ikan PT3000 User Manual

Features you need, Prices you want.

PT3000 15” Teleprompter

User Guide

3903 Stoney Brook Dr. Houston TX 77063

Tel: [phone]

Fax: [phone]

www.ikancorp.com

[e-mail]

© 2009 ikan Corporation. All right reserved.

PT3000 15” T E L E PROMP T E R

1 of 10

INTRODUCTION

Thank you for purchasing the ikan PT3000 15” Teleprompter. The PT3000 is extremely easy to use and will quickly become an
integral part of your production kit. For more information on this and many other innovative ikan products, please visit our website:
www.ikancorp.com.

PACKAGE INCLUDES

 15” LCD Monitor Kit (including AC Adapter and Power Cord)
 Prompter Hood Kit (includes 2 piece hood and 3 velcro strips)
 PrompterPro Software
 User Guide
 Teleprompter Parts:

A

B C D

Checked by

 2 x 3/8-16 Receiving Nut

E

 2 x 1/4-20 Receiving Nut

F G H

 2 x 3/8-16 Screw  2 x 1/4-20 Screw

I

 L-Bracket (S)

M

J

 L-Bracket (L)

 12 x T-Plate

 32 x Phillips Head Screw(L)

K

 8 x T-Slot Nut

 8 x Phillips Head Screw(S)

L

 2 x 100mm Mounting Bracket

(1 for Optional Battery Mount
1 for Monitor Mount)

N

 Prompter Glass Frame

O

 8” T-Slot

P

 8” T-Slot with Metal Bracket

(Optional Tripod Mount)

Additional Tool Needed:

 10” T-Slot

** Not all parts needed for this teleprompter
assembly, depends on your camera and
tripod.

 20” T-Slot with Metal Bracket

CONDITIONS OF WARRANTY SERVICE

• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.

• The components and maintenance service fee will be charged if the warranty period has expired.

Free Service will not be Provided in the Following Situations:

• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.

• Damage caused by natural disaster, abnormal voltage, and environmental factors etc.

3903 St oney B ro ok D r. H ou ston T X 77 063 | +1.7 13 .2 72.8 82 2 | ww w.ik an corp .c om | s up port @i ka ncor p. com | © 2009 i kan Co rp orat io n. Al l righ t rese rv ed.

(* Even if the product is still within the warranty period.)

PT3000 15” T E L E PROMP T E R

2 of 10

ASSEMB LY INSTRU C T ION

Attach the 100mm Mounting Bracket (Part K) to the back
of the 15” monitor using 4 x Short Phillip’s head screws

1

(Part H). The two flaps of Part K should be perpendicular
to the monitor control buttons.
Attach 4 x T-slot Nuts (Part D) and 4 x Long Phillips Head
Screws (Part G) as shown on the diagram.

Part-H

Part-DPart-G Part-G

Part-H

Part-K

Rear view of 15” monitor

PT3000

Remove protective film from Part-L.

2

> Unscrew the 4 small screws
that are pre-placed in Part L.
> Remove glass holding tabs on
both sides.

> Peel the protective film away.
> Re-install the teleprompter glass back
into the metal frame.

Part-L

Attach Short L-Bracket (Part I) to 8” T-slot (Part M)
using 2 x T-plates (Part C) and 4 x Long Phillips head

3

screws (Part G). Refer to illustration below for configu­ration. The Short L-Bracket’s (Part I) top half should be
flush with the edge of the 8” T-slot (Part M).

Part-I

Part-C

Part-M

Part-G

Attach the 20” T-slot with Metal Bracket (Part P) to the
assembled parts. You will use 2 x T-plates (Part C) and

4

4 x Long Phillips Head screws (Part G) to do so. Make
sure to evenly tighten all screws in this assembly.

Part-G

Part-P

Part-C

3903 St oney B ro ok D r. H ou ston T X 77 063 | +1.7 13 .2 72.8 82 2 | ww w.ik an corp .c om | s up port @i ka ncor p. com | © 2009 i kan Co rp orat io n. Al l righ t rese rv ed.

PT3000 15” T E L E PROMP T E R

3 of 10

ASSEMB LY INSTRU C T ION

Attach Long L-Bracket (Part J) to the assembled parts. Make sure to arrange the long section of Part J as shown in the
illustration, otherwise there will not be adequate room to place the monitor. You will use 4 x Long Phillips head screws

5

(Part G) and 2 x T-plates (Part C) to attach it. Then, you will use 4 x Long Phillips head screws (Part G) and 2 x T-plates
(Part C) to attach the 10” T-slot (Part O). Make sure to evenly tighten all screws in the assembly.

ikancorp.com

Part-C

Part-G

Part-O

Part-J

Part-G

Slide the Monitor with mounting bracket onto the 10” T-slot (Part O), aligning the T-slot Nuts with the T-slots of Part O.
Refer to the diagram below.

6

ikancorp.com

Side View

Part-M



 

VGA Cable

Part-O

Part-P

 

ikancorp.com

Note: The VGA cable will not connect to the monitor if the monitor is slid
all the way flush to Part-M. You must connect the cable before tightening
down the monitor to insure a proper fit for the connections.

3903 St oney B ro ok D r. H ou ston T X 77 063 | +1.7 13 .2 72.8 82 2 | ww w.ik an corp .c om | s up port @i ka ncor p. com | © 2009 i kan Co rp orat io n. Al l righ t rese rv ed.