Interlogix NetworX NX-1700E Installation And Startup Manual
NX1700EIG05
(
Supercedes NX1700EIF04)
NX-1700E Proximity Card Reader
Installation and Startup
© 2012 UTC Fire & Security
All rights reserved. Printed in the United States of America.
NetworX
is a trademark of the UTC Fire & Security.
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to be met during installation,
operation, and maintenance. If further information is desired or if particular problems arise that are not covered sufficiently for the purchaser’s
purpose, the matter should be referred to UTC Fire & Security, Gladewater, Texas, USA.
This document contains proprietary information of UTC Fire & Security, USA and is furnished to its customer solely to assist that customer in the
installation, testing, operations, and/or maintenance of the equipment described. This document shall not be reproduced in whole or in part nor shall
its contents be disclosed to any third party without the written approval of UTC Fire & Security.
Please refer to the current UTC Fire & Security product catalog for detailed warranty information.
Main 800-727-2339 Technical Support 888-437-3287
Outside the US 903-845-6941 Sales & Literature 800-547-2556
Main Fax 903-845-6811 Web: www.utcfireandsecurity
.com
Symbol Legend
Warning
Indicates a procedure, practice, condition, or statement that, if not strictly observed, could result in personal
injury.
* This symbol indicates electrical warnings and cautions.
Caution
Indicates a procedure, practice, condition, or statement that, if not strictly observed, could result in damage to or
destruction of equipment or property.
** This symbol indicates general warnings and cautions.
Note
Indicates an essential or important procedure, instruction, condition, or statement.
Tip
Indicates a user tip. Provides helpful information that is not normally defined in regular use, but from an
experienced user.
Enter
Indicates a key or button should be pressed to enter data.
ORDERING INFORMATION
PART # DESCRIPTION PART # DESCRIPTION
NX-1700E
Card Reader Module
NX-216E
16 Z
one Expander Module
NX-8E
8 – 192 Z
one Control Only
NX-320E
Smart Power Supply and Buss Extender
NX-848E-KIT
NX-8E Control, NX-148E LCD Key
pad, 40VA
Transformer
NX-408E
8 Zone Wireless Expansion Module
NX-8
8 – 48 Zone Control Only
NX-416E
16 Zone Wireless Expansion Module
NX-848-KIT
NX-8 Control, NX-148E LCD Keypad, 40VA
Transformer
NX-448E
48 Zone Wireless Expansion Module
NX-6
6 – 12 Zone Control Only
NX-507E
Seven Relay Module
NX-648-KIT
NX-6 Control, NX-148E LCD Keypad, 40VA
Transformer
NX-508E
Eight Output Module
NX-148E
Alphanumeric 48 Zone LCD Keypad
NX-534E
Two-Way Listen In Module
NX-1192E
192 Zone LCD Keypad
These units are UL listed for residential use only.
NX-1700E Card Reader
2
TABLE OF CONTENTS
I. GENERAL DESCRIPTION.................................................................................................................................................... 3
II. INSTALLATION AND WIRING ............................................................................................................................................. 3
III. ENROLLING ......................................................................................................................................................................... 3
IV. ADDRESSING....................................................................................................................................................................... 3
V. PROGRAMMING................................................................................................................................................................... 4
A. USING THE LED KEYPAD............................................................................................................................................4
Entering the Program Mode........................................................................................................................................... 4
Entering the Module Address ........................................................................................................................................ 4
Programming a Location................................................................................................................................................ 4
Exiting the Program Mode:............................................................................................................................................ 5
B. USING THE LCD KEYPAD............................................................................................................................................ 5
C. PROGRAMMING DATA TYPES .................................................................................................................................... 5
VI. USER CARDS....................................................................................................................................................................... 5
Adding One User................................................................................................................................................................... 6
Adding Multiple Users with Auto-Increment........................................................................................................................... 6
Activate One User (Single User)............................................................................................................................................ 6
De-Activate One User............................................................................................................................................................ 7
Delete / Reset One User........................................................................................................................................................ 7
VII. PROGRAMMING LOCATIONS............................................................................................................................................. 7
Location 0 Programming the Scan Functions.......................................................................................................... 7
Location 241 Programming the X-10 Address for the Scan Functions......................................................................... 8
Location 242 Programming the Options and Reader Partition..................................................................................... 8
Location 243 Programming the Zones......................................................................................................................... 9
Location 244 Programming the Various Reader Timers.............................................................................................. 9
Location 245 Resetting the Reader Address ............................................................................................................... 9
Location 246 Programming the Access Options.......................................................................................................... 9
Location 247 Programming the Opening Time for Schedule 1 ...................................................................................10
Location 248 Programming the Closing Time for Schedule 1.....................................................................................10
Location 249 Programming the Days for Schedule 1..................................................................................................10
Locations 250 - 270 Programming the Schedules 2 - 8.........................................................................................................10
Location 271 Programming the Date of Holidays in January......................................................................................11
Locations 272 - 282 Programming the Date of Holidays from February to December...........................................................11
Location 283 Programming Activation Data for User Cards 1 through 120.................................................................11
Location 284 Programming Activation Data for User Cards 121 through 240.............................................................11
Location 285 Code Entry Logging Partition.................................................................................................................11
VIII. PROGRAMMING WORKSHEETS.......................................................................................................................................12
IX. GLOSSARY .........................................................................................................................................................................17
X. FCC INFORMATION............................................................................................................................................................17
XI. UNDERWRITERS LABORATORIES INFORMATION.........................................................................................................17
XII. SPECIFICATIONS................................................................................................................................................................17
I. GENERAL DESCRIPTION
The NetworX NX-1700E is a proximity card reader / door control module used to expand the capabilities of the NetworX control
panels.
