Intel BOXD5400XS, Desktop Board D5400XS, S5400SF - Server Board Motherboard Product Manual

Intel® Desktop Board D5400XS
Product Guide

Order Number: E24559-001

Revision History

Revision Revision History Date

-001 First release of the Intel® Desktop Board D5400XS Product Guide January 2008

If an FCC declaration of conformity marking is present on the board, the following statement applies:

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

For questions related to the EMC performance of this product, contact:
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124

1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the
user’s authority to operate the equipment.

Tested to comply with FCC standards for home or office use.

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par
le ministére des Communications du Canada.

Disclaimer

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR
GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR
SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR
IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT
OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended
for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and
product descriptions at any time, without notice.

Desktop Board D5400XS may contain design defects or errors known as errata which may cause the product
to deviate from published specifications. Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing
your product order.

Copies of documents which have an ordering number and are referenced in this document, or other Intel
literature, may be obtained from Intel Corporation by going to the World Wide Web site at:
http://www.intel.com/ or by calling 1-800-548-4725.

Intel and the Intel Logo are trademarks of Intel Corporation in the U.S. and other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2008, Intel Corporation. All rights reserved.

OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS

Preface

This Product Guide gives information about board layout, component installation, BIOS
update, and regulatory requirements for Intel

®

Desktop Board D5400XS.

Intended Audience

The Product Guide is intended for technically qualified personnel. It is not intended for
general audiences.

Use Only for Intended Applications

All Intel Desktop Boards are evaluated as Information Technology Equipment (I.T.E.)
for use in personal computers (PC) for installation in homes, offices, schools, computer
rooms, and similar locations. The suitability of this product for other PC or embedded
non-PC applications or other environments, such as medical, industrial, alarm systems,
test equipment, etc. may not be supported without further evaluation by Intel.

Document Organization

The chapters in this Product Guide are arranged as follows:
1 Desktop Board Features: a summary of product features
2 Installing and Replacing Desktop Board Components: instructions on how to install

the Desktop Board and other hardware components
3 Updating the BIOS: instructions on how to update the BIOS
4 Configuring for RAID: information about configuring your system for RAID
A Error Messages and Indicators: information about BIOS error messages, beep

codes, and POST codes
B Regulatory Compliance: describes the board’s adherence to safety standards and

EMC regulations and its product certifications

Conventions

The following conventions are used in this manual:

CAUTION

Cautions warn the user about how to prevent damage to hardware or loss of data.

NOTE

Notes call attention to important information.

iii

Intel Desktop Board D5400XS Product Guide

Terminology

The table below gives descriptions of some common terms used in the product guide.

Term Description

GB Gigabyte (1,073,741,824 bytes)
GHz Gigahertz (one billion hertz)
KB Kilobyte (1024 bytes)
MB Megabyte (1,048,576 bytes)
Mb Megabit (1,048,576 bits)
MHz Megahertz (one million hertz)

iv

Contents

1 Desktop Board Features

Desktop Board Components.................................................................................11

Processors ........................................................................................................13

Main Memory.....................................................................................................13

®

Intel

5400 Chipset............................................................................................14

Audio Subsystem ...............................................................................................14

LAN Subsystem .................................................................................................15

USB 2.0 Support................................................................................................16

Hard Disk and Optical Disk Drive Support ..............................................................16

Enhanced IDE Interface...............................................................................16

Serial ATA .................................................................................................17

Disk Drive Access Indicator..........................................................................18

Legacy I/O........................................................................................................18

Expandability.....................................................................................................19

BIOS................................................................................................................19

Serial ATA and IDE Auto Configuration...........................................................19

PCI and PCI Express* Auto Configuration.......................................................19

Security Passwords.....................................................................................19

Hardware Management .......................................................................................20

Hardware Monitoring and Fan Speed Control ..................................................20

Chassis Intrusion........................................................................................20

Power Management............................................................................................21

Software Support .......................................................................................21

Hardware Support ......................................................................................21

ENERGY STAR* Capable ..............................................................................25

Onboard Power and Reset Buttons........................................................................25

Onboard VR and CPU LEDs ..................................................................................27

Speaker............................................................................................................28

Battery.............................................................................................................28

Real-Time Clock.................................................................................................28

®

Intel

Precision Cooling Technology .......................................................20

ACPI..................................................................................................21

Power Connectors ...............................................................................21

Fan Headers .......................................................................................22

LAN Wake Capabilities..........................................................................22

Instantly Available PC Technology..........................................................23

+5 V Standby Power Indicator...............................................................23

Wake from USB ..................................................................................25

PME# Signal Wake-up Support..............................................................25

WAKE# Signal Wake-up Support ...........................................................25

2 Installing and Replacing Desktop Board Components

Before You Begin ...............................................................................................29

Installation Precautions.......................................................................................30

Prevent Power Supply Overload ....................................................................30

Observe Safety and Regulatory Requirements.................................................30

Installing the I/O Shield ......................................................................................31

v

Intel Desktop Board D5400XS Product Guide

Installing and Removing the Desktop Board ...........................................................32

Installing a Processor .........................................................................................33

Installing a Processor ..................................................................................33

Installing a Processor Fan Heat Sink..............................................................37

Installing an MCH Heat Sink Fan (Optional)............................................................38

Installing and Removing Memory..........................................................................39

Installing DIMMs ........................................................................................39

Removing DIMMs........................................................................................40

Installing a DIMM Cooling Fan (Recommended)...............................................41

Installing and Removing PCI Express x16 Cards .....................................................42

Installing a PCI Express x16 Card .................................................................42

Removing a PCI Express x16 Card ................................................................43

Installing Multiple Graphics Cards .................................................................44

Connecting the IDE Cable....................................................................................44

Connecting the SATA Cables................................................................................46

Connecting to the Internal Headers and Connectors ................................................47

HD Audio Link Header .................................................................................48

S/PDIF Connector.......................................................................................48

Front Panel Audio Header ............................................................................49

IEEE 1394a Header.....................................................................................49

Front Panel Header .....................................................................................49

USB 2.0 Headers ........................................................................................50

Consumer IR (CIR) Headers.........................................................................50

Chassis Intrusion Header.............................................................................51

Connecting to the Flexible Audio System ...............................................................52

Connecting Chassis Fan and Power Supply Cables...................................................53

Connecting Chassis Fan Cables.....................................................................53

Connecting Power Supply Cables ..................................................................54

Setting the BIOS Configuration Jumper .................................................................55

Clearing Passwords ............................................................................................56

Replacing the Battery .........................................................................................57

3 Updating the BIOS

Updating the BIOS with the Intel
Updating the BIOS with the ISO Image BIOS Update File or the Iflash Memory

Update Utility...............................................................................................64

Obtaining the BIOS Update File ....................................................................64

Updating the BIOS with the ISO Image BIOS Update File .................................64

Updating the BIOS with the Iflash Memory Update Utility .................................65

Recovering the BIOS...................................................................................66

®

Express BIOS Update Utility.................................63

4 Configuring for RAID

Configuring for RAID Using Intel

Configuring the BIOS ..................................................................................67

Creating Your RAID Set ...............................................................................67

Loading the Intel Matrix Storage Technology RAID Drivers and Software ............68

Setting Up a “RAID Ready” System ...............................................................68

Configuring for External RAID Using Marvell Storage Technology ..............................68

Configuring the BIOS ..................................................................................68

Creating Your RAID Set ...............................................................................69

Loading the Marvell Storage Technology RAID Drivers and Software ..................69

®

Matrix Storage Technology ...................................67

vi

Contents

A Error Messages and Indicators

BIOS Beep Codes...............................................................................................71

BIOS Error Messages..........................................................................................71

Port 80h POST Codes..........................................................................................72

B Regulatory Compliance

Safety Standards ...............................................................................................77

Place Battery Marking .................................................................................77

European Union Declaration of Conformity Statement..............................................78

Product Ecology Statements ................................................................................79

Recycling Considerations .............................................................................79

Lead-free 2LI/Pb-free 2LI Board ...................................................................82

Restriction of Hazardous Substances (RoHS) ..................................................83

EU RoHS ............................................................................................83

China RoHS ........................................................................................84

EMC Regulations ................................................................................................86

Ensure Electromagnetic Compatibility (EMC) Compliance..................................87

Product Certifications..........................................................................................88

Board-Level Certification Markings ................................................................88

Chassis and Component Certifications............................................................89

Figures

1. Desktop Board D5400XS Components .............................................................11

2. LAN Status LEDs ..........................................................................................15

3. Disk Drive Access Indicator............................................................................18

4. Location of the Standby Power Indicator ..........................................................24

5. Onboard Power and Reset Buttons ..................................................................26

6. Location of the VR and CPU LEDs....................................................................27

7. Installing the I/O Shield ................................................................................31

8. Desktop Board D5400XS Mounting Screw Hole Locations....................................32

9. Lift the Socket Lever.....................................................................................33

10. Lift the Load Plate.........................................................................................34

11. Remove the Protective Socket Cover ...............................................................34

12. Remove the Processor from the Protective Processor Cover ................................35

13. Install the Processor .....................................................................................35

14. Close the Load Plate .....................................................................................36

15. Processor Fan Heat Sink Headers....................................................................37

16. Installing a Typical MCH Heat Sink Fan ............................................................38

17. Installing a DIMM .........................................................................................39

18. DIMM Cooling Fan Header..............................................................................41

19. Installing a PCI Express x16 Card ...................................................................42

20. Removing a PCI Express x16 Card ..................................................................43

21. Connecting the IDE Cable ..............................................................................45

22. Connecting Serial ATA Cables.........................................................................46

23. Internal Headers and Connectors....................................................................47

24. Back Panel Audio Connectors .........................................................................52

25. Location of the Chassis Fan Headers................................................................53

26. Connecting Power Supply Cables ....................................................................54

27. Location of the BIOS Configuration Jumper Block ..............................................55

vii

Intel Desktop Board D5400XS Product Guide

28. Removing the Battery ...................................................................................62

29. POST Code Indicators....................................................................................72

30. Desktop Board D5400XS China RoHS Material Self Declaration Table ...................85

Tables

1. Feature Summary.......................................................................................... 9

2. Desktop Board D5400XS Components .............................................................12

3. LAN Status LEDs ..........................................................................................16

4. HD Audio Link Header Signal Names ...............................................................48

5. Chassis Intrusion Header Signal Names ...........................................................48

6. Front Panel Audio Header Signal Names...........................................................49

7. IEEE 1394a Header Signal Names ...................................................................49

8. Front Panel Header Signal Names ...................................................................49

9. USB 2.0 Header Signal Names........................................................................50

10. Front Panel CIR Receiver (Input) Header Signal Names......................................51

11. Back Panel CIR Header Emitter (Output) Header Signal Names ...........................51

12. Chassis Intrusion Header Signal Names ...........................................................51

13. Jumper Settings for the BIOS Setup Program Modes..........................................56

14. Beep Codes .................................................................................................71

15. BIOS Error Messages ....................................................................................71

16. Port 80h POST Codes ....................................................................................73

16. Port 80h POST Codes (continued) ...................................................................74

17. Safety Standards..........................................................................................77

18. Lead-Free Second Level Interconnect Marks .....................................................83

19. China RoHS Environmentally Friendly Use Period Mark.......................................84

20. EMC Regulations...........................................................................................86

21. Product Certification Markings ........................................................................88

viii

1 Desktop Board Features

This chapter briefly describes the features of Intel® Desktop Board D5400XS. Table 1
summarizes the major features of the Desktop Board.

