Icom IC-FR3000, IC-FR4000 User guide

REMOTE CONTROL MANUAL

VHF FM REPEATER

iFR3000

UHF FM REPEATER

iFR4000

1 REMOTE CONTROL FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1

1-1 REMOTE CONTROL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1-2 REMOTE CONTROL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1-3 COMMAND TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1-4 COMMAND DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1-5 OPERATION EXAMPLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1-6 OPERATION EXAMPLE FOR PHONE PATCH . . . . . . . . . . . . . . . . 12

REMOTE CONTROL FUNCTION

1

1

1-1 REMOTE CONTROL SETTING

DD

System control

To enable remote control functions the DTMF settings (RX System Code, TX System Code, DTMF Setting,
TX Code CH (Autodial), etc.) must be pre-programmed using CS-FR3000 cloning software. Use CS­FR3000 help screens for description of functions and operation and for programming details.

NOTE: Check the “Control” check-box to enable remote control operation using DTMF signals.

NOTE: Check the “TEL Function” check-box to enable remote control operation using DTMF signals

from the telephone line.

2

REMOTE CONTROL OPERATION

1

DD

System control command

NOTE: All commands must be entered within 10 sec. of entering a password. It is possible to enter the

password and command continuously.

Format of Command

• Basic command code

The Basic command code consists of a fixed 4-digit command code, preceded by a 1-digit Header Tone, and
followed by a 1-digit De-limiter Tone.

Header Tone

The Header tone is sent ahead of the command and indicates the start of the command. This tone is a
fixed 1-digit from 0—9, A—D, ∗(E), #(F) (programmed using CS-FR3000). The default setting is ∗(E).

De-limiter Tone

The De-limiter is sent between commands and at the end of remote control codes. This tone indicates a
space between segments of the command as well as the end of the command. This tone is a fixed 1-digit
from 0—9, A—D, ∗(E), #(F) (programmed using CS-FR3000). The default setting is #(F).

Command Code

This field indicates the pre-programmed command or action to be executed. These codes are pro­grammed to fixed 4-digit codes in cloning software, and may include characters from 0—9, A—D, ∗(E),
#(F).

• Command code with sub code

The Command code with Sub code consists of basic command code and sub code (additionally required
information).

Sub Code

This field is entered following the command code and indicates a memory channel number (for Memory
CH Select), an Autodial number (for Telephone Autodial), or a telephone number (for manual Tel dial com­mands). The Sub Code will be a fixed 2-digit code for Memory CH Select and Telephone Autodial com­mands or may be up to 24-digits for Tel dial command.

• Command with password and sub code continuously

This is the format required for entering commands for remote control operation.

Password

The Password is a type of command code. The FR3000/FR4000 will enter the “System Control standby
mode” when it receives this command while in normal operating mode. This is a fixed 4-digit code that
is programmed using cloning software and may include digits from 0—9, A—D, ∗(E), #(F).

Header

Tone

De-limiter

Tone

De-limiter

Tone

De-limiter

Tone

Password Command Code Sub Code

digits 11123 4

1123 4 1••••• N1

Header

Tone

De-limiter

Tone

De-limiter

Tone

Command Code Sub Code

digits 1111

••••• N123 4

Header

Tone

De-limiter

Tone

Command Code

digits 11123 4

1-2 REMOTE CONTROL OPERATION

3

REMOTE CONTROL OPERATION

1

1-3 COMMAND TABLE

Default

During During

Function

Code

Normal mode

Phone Patch mode

SUB code

Transceiver

Phone

Transceiver

Phone

System Control Exit 0002 ✔✔ ✔

†

✔ —
Repeat Start 0003 ✔✔ —— —
Repeat Stop 0004 ✔✔ —— —

TX Start 0005 — ✔

‡

—

†

✔

‡

—

TX Stop 0006 — — —

†

✔ —

RF Power (Low) 0007 ✔✔ —— —

RF Power (High) 0008 ✔✔ —— —

RX Unit OFF 0009 — ✔ —— —

RX Unit ON 0010 — ✔ —— —

TX/RX Unit OFF 0011 — ✔ —— —

TX/RX Unit ON 0012 — ✔ —— —

Master Enable 0013 ✔✔ —— —

Slave Enable 0014 ✔✔ —— —

TEL Dial 0015 ✔ — ✔ — Max. 24 digits of telephone number

TEL Autodial 0016 ✔ — ✔ —2 digits Autodial channel number

Mch Select 0017 ✔✔ ——2 digits Memory channel number

CPU All Reset 0018 — ✔ —— —

†

: When the Phone Patch mode is activated from the

telephone, the repeater may recognize signals
from a transceiver as being a signal from the tele­phone due to the sidetone function of the phone
line. This will depend on the telephone company
that provides local service.

