design
With an IP-30 rated enclosure, IFS Industrial Gigabit PoE+ Managed Switches provide protection against electromagnetic (EMI) and radio­frequency (RFI) interference typically found in industrial environments. This series of switches comply with IEC60068-2-xx standards for free-fall, shock, and vibration and operate in -40°C~75°C temperatures found in difficult environments such as plant floors or in curbside traffic control cabinets.
Management in TruVision
The NS3552-8P-2S-V2 and NS3553-4P-1T-2S simplifies management of your IP video system by providing integration into TruVision Navigator 8.0 and above. The NS3552-8P-2S-V2 and NS3553-4P-1T-2S can provide information to TruVision Navigator such as ONVIF labels of cameras, bandwidth usage per port and POE power control making installation and management IP Video systems simpler and effortless.
NS3552-16P-2T-2S
16+2 Industrial Gigabit PoE+ Managed Switch
®
Navigator
NS3553-4P-1T-2S
4+1+2 Industrial Gigabit PoE-Ultra Managed Switch
interlogix.com/ifs
STANDARD FE ATURES
Physical Ports
• RJ45 with Auto MDI/MDI-X and Auto-negotiation
• SFP 100/1000Base-X
• 1 RJ-45 console port
NS3552-8P-2S-V2
• 8-port 10/100/1000Base-T with PoE+ and 2-ports SFP (fiber) 100/1000Base-X
NS3552-16P-2T-2S
• 16-port 10/100/1000Base-T with PoE+ Plus 2-ports SFP (fiber) and 2-ports RJ45 10/100/1000Base-T
NS3553-4P-1T-2S
• 4-port 10/100/1000Base-T with PoE-Ultra Plus 2-ports SFP (fiber) and 1-port RJ45 10/100/1000Base-T
Power over Ethernet
• Complies with IEEE 802.3af / IEEE 802.3at Power over Ethernet / End-Span PSE
• IEEE 802.3af / 802.3at / PoE-Ultra (NS3553-4P-1T-2S) devices powered
• Supports PoE Power up to 30.8 Watts for each PoE ports (up to 60W NS3553-4P-1T-2S)
• Auto detect powered device (PD)
• Circuit protection helps reduce power interference between ports
• Remote power feeding up to 100m
• PoE Management features
• IEEE 802.3af and IEEE 802.3at mode switch control
• Total PoE power budget control
• Per port PoE function enable/disable
• PoE Admin-mode control
• PoE Port Power feeding priority
• Per PoE port power limit
• PD classification detection
• Temperature Threshold Control
• PoE Usage Threshold Control
• PD Alive check/reboot
• PoE schedule
Robust Hardened Design
• IP30 Aluminum metal case protection
• DIN-rail and Wall Mount Design
• 48V DC, redundant power with polarity reverse protect function
• Supports EFT protection 6000VDC for power line
• Supports 6000VDC Ethernet ESD protection
• -40°C~75°C operating temperature
Digital Input/Digital Output
• 2 Digital Input (DI)
• 2 Digital Output (DO)
• Integrate sensors into auto alarm system
• Transfer alarm to IP network via email and SNNP trap
Layer 2 Features
• Prevents packet loss with back pressure (Half-Duplex) and IEEE 802.3x PAUSE frame flow control (Full-Duplex)
• Store-and-Forward architecture and runt/CRC filtering
• Storm Control support
• Broadcast / Multicast / Unicast
• Supports VLAN
• IEEE 802.1Q Tagged VLAN
• Up to 255 VLANs groups, out of 4094 VLAN IDs
• Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
• Private VLAN Edge (PVE)
• Protocol-Based VLAN
• MAC-Based VLAN
• Voice VLAN
• Supports Spanning Tree Protocol
• STP, IEEE 802.1D Spanning Tree Protocol
• RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
• MSTP, IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN
• BPDU Guard
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (Static Trunk)
• Maximum 5 trunk groups, up to 8 ports per trunk group (NS3552-8P-2S-V2)
• Maximum 10 trunk groups, up to 8 ports per trunk group (NS3552-16P-2T-2S)
• Up to 16Gbps bandwidth (Duplex Mode)
• Provides Port Mirror (1-to-1)
• Port Mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to reduce the possiblity of broadcast loops
Quality of Service
• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
• IEEE 802.1p CoS
• IP TOS / DSCP / IP Precedence
• IP TCP/UDP port number
• Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing policies on the switch port
• DSCP remarking
Multicast
• Supports IGMP Snooping v1, v2 and v3
• Supports MLD Snooping v1 and v2
• Querier mode support
• IGMP Snooping port filtering
• MLD Snooping port filtering
• MVR (Multicast VLAN Registration)
Security
• IEEE 802.1x Port-Based / MAC-Based network access authentication
• Built-in RADIUS client to co-operate with the RADIUS servers
• TACACS+ login users access authentication
• RADIUS / TACACS+ users access authentication
• IP-Based Access Control List (ACL)
• MAC-Based Access Control List
• Source MAC / IP address binding
• DHCP Snooping to filter untrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard helps minimize IP spoofing attacks
• Auto DoS rule to help defend DoS attack
• IP address access management
Switch Management
• Support for TruVision
• Switch Management Interfaces
• Console / Telnet Command Line Interface
• Web switch management
• SNMP v1 and v2c switch management
• SSH / SSL and SNMP v3 secure access
• Four RMON groups (history, statistics, alarms, and events)
IPv6 IP Address / NTP / DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• Firmware upload / download via HTTP / TFTP
• DHCP Relay
• DHCP Option 82
• User Privilege levels control
• NTP (Network Time Protocol)
• Link Layer Discovery Protocol (LLDP) Protocol
• Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues (NS3552-8P-2S-V2 and NS3553-4P-1T-2S Only)
• Reset button for system reboot or reset to factory default
®
Navigator 8.0 and above
Dimensional Diagrams
1.57 in.
1.96 in.
NS3552-8P-2S-V2
Console
P1 P2
FAULT
Ring R.O.
115200,N,8,1
LNK
9
10
ACT
LNK/ACT1000LNK/ACT1000
9
10
100/1000X SFP
ACTLNK
RESET
PoE In-Use
8
7
6
5
4
3
2
1
10/100/1000T
NS3552-8P-2S-V2
2.83 in.
(72mm)
802.3at PoE
NS 3552-16 P-2T-2S
RESET
802.3at PoE+
P1 P2
FAULT
Ring
ACTLNK
2
4
6
8
10
12
14
16
NS3552-16P-2T-2S
3.23 in. (82mm)
Console
R.O.
17
18
ACT10/100 LNK ACT1000 LNK
19
20
1
3
5
7
9
11
13
15
PoE In-use
.90 in.
(23mm)
3.07 in. (78mm)
4.21 in.
(107mm)
3.98 in.
(101mm)
4.21 in.
(107mm)
.36 in. (9.2mm)
(136mm)
4.21 in.
(Ø3.5-4mm)
.36 in. (9.2mm)
.35 in. (9mm)
(50mm)
.70 in.
(18mm)
(40mm)
(28mm)
1.57 in.
1.10 in.
0.99 in.
(25.2mm)
(152mm)
5.98 in.
0.92 in.
(23.6mm)
2.59 in. (66mm)
1.96 in.
(50mm)
(40mm)
(152mm)
5.98 in.
(28mm)
1.10 in.
NS3553-4P-1T-2S
2.83 in. (72mm)
.90 in.
(23mm)
3.07 in.
(78mm)
4.21 in.
(107mm)
.36 in. (9.2mm)
(136mm)
4.21 in.
(Ø3.5-4mm)
(152mm)
5.98 in.
(25.2mm)
(23.6mm)
99 in.
92 in.
1.96 in. (50mm)
.70 in.
(18mm)
2.59 in. (66mm)
(40mm)
(28mm)
1.57 in.
1.10 in.