$ Microprocessor-controlled
$ Includes one (1) low current trigger output, which can be used to control a door strike relay
$ Up to 15 card readers can be connected to the NetworX control panel
$ Can be programmed to control access in any or all partitions
$ LEDs can be programmed to follow the output and/or the armed or ready status of the system
$ Has an optional optical tamper switch
II. INSTALLATION AND WIRING
To install the card reader, simply wire it into the system. Refer to the following wiring table for details.
DESCRIPTION
GREEN
(DATA)
Connect to the NetworX control panel DATA terminal. This w ire is the data-signaling terminal to all
the devices on the buss.
BLACK
(COM)
Connect to the NetworX control panel COMMON terminal. Supplies the common side of the power
to the card reader module.
RED
(POS)
Connect to NetworX control panel AUX POWER + terminal. Supplies power to the card reader
module.
WHITE
(EGRESS)
This is an optional EGRESS (exit) input. To use this feature, connect the normally open egress
switch between this terminal and COM. If this feature is not used, there is no need to connect this
wire.
BLUE
(OUTPUT)
This is an optional open-collector (negative trigger) OUTPUT. It can be used to drive a relay. To
use this feature, connect the coil contacts of a relay between this terminal and AUX POWER +.
Absolute maximum 14 volts @ 25mA.
This is a low current output and must not be used to directly energize high curre nt door
openers.
III. ENROLLING
The NetworX control panels have the ability to automatically find and store in memory the presence of all keypads, zone expanders,
wireless receivers, output modules, and any other device on the keypad buss. This allows these devices to be supervised by the
control panel. To enroll the devices, enter the Program Mode using the procedure outlined in the control panel Installation Manual.
When the Program Mode is exited, the NX control panel will automatically enroll the devices. The enrolling process takes about 12
seconds, during which time the Service LED will illuminate. User codes w ill not be accepted during the enrolling process. Once a
module is enrolled, if it is not detected by the control, the Service LED will illuminate.
IV. ADDRESSING
Once the reader is wired into the system, the module needs to be addressed. Unlike most NetworX expanders,
the address of any particular reader is determined by itself after installation is complete. Follow the procedures
outlined under the section “PROGRAMMING”. When prompted to enter the module device number, a card
must
be scanned at the reader to initiate addressing (one short beep). When completed (1-2 seconds), the
reader will beep back its address (long beeps). Refer to Table IV-1 that follows for possible addresses.
Scan: To
“present” or pass
a card or FOB
within sensing
range of the card
reader module.
Ta
ble IV-1
Beeps Address Beeps Address
1 113 9 121
2 114 10 122
3 115 11 123
4 116 12 124
5 117 13 125
6 118 14 126
7 119 15 127
8 120
3
NX-1700E Card Reader
V. PROGRAMMING
A. USING THE LED KEYPAD
NOTE: The NX-108E / NX-116E / NX-124E series keypads should not be used to program user cards.
ACTION
RESULT
ENTERING THE PROGRAM MODE
Enters the Program Mode.
Stay, Chime, Exit, Bypass & Cancel LEDS will flash.
[Go To Program Code]
Factory Default is
If the "Go To Program Code" is valid, the "Service" LED will flash and
the 5 function LEDs will illuminate steady. You are now in the
Program Mode and ready to select the module address.
ENTERING THE MODULE ADDRESS
Scan a card. The card reader will address itself.
#
(example only)
Enters the module address. Refer to Table IV-1 on page 3 for the
address assigned by
the card reader module itself.
The Armed LED will illuminate while it is waiting for a programming
location to be entered.
PROGRAMMING A LOCATION
If an attempt is made to program an invalid entry for a particular segment, the keypad sounder will emit
a triple error beep (beep, beep, beep), and remain in that segment awaiting a valid entry.
To Enter a Location:
[location] #
The Armed LED will flash. If the location is valid, the "Armed" LED
will extinguish, the "Ready" LED will illuminate, and the zone LED’s
will show the data for the first segment of this location.
To Change Location Data:
[changed data]
The "Ready" LED will flash to indicate a data change in process and
will continue until the data is saved.
