Loading...
FA464DR
64 Transmitter / 16-Output Receiver
Installation Instructions
02039F
|
Document revision history / Notes |
|
|
|
|
Rev. Level |
Description |
Date |
B |
Create F:\Eng\parts\02039\E02039B.doc from |
6/01 |
|
P:\Master.dox\FA_dox\FA464.doc (pre-ECN) |
|
|
|
|
C |
Create F:\Eng\parts\02039\02039C.doc from |
7/25/01 |
|
F:\Eng\parts\02039\E02039B.doc (ECN release version) |
|
|
|
|
D |
Replace ISO logo |
7/25/01 |
|
|
|
E |
Revise per ECN 2259 |
10/24/02 |
|
|
|
F |
Add wire gauge p. 4; delete FA200/FA200W p.12 |
11/21/03 |
|
|
|
Important Notes
nThis product is designed to be installed and maintained by professional security technicians.
nUnless specifically noted, Inovonics products are intended for indoor use. This receiver is intended for use with indoor security systems. Use in outdoor applications may impair performance.
nTest system regularly.
© 1999 Inovonics Wireless Corporation 02039F.DOC LIT-FA464-INSTALL |
1 |
hc:21-Nov-03 |
FA464DR
64-Transmitter, 16-Relay Output Receiver
The FA464DR receiver has 16 Form C relay outputs, plus a global fault relay output.
Installers should note that alarm relay terminals are mounted so that normally open or normally closed terminal positions are side-by-side as shown in Figure 1.
TRANSMITTER PROGRAMMING PORT
REVIEW STATUS BUTTON
VALID DECODE LED
DECODE LED
OUTPUT LEDS 1-16
ADVANCE BUTTON
DELETE BUTTON
GLOBAL FAULT LED
FA104 PROGRAMMER PORT
RESET BUTTON
POWER LED
TRANSMITTER NUMBER DISPLAY
TAMPER SWITCH
TRANSMITTER STATUS LEDS
DECODE |
|
|
TRANSMITTER |
DC POWER ONLY |
TAMPER |
|
|
|
|
PROGRAMMING |
|
||||
VALID |
|
|
|
|
|
|
|
|
|
|
TAMPER |
12VDC TYPICAL 18VDC MAX |
|||
|
|
|
TRANSMITTER |
RESET |
+ |
||
|
OUTPUT |
|
NUMBER |
GND |
|||
|
1 |
|
ACTIVATED |
|
|
||
DECODE |
|
|
|
|
|
|
|
|
REVIEW |
|
|
|
|
|
|
|
|
TAMPERED |
|
|
|
|
|
|
2 |
STATUS |
|
NC |
NC |
|
|
|
|
|
|
1 |
|||
|
3 |
|
LOW BATTERY |
16 |
COM |
COM |
|
|
|
|
|
NO |
NO |
|
|
|
|
|
INACTIVE |
|
|
||
|
|
|
|
NO |
NO |
|
|
|
4 |
ADVANCE |
DELETE |
|
|
||
|
|
|
COM |
COM |
|
||
|
|
|
|
15 |
2 |
||
|
|
|
PROGRAMMED |
|
NC |
NC |
|
|
|
|
|
|
|
|
|
5 |
|
NC |
NC |
|
6 |
14 |
COM |
COM |
3 |
|
NO NO |
NO NO |
|
|
7 |
|
|
||
|
COM |
COM |
|
|
8 |
13 |
4 |
||
|
NC |
NC |
|
|
|
|
|
||
|
NOTE: |
|
|
|
|
NORMALLY OPEN TERMINALS |
|
|
|
9 |
ARE SIDE-BY-SIDE |
|
|
|
|
|
|
|
|
10 |
(8 PLACES) |
|
|
|
|
NC |
NC |
|
|
|
12 |
5 |
||
11 |
COM |
COM |
||
|
|
|
|
|
12 |
|
NO |
NO |
|
|
NO |
NO |
|
|
|
|
|
||
|
11 |
COM |
COM |
6 |
13 |
|
NC |
NC |
|
|
10 |
NC |
NC |
7 |
14 |
COM |
COM |
||
15 |
|
NO |
NO |
|
|
NO |
NO |
|
|
|
9 |
8 |
||
16 |
COM |
COM |
||
|
FAULT |
NC |
NC |
|
|
|
|
||
FA104 |
NC |
PROGRAMMER |
|
RESET |
COM FAULT |
POWER |
NO |
|
|
PROGRAMMER |
FA464D |
FA116 |
|
FA116 PROGRAMMER PORT |
DATA LED |
EXTERNAL TAMPER INPUT
POWER INPUT
RESET INPUT
ALARM OUTPUTS
1-4 and 13-16
WIRING HARNESS
TIE-DOWN HOLES (2 PLACES)
ALARM OUTPUTS
5-8 and 9-12
FAULT OUTPUT
Figure 1
Note: References in this manual to features shown in Figure 1 will be printed in bold italics.