Table 1. Feature Summary

Form Factor

Processor Support for up to two identical Intel® processors in the LGA771

Main Memory

Chipset Intel® 5400 Chipset consisting of:

Graphics
Audio

Expansion
Capabilities

Legacy I/O Support Legacy I/O Controller that provides Consumer Infrared (CIR) support

Peripheral
Interfaces

SSI/EATX (330.20 millimeters [13.00 inches] x 304.80 millimeters
[12.00 inches])

package

• Four 240-pin, DDR2 SDRAM Fully-Buffered Dual Inline Memory

Module (FBDIMM) sockets

• Support for 800/667 MHz SDRAM

• Support for up to 16 GB of system memory

®

• Intel

• Intel

• Support for multiple PCI Express* graphics cards

• Independent multi-streaming 8-channel (7.1) audio and 2-channel

• HD Audio Link header

• HD Audio front panel header

• Onboard 3-pin S/PDIF connector

• ADAT* optical interface support from a back panel S/PDIF optical

• Four PCI Express x16 connectors

• Two PCI* bus connectors

• Up to 10 USB 2.0 ports:

• Up to two IEEE 1394a ports:

• Six Serial ATA (SATA) ports (3.0 Gb/s) via the Intel 6321ESB I/O

• Two external SATA (eSATA) ports via a discrete controller

• One IDE interface with ATA-66/100 support (two devices)

5400 Memory Controller Hub (MCH)

®

6321ESB I/O Controller Hub

audio subsystem, featuring:

― Intel
― IDT* STAC9274 audio codec

port

― Six ports routed to the back panel
― Four ports routed to two onboard USB headers

― One port routed to a back panel connector
― One port routed to an IEEE 1394a header

Controller Hub

®

High Definition Audio interface

continued

9

Intel Desktop Board D5400XS Product Guide

Table 1. Feature Summary (continued)

RAID

• Intel

• Marvell* Storage Technology for the two eSATA ports

LAN Support Intel® 82573L Gigabit (10/100/1000 Mb/s) Ethernet LAN controller

including an RJ-45 back panel connector with integrated status LEDs

BIOS

• Intel

• 16 Mb Firmware Hub

• Support for SMBIOS

• Intel

• Intel

Power Management

• Support for Advanced Configuration and Power Interface (ACPI)

• Suspend to RAM (STR)

• Wake on USB, PCI, PCI Express, LAN, CIR, and front panel

• ENERGY STAR* capable

Hardware
Management

Hardware monitor with:

• Four fan sensing inputs used to monitor fan activity

• Intel® Precision Cooling Technology fan speed control

• Voltage sensing to detect out of range values

Supported
Operating Systems

• Microsoft Windows Vista* Ultimate

• Microsoft Windows Vista Enterprise

• Microsoft Windows Vista Business

• Microsoft Windows Vista Home Premium

• Microsoft Windows Vista Home Basic

• Microsoft Windows Vista Ultimate 64-bit edition

• Microsoft Windows Vista Enterprise 64-bit edition

• Microsoft Windows Vista Business 64-bit edition

• Microsoft Windows Vista Home Premium 64-bit edition

• Microsoft Windows Vista Home Basic 64-bit edition

• Microsoft Windows* XP Media Center Edition 2005

• Microsoft Windows XP Professional

• Microsoft Windows XP Professional x64 Edition

• Microsoft Windows XP Home

®

Matrix Storage Technology for the six onboard SATA ports

®

Platform Innovation Framework for extensible firmware

interface

®

Rapid BIOS Boot

®

Express BIOS Update

For more information about this Desktop Board, including the Technical Product
Specification, BIOS updates, and device drivers, go to the Desktop Board D5400XS
page at http://www.intel.com/products/motherboard/

10

Desktop Board Features

Desktop Board Components

Figure 1 shows the approximate location of the major components on Desktop Board
D5400XS.

Figure 1. Desktop Board D5400XS Components

11

Intel Desktop Board D5400XS Product Guide

Table 2. Desktop Board D5400XS Components

Label Description

A Auxiliary chassis fan header (4-pin)
B PCI Express x16 connector 3
C PCI Express x16 connector 2
D PCI bus connector 2
E Front panel audio header
F PCI Express x16 connector 1
G PCI bus connector 1
H PCI Express x16 connector 0
I DIMM cooling fan header (3-pin)
J Back panel connectors
K Rear chassis fan header (3-pin)
L Processor (CPU 0) socket
M MCH fan header (3-pin)
N Processor (CPU 0) fan header (4-pin)
O 12 V processor core voltage connectors (2 x 4 pin) (2)
P Processor (CPU 1) fan header
Q Processor (CPU 1) socket
R FBDIMM sockets (4)
S Main power connector (2 x 12 pin)
T Battery
U Front chassis fan header (3-pin)
V IDE connector
W Front panel header
X Serial ATA connectors (6)
Y Port 80h POST code indicator
Z USB 2.0 headers (2)
AA Chassis intrusion header
BB Front panel CIR receiver (input) header
CC Back panel CIR transmitter (output) header
DD BIOS configuration jumper block
EE IEEE 1394a header
FF Onboard reset button
GG Onboard power button
HH Speaker
II High Definition Audio Link header
JJ Auxiliary PCI Express graphics power connector (1 x 4 pin)
KK S/PDIF connector

12

Desktop Board Features

Processors

CAUTION

Failure to use an appropriate power supply and/or not connecting the 12 V (2 x 4 pin)
power connectors to the Desktop Board may result in damage to the board, or the
system may not function properly.

Desktop Board D5400XS supports two Intel processors in the LGA771 package.
Processors are not included with the Desktop Board and must be purchased
separately.

Related Links

Go to the following page or link for more information about:

• Instructions on installing or upgrading the processor, page 33 in Chapter 2

• Supported

http://www.intel.com/products/motherboard/

processors for Desktop Board D5400XS,

Main Memory

NOTE

To be fully compliant with all applicable Intel ® SDRAM memory specifications, the
board should be populated with FBDIMMs that support the Serial Presence Detect
(SPD) data structure. If your memory modules do not support SPD, you will see a
notification to this effect on the screen at power up. The BIOS will attempt to
configure the memory controller for normal operation.

The Desktop Board features the following:

• Four 240-pin DDR2 SDRAM FBDIMM sockets with gold-plated contacts

• 800/667 MHz DDR2 SDRAM interface

• DIMM cooling fan header

The Desktop Board supports the following memory:

• 800/667 MHz Fully Buffered DDR2 DIMMs only

• Up to 4 GB utilizing 512 Mb or 1 Gb technology

• Up to 16 GB utilizing 1 Gb technology

• Serial Presence Detect (SPD) memory only

NOTE

A DIMM cooling fan is recommended for use on Desktop Board D5400XS. Refer to
“Installing a DIMM Cooling Fan” on page 41 in Chapter 2 for more information.

13

Intel Desktop Board D5400XS Product Guide

Related Links

Go to the following links or pages for more information about:

• FBDIMMs, http://www.intel.com/technology/memory/

• Installing memory, page 39 in Chapter 2

• Recommended memory for

http://www.intel.com/products/motherboard/

Desktop Board D5400XS,

Intel® 5400 Chipset

The Intel 5400 Chipset consists of the following devices:

• Intel 5400 Memory Controller Hub (MCH)

• Intel 6321ESB I/O Controller Hub

The MCH provides interfaces to the processors, memory, and the PCI Express bus and
the Intel 6321ESB I/O Controller Hub is a centralized controller for the board’s I/O
paths.

For more information about the Intel 5400 Chipset, see:

http://developer.intel.com/products/server/chipsets/index.htm?iid=chips_body+serv

Audio Subsystem

The onboard audio subsystem consists of the following components:

• Intel 6321ESB I/O Controller Hub

• IDT STAC9274D audio codec

The subsystem has the following headers and connectors:

• Back panel audio connectors, including an S/PDIF optical port

• High Definition (HD) Audio front panel header that provides mic in and line out

signals for front panel audio connectors

• HD Audio Link header used for HDMI video cards

• S/PDIF connector that can be used for HDMI video cards that do not work with the

HD Audio Link header

The audio subsystem supports the following features:

• Dolby* Home Theater

• A signal-to-noise (S/N) ratio of 95 dB

• Independent multi-streaming 8-channel (7.1) audio (using the back panel audio

connectors) and 2-channel audio (using the Intel High Definition Audio front panel

header)

• ADAT optical interface support via the back panel S/PDIF optical port

14

Desktop Board Features

Related Links

Go to the following link or pages for more information about:

• Audio drivers and utilities, http://www.intel.com/products

• The location of the onboard audio headers, Figure 23 on page 47

• The si

• The bac

gnal names for the Intel High Definition Audio front panel header and the HD

Audio Link header, page 48

k panel audio connectors, Figure 24 on page 52

/motherboard/

LAN Subsystem

The LAN subsystem includes:

• Intel 6321ESB I/O Controller Hub

• Intel 82573L Gigabit (10/100/1000 Mb/s) Ethernet LAN controller

• RJ-45 LAN connector with integrated status LEDs

The subsystem features:

• CSMA/CD protocol engine

• LAN connect interface between the Intel 6321ESB I/O Controller Hub and the LAN

controller

• PCI bus power management

Related Links

Go to the following link for information about LAN software and drivers:

http://www.intel.com/products/motherboard/

Two LEDs are built into the RJ-45 LAN connector located on the back panel (see
Figure 2). These LEDs indicate th

e status of the LAN.

Figure 2. LAN Status LEDs

15

Intel Desktop Board D5400XS Product Guide

Table 3 describes the LED states when the board is powered up and the LAN
subsystem is operating.

Table 3. LAN Status LEDs

LED LED Color LED State Indicates

A Off LAN link is not established

Blinking LAN activity is occurring
B

Green

On LAN link is established

N/A Off 10 Mb/s data rate
Green On 100 Mb/s data rate
Yellow On 1000 Mb/s data rate

USB 2.0 Support

The Desktop Board supports up to 10 USB 2.0 ports (six ports routed to back panel
connectors and four ports routed to two onboard headers). USB 2.0 ports are
backward compatible with USB 1.1 devices. USB 1.1 devices will function at USB 1.1
speeds.

In addition to USB 2.0 devices, USB 2.0 operation requires an operating system and
drivers that fully support USB 2.0 transfer rates. Disabling Hi-Speed USB in the BIOS
reverts all USB 2.0 ports to USB 1.1 operation. This may be required to accommodate
operating systems that do not support USB 2.0.

Hard Disk and Optical Disk Drive Support

This section describes the Desktop Board’s support for hard disk and optical disk
drives. The board supports IDE and Serial ATA (SATA) drives.

Enhanced IDE Interface

The board’s IDE interface handles the exchange of information between the processor and
peripheral devices such as hard disk drives and CD-ROM drives. The interface supports:

• Up to two IDE devices (such as hard drives)

• ATAPI-style devices (such as CD-ROM drives)

• Older PIO Mode devices

• Ultra DMA-33 and ATA-66/100 protocols

16

Desktop Board Features

Serial ATA

Desktop Board D5400XS supports six onboard Serial ATA (SATA) channels (3.0 Gb/s)
via the Intel 6321ESB I/O Controller Hub and two External SATA (eSATA) channels
(3.0 Gb/s) via a discrete onboard controller.

The six onboard SATA channels provide support the following RAID (Redundant Array
of Independent Drives) levels using Intel

®

Matrix Storage Technology:

• RAID 0 - data striping

• RAID 1 - data mirroring

• RAID 0+1 (or RAID 10) - data striping and data mirroring

• RAID 5 - distributed parity

The two eSATA channels provide support the following RAID levels using Marvell
Storage Technology:

• RAID 0 - data striping

• RAID 1 - data mirroring

For information on configuring your system for RAID, see Chapter 4.

17

Intel Desktop Board D5400XS Product Guide

Disk Drive Access Indicator

Desktop Board D5400XS includes a blue LED that lights when either a SATA or an IDE
disk drive connected to the board is accessed. Figure 3 shows the location of the
indicator.

Legacy I/O

Desktop Board D5400XS includes an I/O controller that provides the following legacy
I/O features:

• Consumer Infrared (CIR) support

• Low pin count (LPC) interface

• Intelligent power management, including a programmable wake up event interface

• PCI power management support

18

Figure 3. Disk Drive Access Indicator

Desktop Board Features

Expandability

Desktop Board D5400XS provides the following expansion capability:

• Four PCI Express x16 connectors

• Two PCI bus connectors

BIOS

The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, and the
PCI/PCI Express and IDE auto-configuration utilities. The BIOS is stored in the Serial
Peripheral Interface (SPI) Flash device.

