Insignia NS-HWMC1848 User Manual

Download

USER GUIDE

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

NS-HWMC1848

SAFETY INFORMATION AND SPECIFICATIONS .2

PACKAGE CONTENTS: PARTS ..................................4

PACKAGE CONTENTS: HARDWARE .......................5

ASSEMBLY INSTRUCTIONS ......................................7

CARE AND MAINTENANCE ................................... 33

Before using your new product, please read these instructions to prevent any damage.

NS-HWMC1848

32 inch (81.3 cm)

8.75 inch (22.2 cm)

55.25 inch (140.3 cm)

7.2 inch (18.3 cm)

7.7 inch (19.5 cm)

22 inch (55.8 cm)

47.75 inch (121.2 cm)

15.8 inch (40.2 cm)

15 inch (38 cm)

18.4 inch (46.8 cm)

43.8 inch (111.2 cm)

39.75 inch (101 cm)

22.5 inch (57.2 cm)

47.75 inch (121.2 cm)

20 inch (50.8 cm)

33.25 inch (84.45 cm)

SAFETY INFORMATION AND SPECIFICATIONS

CAUTION: The top surface of this stand

is designed for use with a product weighing no more than 135 lbs. (61.2 kg) and having a width

that permits it to sit evenly on the stand with no more than a one-inch overhang on each side of the shelf. Use with products that weigh more than the maximum weight allowed, or with dimensions that extend beyond the maximum width may result in instability, which may result in injury.

CAUTION: This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children!

Maximum overall weight: 235 lbs (106.6 kg) Maximum top shelf weight: 135 lbs (61.2 kg) Maximum lower shelf weight: 50 lbs (22.6 kg) Maximum TV weight on swivel stand: 135 lbs

(61.2 kg) Recommended screen range: 37" - 55” diag.

(32.5 - 49.75” width)

Overall dimensions (H × W × D):

55.25 × 47.75 × 22.5 in. (140.3 x 121.2 x 57.2 cm)

TV stand weight: 81.6 lbs (37 kg)

Vesa Compatibility: 100 x 100 mm, 200 x 100 mm,

200 x 200 mm, 200 x 300 mm, 200 x 400 mm, 300 x 300 mm, 400 x 300 mm, 400 x 400 mm, 600 x 400 mm

www.insigniaproducts.com

Tools needed:

Phillips screwdriver

Level

Power drill

Hammer

Edge-to-edge stud finder

Pencil

3/8” drill bit (for tipping restraint)

3/16” wood drill bit or 7/16” masonry drill bit

1/2” Socket wrench

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

www.insigniaproducts.com

PACKAGE CONTENTS: PARTS

A Left side frame (1)

B Right side frame (1)

D Bottom crossbar (1)

E Bottom left rail (1)

C Long rear support (1)

F Bottom right rail (1)

G Back stretcher (2)

H Support leg (2)

I Top she lf (1)

J Middle shelf (1)

K Bottom shelf (1)

L Back panel (1)

N Mounting frame (1)

M Swivel bracket (1)

P TV brackets L/R (2)

Make sure that you have all the parts necessary to assemble your new TV stand.

NS-HWMC1848

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

Label Hardware Qty.

T14

U16

V12

W46

Cable clip

Screw #4 x 10 mm

Bolt 1/2” (12.7 mm)

Bolt 5/8” (15.87 mm)

Bolt 1 5/8” (41,27 mm)

Bolt 2 1/4” (57.15 mm)

Lock washer

Label Hardware Qty.

X46

AA 4

BB 4

CC 4

DD 1

EE 2

FF 1

Flat washer

Hex nut

Hex wrench 3/16” (4.76 mm)

Lag bolt

Large flat washer

Concrete anchor

Open wrench

Hex wrench 0.158” (4 mm)

Touc h-up pen

PACKAGE CONTENTS: HARDWARE

Note: You may receive extra hardware.

Make sure that you have all the hardware necessary to assemble your new TV stand.

www.insigniaproducts.com

PACKAGE CONTENTS: HARDWARE (continued)

Label Hardware Qty.

