Intel® Storage System SSR316MJ2
Cable Kit (FMJCABLES2)
Installation Guide
Order Number: D27073-002
Disclaimer
Information in this document is provided in connection with Intel
otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions
of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating
to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability,
or infringement of any patent, copyright or other intellectual property right. Intel products are not designed, intended or
authorized for use in any medical, life saving, or life sustaining applications or for any other application in which the failure of
the Intel
product could create a situation where personal injury or death may occur. Intel may make changes to
specifications and product descriptions at any time, without notice.
Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
*
Other names and brands may be claimed as the property of others.
Copyright © 2004 - 2005 Intel Corporation. All Rights Reserved.
ii Intel® Storage System SSR316MJ2 Cable Kit
®
products. No license, express or implied, by estoppel or
Important Safety Instructions
Important Safety Instructions
Read all caution and safety statements in this document before performing any of the instructions.
See Intel Server Boards and Server Chassis Safety Information at
http://support.intel.com/support/motherboards/server/sb/CS-010770.htm.
Wichtige Sicherheitshinweise
Lesen Sie zunächst sämtliche Warn- und Sicherheitshinweise in diesem Dokument, bevor Sie eine
der Anweisungen ausführen. Beachten Sie hierzu auch die Sicherheitshinweise zu IntelServerplatinen und -Servergehäusen unter
http://support.intel.com/support/motherboards/server/sb/CS-010770.htm.
重要安全指导
在执行任何指令之前，请阅读本文档中的所有注意事项及安全声明。
和/或
http://support.intel.com/support/motherboards/server/sb/CS-010770.htm 上的
Server Boards and Server Chassis Safety Information
服务器主板与服务器机箱安全信息》）。
（《Intel
Consignes de sécurité
Lisez attention toutes les consignes de sécurité et les mises en garde indiquées dans ce document
avant de suivre toute instruction. Consultez Intel Server Boards and Server Chassis Safety
Information rendez-vous sur le site
010770.htm.
http://support.intel.com/support/motherboards/server/sb/CS-
Instrucciones de seguridad importantes
Lea todas las declaraciones de seguridad y precaución de este documento antes de realizar
cualquiera de las instrucciones. Vea Intel Server Boards and Server Chassis Safety Information en
http://support.intel.com/support/motherboards/server/sb/CS-010770.htm.
Intel
Intel® Storage System SSR316MJ2 Cable Kit iii
WARNINGS
Storage system power on/off: The push-button on/off power switch on the
front panel of the storage system does not turn off the AC power. To remove
AC power from the storage system, you must unplug the AC power cord
from either the power supply or wall outlet.
Hazardous conditions—power supply: Hazardous voltage, current, and
energy levels are present inside the power supply enclosure. There are no
user-serviceable parts inside the power supply; servicing should only be done
by technically qualified personnel.
Hazardous conditions—devices and cables: Hazardous electrical
conditions may be present on power, telephone, and communication cables.
Turn off the storage system and disconnect telecommunications systems,
networks, modems, and the power cord attached to the storage system before
opening it. Failure to do so can result in personal injury or equipment
damage.
Avoid injury: Lifting the storage system chassis and attaching it to the rack
is a two-person job. If needed, use an appropriate lifting device. A fully
loaded Intel® Storage System SSR316MJ2 weighs approximately 31.8 kg
(70 lbs.).
CAUTIONS
Temperature: The operating temperature of the storage system, when
installed in an equipment rack, must not go below 5° C (41° F) or rise above
35° C (95° F). Extreme fluctuations in temperature can cause a variety of
problems in the storage system.
Ventilation: The equipment rack must provide sufficient airflow to the front
of the storage system to maintain proper cooling. It must also include
ventilation sufficient to exhaust a maximum of 1900 BTUs per hour for a
fully loaded Intel® Storage System SSR316MJ2.