‡

: “TX Start” is prohibited from the telephone line

when “Slave Enable” (the backup repeater) is
activated.

4

REMOTE CONTROL OPERATION

1

• System Control Exit

Turns OFF “System Control standby mode” and
returns to normal operating mode. Will also “Hang
up” the phone line during Phone Patch operation.

• Repeat Start

This command enables repeater operation. This
command is not available during Phone Patch
operation.

• Repeat Stop

This command inhibits repeater operation immedi­ately even while transmitting. May be cancelled by
entering “Repeat Start” command or power the
repeater OFF/ON. This command is not available
during Phone Patch operation.

• TX Start

This command initiates repeater transmit mode for
Phone Patch operation. This command is available
only when the signal is entered via the connected
telephone line.

• TX Stop

This command stops the repeater from transmitting
during Phone Patch operation. This command is
available only when the signal is entered via the
connected telephone line.

• RF Power (Low)

Switches TX power to “Low.” This command is not
available during Phone Patch operation.

• RF Power (High)

Switches TX power to “High.” This command is not
available for the channel which low power is pro­grammed by cloning or during Phone Patch opera­tion.

• RX Unit OFF

Turn OFF the RX unit (front end). This command is
not available from a transceiver or during Phone
Patch operation.

• RX Unit ON

Turn ON the RX unit (front end). This command is
not available from a transceiver or during Phone
Patch operation.

• TX/RX Unit OFF

Turn OFF the TX/RX units. This command is not
available from a transceiver or during Phone Patch
operation.

• TX/RX Unit ON

Turn ON the TX/RX units. This command is not
available from a transceiver or during Phone Patch
operation.

• Master Enable

Activates the master repeater when connected to a
back up repeater. This command is not available
during Phone Patch operation.

• Slave Enable

Activates the back up repeater when connected to
a master repeater. This command is not available
during Phone Patch operation.

• TEL Dial

Activates the phone line and dials the telephone
number entered as sub code (max. 24 digits).
Command will not activate when the first digit
entered is the same as programmed in “Call
Prohibition.” The repeater transmits “NG ACK” sig­nal. This command is only available from a trans­ceiver.

• TEL Autodial

Activates the phone line and dials the pre-pro­grammed autodial channel (2 digits) as sub code.
This command is only available from a transceiver.

• Memory CH Select

Selects the memory channel with sub code (2 dig­its Memory channel number). This command is not
available during Phone Patch operation.

• CPU All Reset

Resets the repeater’s CPU. This command is not
available from a transceiver or during Phone Patch
operation.

1-4 COMMAND DESCRIPTIONS

5

REMOTE CONTROL OPERATION

1

DD

Repeat Start (0003 Default)

This command is available from both the transceiv-
er and phone line. This explanation shows the step
by step operation from the transceiver or operation
from the phone line when entering the password and
command continuously (one after the other).

[From the Transceiver]

q Enter the programmed password from the trans-

ceiver.

Code: ∗0001#

• Verify the repeater replies “System Password OK
ACK (1111).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.

w Enter the “Repeat Start” command within 10 sec.

Code: ∗0003#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0003#).

• The repeater starts the repeater operation.

[From the Phone line]

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the following DTMF code.

Code: ∗0001#0003#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and
Repeat Start code are correct, and try again.

• The repeater starts the repeater operation.

e Hang up the phone, the repeater automatically

disconnects the phone.

DD

Repeat Stop (0004 Default)

This command is available from both the transceiv-
er and phone line. This explanation shows the oper­ation from the transceiver when entering the pass­word and command continuously or step by step
operation from the phone line (one after the other).

[From the Transceiver]

➥ Enter the following DTMF code from the trans-

ceiver.

Code: ∗0001#0004#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and
Repeat Stop code are correct, and try again.

• The repeater stops the repeater operation.

[From the Phone line]

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the programmed password.

Code: ∗0001#

• Verify the repeater replies “System Password OK
ACK (1111).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.

e Enter the “Repeat Stop” command within 10 sec.

Code: ∗0004#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0004#).

• The repeater stops the repeater operation.

r Hang up the phone, the repeater automatically

disconnects the phone.

1-5 OPERATION EXAMPLE

DD

System control command

NOTE:

•

All commands must be entered within 10 sec. of
entering a password. If the input time period
runs out, you must enter the password again.
This time period cannot be changed, so it is
possible to enter the password and command
continuously.

• When operating from the phone line the phone
must be able to send DTMF signals.

• When the command is available from the trans­ceiver and phone line, the operations are not
different from both them other than the connect­ing and disconnecting way to the repeater.