GG 1

HH 4

II 4

JJ 4

KK 4

LL 4

MM 4

NN 4

PP 4

QQ 4

Tipping restraint hardware kit

Bolt M4 × 12 mm

Bolt M4 × 30 mm

Bolt M5 × 12 mm

Bolt M5 × 30 mm

Bolt M6 × 12 mm

Bolt M6 × 35 mm

Bolt M8 × 16 mm

Bolt M8 × 20 mm

Bolt M8 × 40 mm

Label Hardware Qty.

RR 4

SS 4

TT 4

UU 4

VV 4

WW 4

XX 4

YY 8

ZZ 4

Bolt M8 × 50 mm

Lock washer M4

Lock washer M5

Lock washer M6

Lock washer M8

Large spacer

Small spacer

Flat washer M4/M5

Flat washer M6/M8

NS-HWMC1848

10 20 30 40 50 60 70 80 90 100mm

1234in

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

U (8)

W (8)

X (8)

EE (1)

ASSEMBLY INSTRUCTIONS

Step 1: Attach the back stretchers between the side frames

Tip: Assemble your stand on a carpeted floor or the empty TV stand carton to avoid scratching it.

1 Insert four 1 5/8" bolts (U), with lock washers (W) and flat washers (X), through the drilled holes on the left side

frame (A) and screw them into the threaded holes on the side of the back stretchers (G) with the 4 mm hex key (EE). Make sure that the metal brackets on the back stretchers (G) are located on the front side and faced inward.

2 Repeat the same procedure to attach the right side frame (B).

NOTE: Do not fully tighten all bolts until you finish assembling all of the parts. After assembly, go back and fully

tighten all bolts. This will make the assembly easier.

You’ll need:

www.insigniaproducts.com

NS-HWMC1848

Pilot hole

R (4)

Phillips screwdriver

Step 2: Attach the back panel between the back stretchers

• Using the pilot holes as guide, insert four 10 mm screws (R) through the metal brackets of the back stretchers (G)

and securely screw them into the back panel (L) using a Phillips screwdriver.

You’ll need:

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

U (4)

W (4)

X (4)

EE (1)

Step 3: Align and attach the top shelf to the side frames

• Insert four 1 5/8” bolts (U), with lock washers (W) and flat washers (X), through the drilled holes on the top rails of

both side frames (A and B), then securely screw them into the threaded holes on the top shelf (I) using the 4 mm hex key (EE).

You’ll need:

www.insigniaproducts.com

NS-HWMC1848

U (4)

W (4)

X (4)

EE (1)

Step 4: Align and attach the middle shelf to the side frames

• Insert four 1 5/8” bolts (U), with lock washers (W) and flat washers (X), through the drilled holes on the middle

rails of both side frames (A and B), then securely screw them into the threaded holes on the middle shelf (J) using the 4 mm hex key (EE).

You’ll need:

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

T (4)

W (4)

X (4)

EE (1)

Step 5: Attach the bottom subframe

• Insert four 5/8” bolts (T), with lock washers (W) and flat washers (X), through the end brackets on the left and

right rails (E and F), then securely screw them into the threaded holes on the bottom crossbar (D) with the 4 mm hex key (EE). Make sure that the metal tabs face inward and are flush with each other.

You’ll need:

www.insigniaproducts.com

Step 6: Attach the bottom subframe to the bottom shelf

T (6)

W (6)

X (6)

EE (1)

1 Insert six 5/8” bolts (T), with lock washers (W) and flat washers (X), through the metal tabs on the bottom

crossbar (D) and the side rails (E and F), then finger tighten them into the threaded holes on the bottom shelf (K).

2 Tighten the bolts (T) with the 4 mm hex key (EE).

NS-HWMC1848

You’ll need:

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

V (4)

W (4)

X (4)

EE (1)

Step 7: Align and attach the bottom shelf to the side frames

• Insert four 2 1/4” bolts (V), with lock washers (W) and flat washers (X), through the drilled holes on the bottom

rails of both side frames (A and B), then securely screw them into the threaded holes on the bottom shelf (K) with the 4 mm hex key (EE).

You’ll need:

www.insigniaproducts.com

Step 8: Attach the support legs to the bottom shelf

1 Securely screw two support legs (H) into the threaded holes on the back rail of the bottom shelf (K). 2 Stand the assembled frame upright.