Intel® Storage System SSR316MJ2 Cable Kit iv
Contents
About the Cable Kit ............................................................................................. 9
Kit Contents............................................................................................................................. 9
SATA Cables Installation Procedures............................................................. 10
Required Tools...................................................................................................................... 10
Power Down System and Remove Chassis Cover ...............................................................10
Unseat Hard Disk Drive Carriers........................................................................................... 11
Disconnect Front Panel Cables............................................................................................. 12
Remove Fan Assembly Screws ............................................................................................ 13
Disconnect Fan Cables ......................................................................................................... 14
Remove Fan Assembly and Disconnect SATA Cables......................................................... 15
Disconnect I
Disconnect Power Distribution Module Cables ..................................................................... 17
Cut SATA Cable Ties............................................................................................................ 18
Remove Backplane Board ....................................................................................................19
Remove Backplane Board from Housing ..............................................................................20
Connect SATA Cables and Attach Backplane Board to Housing .........................................21
Connect I
Connect Power Distribution Module Cables.......................................................................... 23
Install Backplane Board ........................................................................................................24
Connect SATA Cables .......................................................................................................... 25
Install Fan Assembly............................................................................................................. 26
Attach Fan Assembly ............................................................................................................ 27
Connect System Fan Cables ................................................................................................28
Connect Front Panel Board Cables ......................................................................................29
Seat Hard Disk Drive Carriers............................................................................................... 30
Finishing Up .......................................................................................................................... 31
2
C Cables........................................................................................................... 16
2
C Cables............................................................................................................... 22
Front Panel Cables Installation Procedures................................................... 32
Required Tools...................................................................................................................... 32
Power Down System and Remove Chassis Cover ...............................................................32
Disconnect Front Panel Cables from Front Panel Board ...................................................... 33
Disconnect Front Panel Cables from Server Board .............................................................. 34
Connect New Front Panel Cables to Server Board............................................................... 35
Connect Front Panel Board Cables to Front Panel Board .................................................... 36
Finishing Up .......................................................................................................................... 37
2
I
C Cables Installation Procedures .................................................................. 38
Required Tools...................................................................................................................... 38
Power Down System and Remove Chassis Cover ...............................................................38
Disconnect Front Panel Cables............................................................................................. 39
Remove Fan Assembly Screws ............................................................................................ 40
Disconnect Fan Cables ......................................................................................................... 41
Remove Fan Assembly ......................................................................................................... 42
Intel® Storage System SSR316MJ2 Cable Kit v
Disconnect I
Connect I
2
C Cables........................................................................................................... 43
2
C Cables............................................................................................................... 44
Install Fan Assembly............................................................................................................. 45
Attach Fan Assembly ............................................................................................................ 46
Connect System Fan Cables ................................................................................................47
Connect Front Panel Board Cables ......................................................................................48
Finishing Up .......................................................................................................................... 49
Intel® Storage System SSR316MJ2 Cable Kit vi
Figures
Figure 1. Removing Chassis Cover ......................................................................................10
Figure 2. Unseating Hard Disk Carriers ................................................................................ 11
Figure 3. Disconnecting Front Panel Cables......................................................................... 12
Figure 4. Removing System Fan Assembly Screws ............................................................. 13
Figure 5. Disconnecting System Fan Cables ........................................................................14
Figure 6. Removing System Fan Assembly and Disconnecting SATA Cables..................... 15
Figure 7. Disconnecting I
Figure 8. Disconnecting Power Distribution Module Cables ................................................. 17
Figure 9. Cutting SATA Cable Ties ....................................................................................... 18
Figure 10. Removing Backplane Board ................................................................................19
Figure 11. Removing the Backplane Board from the Metal Housing .................................... 20
Figure 12. Installing New Backplane Board into Metal Shroud ............................................. 21
Figure 13. Connecting I
Figure 14. Connecting Power Distribution Module Cables.................................................... 23
Figure 15. Installing New Backplane Board .......................................................................... 24
Figure 16. Connecting SATA Cables .................................................................................... 25
Figure 17. Installing System Fan Assembly .......................................................................... 26
Figure 18. Attaching System Fan Assembly ......................................................................... 27
Figure 19. Connecting System Fan Cables ..........................................................................28
Figure 20. Connecting Front Panel Board Cables ................................................................29
Figure 21. Seating Hard Disk Drives..................................................................................... 30
Figure 22. Installing the Chassis Cover ................................................................................31
Figure 23. Removing Chassis Cover ....................................................................................32
Figure 24. Disconnecting Front Panel Cables....................................................................... 33
Figure 25. Disconnecting Front Panel Cables....................................................................... 34
Figure 26. Connecting Front Panel Cables to Server Board................................................. 35
Figure 27. Connecting Front Panel Board Cables ................................................................36
Figure 28. Installing the Chassis Cover ................................................................................37
Figure 29. Removing Chassis Cover ....................................................................................38
Figure 30. Disconnecting Front Panel Cables....................................................................... 39
Figure 31. Removing System Fan Assembly Screws ........................................................... 40
Figure 32. Disconnecting System Fan Cables...................................................................... 41
Figure 33. Removing System Fan Assembly ........................................................................42
Figure 34. Disconnecting I
Figure 35. Connecting I
Figure 36. Installing System Fan Assembly .......................................................................... 45
Figure 37. Attaching System Fan Assembly ......................................................................... 46
Figure 38. Connecting System Fan Cables ..........................................................................47
Figure 39. Connecting Front Panel Board Cables ................................................................48
Figure 40. Installing the Chassis Cover ................................................................................49
2
C Cables....................................................................................... 16
2
C Cables ......................................................................................... 22
2
C Cables..................................................................................... 43
2
C Cables ......................................................................................... 44
Intel® Storage System SSR316MJ2 Cable Kit vii
Intel® Storage System SSR316MJ2 Cable Kit viii
About the Cable Kit
Enclosed is your new Intel® FMJCABLES2 Cable Kit. This document describes how to install the
cables included in this kit into the Intel
®
Storage System SSR316MJ2.