Industrial Gigabit Managed Switch Specifications
PART NO. NS3552-8P-2S-V2 NS3552-16P-2T-2S NS3553-4P-1T-2S
10/100/1000Base-T Ports RJ-45 (8) RJ-45 (16) RJ-45 (4)
10/100/1000Base-T Ports -- RJ-45 (2) RJ-45 (1)
100/1000Base-X SFP Ports SFP Ports (2)
Port Configuration Auto MDI/MDI-X
Port Speed Auto-negotiate
Electro Static Discharge
Physical Ports
(ESD) Protection
Console Port RJ-45 (1)
Switch Architecture Store-and-Forward
Switch Fabric 20Gbps/non-blocking 40Gbps/non-blocking 14Gbps/non-blocking
Throughput (Packet per second) 14.8Mpps @64Bytes 29.7Mpps @64Bytes 10.42Mpps @64Bytes
Address Table 8K entries
Share Data Buffer 4Mbit
Maximum Frame Size 9K Bytes (Jumbo Frames)
Flow Control Back pressure for Half-Duplex
Switch Performance
Port Configuration Port disable/enable, Auto-negotiation 10/1000/1000Mbps full and half-duplex mode selection, Flow control
Port Status Display each port’s speed Auto negotiation status, duplex mode, link status, Flow control status
Bandwidth Control Bandwidth control per port: Ingress: 500Kb~1000Mbps, Egress: 500Kb~1000Mbps
Spanning Tree IEEE 802.1d Spanning Tree, IEEE 802.1w Rapid Spanning Tree, IEEE 802.1s Multiple spanning tree protocol
VLAN 802.1Q Tagged Based VLAN, up to 255 VLAN groups
Multicast IGMP (v1/v2/v3) Snooping, up to 255 multicast Groups
QoS Traffic classification based, Strict priority and WRR 8-Level priority for switching
Layer 2
Port Mirroring RX / TX / Both
Security IEEE 802.1x Port-Based / MAC-Based network access authentication. RADIUS / TACACS+ users access
SMNP MIBs RFC-1213 MIB-II, IF-MIB, RFC-1493 Bridge MIB, RFC-1643 Ethernet MIB, RFC-2863 Interface MIB,
Link Aggregation EEE 802.3ad LACP / Static Trunk;
Management Interface Console, Telenet, Web Browser, SNMP v1, v2c and v3
6K VDC
IEEE 802.3x Pause Frame for Full-Duplex
disable/enable and bandwidth control on each port
Q-in-Q tunneling Private VLAN Edge (PVE) MAC-Based VLAN Protocol-Based VLAN Voice VLAN MVR (Multicast VLAN Registration) Up to 255 VLAN groups, out of 4094 VLAN IDs
IGMP Querier mode support MLD (v1/v2) Snooping, up to 255 multicast Groups MLD Querier mode support
- Port Number
- 802.1p priority
- 802.1Q VLAN tag
- DSCP/TOS field in IP Packet
authentication. IP-Based Access Control List (ACL). MAC-Based Access Control List. Source MAC / IP address binding. DHCP Snooping. Dynamic ARP Inspection. IP Source Guard helps prevent IP spoofing attacks. Auto DoS rule to help defend DoS attack. IP address access management
RFC-2665 Ether-Like MIB, RFC-2819 RMON MIB (Group 1, 2, 3 and 9), RFC-2737 Entity MIB, RFC-2618 RADIUS Client MIB, RFC-2933 IGMP-STD-MIB, RFC3411 SNMP-Frameworks-MIB, IEEE 802.1X PAE, LLDP, MAU-MIB
5 groups of 8-port trunks
IEEE 802.3ad LACP / Static Trunk; 10 groups of 8-port trunks
IEEE 802.3ad LACP / Static Trunk; 3 groups of 3-port trunks
PART NO. NS3552-8P-2S-V2 NS3552-16P-2T-2S NS3553-4P-1T-2S
IEEE PoE Standard IEEE 802.3af/IEEE 802.3at Power over Ethernet/PSE IEEE 802.3af/IEEE 802.3at/Ultra
PoE PSE
Maximum Devices 8 16
Output Power (per-port) Per Port 56VDC, 350mA max. 15.4 watts (IEEE 802.3af)
Per Port 56VDC, 590mA max. 30 watts (IEEE 802.3at)
Power over
Ethernet PoE)
PoE Pin Assignment 1/2(+), 3/6(-) End Span Mode: 1/2(+), 3/6(-)
System Power 1 (green), Power 2 (green), Fault Alarm (green), Ring (green), Ring Owner (green)
Per Port 52 to 56VDC, 350mA max. 15.4 watts (IEEE 802.3af) Per Port 52 to 56VDC, 590mA max. 30 watts (IEEE 802.3at) Per Port 52 to 56VDC, 590mA max. 72 watts (Ultra-PoE)
Mid Span Mode: 4/5 (+), 7/8(-) PoE-Ultra Mode: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
10/100/1000Mbps Ports PoE In-Use (orange),
LNK/ACT (green)
Indicators
LED Status
SFP GigE Uplink Ports 1000 (orange),
LNK/ACT (green)
Power Input 1 (Primary Power) 48VDC 48VDC to 56VDC 52VDC to 56VDC
Power Input 2 (Primary Power) 48VDC 48VDC to 56VDC 52VDC to 56VDC
Electrical Fast Transient (EFT) Protection
Power and Alarm Fault Connector
Alarm Fault Relay 1A @ 24VDC
Enclosure IP-30 Metal Case
Mounting DIN-rail or wall-mount
Electrical & Mechanical
Dimensions (in/cm) (W x D x H) 6 x 4.21 x 2.83 in.