NOTE: For swivel stand assembly, see “SWIVEL STAND ASSEMBLY INSTRUCTIONS

Table Top assembly, continue to the next step.

” on page 26. For Wall Mount or

NS-HWMC1848

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

Q (2)

T (4) EE (1)

Step 9: Attach the cable clips

• Attach two of the cable clips (Q) to the back of the side frames (A and B) with two 5/8" bolts (T) per cable clip

using the 4 mm hex key (EE).

You’ll need:

www.insigniaproducts.com

NS-HWMC1848

Anchor

Wall

Bolt

Long screw

Leveling feet

GG (1)

Power drill

3/8” masonry or wood drill bit

Level

FINAL TABLE TOP ASSEMBLY INSTRUCTIONS

Step 10: Position the TV stand and install the tipping restraint hardware kit

1 Position the assembled stand against a wall where you plan to use it. 2 Adjust the leveling feet to level the TV stand. 3 Follow the instructions printed on the bag containing the tipping restraint hardware kit (GG) to attach the

restraint hardware to the wall and the stand.

WAR NI NG: It is very important that the tipping restraint be installed correctly. Failure to do this could result in your

TV/stand assembly falling forward, resulting in damage to equipment or personal injury.

You’ll need:

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

WALL MOUNT ASSEMBLY INSTRUCTIONS

Step 1: Select the correct bolts, washers, and spacers for your TV.

If you are in doubt about which size bolt to use, try one of the bolts in one of the four Vesa mounting holes on the back of your TV. A bolt that is too large will be obvious and not fit in the hole at all, but make sure that the bolt size you choose is not too loose. It should grip the hole threads evenly and not wobble. After you determine which size bolts to use, go on to the next step.

M4 hardware assembly:

•M4 x 12 mm bolts (HH) top screw holes

•M4 x 30 mm bolts (II) bottom screw holes

•M4 lock washers (SS)

•M4/M5 Flat washers (YY)

•Small spacers (XX)

M5 hardware assembly:

•M5 x 12 mm bolts (JJ) top screw holes

•M5 x 30 mm bolts (KK) bottom screw holes

•M5 lock washers (TT)

•M4/M5 flat washers (YY)

•Small spacers (XX)

M6 hardware assembly:

•M6 x 12 mm bolts (LL) top screw holes

•M6 x 35 mm bolts (MM) bottom screw holes

•M6 lock washers (UU)

•M6/M8 flat washers (ZZ)

•Large spacers (WW)

M8 hardware assembly:

•M8 x 16 mm bolts (NN) or M8 x 20 mm bolts (PP) top screw holes

•M8 x 40 bolts (QQ) or M8 x 50 bolts (RR) bottom screw holes

•M8 lock washers (VV)

•M6/M8 flat washers (ZZ)

•Large spacers (WW)

www.insigniaproducts.com

NS-HWMC1848

Step 2: Determine whether your TV has a flat back or an irregular or obstructed back or a curved screen

1 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages

and scratches.

2 If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV for

instructions.

3 Temporarily lay the TV brackets (P) vertically on the back of your TV. 4 Align the screw holes in the TV brackets with the mounting screw holes on your TV. 5 Identify which type of back your TV may have:

• Flat back: The brackets lay flush against the back of your TV and do not block any jacks. You do not need spacers

when assembling the wall mount.

• Obstructed back: The brackets block any of the jacks on the back of your TV. You will need spacers when

assembling the wall mount.

• Irregularly-shaped back or curved screen TVs: There is a gap between the bracket and some part of the back of

your TV. You will need spacers when assembling the wall mount.

6 Remove the brackets.

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

JJ LL NN PP

UU VVTT

JJ LL NN PPHH

JJ LL NN

UU VV

PPHH

Installing the mounting brackets for the 100 x 100 mm vesa hole pattern

HH (4)

Bolts & Washers

JJ (4)

LL (4)

NN (4)

SS (4)

TT (4)

UU (4)

VV (4)

YY (4)

ZZ (4)

Phillips screwdriver

Level

P TV brackets (2)

PP (4)

Step 3: Option 1 - Mounting bracket instructions for a TV with a flat back

To mount the TV brackets:

1 Insert the selected bolts through the washers and proper mounting holes on the TV brackets (P) (for the 100 x

100 mm vesa pattern you’ll need to lift the bracket hangers to insert the screws), then finger tighten them into the threaded holes on the back of your TV. Make sure the TV brackets are centered and level with each other and the hooks face the bottom of the TV.

