IFS NS3502-8P-2S
Quick Installation Guide
P/N 1072677 • REV A • ISS 19DEC13
Copyright © 2013 United Technologies Corporation
r
Interlogix is part of UTC Climate Controls &
Security, a unit of United Technologies
Corporation. All rights reserved.
Trademarks and
patents
The IFS NS3502-8P-2S name and logo are
trademarks of United Technologies.
Other trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacture
Interlogix
3211 Progress Drive, Lincolnton, NC 28092 USA
Authorized EU manufacturing representative:
UTC Climate Controls & Security B.V.,
Kelvinstraat 7, 6003 DH Weert, Netherlands
Version This document applies to IFS NS3502-8P-2S
version 1.0.
Certification
N4131
FCC compliance Class A: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.
ACMA
compliance
Notice! This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
Canada This Class A digital apparatus complies with
European Union
directives
Canadian ICES-003.
Cet appareil numérique de la classe A est
conforme á la norme NMB-003du Canada.
2004/108/EC (EMC directive): Hereby, UTC Fire
& Security declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
Contact
information
For contact information, see
www.utcfssecurityproducts.eu.
or
www.interlogix.com
Content
1. Package Content 1
2. Requirements 2
3. Terminal Setup 3
4. Logon to the Console 5
5. Configure IP Address 6
6. Start Web Management 8
7. Resetting to Factory Default 11
IFS NS3502-8P-2S Quick Installation Guide i
1. Package Content
Thank you for purchasing IFS Layer 2 Managed Switch, NS3502-8P-2S. Terms of
“Managed Switch” means the Switch mentioned titled in the cover page of this
Quick Installation Guide.
Open the box of the Managed Switch and carefully unpack it. The box should
contain the following items:
The NS3502-8P-2S x1
This Quick Installation Guide x1
User's Manual CD x1
RS232 DB9 Female Console Cable x1
Rubber Feet x 4
Two Rack-mounting brackets with attachment screws x1
Power Cord x1
SFP Dust Caps x 2
If any item is found missing or damaged, please contact your local reseller for
replacement.
IFS NS3502-8P-2S Quick Installation Guide 1
2. Requirements
The Managed Switch provide remote login interface for manage; the following
equipments are necessary for further management
Workstation installed with Ethernet NIC (Network Card)
Workstations of subscribers running Windows XP/2003, Vista, Windows 7, MAC
OS X, Linux, Fedora, Ubuntu or other platform compatible with TCP/IP protocols.
Ethernet Port connect
¾ Network cables - Use standard network (UTP) cables with RJ-45
connectors.
¾ Above Workstation installed with WEB Browser and JAVA runtime
environment Plug-in
Serial Port connect (Terminal)
Above PC with COM Port(DB-9) or USB-to-RS-232 converter
It is recommended to use Internet Explore 7.0 or above to
access the Managed Switch.
.
2 IFS NS3502-8P-2S Quick Installation Guide
3. Terminal Setup
To configure the system, connect a serial cable to a COM port on a PC or
notebook computer and to serial (console) port of the Managed Switch. The
console port of the Managed Switch is DCE already, so that you can connect the
console port directly through PC without the need of Null Modem.
Figure 3-1: NS3502-8P-2S Console Connection
A terminal program is required to make the software connection to the Managed
Switch. Windows' Hyper Terminal program may be a good choice. The Hyper
Terminal can be accessed from the Start menu.
1. Click START, then Programs, Accessories and then Hyper Terminal.
2. When the following screen appears, make sure that the COM port should be
configured as:
Parity : None
Data bits : 8
Stop bits : 1
Flow Control: None
Baud Rate: 115200
IFS NS3502-8P-2S Quick Installation Guide 3
Figure 3-2 : Hyper Terminal COM Port Configuration
4 IFS NS3502-8P-2S Quick Installation Guide
4. Logon to the Console
Once the terminal has connected to the device, power on the Managed Switch, the
terminal will display that it is running testing procedures.
Then, the following message asks the login user name and password. The factory
default user name and password as following and the login screen in Figure 4-1
appears.
User name: admin
Password: admin
Figure 4-1: Managed Switch Console Login Screen
1. For security reason, please change and memorize the
new password after this first setup.
2. Only accept command in lowercase letter under console
interface.
IFS NS3502-8P-2S Quick Installation Guide 5
5. Configure IP Address
The Managed Switch is shipped with default IP address as following.
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
To check the current IP address or modify a new IP address for the Managed
Switch, please use the procedures as follow:
Show the current IP address
1. On ”Switch/> ” prompt, enter “ip configuration”.
2. The screen displays the current IP address, Subnet Mask and Gateway. As
show in Figure 5-1.
Figure 5-1: Show IP Information Screen
Configure IP address
3. On “Switch/> ” prompt, enter the following command and press <Enter>. As
show in Figure 5-2.
Switch/> ip setup 192.168.1.100 255.255.255.0 192.168.1.1
The previous command would apply the follow settings for the Managed Switch.
IP: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
6 IFS NS3502-8P-2S Quick Installation Guide
Figure 5-2: Set IP Address Screen
4. Repeat Step 1 to check if the IP address is changed.
If the IP is successfully configured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of Manag ed Switch
through the new IP address.
If you do not familiar with console command or the related
parameter, enter “?” anytime in console to get the help
description.
IFS NS3502-8P-2S Quick Installation Guide 7
6. Start Web Management
The Managed Switch provides a built-in browser interface. You can manage it
remotely by having a remote host with Web browser, such as Microsoft Internet
Explorer, Mozilla Firefox, Google Chrome or Apple Safari.
Figure 6-1: IP Management Diagram
The following shows how to start up the Web Management of the Managed
Switch, please note the Managed Switch is configured through an Ethernet
connection, please make sure the manager PC must be set on the same IP subnet
address.
For example, the default IP address of the Managed Switch is 192.168.0.100, then
the manager PC should be set at 192.168.0.x (where x is a number between 1 and
254, except 100), and the default subnet mask is 255.255.255.0.
Login the Managed Switch
1. Use Internet Explorer 7.0 or above Web browser, enter IP address
http://192.168.0.100 (the factory-default IP address or that you have just
changed in console) to access the Web interface.
2. When the following dialog box appears, please enter th e d efault user n ame
“admin” and password “admin” (or the password you have changed via
console). The login screen in Figure 6-2 appears.
Default User name: admin
Default Password: admin
8 IFS NS3502-8P-2S Quick Installation Guide
Figure 6-2: Login Screen
3. After entering the password, the main screen appears as Figure 6-3.
Figure 6-3: Web Main Screen of Managed Switch
4. The Switch Menu on the left of the Web page let you access all the commands
and statistics that Managed Switch provides.
IFS NS3502-8P-2S Quick Installation Guide 9
Figure 6-4: Switch Menu
If you do not familiar with Layer 2 / Layer 4 switch functions
or the related parameter, press “Help icon” anytime in left
of the Web page to get the help description.
Now, you can use the Web management interface to continue the Switch
management or manage the Managed Switch by console interface. Please refer to
the user manual for more.
10 IFS NS3502-8P-2S Quick Installation Guide
7. Resetting to Factory Default
To reset the IP address to the default IP Address “192.168.0.100” or reset the use r
name and password to default value( default user name and password are both
admin). Press the hardware reset button at the front panel about 10 seconds.
After the device is rebooted, you can login the management WEB interface within
the same subnet of 192.168.0.xx and default user name / password. Be noted, a ll
the previous setup with disappeared after factory reset.
IFS NS3502-8P-2S Quick Installation Guide 11
Loading...