Insignia NS-HTVMF0C Installation Manual
INSTALLATION GUIDE
Fixed-Position Wall Mount
for TVs 40–70 in.
NS-HTVMF0C
Before using your new product, please read these instructions to prevent any damage.
Safety information and specifications
Maximum TV weight: 100 lbs. (45.3 kg)
Screen size: 40 in. to 70 in. diagonal
Overall dimensions (H × W ):
17.0 × 25.6 in. (43.2 × 65 cm)
Wall-mount weight: 2.4 lb (1.1 kg)
We’re here for you
www.insigniaproducts.com
For customer service, call:
877-467-4289 (U.S./Canada markets)
17.0 in. (43.2 cm)
2.97 in. (7.5 cm)
25.6 in. (65 cm)
CAUTION: IMPORTANT SAFETY
INSTRUCTIONS - SAVE THESE
INSTRUCTIONS - READ THE
ENTIRE MANUAL PRIOR TO USE
CAUTION: Do not use this product for any
purpose not explicitly specified by Insignia.
Improper installation may cause property
damage or personal injury. If you do not
understand these directions, or have doubts
about the safety of the installation, contact
Customer Service or call a qualified contractor.
Insignia is not responsible for damage or injury
caused by incorrect installation or use.
CAUTION: Do not exceed the maximum weight indicated. This mounting system is intended for use only
with the maximum weights indicated. Use with products heavier than the maximum weights indicated
may result in collapse of the mount and its accessories, causing possible injury.
The weight of your TV must not exceed 100 lbs. (45.3 kg). The wall must be capable of supporting five times
the weight of your TV and wall mount combined.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from young
children!
2
www.insigniaproducts.com
Tools needed
Edge-to-edge
stud finder
Level
Phillips screwdriver
Socket wrench with 1/2 in.
(13 mm) socket or adjustable
wrench
Measuring tape
Drill
7/32 in. (5.5 mm) wood drill
bit (for wood stud wall)
OR
3/8 in. (10 mm) masonry
drill bit (for solid concrete
or concrete block walls)
Hammer
Tap e
Pencil
Awl
Wall mount template
10 (1)
1 (2)
R
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.
ardware
You will need the following tools to assemble your new TV wall mount:
Package contents
Make sure that you have all the hardware necessary to assemble your new TV wall mount:
10 Wall Plate (1) 1 TV Brackets (2) R Wall Plate Template (1)
www.insigniaproducts.com
3
TV Hardware Bag
Label Hardware Qty.
22
34
44
54
64
TV Standoff
M6 × 12 mm
screw
M8 × 16 mm
screw
M8 × 20 mm
screw
M6 × 35 mm
screw
Label Hardware Qty.
74
84
94
11 2
12 2
M8 × 35 mm screw
M6/M8 washer
Spacers
5/16 in. × 2 3/4 in. lag bolt
Lag bolt washer
Concrete Installation Kit CMK1 (not included)
Contact customer service at 1-800-359-5520 to have these additional parts shipped directly to you.
C1 2
C2 2
C3 2
5/16 in. × 2 3/4 in. lag bolt
Lag bolt washer
Concrete anchors
Note: Deleted ruler.
4
www.insigniaproducts.com
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.
Installation instructions
STEP 1 - Determining whether your TV has a flat back or an
irregular or obstructed back
1 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from
damages and scratches.
2 If your TV has a table-top stand attached, remove the stand. See the documentation that came with your
TV for instructions.
3 Temporarily lay the TV brackets (1), oriented vertically, on the back of your TV.
4 Align the screw holes in the TV brackets with the mounting screw holes on your TV.
5 Identify which type of back your TV may have:
• Flat back: The brackets lay flush against the back of your TV and do not block any jacks. You do not need
spacers when assembling the wall mount.
• Obstructed back: The brackets block one or more of the jacks on the back of your TV. You will need
spacers when assembling the wall mount.
• Irregularly-shaped back: There is a gap between a bracket and some part of the back of your TV. You
will need spacers when assembling the wall mount.
6 Remove the TV brackets (1).
www.insigniaproducts.com
5
STEP 2 - Select screws, washers, and spacers
Screw is too
long
Screw fits
correctly
Screw is too
short
1 Select the hardware for your TV (screws, washers, and spacers). A limited number of TVs come with
mounting hardware included. (If there are screws that came with the TV, they are almost always in the
holes on the back of the TV.) If you don't know the correct length of the mounting screws your TV
requires, test various sizes by hand threading the screws.
Select one of the following types of screws:
For a TV with a flat back:
M6 X 12mm screws (3)
M8 X 16mm screws (4)
M8 X 20mm screws (5)
For a TV with an irregular/obstructed back:
M6 X 35mm screws (6)
M8 X 35mm screws (7)
Select an M6/M8 washer (8) for each screw.
For an irregular or obstructed TV back, also use the spacers (9)
CAUTION: To avoid potential personal injuries and property damage, make sure that there are adequate
threads to secure the brackets to your TV. If you encounter resistance, stop immediately and contact customer
service. Use the shortest screw and spacer combination to accommodate your TV. Using hardware that is too long
may damage your TV. However, using a screw that is too short may cause your TV to fall from the mount.
2 Remove the screws from the holes in the back of your TV.
3 For a flat back TV, go to “STEP 3 - Option 1: Attaching the mounting hardware to TVs with a flat back“ on
page 7.
-ORFor an irregular or obstructed back, go to “STEP 3 - Option 2: Attaching the mounting hardware to TVs
with irregular or obstructed backs” on page 8.
6
www.insigniaproducts.com
Loading...