Kit Contents
The FMJCABLES2 Cable Kit consists of the following:
One bundle of four 21-inch SATA cables, type A
One bundle of four 25-inch SATA cables, type B
One bundle of four 28-inch SATA cables, type C
One bundle of four 32-inch SATA cables, type D
Two Intel® FMJCABLES2 IDE cables
One Intel® FMJCABLES2 Front Panel cable
Two Intel® FMJCABLES2 I
2
C cables
Intel® Storage System SSR316MJ2 Cable Kit 9
SATA Cables Installation Procedures
SATA Cables Installation Procedures
Required Tools
Cross-head (Number 1 Size Phillips*) screwdriver
Wire cutters
Power Down System and Remove Chassis Cover
1. Review the safety information and warnings at the beginning of this guide.
2. Power down your Intel® Storage System Console. See letter “A” in
3. Remove both AC power cords from the AC power inputs at the rear of your storage system.
See letter “B” in
Figure 1.
4. Loosen the two thumb screws at the rear of the chassis cover. See letter “C” in
5. Facing the front of the chassis, push the top cover rearward, and then lift it up to remove it. See
letter “D” in
Figure 1.
Figure 1.
Figure 1.
B
C
D
C
A
®
Intel
Storage System SSR316MJ2 Cable Kit 10
Figure 1. Removing Chassis Cover
TP01797
SATA Cables Installation Procedures
Unseat Hard Disk Drive Carriers
CAUTION
The steps below do not require removing hard disk drive carriers from
the storage system. You need only disengage the carriers. If you choose
to remove the drive carriers from the storage system, first note the
location of each drive carrier. You must later reinstall each drive carrier
into the same location from which it was removed. See the Intel
System SSR316MJ2 Quick Start User’s Guide for details.
1. Press down on the hard disk drive handle release mechanisms to unlatch the handle on the hard
disk drive carriers. See letter “A” in
Figure 2.
2. Rotate the hard disk drive and hard disk drive carrier handles downward. See letter “B” in
Figure 2.
3. Slide the hard disk drives and hard disk drive carriers at least halfway out of the hard disk drive
bays. See letter “C” in
Figure 2. It is not necessary to completely remove the hard disk drives
from the bays. See the caution message above.
®
Storage
A
B
C
TP01798
Figure 2. Unseating Hard Disk Carriers
®
Intel
Storage System SSR316MJ2 Cable Kit 11
SATA Cables Installation Procedures
Disconnect Front Panel Cables
1. Disconnect the front panel cable, labeled J1, from the front panel board. See letter “A” in
Figure 3.
2. Disconnect the secondary IDE cable, labeled J3, from the front panel board. See letter “B” in
Figure 3.
3. Disconnect the primary IDE cable, labeled J5, from the front panel board. See letter “C” in
Figure 3.
4. Disconnect the front panel power connector from the front panel board. See letter “D” in
Figure 3.
A
B
C
Figure 3. Disconnecting Front Panel Cables
D
TP01799
®
Intel
Storage System SSR316MJ2 Cable Kit 12
SATA Cables Installation Procedures
Remove Fan Assembly Screws
Use a Number 1 size Phillips* screwdriver to remove the screw on each side of the system. See
letter “A” in
screws will be re-installed later.
Figure 4. These screws hold the system fan assembly in place. See Figure 4. These
A
Figure 4. Removing System Fan Assembly Screws
TP01800
®
Intel
Storage System SSR316MJ2 Cable Kit 13
SATA Cables Installation Procedures
Disconnect Fan Cables
1. Disconnect the Fan 3 cable from the server board. See letter “A” in Figure 5.
2. Disconnect the Fan 4 cable from the server board. See letter “B” in
3. Disconnect the Fan 5 cable from the server board. See letter “C” in
B
A
C
A
Figure 5.