Weight (lbs/g) 3.31 lbs., 1.5kg 3.75 lbs., 1.7kg 2.31 lbs., 1.05kg
Operating Temperature -40ºC~-75ºC
Storage Temperature -40ºC~-85ºC
mental
Relative Humidity 5%~95% (non-condensing)
Environ-
Regulatory Standards FCC Part 15 Class A, CE
IEEE/RFC Standards IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX/100Base-FX, IEEE 802.3z Gigabit SX/LX,
IEC Standards IEC60068-2-32 (Free fall)
Standards Compliance
6KV DC
6-pin removable screw terminal
6 x 4.21 x 3.31 in.
(152 x 107 x 72mm)
IEEE 802.3ab Gigabit 1000T, IEEE 802.3x Flow Control and Back Pressure, IEEE 802.1d Spanning Tree Protocol, IEEE 802.1w Rapid Spanning Tree Protocol, IEEE 802.1p Class of Service, IEEE 802.1Q VLAN Tagging, IEEE 802.1x Port Authentication Network Control, IEEE 802.3af Power over Ethernet, RFC 768 UDP, RFC 793 TFTP, RFC 791 IP, RFC 792 ICMP, RFC 2068 HTTP, RFC 1112 IGMP Version 1, RFC 2236 IGMP Version 2
IEC60068-2-27 (Shock) IEC60068-2-6 (Vibration)
(152 x 107 x 84mm)
PoE-Ultra in use (green), PoE-af/at in use (orange), 100 LNK/ACT (orange), 1000 LNK/ACT (green
100 LNK/ACT (orange), 1000LNK/ACT (green)
NS3552-8P-2S-V2 NS3552-16P-2T-2S NS3553-4P-1T-2S
Industrial Gigabit PoE+ / PoE-Ultra Managed Switches
Typical Application
Ring Master
Primary Path Primary Path
Industrial Fail-Safe
(IFS) Ring
Average Network
Recovery Time <20ms.
Backup Path
Link
Failure
NVR
Backup Path
NS3552-8P-2S-V2 and NS3553-4P-1T-2S only.
Truvision® Navigator works with
Ordering Information
NS3552-8P-2S-V2
NS3552-16P-2T-2S
NS3553-4P-1T-2S
Included Accessories
Note: These switches require a Small Form-factor Pluggable (SFP) for optical uplink use. IFS SFPs are available for multi-mode, single mode, and 1 or 2 fibers for various transmission distances over optical fiber. Please refer to the IFS SFP data sheet to select the appropriate SFP for your particular application needs. IFS S25 or S35 Series SFPs are recommended.
Note: External power supply must be purchased separately.
8-Port Industrial Gigabit PoE+ Managed Switch (Wide Operating Temp. -40 to 75ºC)
16-Port Industrial Gigabit PoE+ Managed Switch (Wide Operating Temp. -40 to 75ºC)
4-Port Industrial Gigabit PoE-Ultra Managed Switch (Wide Operating Temp. -40 to 75ºC)
User’s Manual, DIN-rail Kit, Wall Mount Kit
Accessories
SFP
SFP
SFP
SFP
PS48VDC480W-DIN
S30 Series
S35 Series (wide-temp)
S20 Series
S25 Series (wide-temp)
48VDC Industrial 480W DIN-rail Power Supply
interlogix.com
Specifications subject to change without notice.
© 2018 United Technologies Corporation.
All rights reser ved.
All trademarks are the property of their respective owners.
Interlogix is par t of UTC Climate, Controls & Securit y,
a unit of United Technologies Corporation.
2018/11 (GSP-2641)
Loading...