NOTE: Lean the TV up against a wall or other solid surface when attaching with the TV brackets. DO NOT place the TV

face down on the glass, this may cause permanent damage.

2 Tighten the bolts until they are snug against the TV bracket using a Phillips screwdriver. DO NOT over tighten.

You’ll need:

www.insigniaproducts.com

NS-HWMC1848

Installing the mounting brackets for the 100 x 100 mm vesa hole pattern

II (4)

Bolts & Washers

KK (4)

MM (4)

QQ (4)

SS (4)

TT (4)

UU (4)

VV (4)

YY (4)

ZZ (4)

Phillips screwdriver

Level

P TV brackets L/R (2)

XX (4)

WW (4)

RR (4)

Step 3: Option 2 - Mounting bracket instructions for a TV with an irregularly shaped or obstructed back or curved screen TVs.

1 Insert the selected bolts through the washers and proper mounting holes on the TV brackets (P) (for the 100 x

NOTE: Lean the TV up against a wall or other solid surface when attaching with the TV brackets. DO NOT place the TV

face down on the glass, this may cause permanent damage.

2 Tighten the bolts until they are snug against the TV bracket using a Phillips screwdriver. DO NOT over tighten.

KK MM QQ RR

You’ll need:

JJ LL NN PP

SSWWUU VV

UU VVTT

JJ LL NN PP

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

2.50” (64 mm)

0.19”

(4.76 mm)

AA (4)

BB (4)

Level

Edge-to-edge stud finder

Pencil

3/16” drill bit

Drill

1/2” Socket wrench

Step 4: Option 1 - Mount the frame to a stud wall

NOTE: See Step 4: Option 2 for instructions on mounting the frame to a concrete wall.

1 Use a stud sensor to locate two adjacent wall studs, then position the mounting frame (N) exactly between the

two studs.

2 Use a level to make sure that the mounting frame is level, then mark the four mounting holes. Remove the

mounting frame.

3 Drill four 3/16" (4.76 mm) holes 2.5" (64 mm) deep. 4 Align the mounting frame (N) with the pilot holes, then secure it to the wall with four lag bolts (AA) and four

washers (BB).

CAUTION: Make sure that the lag bolts are tight and secure, but do not overtighten them.

You’ll need:

www.insigniaproducts.com

Step 4: Option 2 - Mount the frame to a block or concrete wall

2.50” (64 mm)

0.43”

(11 mm)

AA (4)

BB (4)

CC (4)

Hammer

Level

7/16” masonry drill bit

Drill

Pencil

1/2” Socket wrench

1 Place the mounting frame (N) against the wall where you intend to mount the TV. Use a level to make sure the

mounting frame (N) is level, then mark the four mounting holes on the wall. Never locate the mounting holes into the mortar between blocks. Remove the mounting frame.

2 Drill four 7/16" (11 mm) holes through the screw marks to a depth of 2.5" (64 mm). 3 Insert a concrete anchor (CC) into each of the screw holes using a hammer. 4 Align the mounting frame over the concrete anchors. 5 Place a washer (BB) over one of the mounting frame screw holes, then insert a lag bolt (AA) and tighten. 6 Repeat the previous step for the other three screw holes.

CAUTION: Make sure that the lag bolts are tight and secure, but do not overtighten them.

NS-HWMC1848

You’ll need:

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

Tighten until the safety bolt hits the underside of the mounting frame.

Note: In this step the mounting frame has already been mounted to the wall. This illustration shows the TV from the back view for clarity.

Phillips screwdriver

Step 5: Attaching the TV to the mounting frame on the wall

1 Lift the TV up to the mounting frame (N). 2 Set the hooks on TV brackets (P) over the mounting frame, then lower the hooks onto the bars on the mounting

frame.

3 Center the TV, then secure it in place using a screwdriver to tighten the safety bolt on the bottom hooks. 4 Place the stand with the glass shelves under the TV.

