Ingersoll-Rand 66301-XXX User Manual
OPERATOR’S MANUAL 66301-XXX
INCLUDING: SERVICE KITS, TROUBLESHOOTING, PARTS LIST,
DISASSEMBLY & REASSEMBLY.
TWO-BALL STYLE
LOWER PUMP ENDS
Also covers 637306-X43 service kits
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
RELEASED: 12-15-95
REVISED: 6-2-10
(REV. E)
SERVICE KITS
Use only genuine ARO® replacement parts to assure com-
y
patible pressure rating and longest service life.
637306-X43 for general repair of 66301-XXX lower pump
y
ends.
GENERAL DESCRIPTION
WARNING
PRESSURE AS INDICATED ON PUMP MODEL PLATE.
WARNING
FOR ADDITIONAL SAFETY PRECAUTIONS AND IMPORTANT INFORMATION.
This manual only covers the lower pump section. It is one
y
of four documents which support an ARO pump. Replacement copies of these forms are available upon request.
650XXX-X Pump Model Operator’s Manual.
General Information for Air Operated or Hydraulically
Lower Pump End Operator’s Manual.
:
Air or Hydraulic Motor Operator’s Manual.
The two-ball design provides better priming of the lower
y
foot valve. The double acting feature is standard in all
ARO industrial pumps. Material is delivered to the pump
discharge outlet on both the up and down stroke.
DO NOT EXCEED MAXIMUM OPERATING
REFER TO GENERAL INFORMATION SHEET
Operated Pumps.
MAINTENANCE
LOWER PUMP END DESCRIPTION CHART
66301 - X X X
Packing Material
3 - Glass lled PTFE (upper and lower)
C - UHMW-PE (upper and lower)
G - UHMW-PE / Leather staggered (upper and lower)
P - UHMW-PE / Glass lled PTFE staggered (upper)
- UHMW-PE (lower)
R - Glass lled PTFE / UHMW-PE staggered (upper)
- Glass lled PTFE (lower)
Spring Arrangement
4 - Multiple wave spring with 316 stainless steel balls
7 - Multiple wave spring with 440 stainless steel balls
Plunger Type
3 - Hardened stainless steel with hard chrome plating
B - Hardened stainless steel with ceramic coating
Service Kit Selection
Example: Lower Pump End # 66301-C43
Service Kit # 637306-C43
66301 - X X X
637306 - X 4 3
Packing
TROUBLE SHOOTING
No material at outlet (pump continually cycles).
Check material supply. Disconnect or shut o the air sup-
y
ply and replenish the material, reconnect.
The air / hydraulic motor is completely separate from the
lower pump end. This helps to keep the motor from being
contaminated by the material being pumped. Periodically,
ush entire pump system with a solvent that is compatible
with the material being pumped.
Keep solvent cup lled with this compatible solvent. This will
keep material from drying on the piston rod, which would
drag thru the packings, ruin them and eventually scour the
piston rod.
Provide a clean work surface to protect sensitive internal
moving parts from contamination from dirt and foreign matter during disassembly and reassembly.
Before reassembling, lubricate parts as required. When assembling “O” rings, or parts adjacent to “O” rings, exercise
care to prevent damage to “O” rings and “O” ring groove surface.
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX(800) 892-6276
www.ingersollrandproducts.com
© 2010
CCN 99434599
Material on one stroke only (fast downstroke).
The (21) lower ball may not be seating in the (22) seat (see
y
lower pump disassembly). Remove the ball from the seat,
clean and inspect the ball and seat area. If the ball or seat
is damaged, replace.
Material on one stroke only (fast upstroke).
Check for worn or damaged packings and seals. Replace
y
the packings and seals as necessary.
Material leakage out of the solvent cup or material appears on the pump plunger rod.
Relieve the pressure in the pump and tighten the solvent
y
cup until leakage discontinues. If this procedure does not
aid in stopping the leakage problem, the upper packings
may be worn (see lower pump disassembly). Replace the
packings as necessary.
PARTS LIST / 66301-XXX
Item Description
1 Solvent Cup (1) 94173 [SS]
6 Outlet Body (1) 94169 [SS]
8 “O” Ring
9
9
Tub e
15 Inlet Body (1) 94204 [SS]
21
Ball
22 Seat (1) 94170 [TC]
23 “O” Ring
9
26
Plunger Rod
27 Ball
28 Seat (1) 91076 [TC]
33 Piston (1) 94206 [SH]
36 Adapter (1) 94235 [SH]
43 Wave Spring (1) 94138 [SH]
44 Washer (1) 94192 [SS]
46 Washer (1) 94213 [SS]
[CSH] = Ceramic Coated Hard Stainless Steel [PSS] = Hard Chrome Plated Stainless Steel
[CSS] = Ceramic Coated Stainless Steel [SH] = Hard Stainless Steel
[GFT] = Glass lled PTFE [SS] = Stainless Steel
[L] = Leather [T] = PTFE
[PPS] = Polyphenylene Sul de [TC] = Tungsten Carbide
[PSH] = Hard Chrome Plated Hard Stainless Steel [UH] = UHMW-PE
(size)
(1/16” x 2-1/4” o.d.)
(66301-XX3)
(66301-XXB)
(1-3/16” o.d.) (66301-X4X)
(66301-X7X)
(1/16” x 1-5/8” o.d.)
(66301-XX3)
(66301-XXB)
(11/32” o.d.)