Figure 5.
B
C
Figure 5. Disconnecting System Fan Cables
TP01801
®
Intel
Storage System SSR316MJ2 Cable Kit 14
SATA Cables Installation Procedures
Remove Fan Assembly and Disconnect SATA Cables
1. Simultaneously pull up on both sides of the system fan assembly to remove the fan assembly
from the storage system. See letter “A” in
surface.
2. Remove the 16 SATA cable connectors from the two SATA Host Bus Adapter cards located
inside the chassis at the rear of the system. See letter “B” in Figure 6.
A
Figure 6. Set the system fan assembly on a static-free
B
A
TP01802
Figure 6. Removing System Fan Assembly and Disconnecting SATA Cables
®
Intel
Storage System SSR316MJ2 Cable Kit 15
SATA Cables Installation Procedures
Disconnect I2C Cables
NOTE
The I2C cables are labeled at each end, on the cable connector. In the
instructions and the figure below, it is assumed that letter “A” corresponds to
your cable labeled JP4 and SL3_J13. Your connections may be different. It is
important that you write down the connections as they exist in your chassis,
so you may later correctly reconnect them.
In these steps, you do not need to disconnect the I
Bus Adapter cards. If you choose to disconnect the cables from the cards,
make sure you also write down these cable connections.
2
C cables from the Host
2
1. Write down the I
C cable connector positions on the backplane board. You will later need to re-
connect these cables to the same headers.
2. Disconnect the I
2
C cable that is labeled JP4 from the backplane board at the front of the chassis.
See letter “A” in the circled area of
3. Disconnect the I
circled area of
2
C cable that is labeled JP6 from the backplane board. See letter “B” in the
Figure 7.
Figure 7.
A
B
®
Intel
Storage System SSR316MJ2 Cable Kit 16
B
A
Figure 7. Disconnecting I2C Cables
TP01804
SATA Cables Installation Procedures
Disconnect Power Distribution Module Cables
Disconnect the two 12-pin power distribution module connectors from the backplane board. See
letter “A” in
Figure 8.
A
TP01805
Figure 8. Disconnecting Power Distribution Module Cables
®
Intel
Storage System SSR316MJ2 Cable Kit 17
SATA Cables Installation Procedures
Cut SATA Cable Ties
1. Note the routing for the SATA cables and the locations of the SATA cable ties. You will need
to install new cable ties in these locations later.
2. Cut the plastic cable ties that bundle the SATA cables. See letter “A” in
so you do not cut the SATA cables.
A
Figure 9. Use caution
Figure 9. Cutting SATA Cable Ties
TP01803
®
Intel
Storage System SSR316MJ2 Cable Kit 18
SATA Cables Installation Procedures
Remove Backplane Board
1. Use a Number 1 size Phillips screwdriver to remove the screws that hold the backplane board
to each side of the system. Two screws are at each side of the system. See letter “A” in
. Set these screws aside. They will be re-installed later.
10
2. Use a Number 1 size Phillips screwdriver to remove the four screws from the steel lip at the
bottom of the backplane board. See letter “B” in
re-installed later.
3. Lift the backplane board from the storage system. See letter “C” in
CAUTION
Use caution while lifting the backplane board so you do not cut yourself
on sharp edges.
Figure 10. Set these screws aside. They will be
Figure 10.
Figure
®
Intel
Storage System SSR316MJ2 Cable Kit 19
Figure 10. Removing Backplane Board
TP01806
SATA Cables Installation Procedures
Remove Backplane Board from Housing
1. Use a Number 1 size Phillips screwdriver to remove the two screws at each side of the
backplane board to release the backplane board from the metal housing. See letter “A” in
Figure 11. Set these screws aside. They will be re-installed later.
2. Remove the backplane board from the metal housing. See letter “B” in
CAUTION
Use caution while lifting the backplane board so you do not cut yourself
on sharp edges.
3. Remove all SATA cables from the backplane board. See letter “C” in
Figure 11.
Figure 11.
C
B
A
A
A
Figure 11. Removing the Backplane Board from the Metal Housing
A
A
®
Intel
Storage System SSR316MJ2 Cable Kit 20
SATA Cables Installation Procedures
Connect SATA Cables and Attach Backplane Board to
Housing
1. Open the SATA cables package that is part of the new FMJCABLES2 Cable Kit. Connect the
backplane board end of each of the 16 cables to the backplane board.