The BIOS can be updated by following the instructions on page 63 in Chapter 3.

Serial ATA and IDE Auto Configuration

If you install a Serial ATA or IDE device (such as a hard drive) in your computer, the
auto-configuration utility in the BIOS automatically detects and configures the device
for your computer. You do not need to run the BIOS Setup program after installing a
Serial ATA or IDE device. You can override the auto-configuration options by
specifying manual configuration in the BIOS Setup program.

PCI and PCI Express* Auto Configuration

If you install a PCI/PCI Express add-in card in your computer, the PCI/PCI Express
auto-configuration utility in the BIOS automatically detects and configures the
resources (IRQs, DMA channels, and I/O space) for that add-in card. You do not need
to run the BIOS Setup program after you install a PCI/PCI Express add-in card.

Security Passwords

The BIOS includes security features that restrict whether the BIOS Setup program can
be accessed and who can boot the computer. A supervisor password and a user
password can be set for the BIOS Setup and for booting the computer, with the
following restrictions:

• The supervisor password gives unrestricted access to view and change all Setup

options. If only the supervisor password is set, pressing <Enter> at the password

prompt of Setup gives the user restricted access to Setup.

• If both the supervisor and user passwords are set, you must enter either the

supervisor password or the user password to access Setup. Setup options are then

available for viewing and changing depending on whether the supervisor or user

password was entered.

• Setting a user password restricts who can boot the computer. The password

prompt is displayed before the computer is booted. If only the supervisor

password is set, the computer boots without asking for a password. If both

passwords are set, you can enter either password to boot the computer.

Related Links

For instructions on resetting the password, go to Clearing Passwords on page 56.

19

Intel Desktop Board D5400XS Product Guide

Hardware Management

The hardware management features of Desktop Board D5400XS enable the board to
be compatible with the Wired for Management (WfM) specification. The board has
several hardware management features including the following:

• Fan speed monitoring and control

• Thermal and voltage monitoring

• Chassis intrusion detection

Hardware Monitoring and Fan Speed Control

The features of the hardware monitoring and fan speed control include:

• Monitoring of power supply voltages to detect levels above and below acceptable

values

• Intel

• Thermal sensors in the processors, MCH, and I/O Controller Hub, plus an onboard

• Thermally monitored closed-loop fan control, for all onboard fans, that can adjust

®

Precision Cooling Technology fan speed control, delivering acoustically-

optimized thermal management

remote sensor

fan speed or switch the fans off as needed

Intel® Precision Cooling Technology

Intel Precision Cooling Technology automatically adjusts processor fan speed based on
the processor temperature and adjusts chassis fan speeds based on the internal
system temperature.

Chassis Intrusion

The board supports a chassis security feature that detects if the chassis cover has
been removed. The security feature uses a mechanical switch on the chassis that can
be connected to the chassis intrusion header on the Desktop Board. See Figure 23 for
the location of the c

hassis intrusion header.

20

Desktop Board Features

Power Management

Power management is implemented at several levels, including software support
through the Advanced Configuration and Power Interface (ACPI) and the following
hardware support:

• Power connectors

• Fan headers

• LAN wake capabilities

• Instantly Available PC technology (Suspend to RAM)

• +5 V standby power indicator LED

• Wake from USB

• Power Management Event (PME#) signal wake-up support

• WAKE# signal wake-up support

Desktop Board D5400XS is also ENERGY STAR capable.

Software Support

ACPI

ACPI gives the operating system direct control over the power management and Plug
and Play functions of a computer. The use of ACPI with the Desktop Board requires an
operating system that provides full ACPI support.

Hardware Support

Power Connectors

ATX12V-compliant power supplies can turn off the computer power through system
control. When an ACPI-enabled computer receives the correct command, the power
supply removes all non-standby voltages.

When resuming from an AC power failure, the computer returns to the power state it
was in before power was interrupted (either on or off). The computer’s response can
be set by using the Last Power State feature in the BIOS Setup program’s Boot menu.

The Desktop Board has four power connectors. See Figure 26 on page 54 for the
location of the power co

nnectors.

21

Intel Desktop Board D5400XS Product Guide

Fan Headers

The function/operation of the fans is as follows:

• The fans are on when the computer is in the ACPI S0 state.

• The fans are off when the computer is in the ACPI S3, S4, or S5 state.

• Each fan header is wired to a tachometer input of the hardware monitoring and

control device.

• All fan headers support closed-loop fan control that can adjust the fan speed or

switch the fan on or off as needed.

• All fan headers have a +12 V DC connection.
The Desktop Board has two 4-pin processor fan headers, one 4-pin and two 3-pin

chassis fan headers, one 3-pin MCH fan header, and one 3-pin DIMM cooling fan
header.

LAN Wake Capabilities

CAUTION

For LAN wake capabilities, the 5 V standby line for the power supply must be capable
of delivering adequate +5 V standby current. Failure to provide adequate standby
current when using this feature can damage the power supply.

LAN wakeup capabilities enable remote wake-up of the computer through a network.
The LAN subsystem monitors network traffic and upon detecting a Magic Packet*
frame, it asserts a wake-up signal that powers up the computer.

22

Desktop Board Features

Instantly Available PC Technology

CAUTIONS

For Instantly Available PC technology, the 5 V standby line for the power supply must
be capable of delivering adequate +5 V standby current. Failure to provide adequate
standby current when using this feature can damage the power supply and/or effect
ACPI S3 sleep state functionality.

Power supplies used with this Desktop Board must be able to provide enough standby
current to support the standard Instantly Available (ACPI S3 sleep state) configuration.
If the standby current necessary to support multiple wake events from the PCI and/or
USB buses exceeds power supply capacity, the Desktop Board may lose register
settings stored in memory.

Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to­RAM) sleep state. While in the S3 sleep state, the computer will appear to be off. If
the computer has a dual-colored power LED on the front panel, the sleep state is
indicated by the LED turning amber. When signaled by a wake-up device or event, the
computer quickly returns to its last known awake state.

The Desktop Board supports the PCI Bus Power Management Interface Specification.
Add-in cards that support this specification can participate in power management and
can be used to wake the computer.

+5 V Standby Power Indicator

CAUTION

If the AC power has been switched off and the standby power indicator is still lit,
disconnect the power cord before installing or removing any devices connected to the
board. Failure to do so could damage the board and any attached devices.

The Desktop Board’s standby power indicator, shown in Figure 4, is lit when there is
standby power still present on the board even when the computer appears to be off.
For example, when this green LED is lit, standby power is still present at the memory
module sockets and the PCI bus and PCI Express bus connectors.

23

Intel Desktop Board D5400XS Product Guide

Figure 4. Location of the Standby Power Indicator

Related Links

For more information on standby current requirements for the Desktop Board, refer to
the Technical Product Specification on the Desktop Board D5400XS page at

http://www.intel.com/products/motherboard/

24

.

Desktop Board Features

Wake from USB

NOTE

Wake from USB requires the use of a USB peripheral that supports Wake from USB
and an operating system that supports Wake from USB.

USB bus activity wakes the computer from an ACPI S3 state.

PME# Signal Wake-up Support

When the PME# signal on the PCI bus is asserted, the computer wakes from an
ACPI S1, S3, S4, or S5 state.

WAKE# Signal Wake-up Support

When the WAKE# signal on the PCI Express bus is asserted, the computer wakes from
an ACPI S1, S3, S4, or S5 state.

ENERGY STAR* Capable

In 2007, the US Department of Energy and the US Environmental Protection Agency
revised the ENERGY STAR requirements. Intel worked directly with these two
governmental agencies to define the new requirements. Currently Intel Desktop
Boards are capable of meeting the new ENERGY STAR requirements depending upon
system configuration.

Go to the following link for information and recommendations concerning the new
ENERGY STAR requirements: http://www3.intel.com/cd/channel/reseller/asmo-

na/eng/337748.htm.

Onboard Power and Reset Buttons

CAUTION

Electrostatic discharge (ESD) can damage components. Perform the procedure
described in this section only at an ESD workstation using an antistatic wrist strap and
a conductive foam pad. If such a station is not available, you can provide some ESD
protection by wearing an antistatic wrist strap and attaching it to a metal part of the
computer chassis.

A power button (Figure 5, A) and a reset button (Figure 5, B) on the Desktop Board
can be
facilities to remove standby power before making changes to the system configuration,
or for testing purposes. The reset button can be used to reset the system during
testing.

used to control the board. The power button is intended for use at integration

25

Intel Desktop Board D5400XS Product Guide

The power and reset buttons on the front panel are recommended for all other
instances of power cycling or resetting the computer.

Figure 5. Onboard Power and Reset Buttons

26

Desktop Board Features

Onboard VR and CPU LEDs

The Desktop board contains a red VR LED and a red CPU LED for each processor as
shown in Figure 6). These LEDs indicate the following conditions:

• When lit, the VR LE

processor voltage regulator circuit that could a

• When lit, the CPU LEDs (Figure 6, B and C) indicate an elevated tem

the processor that could affect performance.

Ds (Figure 6, A and D) indicate an elevated temperature in the

ffect performance.

perature on

Figure 6. Location of the VR and CPU LEDs

27

Intel Desktop Board D5400XS Product Guide

Speaker

A speaker mounted on the Desktop Board provides audible error code (beep code)
information during the Power-On Self-Test (POST). Refer to Appendix A for a
description of the board’s beep codes.

Battery

A battery on the Desktop Board keeps the values in CMOS RAM and the clock current
when the computer is turned off. Go to page 57 for instructions on how to replace the
battery.

Real-Time Clock

The Desktop Board has a time-of-day clock and 100-year calendar. The battery on the
Desktop Board keeps the clock current when the computer is turned off.

28

2 Installing and Replacing Desktop

Board Components

This chapter tells you how to:

• Install the I/O shield

• Install and remove the Desktop Board

• Install a processor

• Install an MCH heat sink fan

• Install and remove memory

• Install and remove a PCI Express x16 card

• Connect the IDE and Serial ATA cables

• Connect to the internal headers and connectors

• Connect to the audio system

• Connect chassis fan and power supply cables

• Set the BIOS configuration jumper

• Clear passwords

• Replace the battery

Before You Begin

CAUTIONS

The procedures in this chapter assume familiarity with the general terminology
associated with personal computers and with the safety practices and regulatory
compliance required for using and modifying electronic equipment.

Disconnect the computer from its power source and from any telecommunications
links, networks, or modems before performing any of the procedures described in this
chapter. Failure to disconnect power, telecommunications links, networks, or modems
before you open the computer or perform any procedures can result in personal injury
or equipment damage. Some circuitry on the board can continue to operate even
though the front panel power button is off.

Follow these guidelines before you begin:

• Always follow the steps in each procedure in the correct order.

• Set up a log to record information about your computer, such as model, serial

numbers, installed options, and configuration information.

• Electrostatic discharge (ESD) can damage components. Perform the procedures

described in this chapter only at an ESD workstation using an antistatic wrist strap

and a conductive foam pad. If such a station is not available, you can provide

some ESD protection by wearing an antistatic wrist strap and attaching it to a

metal part of the computer chassis.

29

Intel Desktop Board D5400XS Product Guide

Installation Precautions

When you install or test the Intel Desktop Board, observe all warnings and cautions in
the installation instructions.

To avoid personal injury, be careful of:

• Sharp pins on connectors

• Sharp pins on printed circuit assemblies

• Rough edges and sharp corners on the chassis

• Hot components (such as processors, voltage regulators, and heat sinks)

• Damage to wires that could cause a short circuit

Make sure that the green standby power indicator (see Figure 4) is not lit before
i

nstalling or removing any devices connected to the board.

Observe all warnings and cautions that instruct you to refer computer servicing to
qualified technical personnel.

Prevent Power Supply Overload

Do not overload the power supply output. To avoid overloading the power supply,
make sure that the calculated total current loads of all the modules within the
computer is less than the output current rating of each of the power supplies output
circuits.