MATERIAL CODE
(Qty) Part No. [Mtl] Item Description
(3) Y328-34 [T]
(1) 94178 [PSS]
(1) 94178-2 [CSS]
(1) 90949 [SS]
(1) Y16-138 [SH]
(1) Y328-29 [T]
(1) 90297-1 [PSH]
(1) 90297-2 [CSH]
(1) 94210 [TC]
LOWER PUMP DISASSEMBLY
IMPORTANT: The lower pump is designed so that access to
the packings can be accomplished without disassembly of
the inlet / outlet bodies from the main pump tube. Complete
lower pump disassembly should not be necessary, in most
cases skip disassembly steps 3, 4 and 5 below.
NOTE: All threads are right hand.
Secure the lower pump assembly in a vise, clamping on
1.
the (6) outlet body.
Loosen the (1) solvent cup and unscrew the (74) nut and
2.
remove the assembly from the lower pump.
Remove the (8) “O” ring from the (6) outlet body. Set this
3.
assembly aside.
Unscrew the (15) inlet body and remove from the (9)
4.
tube.
Unscrew the (9) tube from the (6) outlet body and re-
5.
move the two (8) “O” rings.
Remove the (26) plunger and components from the (9)
6.
tube. Remove the (6) outlet body from the vise.
Secure the (26) plunger and components in a vise and
7.
unscrew the (33) piston from the plunger.
Remove the (46) washer, (47) bowed washer, (57) male
8.
packing washer, (55 and 56) “V” packings and (54) female
packing washer.
Unscrew the (36) adapter from the (33) piston, releasing
9.
the (28) seat and (27) ball.
Secure the (74) nut in a vise and unscrew the (1) solvent
10.
cup.
Remove the (77) bushing, (44) washer, (50) female pack-
11
.
ing washer, (51 and 52) “V” packings, (53) male packing
washer and (43) wave spring.
(size)
47 Bowed Washer (1) 90588 [SS]
50 Female Packing Washer (1) 94201-2 [PPS]
51
9
“V” Packing
52
9
“V” Packing
53 Male Packing Washer (1) 94200 [SS]
54 Female Packing Washer (1) 94203-2 [PPS]
55
9
“V” Packing
56
9
“V” Packing
57 Male Packing Washer (1) 94272 [SS]
70 Inlet Adapter (1) 94236 [SS]
74 Nut (1) 94166 [SS]
77 Bushing (1) 94181-2 [PPS]
Items included in Service Kit 637306-X43
9
Secure the (15) inlet body in a vise and unscrew the (70)
12.
(66301-3XX, -RXX)
(66301-CXX, -GXX, -PXX)
(66301-3XX, -PXX)
(66301-CXX, -RXX)
(66301-GXX)
(66301-3XX, -RXX)
(66301-CXX, -GXX, -PXX)
(66301-3XX, -RXX)
(66301-CXX, -PXX)
(66301-GXX)
(Qty) Part No. [Mtl]
(3) 93687-2 [GFT]
(3) 93687-4 [UH]
(2) 93687-2 [GFT]
(2) 93687-4 [UH]
(2) 93687-1 [L]
(3) 93688-2 [GFT]
(3) 93688-4 [UH]
(2) 93688-2 [GFT]
(2) 93688-4 [UH]
(2) 93688-1 [L]
inlet adapter, releasing the (22) seat, (23) “O” ring and (21)
ball.
LOWER PUMP REASSEMBLY
NOTE: Inspect and replace old parts with new parts as necessary. Look for deep scratches on metallic surfaces and nicks
or cuts in “O” rings and packings. Refer to sealant and torque
notes in gure 1.
Secure the (74) nut in a vise and insert the (43) wave
1.
spring, (53) male packing washer, (51 and 52) “V” packings, (50) female packing washer and (44) washer into
the (74) nut.
Place the (77) bushing into the (1) solvent cup and screw
2.
the (1) solvent cup into the (74) nut. Do not tighten.
3.
Secure the (6) outlet body in a vise and place the (8) “O”
ring at the bottom of the (74) nut and screw into the (6)
outlet body. Tighten the (74) nut to 150 ft lbs. (203.4 Nm).
4.
Slide the (26) plunger rod into the (1) solvent cup and
through the upper packing. Be careful not to damage
the packings.
5.
Assemble the (33) piston by placing the (54) female
packing washer, (55 and 56) “V” packings, (57) male packing washer, (47) bowed washer and (46) washer onto (33)
piston.
6.
Screw the (33) piston assembly into the (26) plunger
rod and tighten to 20 ft lbs. (27.12 Nm), place the (27)
ball, and (28) seat into the (33) piston and screw the (36)
adapter into place and tighten to 20 ft lbs. (27.12 Nm).
7.
Place the (8) “O” rings at each end of the (9) tube and slide
the (9) tube over the lower piston assembly and screw
into the (6) outlet body. Tighten to 300 ft lbs. (406.8 Nm).
8.
Screw the (15) inlet body onto the (9) tube and tighten
to 300 ft lbs. (406.8 Nm).
9.
Place the (21) ball, (23) “O” ring and (22) seat into the (15)
inlet body and screw the (70) inlet adapter into the (15)
inlet body and tighten to 300 ft lbs. (406.8 Nm).
10
Tighten the (1) solvent cup.
.
Page 2 of 4 66301-XXX (en)
Loading...