2. Carefully insert the new backplane board into the metal shroud. Pay attention to sharp edges on
the backplane board and metal shroud. See Figure 12.
3. Using a Number 1 size Phillips Screwdriver, screw in the two Phillips screws on each side of
the backplane board that hold the backplane board in its metal shroud. See Figure 12.
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
B
C
C
C
C
C
Figure 12. Installing New Backplane Board into Metal Shroud
A
0
®
Intel
Storage System SSR316MJ2 Cable Kit 21
SATA Cables Installation Procedures
Connect I2C Cables
NOTE
The I2C cables are labeled at each end, on the cable connector. In the
instructions and the figure below, it is assumed that letter “A” corresponds to
your cable labeled JP4 and SL3_J13. Your connections may be different.
Refer to the notes you made when you disconnected the cables to ensure you
are reconnecting them in the correct places.
1. Connect the I
area of
Figure 13.
2. Connect the I
area of
Figure 13.
2
C cable that is labeled JP4 to the backplane board. See letter “A” in the circled
2
C cable that is labeled JP6 to the backplane board. See letter “B” in the circled
A
B
B
A
®
Intel
Storage System SSR316MJ2 Cable Kit 22
Figure 13. Connecting I2C Cables
TP01822
SATA Cables Installation Procedures
Connect Power Distribution Module Cables
Connect the two 12-pin Power Distribution Module cables to the backplane board. See letter “A” in
Figure 14.
A
TP01808
Figure 14. Connecting Power Distribution Module Cables
®
Intel
Storage System SSR316MJ2 Cable Kit 23
SATA Cables Installation Procedures
Install Backplane Board
1. Align the holes on the bottom of the backplane board with the protruding blue pegs on the floor
of the chassis.
2. Push down to snap the backplane board into place. See letter “A” in
3. Use a Number 1 size Phillips screwdriver to install the four screws into the steel lip and the
backplane board. See letter “B” in
Figure 15.
4. Use a Number 1 size Phillips screwdriver to install two screws into each side of the system and
the backplane board. See letter “C” in
Figure 15.
Figure 15.
®
Intel
Storage System SSR316MJ2 Cable Kit 24
Figure 15. Installing New Backplane Board
TP01807
SATA Cables Installation Procedures
Connect SATA Cables
1. Connect the 16 SATA cables to the two SATA Host Bus Adapter cards located inside the
chassis at the rear of the system. See letter “A” in
2. Route the SATA cables along the side of the chassis in the same way that the original SATA
cables were routed.
3. Insert new plastic cable ties through the steel links on the side of the chassis. Bundle the SATA
cables into the cable ties and close the ties tightly around the cables. See letter “B” in
.
16
4. Bundle the SATA cables in other locations as necessary.
Figure 16.
Figure
®
Intel
Storage System SSR316MJ2 Cable Kit 25
Figure 16. Connecting SATA Cables
SATA Cables Installation Procedures
Install Fan Assembly
1. Move loose wires away from the space where the system fan assembly will be installed.
2. Align the holes on the bottom edge of the system fan assembly with the blue plastic shock
brackets on the bottom of the chassis.
3. Set the system fan assembly into place. See letter “A” in
A
Figure 17.
A
Figure 17. Installing System Fan Assembly
TP01811
®
Intel
Storage System SSR316MJ2 Cable Kit 26
SATA Cables Installation Procedures
Attach Fan Assembly
Use a Number 1 size Phillips screwdriver to attach the fan assembly to the chassis, using one screw
at each side of the system. See letter “A” in
Figure 18.
A
Figure 18. Attaching System Fan Assembly
TP01812
®
Intel
Storage System SSR316MJ2 Cable Kit 27
SATA Cables Installation Procedures
Connect System Fan Cables
1. Connect the Fan 3 cable to the server board. See letter “A” in Figure 19.
2. Connect the Fan 4 cable to the server board. See letter “B” in
3. Connect the Fan 5 cable to the server board. See letter “C” in
B
A
C
A
Figure 19.
Figure 19.
B
C
Figure 19. Connecting System Fan Cables
TP01813
®
Intel
Storage System SSR316MJ2 Cable Kit 28
SATA Cables Installation Procedures
Connect Front Panel Board Cables
1. Connect the front panel cable, labeled J1, to the front panel board. See letter “A” in Figure 20.
2. Connect the secondary IDE cable, labeled J3, to the front panel board. See letter “B” in
Figure 20. The secondary IDE cable has a white metal sheath and the connector on the front
panel is also white.