Observe Safety and Regulatory Requirements

Read and follow the instructions in this section and the instructions supplied with the
chassis and associated modules. If you do not follow these instructions and the
instructions provided by the chassis and module suppliers, you increase your safety
risk and the possibility of noncompliance with regional laws and regulations. If the
instructions for the chassis are inconsistent with these instructions or the instructions
for associated modules, contact the supplier to find out how you can ensure that your
computer meets safety and regulatory requirements.

Related Links

For information about the Desktop Board’s regulatory compliance, go to Appendix B on
page 77.

30

Installing and Replacing Desktop Board Components

Installing the I/O Shield

The Desktop Board comes with an I/O shield. When installed in the chassis, the shield
blocks radio frequency transmissions, protects internal components from dust and
foreign objects, and promotes correct airflow within the chassis.

NOTE

Desktop Board D5400XS requires a chassis that meets the SSI/EATX Chassis
specification (see http://ssiforum.oaktree.com/pd
list of recommended chassis and power supplies for this Desktop Board, refer to the
Intel Desktop Board D5400XS page at

http://support.intel.com/support/motherboards/desktop/

Install the I/O shield before installing the Desktop Board in the chassis. Place the
shield inside the chassis as shown in Figure 7. Press the shield into place so that it fits
t

ightly and securely. If the shield does not fit, obtain a properly sized shield from the

chassis supplier.

fs/SSI%20EEB%20v3-61.pdf). For a

.

Figure 7. Installing the I/O Shield

31

Intel Desktop Board D5400XS Product Guide

Installing and Removing the Desktop Board

CAUTION

Only qualified technical personnel should perform this procedure. Disconnect the
computer from its power source before performing the procedures described here.
Failure to disconnect the power before you open the computer can result in personal
injury or equipment damage.

Refer to your chassis manual for instructions on installing and removing the Desktop
Board.

CAUTION

To ensure that you do not inadvertently short out the board during installation, use the
enclosed Board Mounting Template to determine the appropriate location of chassis
mounting standoffs.

Be sure to remove the Board Mounting Template from the chassis before installing the
board. Failure to do so can result in equipment damage.

Figure 8 shows the location of t

he mounting screw holes for Desktop Board D5400XS.

Figure 8. Desktop Board D5400XS Mounting Screw Hole Locations

32

Installing and Replacing Desktop Board Components

Installing a Processor

Instructions on how to install processors on the Desktop Board are given in the
following section.

Installing a Processor

CAUTION

Before installing or removing a processor, make sure AC power has been removed by
unplugging the power cord from the computer. The standby power indicator should
not be lit (see Figure 4 on page 24). Failure to follow these precautions could result in
damage

To install a processor, follow these instructions:

1. Observe the precautions in "Before You Begin" on page 29.

2. Open the so

to the processor and the board.

cket lever by pushing the lever down and away from the socket

(Figure 9, A and B).

Figure 9. Lift the Socket Lever

33

Intel Desktop Board D5400XS Product Guide

3. Lift the load plate (Figure 10, A). Do not touch the socket contacts (Figure 10, B).

Figure 10. Lift the Load Plate

4. Remove the plastic protective socket cover from the load plate (Figure 11). Do not

discard the protective socket cover. Always replace the socket cover if the

processor is removed from the socket.

Figure 11. Remove the Protective Socket Cover

34

Installing and Replacing Desktop Board Components

5. Remove the processor from the protective processor cover. Hold the processor

only at the edges, being careful not to touch the bottom of the processor (see

Figure 12). Do not discard the

protective processor cover. Always replace the

processor cover if the processor is removed from the socket.

Figure 12. Remove the Processor from the Protective Processor Cover

6. Hold the processor with your thumb and index fingers oriented as shown in

Figure 13. Make sure your fingers align to the socket cutouts (Figure 13, A). Align

the notch

st

raight down without tilting or sliding it in the socket.

(Figure 13, B) with the socket (Figure 13, C). Lower the processor

Figure 13. Install the Processor

35

Intel Desktop Board D5400XS Product Guide

7. Pressing down on the load plate (Figure 14, A), close and engage the socket lever

(Figure 14, B).

Figure 14. Close the Load Plate

36

Installing and Replacing Desktop Board Components

Installing a Processor Fan Heat Sink

Desktop Board D5400XS has mounting holes for fan heat sinks for each processor.
The mounting holes are designed to accommodate standard LGA775 heat sinks even
though this board has LGA771 processor sockets.

NOTE

For a list of recommended heat sinks for Desktop Board D5400XS, refer to the Desktop
Board D5400XS page at http://www.intel.com/products/motherboard/

After you install the fan heat sinks, connect the fan power connectors to the 4-pin
processor fan headers (see Figure 15). A fan with a 4-pin connector as shown in
Figure 15, A is recommended; however, a
can be used. Since the fan with a 3-pin connector cannot use the onboard fan control,
the fan will always operate at full speed.

fan with a 3-pin connector (Figure 15, B)

.

Figure 15. Processor Fan Heat Sink Headers

37

Intel Desktop Board D5400XS Product Guide

Installing an MCH Heat Sink Fan (Optional)

If your system application requires more MCH cooling than is provided by the MCH
passive heat sink, you can add a cooling fan to the MCH passive heat sink by using the
included MCH heat sink fan mounting bracket. This fan mounting bracket is designed
to accommodate a 40 mm x 10 mm or 40 mm x 20 mm, 12 V dc fan. Use the board’s
3-pin MCH fan header to supply power to the MCH fan.

NOTE

An MCH heat sink fan is not included with Desktop Board D5400XS and must be
purchased separately.

To install an MCH heat sink fan, follow these instructions:

1. Observe the precautions in "Before You Begin" on page 29.

2. Attach

fasteners (Figure 16, A) supplied with the fan. Slide the four legs of the bracket

over

place.

3. Attach

the fan (Figure 16, A) to the fan mounting bracket (Figure 16, B) using the

the heat sink fins (Figure 16, C) and push down until the bracket “clicks” into

the fan power connector to the MCH fan header (Figure 16, D).

Figure 16. Installing a Typical MCH Heat Sink Fan

38

Installing and Replacing Desktop Board Components

Installing and Removing Memory

Desktop board D5400XS has four 240-pin FBDIMM sockets providing quad-channel
memory support with one DIMM per channel. The sockets are keyed so that they will
accept only FBDIMMs.

Installing DIMMs

To install a DIMM, follow these steps:

1. Observe the precautions in "Before You Begin" on page 29.

2. Turn off all peripheral devices connected to the

and disconnect the AC power cord.

3. Remove the computer’s cover and locate the DIMM sockets (see Figure 17).

computer. Turn off the computer

4. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the

open position.

5. Holding the DIMM by the edges, remove it from its anti-static package.

Figure 17. Installing a DIMM

39

Intel Desktop Board D5400XS Product Guide

6. Position the DIMM above the socket. Align the small notch at the bottom edge of

the DIMM with the key in the socket (see inset in Figure 17).

7. In

sert the bottom edge of the DIMM into the socket.

8. When the DIMM is inserted, push down on the top edge of the DIMM until the

retaining clips snap into place. Make sure the clips are firmly in place.

9. Replace the computer’s cover and reconnect the AC power cord.

Removing DIMMs

To remove a DIMM, follow these steps:

1. Observe the precautions in "Before You Begin" on page 29.

2. Turn off all peripheral devices connected to the

3. Remove the AC power cord from the computer.

4. Remove the computer’s cover.

5. Gently spread the retaining clips at each end of the DIMM socket. The DIMM pops

out of the socket.

6. Hold the DIMM by the edges, lift it away from the socket, and store it in an

anti-static package.

7. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM

sockets.

8. Replace the computer’s cover and reconnect the AC power cord.

computer. Turn off the computer.

40

Installing and Replacing Desktop Board Components

Installing a DIMM Cooling Fan (Recommended)

It is recommended that a DIMM cooling fan be installed on Desktop Board D5400XS to
ensure proper memory operation.

Use the board’s 3-pin DIMM fan header (Figure 18) to supply power to

NOTE

A DIMM cooling fan is not included with Desktop Board D5400XS and must be
purchased separately. A list of compatible clip-on fans is available on the Desktop
Board D5400XS page at http://www.intel.com/products/motherboard/

the fan.

.

Figure 18. DIMM Cooling Fan Header

41

Intel Desktop Board D5400XS Product Guide

Installing and Removing PCI Express x16
Cards

CAUTION

When installing a PCI Express card on the Desktop Board, ensure that the card is fully
seated in the PCI Express connector before you power on the system. If the card is
not fully seated in the connector, an electrical short may result across the connector
pins. Depending on the over-current protection of the power supply, certain Desktop
Board components and/or traces may be damaged.

Installing a PCI Express x16 Card

Follow these instructions to install a PCI Express x16 card:

1. Observe the precautions in "Before You Begin" on page 29.

2. Place the ca

t

he card until it is completely seated in the connector and the card retention notch

on the card snaps into place around the retention mechanism pin on the connector.

3. Secure the card’s metal bracket to the chassis back panel with a screw

(Figure 19, B).

rd in a PCI Express x16 connector (Figure 19, A) and press down on

Figure 19. Installing a PCI Express x16 Card

42

Installing and Replacing Desktop Board Components

Removing a PCI Express x16 Card

Follow these instructions to remove a PCI Express x16 card from a connector:

1. Observe the precautions in "Before You Begin" on page 29.

2. Remove the

chassis bac

3. Push the card ejector lever down using the tip of a pencil or similar tool

(Figure 20, B) in the notch. This will release the card from the connector (C).

4. P

ull the card straight up.

screw (Figure 20, A) that secures the card’s metal bracket to the

k panel.

Figure 20. Removing a PCI Express x16 Card

43

Intel Desktop Board D5400XS Product Guide

Installing Multiple Graphics Cards

The Desktop Board supports technology that allows you to install linked PCI Express
x16 graphics cards.

When installing multiple graphics cards in the PCI Express x16 connectors, refer to the
card manufacturer’s instructions to determine correct card placement and
interconnection. Use the connectors or cables included with the Desktop Board to
connect the two graphics cards together.

For more complete installation and configuration information refer to the
documentation supplied by the graphics card manufacturer or visit their website.

For a list of compatible graphics cards, go to the Desktop Board D5400XS page at

http://www.intel.com/products/motherboard/

.

Connecting the IDE Cable

The included IDE cable can be used to connect two IDE drives to the Desktop Board
using the IDE connector. The cable supports the ATA-66/100 transfer protocol.
Figure 21 shows the correct installation of the

cable.

NOTES

ATA-66/100 compatible cables are backward compatible with drives using slower IDE
transfer protocols. If an ATA-66/100 disk drive and a disk drive using any other IDE
transfer protocol are attached to the same cable, the maximum transfer rate between
the drives may be reduced to that of the slowest drive.

Do not connect an ATA device as a slave on the same IDE cable as an ATAPI master
device. For example, do not connect an ATA hard drive as a slave to an ATAPI
CD-ROM drive.

For correct function of the cable:

• Observe the precautions in "Before You Begin" on page 29.

• Attach the cable end with the single connect

(Figure 21, A).

• Attach the cable end with the two cl

the drives (Figure 21, B).

osely spaced connectors (gray and black) to

or (blue) to the Intel Desktop Board

44

Installing and Replacing Desktop Board Components

Figure 21. Connecting the IDE Cable

45

Intel Desktop Board D5400XS Product Guide

Connecting the SATA Cables

The included SATA cables support the SATA protocol. Each cable can be used to
connect one internal SATA drive to the Desktop Board. For correct cable function:

1. Observe the precautions in “Before You Begin” on page 29.

2. Attach

(Figure 22, A) and attach the other end of the

(Figure 22, B).

one end of the SATA cable to one of the SATA connectors on the board

cable to the SATA drive

Figure 22. Connecting Serial ATA Cables

46

Installing and Replacing Desktop Board Components

Connecting to the Internal Headers and
Connectors

Before connecting cables to any of the internal headers, observe the precautions in
“Before You Begin” on page 29. Figure 23 shows the location of the internal headers
and co

nnectors on Intel Desktop Board D5400XS.