© 1999 Inovonics Wireless Corporation 02039F.DOC LIT-FA464-INSTALL |
2 |
hc:21-Nov-03 |
Features of the FA464DR include:
x Full supervision of up to 64 FA transmitters.
x The FA464DR has 16 Form C Alarm Output Relays, plus a global Fault Output Relay.
x Transmitter, receiver and output options are factory assigned. They may be changed with the FA116 Executive Programmer or with the FA104 (upgraded C104) programmer.
x Intelligent global fault output for tamper, low battery and inactive transmitters. For example, if one of the alarm outputs is assigned to monitor low battery faults, the fault output automatically becomes tamper and inactive only.
x Manual and/or electronic reset of the receiver.
x Factory default programming: "Alarm" and "Inactive" outputs are programmed to follow transmitter status; "Tamper" and "Low battery" outputs are latching. Latched outputs require the receiver to be reset.
x Simple restoral to factory defaults.
x Automatic exit from programming after 4 minutes of inactivity.
x Transmitter Status LEDs show transmitter activation, tamper, low battery and inactive.
x The Programming LED blinks when the point IS NOT programmed, is on steady when the point IS programmed.
© 1999 Inovonics Wireless Corporation 02039F.DOC LIT-FA464-INSTALL |
3 |
hc:21-Nov-03 |
Technical Specifications:
Dimensions (housing): |
11" x 8.5" x 1.75" |
||
Weight: |
34 oz |
|
|
Environmental: |
|
|
|
Operating temperature: |
q |
q |
q q |
32 -140 F (0 -60 C) |
|||
Relative Humidity: |
90% (non-condensing) |
||
Electrical: |
|
|
|
Power Requirement: |
12-17 VDC, 980mA |
||
Minimum: |
60 Ma |
|
|
Output relay rating: |
1A @ 28 VDC, 0.5A @ 30 VAC (resistive) |
||
Wire gauge: |
14-22 AWG |
|
|
Receiver: |
|
|
|
Type: |
frequency-hopping spread spectrum |
||
Operating frequency: |
902-928 MHz |
||
Installation:
Power: Supply power and ground to designated terminals on the Power Input terminals.
Note: To power the FA464DR directly from an AC power source, Inovonics recommends a power supply that is UL listed for use with “Burglar Alarm Systems.”
Mounting: Use supplied hardware to attach FA464DR housing to wall or surface.
RECEIVER COVER SCREW ACCESS |
WALL MOUNT SCREW ACCESS |
||||
(2 PLACES) |
(2 PLACES) |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
© 1999 Inovonics Wireless Corporation 02039F.DOC LIT-FA464-INSTALL
Figure 2
4
hc:21-Nov-03
Connecting to a panel: When the FA464DR will be used with a hardwire security panel, the panel will typically supply power and ground to the FA464DR (if the power supply provides the required current).
Typical connections between the FA464DR and a hardwire panel:
The installer wires the relay common terminal to the panel Zone Return, and wires either the Normally Open or the Normally Closed terminal of the relay to the panel Zone input terminal.
TRANSMITTER
PROGRAMMING
TRANSMITTER
NUMBER
REVIEW
STATUS
ADVANCE DELETE
|
FA464DR |
|
|
DC POWER ONLY |
TAMPER |
|
|
|
TAMPER |
12VDC TYPICAL 18VDC MAX |
|
|
RESET |
+ |
ACTIVATED |
GND |
|
TAMPERED |
|
NC |
NC |
|
|
|
1 |
||
LOW BATTERY |
16 |
COM |
COM |
|
INACTIVE |
|
NO |
NO |
|
|
NO |
NO |
|
|
|
|
|
||
|
15 |
COM |
COM |
2 |
PROGRAMMED |
|
NC |
NC |
|
|
NC |
NC |
|
|
|
|
|
||
|
14 |
COM |
COM |
3 |
|
|
NO NO |
NO NO |
|
|
13 |
COM |
COM |
4 |
|
|
NC |
NC |
|
13.6VDC 
GROUND
PANEL ZONE 1 ZONE 1 RETURN
PANEL ZONE 2
ZONE 2 RETURN
PANEL
NOTE: GROUND
AND RETURNS
ARE NOT COMMON
In this example, Panel Zones 1 and 2 are configured to be N/C.
Figure 3
© 1999 Inovonics Wireless Corporation 02039F.DOC LIT-FA464-INSTALL |
5 |
hc:21-Nov-03 |
Programming transmitters:
Without the FA116 programmer:
1.Refer to Appendix A to determine available default parameters.
2.Select a point number which matches desired transmitter parameters.
3.Press the Advance Button on the FA464DR until the Transmitter Number Display shows the desired transmitter number. (Hold down the Advance Button for auto repeat.) The Programming LED will blink if the point has not been programmed. If a transmitter has already been programmed to that channel, the LED will be on steady.
4.Connect the programming cable to the transmitter and then to the Transmitter Programming Port on the FA464DR.
5.Press the transmitter reset button. (Refer to.) When the transmitter is successfully programmed, the receiver will emit a single "deedle" tone and the Programming LED will be on solid. (It may be necessary to press the transmitter reset button more than once, if the receiver is "busy" with signals from other transmitters.)
With the FA116 programmer: Up to 64 transmitters can be selected, programmed and deleted. The programmer allows installers to configure receiver parameters and output options. Point status and signal strength can be observed. Receiver outputs can be activated for testing and faults can be cleared.
Refer to FA116 programming documentation.
© 1999 Inovonics Wireless Corporation 02039F.DOC LIT-FA464-INSTALL |
6 |
hc:21-Nov-03 |
Loading...