3. Connect the primary IDE cable, labeled J5, to the front panel board. The primary IDE cable has
a blue metal sheath and the connector on the front panel is also blue. See letter “C” in
Figure 20.
4. Connect the front panel power connector to the front panel board. See letter “D” in
Figure 20.
C
B
A
Figure 20. Connecting Front Panel Board Cables
D
TP01814
®
Intel
Storage System SSR316MJ2 Cable Kit 29
SATA Cables Installation Procedures
Seat Hard Disk Drive Carriers
1. Slide all sixteen hard disk drive carriers into the bays until they stop. See letter “A” in
Figure 21.
2. Push the handles up until they latch into place. See letter “B” in
Figure 21.
B
Figure 21. Seating Hard Disk Drives
A
TP01815
®
Intel
Storage System SSR316MJ2 Cable Kit 30
SATA Cables Installation Procedures
Finishing Up
1. Facing the front of the system, set the chassis cover into the corresponding slot in the chassis.
2. Pull the top cover forward. See letter “A” in
3. Tighten the two thumb screws at the rear of the chassis. See letter “B” in
4. Connect the AC power cables. See letter “C” in
5. Power on your Intel® Storage System Console. See letter “D” in
Figure 22.
Figure 22.
Figure 22.
Figure 22.
B
C
A
B
D
TP01816
Figure 22. Installing the Chassis Cover
®
Intel
Storage System SSR316MJ2 Cable Kit 31
Front Panel Cables Installation Procedures
Front Panel Cables Installation Procedures
Required Tools
Cross-head (Number 1 Size Phillips
Wire cutters
Power Down System and Remove Chassis Cover
1. Review the safety information and warnings at the beginning of this guide.
2. Power down your Intel® Storage System Console. See letter “A” in
3. Remove both AC power cords from the AC power inputs at the rear of your storage system.
See letter “B” in
4. Loosen the two thumb screws at the rear of the chassis cover. See letter “C” in
5. Facing the front of the chassis, push the top cover rearward, and then lift it up to remove it. See
letter “D” in
Figure 1.
Figure 1.
*
) screwdriver
Figure 1.
Figure 1.
B
C
D
C
A
®
Intel
Storage System SSR316MJ2 Cable Kit 32
Figure 23. Removing Chassis Cover
TP01797
Front Panel Cables Installation Procedures
Disconnect Front Panel Cables from Front Panel
Board
1. Note the routing of the front panel cables so you can later route the new cables in the same
way.
2. Disconnect the front panel cable, labeled J1, from the front panel board. See letter “A” in
Figure 3.
3. Disconnect the secondary IDE cable, labeled J3, from the front panel board. See letter “B” in
Figure 3.
4. Disconnect the primary IDE cable, labeled J5, from the front panel board. See letter “C” in
Figure 3.
C
B
A
Figure 24. Disconnecting Front Panel Cables
TP01820
®
Intel
Storage System SSR316MJ2 Cable Kit 33
Front Panel Cables Installation Procedures
Disconnect Front Panel Cables from Server Board
1. Disconnect the primary IDE cable, labeled J1J1, from the server board. See letter “A” in
Figure 3.
2. Disconnect the secondary IDE cable, labeled J1J4, from the server board. See letter “B” in
Figure 3.
3. Disconnect the front panel cable, labeled J1J2, from the server board. See letter “C” in
Figure 3.
C
B
A
®
Intel
Storage System SSR316MJ2 Cable Kit 34
TP01817
Figure 25. Disconnecting Front Panel Cables
Front Panel Cables Installation Procedures
Connect New Front Panel Cables to Server Board
1. Open the Front Panel Cables package that is part of the FMJCABLES2 Cable Kit. Route the
front panel cables along the side of the chassis in the same way the original cables were routed.
2. Connect the primary IDE cable, labeled J2J2, to the server board. The primary IDE cable has a
blue metal sheath and the connector on the front panel is also blue. See letter “A” in
3. Connect the secondary IDE cable, labeled J1J4, to the server board. See letter “B” in
The secondary IDE cable has a white metal sheath and the connector on the front panel is also
white.
4. Connect the front panel cable, labeled J1J2, to the server board. See letter “C” in
C
B
A
Figure 20.
Figure 20.
Figure 20.