You’ll need:

www.insigniaproducts.com

NS-HWMC1848

-5° ~ 11°

Turn clockwise to tighten Turn counterclockwise to loosen

(Z)

Step 6: Adjusting the tilt

The TV brackets (P) allow you to make a tilt adjustment of up to 11° down and 5° up to provide optimum viewing and minimize glare.

1 Loosen the tension knobs on both TV brackets (P), then grasp the edge of the TV and move it up or down to the

position you want.

2 Turn the tension knob clockwise to secure the brackets in position. Use the the 4.76 mm hex wrench (Z) to

tighten the tension knobs, if necessary.

You’ll need:

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

Anchor

Wall

Bolt

Long screw

Leveling feet

GG (1)

Power drill

3/8” masonry or wood drill bit

Level

Step 7: Position the TV stand and install the tipping restraint hardware kit

1 Position the assembled stand against a wall where you plan to use it. 2 If necessary, adjust the leveling feet to level the TV stand. 3 Follow the instructions printed on the bag containing the tipping restraint hardware kit (GG) to attach the

restraint hardware to the wall and the stand.

WAR NIN G: It is very important that the tipping restraint be installed correctly. Failure to do this could result in your

TV/stand assembly falling forward, resulting in damage to equipment or personal injury.

You’ll need:

www.insigniaproducts.com

NS-HWMC1848

Sockets for cable clips face backward.

V (4)

W (4)

X (4)

EE (1)

SWIVEL STAND ASSEMBLY INSTRUCTIONS

Step 1: Align and attach the long rear support

• Insert four 2¼" bolts (V), with lock washers (W) and the flat washers (X), through the drilled holes in the long rear

support (C), then securely screw them into the threaded holes of the side frames (A and B) with the 4 mm hex key (EE).

NOTE: Make sure that the sockets for the cable clips face backward.

You’ll need:

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

V (4)

W (8)

X (8)

Y (4)

DD (1)

EE (1)

Step 2: Attach the swivel bracket

1 Align the swivel bracket (M) at the height you would like the center of your TV to be. 2 Insert a 2¼” bolt (V), with a lock washer (W) and a flat washer (X), through the swiveling bracket (N) and the

long rear support (C).

3 Place a second flat washer (X) and a lock washer (W) onto the end of the threaded bolt, then finger tighten a hex

nut (Y) onto the bolt. 4 Repeat this procedure for the three remaining holes. 5 Securely tighten with the open end wrench (DD) and 4 mm hex key (EE).

NOTE: The swivel bracket allows your TV to swivel from side to side, but will not allow your TV to tilt up or down.

You’ll need:

www.insigniaproducts.com

NS-HWMC1848

S (4)

W (4)

X (4)

EE (1)

Step 3: Attach the mounting frame to the swivel bracket

1 Hold the flat side of the mounting frame (N) against the swivel bracket (M), aligning the holes. Make sure that

the two recessed holes on mounting frame (N) are at the bottom. 2 Insert a 1/2" bolt (S), with a lock washer (W) and a flat washer (X), through the hole in the swivel bracket (M),

then screw it into the threaded hole on the mounting frame (N). 3 Repeat this for the three remaining holes joining the swiveling bracket (M) to the mounting frame (N). 4 Securely tighten with the 4 mm hex key (EE).

You’ll need:

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

Q (2)

T (4)

EE (1)

Step 4: Attach the cable clips

• Attach the cable clips (Q) to the back of the long rear support (C) in two of four possible locations with two 5/8" bolts (T) per cable clip.

You’ll need:

www.insigniaproducts.com

NS-HWMC1848

Phillips screwdriver

Step 5: Attaching the TV to the mounting frame on the swivel bracket

1 Attach the TV brackets (P) to the back of the television following the steps on pages 18, 19, and 20, depending

on the type of TV that you own.

2 Lift the TV up to the mounting frame (N). 3 Set the hooks on TV brackets (P) over the mounting frame (N), then lower the hooks onto the bars of the

mounting frame.

4 Center the TV, then secure it in place using a screwdriver to tighten the safety bolt on the bottom hooks. Tighten

until the safety bolt hits the underside of the mounting frame.