Item Description Item Description
A HD Audio Link F USB 2.0 (2)
B S/PDIF G Front panel CIR receiver (input)
C Front panel audio H Back panel CIR emitter (output)
D IEEE 1394a I Chassis intrusion
E Front panel

Figure 23. Internal Headers and Connectors

47

Intel Desktop Board D5400XS Product Guide

HD Audio Link Header

Figure 23, A shows the location of the HD Audio Link header. Table 4 shows the pin
assignments and signal names for the HD Audio Link header.

Table 4. HD Audio Link Header Signal Names

Pin Signal Name Pin Signal Name

1 BCLK 2 Ground
3 RST# 4 3.3 Vcc
5 SYNC 6 Ground
7 SDO 8 3.3 Vcc
9 SDI0 10 +12 V
11 SDI1 12 Key
13 No Connection 14 3.3 V STBY
15 No Connection 16 Ground

S/PDIF Connector

Figure 23, B shows the location of the S/PDIF connector. This connector can be
used with HDMI video cards that do not work with the HD Audio Link header (see
Figure 23, A). Table 5 shows the pin assignments a

nd signal names for the S/PDIF

connector.

Table 5. Chassis Intrusion Header Signal Names

Pin Description

1 Vcc
2 S/PDIF Out
3 Ground

48

Installing and Replacing Desktop Board Components

Front Panel Audio Header

Figure 23, C shows the location of the front panel audio header. Table 6 shows the pin
assignments and signal names for the front panel audio header.

Table 6. Front Panel Audio Header Signal Names

Pin Signal Name Pin Signal Name

1 PORT 1L 2 GND
3 PORT 1R 4 PRESENCE#
5 PORT 2R 6 SENSE1_RETURN
7 SENSE_SEND 8 KEY (no pin)
9 PORT 2L 10 SENSE2_RETURN

IEEE 1394a Header

Figure 23, D shows the location of the IEEE 1394a header. Table 7 shows the pin
assignments and signal names for the IEEE 1394a header.

Table 7. IEEE 1394a Header Signal Names

Pin Signal Name Pin Signal Name

1 TPA1+ 2 TPA1­3 Ground 4 Ground
5 TPA2+ 6 TPA2­7 +12 V 8 +12 V
9 Key (no pin) 10 Ground

Front Panel Header

Figure 23, E shows the location of the front panel header. Table 8 shows the pin
assignments and signal names for the front panel header.

Table 8. Front Panel Header Signal Names

Pin Description In/Out Pin Description In/Out

Hard Drive Activity LED Power LED

1 Hard disk LED pull-up to +5 V Out 2 Front panel green LED Out
3 Hard disk active LED Out 4 Front panel yellow LED Out

Reset Switch On/Off Switch

5 Ground 6 Power switch In
7 Reset switch In 8 Ground

Power Not Connected

9 Power Out 10 No pin

49

Intel Desktop Board D5400XS Product Guide

USB 2.0 Headers

Figure 23, F shows the location of the USB 2.0 headers. Table 9 shows the pin
assignments and signal names for each USB 2.0 header. Each USB header can be
used to connect two USB devices.

Table 9. USB 2.0 Header Signal Names

USB Port A USB Port B

Pin Signal Name Pin Signal Name

1 Power (+5 V) 2 Power (+5 V)
3 D- 4 D­5 D+ 6 D+
7 Ground 8 Ground
9 Key 10 No Connection

Note: USB ports may be assigned as needed.

NOTE

Computer systems that have an unshielded cable attached to a USB port might not
meet FCC Class B requirements, even if no device or a low-speed USB device is
attached to the cable. Use a shielded cable that meets the requirements for a
full-speed USB device.

Consumer IR (CIR) Headers

The Desktop Board has two CIR headers: the input or receiver header (Figure 23, G)
and the output or emitter header (Figure 23, H). The receiver header consists of a
f

iltered translated infrared input compliant with Microsoft CIR specifications and a
“learning” infrared input. The learning input is a high-pass input which the computer
can use to “learn” to speak the infrared communication language of other user
remotes. The emitter header consists of two output ports which the computer can use
to emulate “learned” infrared commands in order to control external electronic
hardware.

NOTE

The Consumer IR option must be enabled in the system BIOS before it can function.
Press <F2> at boot to enter the system BIOS, and go to Advanced > Peripheral
Configuration > Enhanced Consumer IR, and set this option to Enabled.

Table 10 shows the pin assignments and
(input) header and Table 11 shows the pin assignments and signal na
panel CIR emitter (output) header.

signal names for the front panel CIR receiver

mes for the back

50

Installing and Replacing Desktop Board Components

Table 10. Front Panel CIR Receiver (Input) Header Signal Names

Pin Signal Name Pin Signal Name

1 Ground 2 LED

3 No Connection 4 Learn-In

5 +5 V Standby 6 Vcc

7 Key (no pin) 8 CIR Input

Table 11. Back Panel CIR Header Emitter (Output) Header Signal Names

Pin Signal Name Pin Signal Name

1 Emitter Out 1 2 Emitter Out 2

3 Ground 4 Key (no pin)

5 Jack Detect 1 6 Jack Detect 2

Chassis Intrusion Header

Figure 23, I shows the location of the chassis intrusion header. This header can be
connected to a mechanical switch on the chassis to detect if the chassis cover is
removed. Table 12 shows the pin assignments and
intrusion header.

signal names for the chassis

Table 12. Chassis Intrusion Header Signal Names

Pin Description

1 Intruder

2 Ground

51

Intel Desktop Board D5400XS Product Guide

Connecting to the Flexible Audio System

After installing the IDT* audio driver from the Intel® Express Installer DVD-ROM, the
multi-channel audio feature can be enabled. Figure 24 shows the back panel audio
connectors

. The default connector assignments are shown in the table.

Item Description

A Surround Left and Right

B Center Channel and LFE (Subwoofer)

C Side Surround Left and Right/Line

In/Retasking Jack

D Line Out

E Mic In

F S/PDIF Digital Audio Out (Optical)

Figure 24. Back Panel Audio Connectors

NOTE

The back panel line out connector is designed to power either headphones or amplified
speakers only. Poor audio quality may occur if passive (non-amplified) speakers are
connected to this output.

52

Installing and Replacing Desktop Board Components

Connecting Chassis Fan and Power Supply
Cables

Connecting Chassis Fan Cables

Connect chassis fan cables to the 3-pin and 4-pin chassis fan headers on the Desktop
Board. Figure 25 shows the location of the

chassis fan headers.

Figure 25. Location of the Chassis Fan Headers

53

Intel Desktop Board D5400XS Product Guide

Connecting Power Supply Cables

CAUTION

Failure to use an appropriate power supply and/or not connecting the 12 V (2 x 4 pin)
power connectors to the Desktop Board may result in damage to the board or the
system may not function properly.

CAUTION

Use of the 1 x 4 power connector is required with ATX12V power supplies when using
PCI Express add-in cards that can consume 75 W or greater. Failure to do so may
cause damage to the Desktop Board and the add-in cards.

Figure 26 shows the location of the power connectors.

Figure 26. Connecting Power Supply Cables

54

Installing and Replacing Desktop Board Components

1. Observe the precautions in "Before You Begin" on page 29.

2. Connect the 12 V processor core voltage power supply cables to the 2 x 4 pin

connectors. Make sure to connect one supply cable for each installed processor.

3. If necessary, connect the 1 x 4 power supply cable to the 1 x 4 connector.

4. Connect the main power supply cable to the 2 x 12 pin connector.

Setting the BIOS Configuration Jumper

NOTE

Always turn off the power and unplug the power cord from the computer before
moving the jumper. Moving the jumper with the power on may result in unreliable
computer operation.

Figure 27 shows the location of the Desktop Board’s BIOS confi

guration jumper block.

Figure 27. Location of the BIOS Configuration Jumper Block

55

Intel Desktop Board D5400XS Product Guide

The three-pin BIOS jumper block enables all board configurations to be done in the
BIOS Setup program. Table 13 shows the jumper setti

ngs for the BIOS Setup

program modes.

Table 13. Jumper Settings for the BIOS Setup Program Modes

Jumper Setting Mode Description

Normal (default) (1-2) The BIOS uses the current configuration and

passwords for booting.

Configure (2-3) After the Power-On Self-Test (POST) runs, the

BIOS displays the Maintenance Menu. Use this
menu to clear passwords.

Recovery (None) The BIOS recovers data in the event of a failed

BIOS update.

Clearing Passwords

This procedure assumes that the board is installed in the computer and the
configuration jumper block is set to normal mode.

1. Observe the precautions in "Before You Begin" on page 29.

2. Turn off all peripheral devices connected to the

Disconnect the computer’s power cord from the AC power source (wall outlet or
power adapter).

3. Remove the computer cover.

4. Find the configuration jumper block (see Figure 27).

5. Place the jumper on pins 2-3 as shown

below.

6. Replace the cover, plug in the computer, turn on the computer, and allow it to

boot.

7. The computer starts the Setup program. Setup displays the Maintenance menu.

8. Use the arrow keys to select Clear Passwords. Press <Enter> and Setup displays a

pop-up screen requesting that you confirm clearing the password. Select Yes and
press <Enter>. Setup displays the maintenance menu again.

9. Press <F10> to save the current values and exit Setup.

10. Turn off the computer. Disconnect the computer’s power cord from the AC power

source.

computer. Turn off the computer.

56

Installing and Replacing Desktop Board Components

11. Remove the computer cover.

12. To restore normal operation, place the jumper on pins 1-2 as shown below.

13. Replace the cover, plug in the computer, and turn on the computer.

Replacing the Battery

A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When
the computer is not plugged into a wall socket, the battery has an estimated life of
three years. When the computer is plugged in, the standby current from the power
supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at
25 ºC with 3.3 VSB applied.

When the voltage drops below a certain level, the BIOS Setup program settings stored
in CMOS RAM (for example, the date and time) might not be accurate. Replace the
battery with an equivalent one. Figure 28 on page 62 shows the location of the
battery.

CAUTION

Risk of explosion if the battery is replaced with an incorrect type. Batteries should be
recycled where possible. Disposal of used batteries must be in accordance with local
environmental regulations.

PRECAUTION

Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les
piles usagées doivent être recyclées dans la mesure du possible. La mise au rebut des
piles usagées doit respecter les réglementations locales en vigueur en matière de
protection de l'environnement.

FORHOLDSREGEL

Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier
bør om muligt genbruges. Bortskaffelse af brugte batterier bør foregå i
overensstemmelse med gældende miljølovgivning.

OBS!

Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier
bør kastes i henhold til gjeldende miljølovgivning.

VIKTIGT!

Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras
enligt de lokala miljövårdsbestämmelserna.

57

Intel Desktop Board D5400XS Product Guide

VARO

Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on
mahdollista. Käytetyt paristot on hävitettävä paikallisten ympäristömääräysten
mukaisesti.

VORSICHT

Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie
darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen
Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen
des Herstellers entsprechend.

AVVERTIMENTO

Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto.
Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per
disfarsi delle pile usate, seguire le istruzioni del produttore.

PRECAUCIÓN

Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice
solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del
equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del
fabricante.

WAARSCHUWING

Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type
batterij. Batterijen moeten zoveel mogelijk worden gerecycled. Houd u bij het
weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving.

ATENÇÃO

Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto.
As baterias devem ser recicladas nos locais apropriados. A eliminação de baterias
usadas deve ser feita de acordo com as regulamentações ambientais da região.

AŚCIAROŽZNAŚĆ

Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу.
Акумулятары павінны, па магчымасці, перепрацоўвацца. Пазбаўляцца ад старых
акумулятараў патрэбна згодна з мясцовым заканадаўствам па экалогіі.