Figure 26. Connecting Front Panel Cables to Server Board
®
Intel
Storage System SSR316MJ2 Cable Kit 35
TP01818
Front Panel Cables Installation Procedures
Connect Front Panel Board Cables to Front Panel
Board
1. Connect the front panel cable, labeled J1, to the front panel board. See letter “A” in Figure 20.
2. Connect the secondary IDE cable, labeled J3, to the front panel board. See letter “B” in
Figure 20. The secondary IDE cable has a white metal sheath and the connector on the front
panel is also white.
3. Connect the primary IDE cable, labeled J5, to the front panel board. The primary IDE cable has
a blue metal sheath and the connector on the front panel is also blue. See letter “C” in
Figure 20.
C
B
A
Figure 27. Connecting Front Panel Board Cables
TP01819
®
Intel
Storage System SSR316MJ2 Cable Kit 36
Front Panel Cables Installation Procedures
Finishing Up
1. Facing the front of the system, set the chassis cover into the corresponding slot in the chassis.
2. Pull the top cover forward. See letter “A” in
3. Tighten the two thumb screws at the rear of the chassis. See letter “B” in
4. Connect the AC power cables. See letter “C” in
5. Power on your Intel® Storage System Console. See letter “D” in
Figure 22.
Figure 22.
Figure 22.
Figure 22.
B
C
A
B
D
TP01816
Figure 28. Installing the Chassis Cover
®
Intel
Storage System SSR316MJ2 Cable Kit 37
I2C Cables Installation Procedures
I2C Cables Installation Procedures
Required Tools
Cross-head (Number 1 Size Phillips
Wire cutters
Power Down System and Remove Chassis Cover
1. Review the safety information and warnings at the beginning of this guide.
2. Power down your Intel® Storage System Console. See letter “A” in
3. Remove both AC power cords from the AC power inputs at the rear of your storage system.
See letter “B” in
4. Loosen the two thumb screws at the rear of the chassis cover. See letter “C” in
5. Facing the front of the chassis, push the top cover rearward, and then lift it up to remove it.
See letter “D” in
Figure 1.
Figure 1.
*
) screwdriver
Figure 1.
Figure 1.
B
C
D
C
A
®
Intel
Storage System SSR316MJ2 Cable Kit 38
Figure 29. Removing Chassis Cover
TP01797
I2C Cables Installation Procedures
Disconnect Front Panel Cables
1. Disconnect the front panel cable, labeled J1, from the front panel board. See letter “A” in
Figure 3.
2. Disconnect the secondary IDE cable, labeled J3, from the front panel board. See letter “B” in
Figure 3.
3. Disconnect the primary IDE cable, labeled J5, from the front panel board. See letter “C” in
Figure 3.
4. Disconnect the front panel power connector from the front panel board. See letter “D” in
Figure 3.
A
B
C
Figure 30. Disconnecting Front Panel Cables
D
TP01799
®
Intel
Storage System SSR316MJ2 Cable Kit 39
I2C Cables Installation Procedures
Remove Fan Assembly Screws
Use a Number 1 size Phillips* screwdriver to remove the screw on each side of the system. See
letter “A” in
screws will be re-installed later.
Figure 4. These screws hold the system fan assembly in place. See Figure 4. These
A
Figure 31. Removing System Fan Assembly Screws
TP01800
®
Intel
Storage System SSR316MJ2 Cable Kit 40
I2C Cables Installation Procedures
Disconnect Fan Cables
1. Disconnect the Fan 3 cable from the server board. See letter “A” in Figure 5.
2. Disconnect the Fan 4 cable from the server board. See letter “B” in
3. Disconnect the Fan 5 cable from the server board. See letter “C” in
B
A
C
A
Figure 5.
Figure 5.
B
C
Figure 32. Disconnecting System Fan Cables
TP01801
®
Intel
Storage System SSR316MJ2 Cable Kit 41
I2C Cables Installation Procedures
Remove Fan Assembly
Simultaneously pull up on both sides of the system fan assembly to remove the fan assembly from
the storage system. See letter “A” in
Figure 6. Set the system fan assembly on a static-free surface.
A
A
Figure 33. Removing System Fan Assembly
TP01821
®
Intel
Storage System SSR316MJ2 Cable Kit 42
I2C Cables Installation Procedures
Disconnect I2C Cables
NOTE
The I2C cables are labeled at each end, on the cable connector. In the
instructions and the figure below, it is assumed that letter “A” corresponds to
your cable labeled JP4 and SL3_J13. Your connections may be different. It is
important that you write down the connections as they exist in your chassis,
so you may later correctly reconnect them.