You’ll need:

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

-5° ~ 11°

Turn clockwise to tighten Turn counterclockwise to loosen

(Z)

Step 6: Adjusting the tilt

The TV brackets (P) allow you to make a tilt adjustment of up to 11° down and 5° up to provide optimum viewing and minimize glare.

1 Loosen the tension knobs on both TV brackets (P), then grasp the edge of the TV and move it up or down to the

position you want.

2 Turn the tension knob clockwise to secure the brackets in position. Use the the 4.76 mm hex wrench (Z) to

tighten the tension knobs, if necessary.

You’ll need:

www.insigniaproducts.com

NS-HWMC1848

Anchor

Wall

Nut and washers

Long screw

Leveling feet

GG (1)

Power drill

3/8” masonry or wood drill bit

Level

Step 7: Position the TV stand and install the tipping restraint hardware kit

restraint hardware to the wall and the stand.

WAR NI NG: It is very important that the tipping restraint be installed correctly. Failure to do this could result in your

TV/stand assembly falling forward, resulting in damage to equipment or personal injury.

You’ll need:

www.insigniaproducts.com

Wood Finish 3-in-1 TV Stand for TVs up to 55”/135 lbs.

CARE AND MAINTENANCE

Wood/Laminate

• Use your favorite type of furniture polish.

• Do not spray polish directly onto the stand. Spray onto a soft cloth then wipe the stand.

• Always test any polish in a discrete location first, such as the back of the stand, to make sure that there is no adverse reaction.

• Dust frequently with a soft cloth.

• Never slide objects across surfaces. Lift objects from the top surface rather than dragging them across the finish when moving them.

• Do not expose your stand to direct sunlight, drying heat sources, or dampness.

Glass

• Use a commercial liquid glass cleaner and a soft cloth.

• Do not use harsh powders or any other abrasive substances as they will scratch the glass.

• Clean spills immediately with a soft, damp cloth.

• Protect surfaces by using felt, leather, or cork under accessories.

• Use a protective pad when using your stand as a writing surface (especially when using a ballpoint pen).

• Dust frequently with a soft cloth.

WARNING

Please use your stand correctly and safely. Improper use can cause safety hazards or damage to your furniture or household items. Carefully read the following chart.

Look out for: What can happen: How to avoid the problem:

• Children climbing on the stand.

• A child may try to reach a toy or other object by climbing on the stand.

• Children will play and be active near the TV.

• Improper use of the stand to support TVs.

• The stand is designed for use with TVs will specify the maximum weight rating and recommended size of the TVs it will safely support.

• Overloaded shelves. • Risk of injury.

• Improperly moving the stand. • The stand can tip over or break if improperly moved.

• The TV/stand assembly tipping forward. • Risk of injury.

• Risk of injury or death.

• A child climbing on the stand can make it top-heavy and cause it to tip over.

• A child playing with a TV can cause it to tip over.

• Risk of injury or death.

• TVs can be ver y heavy. Note, older CRT TVs tend to be unbalanced and prone to tipping forward.

• Top-heavy furniture can tip over.

• Overloaded shelves can break.

• Risk of injury.

• Top-heavy furniture can tip over.

• The TV and stand could be damaged.

• Never allow children to climb on or play with the stand.

• Do not place toys or food on the top shelves. Children may try to climb to reach them out of curiosity.

• A TV must only be set on furniture specifically designed to support a television.

• Never use a TV that exceeds the weight ratings or size guidelines specified for the stand.

• Never exceed the weight limits shown in the instructions.

• Work from the bottom to the top when loading shelves.

• The bottom shelves can only support 50 lbs. while the top can support 135 lbs.

• Unload shelves from the top to the bottom before moving the stand.

• Do not push the stand, especially on a carpeted floor. Have a friend help you lift the item and set it in place.

• Do not lift the stand using the top shelf. Lift from the frame or leg assembly.

• Remove the TV before moving the TV stand.

• Use the tipping restraint hardware provided and install it properly.

www.insigniaproducts.com

NS-HWMC1848

ONE-YEAR LIMITED WARRANTY

Definitions:

The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).

For this warranty to apply, your Product must be purchased in the United States or Canada from a Best Buy branded retail store or online at

www.bestbuy.com or www.bestbuy.ca and is packaged with this warranty statement.