UPOZORNÌNÍ

V případě výměny baterie za nesprávný druh může dojít k výbuchu. Je-li to možné,
baterie by měly být recyklovány. Baterie je třeba zlikvidovat v souladu s místními
předpisy o životním prostředí.

58

Installing and Replacing Desktop Board Components

Προσοχή

Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η μπαταρία αντικατασταθεί από μία
λανθασμένου τύπου. Οι μπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι
δυνατό. Η απόρριψη των χρησιμοποιημένων μπαταριών πρέπει να γίνεται σύμφωνα με
τους κατά τόπο περιβαλλοντικούς κανονισμούς.

VIGYÁZAT

Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket
lehetőség szerint újra kell hasznosítani. A használt telepeket a helyi környezetvédelmi
előírásoknak megfelelően kell kiselejtezni.

AWAS

Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri
sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi
peraturan alam sekitar tempatan.

OSTRZEŻENIE

Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu
baterii. Zużyte baterie należy w miarę możliwości utylizować zgodnie z odpowiednimi
przepisami ochrony środowiska.

PRECAUŢIE

Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător.
Bateriile trebuie reciclate, dacă este posibil. Depozitarea bateriilor uzate trebuie să
respecte reglementările locale privind protecţia mediului.

ВНИМАНИЕ

При использовании батареи несоответствующего типа существует риск ее взрыва.
Батареи должны быть утилизированы по возможности. Утилизация батарей должна
проводится по правилам, соответствующим местным требованиям.

UPOZORNENIE

Ak batériu vymeníte za nesprávny typ, hrozí nebezpečenstvo jej výbuchu. Batérie by
sa mali podľa možnosti vždy recyklovať. Likvidácia použitých batérií sa musí vykonávať
v súlade s miestnymi predpismi na ochranu životného prostredia.

59

Intel Desktop Board D5400XS Product Guide

POZOR

Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo.
Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi

okoljevarstvenimi predpisi.

.

UYARI

Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri
dönüştürülmelidir. Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır.

OСТОРОГА

Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху.
Якщо можливо, використані батареї слід утилізувати. Утилізація використаних
батарей має бути виконана згідно місцевих норм, що регулюють охорону довкілля.

60

Installing and Replacing Desktop Board Components

61

Intel Desktop Board D5400XS Product Guide

To replace the battery, follow these steps:

1. Observe the precautions in "Before You Begin" (see page 29).

2. Turn off all peripheral devices connected to t

he computer. Disconnect the

computer’s power cord from the AC power source (wall outlet or power adapter).

3. Remove the computer cover.

4. Locate the battery on the board (see Figure 28).

5. P

ush the battery retention clip aside and remove the battery from the connector as

shown in Figure 28. Note the orientation of the “+” and “-” on the battery.

6. In

stall the new battery in the connector, orienting the “+” and “-” correctly.

7. Replace the computer cover.

62

Figure 28. Removing the Battery

3 Updating the BIOS

The BIOS Setup program can be used to view and change the BIOS settings for the
computer. You can access the BIOS Setup program by pressing the <F2> key after
the Power-On Self-Test (POST) memory test begins and before the operating system
boot begins.

This chapter tells you how to update the BIOS by either using the Intel Express BIOS
Update utility or the Iflash Memory Update utility, and how to recover the BIOS if an
update fails.

Updating the BIOS with the Intel® Express
BIOS Update Utility

With the Intel Express BIOS Update utility you can update the system BIOS while in
the Windows environment. The BIOS file is included in an automated update utility
that combines the functionality of the Intel
of use of Windows-based installation wizards.

®

Flash Memory Update Utility and the ease

To update the BIOS with the Intel Express BIOS Update utility:

1. Go to the Intel World Wide Web site:

http://support.intel.com/support/motherboards/desktop/

2. Navigate to the D5400XS page, click “[view] Latest BIOS updates,” and select the

Express BIOS Update utility file.

3. Download the file to your hard drive. (You can also save this file to a removable

USB device. This is useful if you are updating the BIOS for multiple identical
systems.)

4. Close all other applications. This step is required. Your system will be rebooted at

the last Express BIOS Update window.

5. Double-click the executable file from the location on your hard drive where it was

saved. This runs the update program.

6. Follow the instructions provided in the dialog boxes to complete the BIOS update.

63

Intel Desktop Board D5400XS Product Guide

Updating the BIOS with the ISO Image BIOS
Update File or the Iflash Memory Update
Utility

You can use the information in this section to update the BIOS using either the Iflash
Memory Update Utility or the ISO Image BIOS update file.

Obtaining the BIOS Update File

You can update to a new version of the BIOS by using the ISO Image BIOS update file
(recommended), or Iflash BIOS update file.

The ISO Image BIOS update file is a standardized image of a bootable CD-ROM that
can be used to create a bootable CD that will update the BIOS.

The Iflash BIOS update file is a compressed file that contains the files you need to
update the BIOS. The Iflash BIOS update file contains:

• New BIOS file (including the Intel

• Intel

• Intel Flash Memory Update Utility

®

Integrator Toolkit Configuration File (optional)

®

Management Engine Firmware Image)

You can obtain either of these files through your computer supplier or by navigating to
the Desktop Board D5400XS page on the Intel World Wide Web site at

http://support.intel.com/support/motherboards/desktop

Navigate to the D5400XS page, click “[view] Latest BIOS updates,” and select the ISO
Image BIOS Update or Iflash BIOS Update utility file.

.

Updating the BIOS with the ISO Image BIOS Update
File

The ISO Image BIOS update allows for the update of an Intel® Desktop Board BIOS to
the latest production release regardless of the operating system installed on the
computer's hard drive and without the need to remove the BIOS configuration jumper.
It requires a blank CD-R, a read/writeable CD drive, and software capable of
uncompressing and writing the ISO image file to CD.

The image uses ISOLINUX* bootloader and automatically launches a script to upgrade
the BIOS via the Iflash utility.

64

Updating the BIOS

CAUTION

Do not interrupt the process or the system may not function properly.

Follow these instructions to upgrade the BIOS using the ISO Image BIOS file:

1. Download the ISO Image BIOS file.

2. Using software capable of uncompressing and writing an ISO image file to CD, burn

the data to a blank CD.

NOTE

Copying the ISO Image BIOS file to CD will not work. The completed CD should
contain multiple files and a directory.

3. Insert the CD that was created in the CD-ROM drive of the computer to be

upgraded and boot the system.

4. When the "Press ENTER to continue booting from CD-ROM" prompt appears, press

the Enter key. The system will boot from the hard drive if no key is pressed within
15 seconds.

5. At the "Welcome to the Intel Desktop Board BIOS Upgrade CD-ROM" page, press

any key to confirm the BIOS upgrade operation.

6. Wait for the BIOS upgrade process to complete.

CAUTION

DO NOT POWER DOWN YOUR COMPUTER before the update is complete. The update
may take up to 5 minutes.

Updating the BIOS with the Iflash Memory Update
Utility

With the Iflash Memory update utility you can update the system BIOS from a
bootable CD-ROM, bootable USB flash drive, or other bootable USB media. The utility
available on the Intel World Wide Web site provides a simple method for creating a
bootable CD-ROM that will automatically update your BIOS. The Iflash BIOS update
files can also be extracted locally to your hard drive and copied to a bootable USB
flash drive or other bootable USB media.

The Iflash Memory update utility allows you to:

• Update the BIOS and Intel Management Engine in flash memory

• Update the language section of the BIOS

NOTE

Review the instructions distributed with the update utility before attempting a BIOS
update.

65

Intel Desktop Board D5400XS Product Guide

CAUTION

Do not interrupt the process or the system may not function properly.

1. Uncompress the BIOS update file and copy the .BIO file, IFLASH.EXE, and .ITK file

(optional) to a bootable USB flash drive or other bootable USB media.

2. Configure the BIOS or use the F10 option during POST to boot to the USB device.

3. Manually run the IFLASH.EXE file from the USB device and manually update the

BIOS.

Recovering the BIOS

It is unlikely that anything will interrupt the BIOS update; however, if an interruption
occurs, the BIOS could be damaged. Due to BIOS size and recovery requirements, a
CD-R with the .BIO file in the root directory will be required.

Related Links

For more information about updating the Intel Desktop Board BIOS or recovering from
a BIOS update failure, go to

http://support.intel.com/support/motherboards/desktop

/sb/CS-022312.htm.

66

4 Configuring for RAID

Configuring for RAID Using Intel® Matrix
Storage Technology

NOTE

Intel Matrix Storage Technology requires the Microsoft Windows Vista or Microsoft
Windows XP operating system and SATA hard drives.

Configuring the BIOS

1. Assemble your system and attach two or more SATA hard drives to the SATA

connectors.

2. Enter system BIOS Setup by pressing <F2> after the Power-On-Self-Test (POST)

memory tests begin.

3. Go to Advanced  Drive Configuration  Configure SATA as; ensure that

RAID is selected.

4. Then save your settings by pressing <F10>.

Creating Your RAID Set

1. Upon re-boot, you will see the following Intel Matrix Storage Manager option ROM

status message on the screen: Press <Ctrl-I> to enter the RAID
Configuration Utility. Press <Ctrl-I> and enter the RAID Configuration Utility.

2. In the Intel Matrix Storage Manager option ROM Main Menu, select option #1:

Create RAID Volume. Enter a volume name (using English alphanumeric ASCII
characters) and press <Enter>.

3. Use the arrow keys to select RAID 0 or RAID 1 (if only two SATA drives are

available), RAID 5 and RAID 10 (these options will only appear if three or four
SATA drives are installed). Press <Enter> once you have selected the RAID LEVEL.

4. Select the drives to be used in the RAID array (only if there are more than two

drives available) and press <Enter>.

5. Select the strip size, if necessary, and press <Enter>.

6. Enter the size of the volume (if you enter less than the maximum volume size, you

can then create a second RAID array on the remaining portion of your volume) and
press <Enter>.

7. Finally, press <Enter> to Create Volume.

8. Exit the Option ROM user interface by pressing <Esc> or going to the EXIT option

in the MAIN MENU.

67

Intel Desktop Board D5400XS Product Guide

Loading the Intel Matrix Storage Technology RAID
Drivers and Software

1. Begin Windows Setup by booting from the Windows installation CD.

2. At the beginning of Windows Setup, press <F6> to install a third-party SCSI or

RAID driver. When prompted, insert the diskette that contains the Intel Matrix
Storage Technology RAID Driver in a USB floppy disk drive. Refer to

http://support.microsoft.com/kb/916196/en-us

compatible USB floppy disk drive. Install the Intel

3. Finish the Windows installation and install all necessary drivers.

4. Install the Intel Matrix Storage Console software via the Intel Express Installer CD

included with your Desktop Board or after downloading it from the Desktop Board
D5400XS page at http://www.intel.com/products/motherboard/
Storage Console software can be used to manage the RAID configuration.

for information on selecting a

®

SATA RAID Controller driver.

. The Intel Matrix

Setting Up a “RAID Ready” System

The Intel Matrix Storage Technology Console software offers the flexibility to upgrade
from a single Serial ATA drive to RAID without reinstalling the operating system, when
a second SATA hard drive is added to the system.

Follow the steps described above in "Configuring the BIOS for Intel Matrix Storage
Technology" and "Loading the Intel Matrix Storage Technology RAID Drivers and
Software."

Once additional SATA drives have been added to the system, open the Intel Matrix
Storage Technology Console Software and follow the directions to update to a RAID
setup.

Configuring for External RAID Using Marvell
Storage Technology

Configuring the BIOS

1. Assemble your system and attach two eSATA hard drives to the Desktop Board’s

two back panel eSATA connectors.

2. Enter system BIOS Setup by pressing the <F2> key after the Power-On-Self-Test

(POST) memory tests begin.

3. Go to Advanced  Peripheral Configuration  Secondary SATA Controller;

ensure that RAID is selected.

4. Then save your settings by pressing <F10>.

68

Configuring for RAID

Creating Your RAID Set

1. Upon re-boot, you will see the following Marvell Storage Manager option ROM

status message on the screen: Press <Ctrl-M> to enter the RAID
Configuration Utility. Press <Ctrl-M> and enter the RAID Configuration
Utility.

