Icom UT-133, UT-133A Instructions Manual

Bluetooth® UNIT

Bluetooth

®

UT-133

Transceiver

UT-133

INSTRUCTIONS

Thank you for purchasing the UT-133 Bluetooth® u n i t .
Installing the UT-133 in a transceiver allows you to
use a variety of Bluetooth

®

devices.
Please read this instructions carefully and complete­ly before installing the UT-133.

About the UT-133

The UT-133 is a Bluetooth® unit to be installed in a trans­ceiver to communicate with other Bluetooth® devices.
Please refer to the transceiver’s instruction manual for de­tails regarding installation and use of the UT-133 with the
transceiver.

Android® device

VS-3

(third party)

Electromagnetic Interference

When you use a Bluetooth® device, pay attention to follow­ing:
Bluetooth® devices operate on the 2.4 GHz band.
The 2.4 GHz band is also used by other devices, such as
wireless LAN products, microwave ovens, RFID systems,
amateur radio stations, and so on.
When using a transceiver with the UT-133 installed and
turned ON near such devices, interference may occur, caus­ing a decrease in communication speed, and an unstable
connection.
In such cases, use the transceiver with the UT-133 away
from the other devices, or stop using those devices.

Precautions

The Bluetooth® communication range may vary, depending
on the environment in which the device operates. Micro­wave ovens or wireless LAN may cause an interference.
In that case, stop using those devices or move away the
Bluetooth® device from the other devices.
This Bluetooth® device has a range of use. If the communi­cation is unstable, use the device within the range.

DO NOT put anything on top of the unit, before installing.
DO NOT drop, impact or vibrate the unit, before installing.

This may damage to the unit.
You may not be able to use some Bluetooth® device’s func­tion, even if the unit is installed.

Radio operator warnings

• Do not use a transceiver with the UT-133 installed and

turned ON near medical equipment, or near a person who
has a pacemaker. Radio waves from the transceiver may
cause interference, or endanger their life.

• Do not use a transceiver with the UT-133 installed and

turned ON near microwave ovens. Interference may occur.

• Do not make any changes or modications to the unit.

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom
Incorporated (Japan) in Japan, the United States, the United King­dom, Germany, France, Spain, Russia and/or other countries.
The Bluetooth® work mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by Icom
inc. is under license.
All other products or brands are registered trademarks or trade­marks of their respective holders.

Specifications

• Bluetooth® version: Bluetooth® Version 3.0

• Transmission Output: Class 1

• Supported proles: HFP, HSP, SPP

• The maximum number of paired Bluetooth® devices:

8 devices*

* You can pair with up to 8 headsets and

data devices. The 8 paired devices can­not be all headsets or all data devices.

• Dimensions: 20.0(W) x 35.0(H) x 5.3(D) mm
(0.79(W) x 1.38(H) x 0.21(D) inch)

• Weight: 3 g (0.11 oz) (approximately.)

• Device Name: Icom BT-001 (default value)

• Passkey: 0000 (four zeros)

The specications are subject to change without notice or

obligations.

FCC and IC information

• FOR CLASS B UNINTENTIONAL RADIATORS:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reason­able protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in ac­cordance with the instructions, may cause harmful interfer­ence to radio communications. However, there is no guaran­tee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and re-

ceiver.

• Connect the equipment into an outlet on a circuit differ­ent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV techni­cian for help.

CAUTION: Changes or modications to this device, not ex-
pressly approved by Icom Inc., could void your authority to
operate this device under FCC regulations.

This device complies with Part 15 of FCC and Industry Can­ada licence-exempt RSS standard(s). Operation is subject to

the following two conditions: (1) this device may not cause in­terference, and (2) this device must accept any interference,
including interference that may cause undesired operation
of the device.
This transmitter must not be co-located or operated in con-

junction with any other antenna or transmitter.

CAN ICES-3 (B)

• For Mobile Use

This equipment complies with FCC/IC radiation exposure

limits set forth for an uncontrolled environment and meets

the FCC radio frequency (RF) Exposure Guidelines and
RSS-102 of the IC radio frequency (RF) Exposure rules. This

equipment has very low levels of RF energy that it deemed

to comply without maximum permissive exposure evaluation

(MPE).

Cet équipement est conforme aux limites d’exposition aux

rayonnements énoncées pour un environnement non contrôlé

et respecte les règles les radioélectriques (RF) de la FCC

lignes directrices d’exposition et d’exposition aux fréquenc­es radioélectriques (RF) CNR-102 de l’IC. Cet équipement

émet une énergie RF très faible qui est considérée conforme
sans évaluation de l’exposition maximale autorisée.

• For Portable Use

This equipment complies with FCC/IC radiation exposure

limits set forth for an uncontrolled environment and meets

the FCC radio frequency (RF) Exposure Guidelines and
RSS-102 of the IC radio frequency (RF) Exposure rules. This

equipment has very low levels of RF energy that are deemed

to comply without testing of specic absorption ratio (SAR).

Cet équipement est conforme aux limites d’exposition aux

rayonnements énoncées pour un environnement non contrôlé

et respecte les règles les radioélectriques (RF) de la FCC

lignes directrices d’exposition et d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet

une énergie RF très faible qui est considérée conforme sans
évaluation du débit d’absorption spécique (DAS).

After installing the UT-133, place the FCC/IC ID label on the
outside of the transceiver.

Le présent appareil est conforme aux la partie 15 des règles
de la FCC et CNR d'Industrie Canada applicables aux appar­eils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes: (1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Cet émetteur ne doit pas être co-localisé ou fonctionner en

conjonction avec une autre antenne ou émetteur.

NMB-3 (B)

About CE

Versions of the UT-133 which display the “CE”
symbol on the serial number label, comply with
the essential requirements of the Radio and
Telecommunications Terminal Equipment Di-

rective, 1999/5/EC, and the restriction of the

use of certain hazardous substances in electri-

cal and electronic equipment Directive, 2011/65/

EU.

You can get the DOC (Declaration Of Conformity) from your
nearest Icom dealer. See the Icom website for details of your
nearest dealer.

http://www.icom.co.jp/world/

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

A-7142H-1EX-q

© 2014 Icom Inc.