How long does the coverage last?

The Warranty Period lasts for 1 year (365 days) from the date you purchased the Product. Your purchase date is printed on the receipt you received with the Product.

What does this warranty cover?

During the Warranty Period, if the original manufacture of the material or workmanship of the Product is determined to be defective by an authorized Insignia repair center or store personnel, Insignia will (at its sole option): (1) repair the Product with new or rebuilt parts; or (2) replace the Product at no charge with new or rebuilt comparable products or parts. Products and parts replaced under this warranty become the property of Insignia and are not returned to you. If service of Products or parts are required after the Warranty Period expires, you must pay all labor and parts charges. This warranty lasts as long as you own your Insignia Product during the Warranty Period. Warranty coverage terminates if you sell or otherwise transfer the Product.

How to obtain warranty service?

If you purchased the Product at a Best Buy retail store location or from a Best Buy online website (www.bestbuy.com or www.bestbuy.ca), please take your original receipt and the Product to any Best Buy store. Make sure that you place the Product in its original packaging or packaging that provides the same amount of protection as the original packaging.

To obtain warranty service, in the United States and Canada call 1-877-467-4289. Call agents may diagnose and correct the issue over the phone.

Where is the warranty valid?

This warranty is valid only in the United States and Canada at Best Buy branded retail stores or websites to the original purchaser of the product in the county where the original purchase was made.

What does the warranty not cover?

This warranty does not cover:

• Customer instruction/education

• Installation

•Set up adjustments

• Cosmetic damage

• Damage due to weather, lightning, and other acts of God, such as power surges

•Accidental damage

•Misuse

•Abuse

• Negligence

• Commercial purposes/use, including but not limited to use in a place of business or in communal areas of a multiple dwelling condominium or apartment complex, or otherwise used in a place of other than a private home.

• Modification of any part of the Product, including the antenna

• Display panel damaged by static (non-moving) images applied for lengthy periods (burn-in).

• Damage due to incorrect operation or maintenance

• Connection to an incorrect voltage or power supply

• Attempted repair by any person not authorized by Insignia to service the Product

• Products sold “as is” or “with all faults”

• Consumables, including but not limited to batteries (i.e. AA, AAA, C etc.)

• Products where the factory applied serial number has been altered or removed

• Loss or Theft of this product or any part of the product

• Display panels containing up to three (3) pixel failures (dots that are dark or incorrectly illuminated) grouped in an area smaller than one tenth (1/10) of the display size or up to five (5) pixel failures throughout the display. (Pixel based displays may contain a limited number of pixels that may not function normally.)

• Failures or Damage caused by any contact including but not limited to liquids, gels or pastes.

REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY FOR BREACH OF WARRANTY. INSIGNIA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS OR LOST PROFITS. INSIGNIA PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THE WARRANTY PERIOD. SOME STATES, PROVINCES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.

Contact Insignia: 1-877-467-4289 www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies. *Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2019 Best Buy. All rights reserved.

www.insigniaproducts.com

1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)

www.insigniaproducts.com

INSIGNIA is a trademark of Best Buy and its affiliated companies. Registered in some countries. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2019 Best Buy. All rights reserved.

Mount WH60TM meets public safety requirements as designated by the Underwriters Laboratories in both US & Canada

U.S. Patents 8,079,311 & 8,191,485 U.S. Patent 9,215,927

V5 ENGLISH 19-0691

Insignia NS-HWMC1848 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

SAFETY INFORMATION AND SPECIFICATIONS

PACKAGE CONTENTS: PARTS

PACKAGE CONTENTS: HARDWARE

ASSEMBLY INSTRUCTIONS

FINAL TABLE TOP ASSEMBLY INSTRUCTIONS

WALL MOUNT ASSEMBLY INSTRUCTIONS

SWIVEL STAND ASSEMBLY INSTRUCTIONS

CARE AND MAINTENANCE

Wood/Laminate

Glass

ONE-YEAR LIMITED WARRANTY

Definitions:

How long does the coverage last?

What does this warranty cover?

How to obtain warranty service?

Where is the warranty valid?

What does the warranty not cover?