2. In the Marvell Storage Manager option ROM Main Menu, select: Create RAID

Volume. Enter a volume name and press <Enter>.
NOTE: The RAID Volume name must be in English alphanumeric ASCII characters.

3. Use the arrow keys to select RAID 0 or RAID 1. Press <Enter> once you have

selected the RAID LEVEL.

4. Select the strip size, if necessary, and press <Enter>.

5. Enter the size of the volume (if you enter less than the maximum volume size, you

can then create a second RAID array on the remaining portion of your volume) and
press <Enter>.

6. Finally, press <Enter> to Create Volume.

7. Exit the Option ROM user interface by pressing <Esc> or going to the EXIT option

in the MAIN MENU.

Loading the Marvell Storage Technology RAID Drivers
and Software

1. Begin Windows Setup by booting from the Windows installation CD.

2. At the beginning of Windows Setup, press <F6> to install a third-party SCSI or

RAID driver. When prompted, insert the diskette that contains the Marvell Storage
Technology RAID Driver in a USB floppy disk drive. Refer to

http://support.microsoft.com/kb/916196/en-us

compatible USB floppy disk drive. Install the Marvell 88SE61XX SATA RAID
Controller driver.

3. Finish the Windows installation and install all necessary drivers.

for information on selecting a

69

Intel Desktop Board D5400XS Product Guide

70

A Error Messages and Indicators

Desktop Board D5400XS reports POST errors in three ways:

• By sounding a beep code

• By displaying an error message on the monitor

• By displaying diagnostic progress codes (POST codes)

BIOS Beep Codes

The BIOS also issues a beep code (one long tone followed by two short tones) during
POST if the video configuration fails (a faulty video card or no card installed) or if an
external ROM module does not properly checksum to zero. Table 14 lists the BIOS
codes.

Table 14.

Beep Description

3 No memory
Siren Processor overheat (on reboot)

Beep Codes

BIOS Error Messages

When a recoverable error occurs during the POST, the BIOS displays an error message
describing the problem. Table 15 gives an explanation of

Table 15. BIOS Error Messages

Error Message Explanation

PROCESSOR_THERMAL_TRIP_ERROR

MULTI_BIT_ECC_ERROR The firmware has detected that a Multi-Bit ECC Error occurred.
SINGLE_BIT_ECC_ERROR

CMOS_BATTERY_ERROR

CMOS_CHECKSUM_ERROR

CMOS_TIMER_ERROR

MEMORY_SIZE_DECREASE_ERROR

INTRUDER_DETECTION_ERROR The system chassis was opened.

Processor was previously shutdown due to a thermal event
(overheating).

The firmware has detected that a Single-Bit ECC Error
occurred.

The firmware has detected that a CMOS battery failure
occurred.

The firmware has detected that a CMOS Checksum Error
occurred.

The firmware has detected that the system date/time has not
been set.

The firmware has detected that the system memory has
decreased.

the BIOS error messages.

71

Intel Desktop Board D5400XS Product Guide

Port 80h POST Codes

During the POST, the BIOS generates diagnostic progress codes (POST codes) to I/O
port 80h. If the POST fails, execution stops and the last POST code generated is left
at port 80h and displayed on the Desktop Board’s seven-segment LED display shown
in Figure 29. This code is useful for determining the point where an e
during the POST.

rror occurred

72

Figure 29. POST Code Indicators

Error Messages and Indicators

Table 16 lists the Port 80h POST codes in hexadecimal notation.

Table 16. Port 80h POST Codes

POST Code Description of POST Operation

Host Processor

10 Power-on initialization of the host processor (Boot Strap Processor)

11 Host processor cache initialization (including APs)

12 Starting Application processor initialization

13 SMM initialization

Chipset

21 Initializing a chipset component

Memory

22 Reading SPD from memory DIMMs

23 Detecting presence of memory DIMMs

24 Programming timing parameters in the memory controller and the DIMMs

25 Configuring memory

26 Optimizing memory settings

27 Initializing memory, such as ECC init

29 Memory testing completed

PCI Bus

50 Enumerating PCI buses

51 Allocating resources to the PCI bus

52 Hot Plug PCI controller initialization

53 – 57 Reserved for the PCI bus

USB

58 Resetting the USB bus

59 Reserved for the USB bus

ATA/ATAPI/SATA

5A Resetting the PATA/SATA bus and all devices

5B Reserved for ATA

SMBus
5C Resetting the SMBus
5D Reserved for the SMBus

Local Console
70 Resetting the VGA controller

71 Disabling the VGA controller
72 Enabling the VGA controller

Remote Console
78 Resetting the console controller

79 Disabling the console controller
7A Enabling the console controller

continued

73

Intel Desktop Board D5400XS Product Guide

Table 16. Port 80h POST Codes (continued)

POST Code Description of POST Operation

Keyboard (USB)
90 Resetting the keyboard

91 Disabling the keyboard
92 Detecting presence of a keyboard
93 Enabling the keyboard
94 Clearing the keyboard input buffer
95 Instructing the keyboard controller to run Self Test (PS/2 only)

Mouse (USB)
98 Resetting the mouse

99 Disabling the mouse
9A Detecting presence of a mouse
9B Enabling the mouse

Fixed Media
B0 Resetting fixed media
B1 Disabling fixed media

B2 Detecting presence of fixed media (IDE hard drive detection, etc)
B3 Enabling/configuring fixed media

Removable Media
B8 Resetting removable media

B9 Disabling removable media
BA Detecting presence of removable media (IDE, CD-ROM detection, etc)
BC Enabling/configuring removable media

BDS
Dy Trying boot selection y (y=0 to 15)

PEI Core
E0 Started dispatching PEIMs (emitted on first report of EFI_SW_PC_INIT_BEGIN

EFI_SW_PEI_PC_HANDOFF_TO_NEXT)
E2 Permanent memory found
E1, E3 Reserved for PEI/PEIMs

DXE Core

E4 Entered DXE phase
E5 Started dispatching drivers
E6 Started connecting drivers

continued

74

Error Messages and Indicators

Table 16. Port 80h POST Codes (continued)

POST Code Description of POST Operation

DXE Drivers

E7 Waiting for user input
E8 Checking the password
E9 Entering BIOS setup
EB Calling Legacy Option ROMs

Runtime Phase/EFI Operating System Boot

F4 Entering Sleep state
F5 Exiting Sleep state
F8 EFI boot service ExitBootServices( ) has been called
F9 EFI runtime service SetVirtualAddressMap( ) has been called
FA EFI runtime service ResetSystem( ) has been called

PEIMs/Recovery/Wake

30 Wake from S3
31 Crisis Recovery has initiated by software (corrupt Flash memory)
34 Loading the recovery capsule
35 Handing off control to the recovery capsule
3F Unable to recover
40 Wake from S4

75

Intel Desktop Board D5400XS Product Guide

76

B Regulatory Compliance

This appendix contains the following regulatory compliance information for Desktop
Board D5400XS:

• Safety standards

• European Union Declaration of Conformity statement

• Product Ecology statements

• Electromagnetic Compatibility (EMC) regulations

• Product certifications

Safety Standards

Desktop Board D5400XS complies with the safety standards stated in Table 17 when
correctly installed in a compatible host system.

Table 17. Safety Standards

Regulation Title

CSA/UL 60950-1, First
Edition

EN 60950-1:2006, Second
Edition

IEC 60950-1:2005, Second
Edition

Information Technology Equipment – Safety - Part 1: General
Requirements (USA and Canada)

Information Technology Equipment – Safety - Part 1: General
Requirements (European Union)

Information Technology Equipment – Safety - Part 1: General
Requirements (International)

Place Battery Marking

There is insufficient space on this Desktop Board to provide instructions for replacing
and disposing of the Lithium ion coin cell battery. For system safety certification, the
statement below or an equivalent statement is required to be permanently and legibly
marked on the chassis near the battery.

CAUTION

Risk of explosion if the battery is replaced with an incorrect type. Batteries should be
recycled where possible. Disposal of used batteries must be in accordance with local
environmental regulations.

A suitable caution label is included with Desktop Board D5400XS.

Related Links

For information about replacing the battery, go to page 57.

77

Intel Desktop Board D5400XS Product Guide

European Union Declaration of Conformity
Statement

We, Intel Corporation, declare under our sole responsibility that the product Intel®
Desktop Board D5400XS is in conformity with all applicable essential requirements
necessary for CE marking, following the provisions of the European Council Directives
2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive).

The product is properly CE marked demonstrating this conformity and is for
distribution within all member states of the EU with no restrictions.

This product follows the provisions of the European Directives 2004/108/EC and
2006/95/EC.

Čeština Tento výrobek odpovídá požadavkům evropských směrnic 2004/108/EC a
2006/95/EC.

Dansk Dette produkt er i overensstemmelse med det europæiske direktiv
2004/108/EC & 2006/95/EC.

Dutch Dit product is in navolging van de bepalingen van Europees Directief
2004/108/EC & 2006/95/EC.

Eesti Antud toode vastab Euroopa direktiivides 2004/108/EC ja 2006/95/EC
kehtestatud nõuetele.

Suomi Tämä tuote noudattaa EU-direktiivin 2004/108/EC & 2006/95/EC määräyksiä.
Français Ce produit est conforme aux exigences de la Directive Européenne

2004/108/EC & 2006/95/EC.
Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie

2004/108/EC & 2006/95/EC.
Ελληνικά Το παρόν προϊόν ακολουθεί τις διατάξεις των Ευρωπαϊκών Οδηγιών

2004/108/EC και 2006/95/EC.
Magyar E termék megfelel a 2004/108/EC és 2006/95/EC Európai Irányelv

előírásainak.
Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer

2004/108/EC & 2006/95/EC.
Italiano Questo prodotto è conforme alla Direttiva Europea 2004/108/EC &

2006/95/EC.
Latviešu Šis produkts atbilst Eiropas Direktīvu 2004/108/EC un 2006/95/EC

noteikumiem.

78

Regulatory Compliance

Lietuvių Šis produktas atitinka Europos direktyvų 2004/108/EC ir 2006/95/EC
nuostatas.

Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej
2004/108/EC u 2006/95/EC.

Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet
2004/108/EC & 2006/95/EC.

Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej
2004/108/EC i 2006/95/EC.

Portuguese Este produto cumpre com as normas da Diretiva Européia 2004/108/EC
& 2006/95/EC.

Español Este producto cumple con las normas del Directivo Europeo 2004/108/EC &
2006/95/EC.

Slovensky Tento produkt je v súlade s ustanoveniami európskych direktív
2004/108/EC a 2006/95/EC.

Slovenščina Izdelek je skladen z določbami evropskih direktiv 2004/108/EC in
2006/95/EC.

Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 2004/108/EC &
2006/95/EC.

Türkçe Bu ürün, Avrupa Birliği’nin 2004/108/EC ve 2006/95/EC yönergelerine uyar.

Product Ecology Statements

The following information is provided to address worldwide product ecology concerns
and regulations.

Recycling Considerations

As part of its commitment to environmental responsibility, Intel has implemented the

®

Intel

Product Recycling Program to allow retail consumers of Intel’s branded products

to return used products to selected locations for proper recycling.
Please consult http://www.intel.com/intel/other/ehs/product_ecology

for the details of this program, including the scope of covered products, available
locations, shipping instructions, terms and conditions, etc.

中文

作为其对环境责任之承诺的部分，英特尔已实施 Intel Product Recycling Program
（英特尔产品回收计划），以允许英特尔品牌产品的零售消费者将使用过的产品退还至指定地点作恰
当的重复使用处理。

请参考http://www.intel.com/intel/other/ehs/
了解此计划的详情，包括涉及产品之范围、回收地点、运送指导、条款和条件等。

product_ecology

79

Intel Desktop Board D5400XS Product Guide

Deutsch

Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel
Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel
Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für
ordnungsgemäßes Recycling zurückzugeben.

Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte,
verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der

http://www.intel.com/intel/other/ehs/product_ecology

Español

Como parte de su compromiso de responsabilidad medioambiental, Intel ha
implantado el programa de reciclaje de productos Intel, que permite que los
consumidores al detalle de los productos Intel devuelvan los productos usados en los
lugares seleccionados para su correspondiente reciclado.

Consulte la http://www.intel.com/intel/other/ehs/product_ecology
para ver los detalles del programa, que incluye los productos que abarca, los lugares
disponibles, instrucciones de envío, términos y condiciones, etc.

Français

Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis
en œuvre le programme Intel Product Recycling Program (Programme de recyclage
des produits Intel) pour permettre aux consommateurs de produits Intel de recycler
les produits usés en les retournant à des adresses spécifiées.

Visitez la page Web http://www.intel.com/intel/other/ehs/product_ecology

pour en
savoir plus sur ce programme, à savoir les produits concernés, les adresses
disponibles, les instructions d'expédition, les conditions générales, etc.

日本語

インテルでは、環境保護活動の一環として、使い終えたインテル
ブランド製品を指定の場所へ返送していただき、リサイクルを適切に行えるよう、インテル製品リサイクル
プログラムを発足させました。

対象製品、返送先、返送方法、ご利用規約など、このプログラムの詳細情報は、http://www.intel.com/in

tel/other/ehs/product_ecology （英語）をご覧ください。

Malay

Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran,
Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan
pengguna-pengguna runcit produk jenama Intel memulangkan produk terguna ke
lokasi-lokasi terpilih untuk dikitarkan semula dengan betul.

Sila rujuk http://www.intel.com/intel/other/ehs/product_ecology
butir-butir program ini, termasuklah skop produk yang dirangkumi, lokasi-lokasi
tersedia, arahan penghantaran, terma & syarat, dsb.

80

untuk mendapatkan

Regulatory Compliance

Portuguese

Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o
Programa de Reciclagem de Produtos para que os consumidores finais possam enviar
produtos Intel usados para locais selecionados, onde esses produtos são reciclados de
maneira adequada.

Consulte o site http://www.intel.com/intel/other/ehs/product_ecology

(em Inglês) para

obter os detalhes sobre este programa, inclusive o escopo dos produtos cobertos, os
locais disponíveis, as instruções de envio, os termos e condições, etc.

Russian

В качестве части своих обязательств к окружающей среде, в Intel создана
программа утилизации продукции Intel (Product Recycling Program) для
предоставления конечным пользователям марок продукции Intel возможности
возврата используемой продукции в специализированные пункты для должной
утилизации.

Пожалуйста, обратитесь на веб-сайт

http://www.intel.com/intel/other/ehs/product_ecology

за информацией об этой

программе, принимаемых продуктах, местах приема, инструкциях об отправке,
положениях и условиях и т.д.

Türkçe

Intel, çevre sorumluluğuna bağımlılığının bir parçası olarak, perakende tüketicilerin
Intel markalı kullanılmış ürünlerini belirlenmiş merkezlere iade edip uygun şekilde geri
dönüştürmesini amaçlayan Intel Ürünleri Geri Dönüşüm Programı’nı uygulamaya
koymuştur.

Bu programın ürün kapsamı, ürün iade merkezleri, nakliye talimatları, kayıtlar ve
şartlar v.s dahil bütün ayrıntılarını ögrenmek için lütfen

http://www.intel.com/intel/other/ehs/product_ecology

web sayfasına gidin.

81

Intel Desktop Board D5400XS Product Guide

Lead-free 2LI/Pb-free 2LI Board

The electronics industry is transitioning to European Union (EU) Restriction of
Hazardous Substances (RoHS)-compliant products. The RoHS legislation restricts the
use of six materials. One of these restricted materials is lead. Lead is the most
common and problematic of the RoHS restricted materials.

There are exemptions in RoHS that allow the use of lead in some very limited locations
in electronic products. Maximum lead concentration values have been established for
RoHS-compliant electronic products that allow up to 1000 ppm of lead.

Lead-free/Pb-free is a nickname that is often used (or misused) for RoHS-compliant
products. In this case, the term "Lead-free/Pb-free" means that lead has been
removed where required by the RoHS legislation but still may exist as an impurity
below 1000 ppm.

The term "Lead-free 2LI/Pb-free 2LI" means lead-free second level interconnect (2LI).
The balls, leads, or pads used to connect a component to a printed circuit board are
lead-free, but the first level interconnect (FLI) is not lead-free. The use of lead in the
FLI is acceptable because of the RoHS "flip chip" or "die bump" interconnect
exemption.

Desktop Board D5400XS is a lead-free second level interconnect product. Table 18
shows
accompanying collateral. These marks are based on IPC/JEDEC standard J-STD-609,

Marking and Labeling of Components, PCBs and PCBAs to Identify Lead, Lead Free and
Other Attributes.

For more information concerning Intel’s lead-free initiatives, refer to:

http://www.intel.com/technology/silicon/leadfree.htm

the lead-free second level interconnect marks as they appear on the board and

.

82

Table 18. Lead-Free Second Level Interconnect Marks

Description Mark

This symbol is used to identify
electrical and electronic
assemblies and components in
which the Pb concentration
level in the Desktop Board
substrate and the solder
connections from the board to
the components (second-level
interconnect) is not greater
than 0.1% by weight
(1000 ppm).

or

Regulatory Compliance

or

Restriction of Hazardous Substances (RoHS)

EU RoHS

EU RoHS Directive 2002/95/EC restricts the use of the following six materials in
various types of electronic and electrical equipment:

• Lead

• Mercury

• Cadmium

• Hexavalent chromium

• Polybrominated biphenyls (PBB)

• Polybrominated diphenyl ether (PBDE)

The maximum concentrations allowed are 0.1% or 1000 ppm (except for cadmium,
which is limited to 0.01% or 100 ppm) by weight of homogeneous material.

Desktop Board D5400XS complies with these restrictions.

83

Intel Desktop Board D5400XS Product Guide

China RoHS

“China RoHS” is the term used by industry generally to describe legislation
implemented by the Ministry of Information Industry (MII) in the People's Republic of
China for the control of pollution by electronic information products (EIP). The official
title of the China RoHS regulation is Management Methods for Controlling Pollution by
Electronic Information Products.

China RoHS bans the same substances and has the same limits as EU RoHS.
However, the China RoHS regulation requires specific product marking and a self­declaration of the controlled substances contained in each product.

Desktop Board D5400XS is a China RoHS-compliant product.
The required China RoHS mark indicates the product’s Environmental Friendly Usage

Period (EFUP). The EFUP is defined as the number of years for which listed controlled
substances will not leak or chemically deteriorate while in the product. The EFUP for
Intel Desktop Boards has been determined to be 10 years.

The China RoHS EFUP mark for Desktop Board D5400XS is shown in Table 19.

Table 19.

Description Mark

This is an example of the
symbol used on Intel Desktop
Boards and associated
collateral. The color of the
mark may vary depending
upon the application. The
Environmental Friendly Usage
Period (EFUP) for Intel
Desktop Boards has been
determined to be 10 years.

China RoHS Environmentally Friendly Use Period Mark

The China MII also stipulates that a material Self Declaration Table (SDT) must be
included in a product’s user documentation. The SDT for Desktop Board D5400XS is
shown in Figure 30.

84

Regulatory Compliance

Figure 30. Desktop Board D5400XS China RoHS Material

Self Declaration Table

85

Intel Desktop Board D5400XS Product Guide

EMC Regulations

Desktop Board D5400XS complies with the EMC regulations stated in Table 20 when
correctly installed in a compatible host system.

Table 20. EMC Regulations

Regulation (Class B) Title

FCC 47 CFR Part 15,
Subpart B

ICES-003 Issue 4 Interference-Causing Equipment Standard, Digital Apparatus.

EN55022:2006 Limits and methods of measurement of Radio Interference

EN55024:1998 Information Technology Equipment – Immunity Characteristics

EN55022:2006 Australian Communications Authority, Standard for

CISPR 22:2005
+A1:2005 +A2:2006

CISPR 24:1997
+A1:2001 +A2:2002

VCCI V-3/2007.04,
V-4/2007.04

Japanese Kanji statement translation: This is a Class B product based on the standard
of the Voluntary Control Council for Interference from Information Technology
Equipment (VCCI). If this is used near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and use the equipment
according to the instruction manual.

Title 47 of the Code of Federal Regulations, Part 15, Subpart B,
Radio Frequency Devices. (USA)

(Canada)

Characteristics of Information Technology Equipment. (European
Union)

Limits and methods of measurement. (European Union)

Electromagnetic Compatibility. (Australia and New Zealand)
Limits and methods of measurement of Radio Disturbance

Characteristics of Information Technology Equipment.
(International)

Information Technology Equipment – Immunity Characteristics –
Limits and Methods of Measurement. (International)

Voluntary Control for Interference by Information Technology
Equipment (Japan)

86

Regulatory Compliance

Korean Class B statement translation: This is household equipment that is certified to
comply with EMC requirements. You may use this equipment in residential
environments and other non-residential environments.

Ensure Electromagnetic Compatibility (EMC)
Compliance

Before computer integration, make sure that the power supply and other modules or
peripherals, as applicable, have passed Class B EMC testing and are marked
accordingly.

Pay close attention to the following when reading the installation instructions for the
host chassis, power supply, and other modules:

• Product certifications or lack of certifications

• External I/O cable shielding and filtering

• Mounting, grounding, and bonding requirements

• Keying connectors when mating the wrong connectors could be hazardous

If the power supply and other modules or peripherals, as applicable, are not Class B
EMC compliant before integration, then EMC testing may be required on a
representative sample of the newly completed computer.

87

Intel Desktop Board D5400XS Product Guide

Product Certifications

Board-Level Certification Markings

Desktop Board D5400XS has the product certification markings shown in Table 21.

Table 21. Product Certification Markings

Description Mark

UL joint US/Canada Recognized Component mark. Includes adjacent
UL file number for Intel Desktop Boards: E210882.

FCC Declaration of Conformity logo mark for Class B equipment.
Includes Intel name and D5400XS model designation.

CE mark. Declaring compliance to European Union (EU) EMC
directive and Low Voltage directive.

Australian Communications Authority (ACA) and New Zealand Radio
Spectrum Management (NZ RSM) C-tick mark. Includes adjacent
Intel supplier code number, N-232.

Japan VCCI (Voluntary Control Council for Interference) mark.

S. Korea MIC (Ministry of Information and Communication) mark.
Includes adjacent MIC certification number: CPU-D5400XS (B).

Taiwan BSMI (Bureau of Standards, Metrology and Inspections)
mark. Includes adjacent Intel company number, D33025.

Printed wiring board manufacturer’s recognition mark. Consists of a
unique UL recognized manufacturer’s logo, along with a flammability
rating (solder side).

V-0

88

Regulatory Compliance

Chassis and Component Certifications

Ensure that the chassis and certain components; such as the power supply, peripheral
drives, wiring, and cables; are components certified for the country or market where
used. Agency certification marks on the product are proof of certification. Typical
product certifications include:

In Europe
The CE marking signifies compliance with all applicable European requirements. If the
chassis and other components are not properly CE marked, a supplier’s Declaration of
Conformity statement to the European EMC directive and Low Voltage directive (as
applicable), should be obtained. Additionally, other directives, such as the Radio and
Telecommunications Terminal Equipment (R&TTE) directive may also apply depending
on product features.

In the United States
A certification mark by a Nationally Recognized Testing Laboratory (NRTL) such as UL,
CSA, or ETL signifies compliance with safety requirements. Wiring and cables must
also be UL listed or recognized and suitable for the intended use. The FCC Class B
logo for home or office use signifies compliance with electromagnetic interference
(EMI) requirements.

In Canada
A nationally recognized certification mark such as CSA or cUL signifies compliance with
safety requirements. The Industry Canada statement at the front of this product guide
demonstrates compliance with Canadian EMC regulations.

89

Intel Desktop Board D5400XS Product Guide

90