1. Write down the I2C cable connector positions on the backplane board and on the SATA Host
Bus Adapter cards. You will later need to re-connect these cables to the same headers.
2. Disconnect the I2C cable that is labeled JP4 from the backplane board at the front of the
chassis. See letter “A” in the circled area of
3. Disconnect the I2C cable that is labeled SL3_J13from the SATA Host Bus Adapter card set.
See letter “A” in
Figure 7.
4. Disconnect the I2C cable that is labeled JP6 from the backplane board. See letter “B” in the
circled area of
Figure 7.
5. Disconnect the I2C cable that is labeled SL2_J13from the SATA Host Bus Adapter card set.
See letter “B” in Figure 8.
Figure 7.
A
B
B
A
Figure 34. Disconnecting I2C Cables
TP01804
®
Intel
Storage System SSR316MJ2 Cable Kit 43
I2C Cables Installation Procedures
Connect I2C Cables
NOTE
The I2C cables are labeled at each end, on the cable connector. In the
instructions and the figure below, it is assumed that letter “A” corresponds to
your cable labeled JP4 and SL3_J13. Your connections may be different.
Refer to the notes you made when you disconnected the cables to ensure you
are reconnecting them in the correct places.
1. Connect the I2C cable that is labeled JP4 to the backplane board. See letter “A” in the circled
area of
2. Connect the I2C cable that is labeled SL3_J13to the SATA Host Bus Adapter card set. See
letter “A” in Figure 14.
3. Connect the I2C cable that is labeled JP6 to the backplane board. See letter “B” in the circled
area of
4. Connect the I2C cable that is labeled SL2_J13to the SATA Host Bus Adapter card set. See
letter “B” in Figure 14.
Figure 13.
Figure 13.
A
B
B
A
Figure 35. Connecting I2C Cables
TP01822
®
Intel
Storage System SSR316MJ2 Cable Kit 44
I2C Cables Installation Procedures
Install Fan Assembly
1. Move loose wires away from the space where the system fan assembly will be installed.
2. Align the holes on the bottom edge of the system fan assembly with the blue plastic brackets on
the bottom of the chassis.
3. Set the system fan assembly into place. See letter “A” in
A
Figure 17.
A
Figure 36. Installing System Fan Assembly
TP01811
®
Intel
Storage System SSR316MJ2 Cable Kit 45
I2C Cables Installation Procedures
Attach Fan Assembly
Use a Number 1 size Phillips screwdriver to attach the fan assembly to the chassis, using one screw
at each side of the system. See letter “A” in
Figure 18.
A
Figure 37. Attaching System Fan Assembly
TP01812
®
Intel
Storage System SSR316MJ2 Cable Kit 46
I2C Cables Installation Procedures
Connect System Fan Cables
1. Connect the Fan 3 cable to the server board. See letter “A” in Figure 19.
2. Connect the Fan 4 cable to the server board. See letter “B” in
3. Connect the Fan 5 cable to the server board. See letter “C” in
B
A
C
A
Figure 19.
Figure 19.
B
C
Figure 38. Connecting System Fan Cables
TP01813
®
Intel
Storage System SSR316MJ2 Cable Kit 47
I2C Cables Installation Procedures
Connect Front Panel Board Cables
1. Connect the front panel cable, labeled J1, to the front panel board. See letter “A” in Figure 20.
2. Connect the secondary IDE cable, labeled J3, to the front panel board. See letter “B” in
Figure 20. The secondary IDE cable has a white metal sheath and the connector on the front
panel is also white.
3. Connect the primary IDE cable, labeled J5, to the front panel board. The primary IDE cable has
a blue metal sheath and the connector on the front panel is also blue. See letter “C” in
Figure 20.
4. Connect the front panel power connector to the front panel board. See letter “D” in
Figure 20.
C
B
A
Figure 39. Connecting Front Panel Board Cables
D
TP01814
®
Intel
Storage System SSR316MJ2 Cable Kit 48
I2C Cables Installation Procedures
Finishing Up
1. Facing the front of the system, set the chassis cover into the corresponding slot in the chassis.
2. Pull the top cover forward. See letter “A” in
3. Tighten the two thumb screws at the rear of the chassis. See letter “B” in
4. Connect the AC power cables. See letter “C” in
5. Power on your Intel® Storage System Console. See letter “D” in
Figure 22.
Figure 22.
Figure 22.
Figure 22.
B
C
A
B
D
TP01816
Figure 40. Installing the Chassis Cover
®
Intel
Storage System SSR316MJ2 Cable Kit 49
Loading...