The new data is saved.
The keypad will increment and display the next segment’s data.
NOTE: Repeat these steps until the last segment is
reached.
To Exit a Location:
#
Exits from this location. The “Ready” LED will extinguish. The
"Armed" LED will illuminate waiting for a new pr ogramming locati on to
be entered.
To Review The Data:
[location] #
The Armed LED will flash. If the location is valid, the "Armed" LED
will extinguish, the "Ready" LED will illuminate, and the zone LED’s
will show the data for the first segment of this location.
(Do not enter data.)
The next segment is displayed. Each time is pressed, the data of
the next segment will be displayed for review.
Shortcuts:
Previous location.
Same location.
Next sequential location.
4
NX-1700E Card Reader
NX-1700E Card Reader
5
EXITING THE PROGRAM MODE:
EXIT EXIT
Exits this programming level.
B. USING THE LCD KEYPAD
All steps required for programming are the same as the aforementioned LED keypad. The LCD keypad display will prompt you for
the data required. While in the programming mode, and not in a location, the number in parenthesis is the location you were
previously changing. For example, if the display reads "Enter location, then # (5)", it is reminding you that location 5 was the last
location you programmed. In feature selection data, the numbers of the enabled features will be displayed. The features not enabled
will display a hyphen (-).
C. PROGRAMMING DATA TYPES
a) Numerical Data
Numerical data can take on values from 0-255 or 0-15 depending on the segment size.
b) Feature Selection
Feature selection data is used to turn features on or off.
VI. USER CARDS
Adding and de-activating users is done through a combination of entering information at the keypad and scanning cards. Before a
card can be entered, one reader on the system must be programmed with User Card Programming enabled (Location 242, Segment
1, Option 1, page 8).
It is recommended that only one reader on the system be enabled to modify user cards and that this reader
be located near a keypad. This reader will transfer information to all other readers in the system once
programming is finished.
Once a reader is enabled to modify users, it must be placed into one of the following five modes:
1) Add One User
2) Add Multiple Users w/ Auto-Increment
3) Activate One User
4) De-Activate One User
5) Delete/Reset One User.
Modifying users on a card reader is similar to modifying user codes at a keypad.
MUST BE A MASTER USER IN ORDER TO MODIFY USER CARD INFORMATION.
ACTION
RESULT
Accesses Code Programming
[master code]
Factory Default is
If the code is valid, the Ready LED will flash.
User Number 2 is used to program user cards, so…
if the control is an NX-6, or NX-8
if the control is an NX-8E
Unit is now ready for you to choose one of the User Card
Programming modes (as if user code 2):
1) Add One User
2) Add Multiple Users (w/ Auto-Increment)
3) Activate Single User
4) De-activate One User
5) Delete / Reset One User
IMPORTANT NOTE
Adding or de-activating user cards from a reader will cause the code for User Number 2 to become invalid. Therefore, it will need to be
re-entered after all user cards are programmed into the readers.
NX-1700E Card Reader
6
ADDING ONE USER
ACTION
RESULT
[STAY]
Accesses Activation mode
[3-digit user number]
Example: if 4-digit user code
or
if 6-digit user codes
If a valid user number is entered, LED1 on any enabled readers
will begin to flash.
Scan the card designated for the user entered
in the previous step.
1) If the user card is not already in the system, it will be added
and mapped to the entered user number and LED1 will
flash.
2) If the card is already in the system, the reader will triple
beep and LED1 will continue flashing.
After about 30 seconds, all the readers in the system will
be updated with the new user card information.
ADDING MULTIPLE USERS WITH AUTO-INCREMENT
ACTION
RESULT
[CANCEL] Use [NIGHT] on NX-1248E
Accesses Activation mode
[3-digit user number]
Example: if 4-digit user code
or
if 6-digit user codes
If a valid user number is entered, LED1 on any enabled readers
will begin to flash.
Scan the card designated for the user entered
in the previous step.
1) If the user card is not already in the system, it will be added
and mapped to the entered user number and LED1 will
continue flashing indicating that the next user card can be
scanned for the next user number.
2) If the card is already in the system, the reader will triple
beep and LED1 will continue flashing; the user number is
not incremented in this case.
Continue scanning user cards until the desired
number of cards has been added.
After about 30 seconds without a card being scanned, all the
readers in the system will be updated with the new user card
information.
By default, user cards are added and activated. In order to add a user card and de-activate it at
the same time, scan and hold the card to be added until two beeps are sounded at the reader.
ACTIVATE ONE USER (SINGLE USER)
ACTION
RESULT
[CHIME] not available on NX-1248E
Accesses Activation mode
[3-digit user number]
Example: if 4-digit user code
or
if 6-digit user codes
If a valid user number is entered, LED1 on any enabled readers
will begin to flash.
Scan any card.
The card information for the user entered in the previous step
will be activated, and LED1 will stop flashing. After about 30
seconds, all the readers in the system will be updated.
Loading...