The following examples assume these codes
are pre-programmed in the repeater. Other
commands are same as default codes listed on
command table (p. 3).
System Password: 0001,
Header Tone: ∗, De-limiter Tone: #
System Password OK ACK: 1111
System Control Exit ACK: 2020
OK ACK: 3333, NG ACK: 4040

6

REMOTE CONTROL OPERATION

1

DD

RF Power (Low) (0007 Default)

This command is available from both the transceiv-
er and phone line. This explanation shows the step
by step operation from the transceiver or operation
from the phone line when entering password and
command continuously (one after the other).

This command cannot be performed while repeater
is transmitting, therefore you must stop the repeater
operation before changing RF power.

[From the transceiver]

q Enter the programmed password from the trans-

ceiver.

Code:

∗

0001#

• Verify the repeater replies “System Password OK
ACK (1111).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.

w Enter the “Repeat Stop” command within 10 sec.

Code: ∗0004#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0004#).

e Enter the “RF Power (Low)” command within 10

sec.

Code: ∗0007#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0007#).

• The repeater changes transmit power High to Low.

r Enter the “Repeat Start” command within 10 sec.

Code: ∗0003#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0003#).

[From the Phone line]

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the following DTMF code.

Code: ∗0001#0004#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and
Repeat Stop code are correct, and try again.

e Enter the “RF Power (Low)” command within 10

sec.

Code: ∗0007#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command again (Code:

∗

0001#0007#).

• The repeater changes transmit power High to Low.

r Enter the “Repeat Start” command within 10 sec.

Code: ∗0003#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command again (Code:

∗

0001#0003#).

t Hang up the phone, the repeater automatically

disconnects the phone.

OPERATION EXAMPLE (Continue)

7

REMOTE CONTROL OPERATION

1

DD

RF Power (High) (0008 Default)

This command is available from both the transceiv-
er and phone line. This explanation shows the oper­ation from the transceiver when entering the pass­word and command continuously or step by step
operation from the phone line (one after the other).

This command cannot be performed while repeater
is transmitting, therefore you must stop the repeater
operation before changing RF power.

[From the transceiver]

q Enter the following DTMF code from the trans-

ceiver.

Code:

∗

0001#0004#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and
Repeat Stop code are correct, and try again.

e Enter the “RF Power (High)” command within 10

sec.

Code: ∗0008#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0008#).

• The repeater changes transmit power Low to High.

r Enter the “Repeat Start” command within 10 sec.

Code: ∗0003#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0003#).

[From the Phone line]

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the programmed password.

Code: ∗0001#

• Verify the repeater replies “System Password OK
ACK (1111).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.

e Enter the “Repeat Stop” command within 10 sec.

Code: ∗0004#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0004#).

r Enter the “RF Power (High)” command within 10

sec.

Code: ∗0008#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0008#).

• The repeater changes transmit power Low to High.

t Enter the “Repeat Start” command within 10 sec.

Code:

∗

0003#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0003#).

y Hang up the phone, the repeater automatically

disconnects the phone.

OPERATION EXAMPLE (Continue)

8

REMOTE CONTROL OPERATION

1

DD

RX Unit OFF (0009 Default)

This command is available from the phone line
only. This explanation shows the step by step oper­ation. You can carry out the command operation
either step by step, or by entering the password and
command continuously.

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the programmed password.

Code:

∗

0001#

• Verify the repeater replies “System Password OK
ACK (1111).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.

e Enter the “RX Unit OFF” command within 10 sec.

Code: ∗0009#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0009#).

• The repeater turns the RX unit (front end) OFF.

r Hang up the phone, the repeater automatically

disconnects the phone.

DD

RX Unit ON (0010 Default)

This command is available from the phone line
only. This explanation shows entering the password
and command continuously. You can carry out the
command operation either step by step, or by enter­ing the password and command continuously.

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the following DTMF code.

Code:

∗

0001#0010#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and RX
Unit ON code are correct, and try again.

• The repeater turns the RX unit (front end) ON.

e Hang up the phone, the repeater automatically

disconnects the phone.

DD

TX/RX Unit OFF (0011 Default)

This command is available from the phone line
only. This explanation shows entering the password
and command continuously. You can carry out the
command operation either step by step, or by enter­ing the password and command continuously.

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the following DTMF code.

Code:

∗

0001#0011#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and TX/RX
Unit OFF code are correct, and try again.

• The repeater turns the TX/RX units OFF.

e Hang up the phone, the repeater automatically

disconnects the phone.

DD

TX/RX Unit ON (0012 Default)

This command is available from the phone line
only. This explanation shows the step by step oper­ation. You can carry out the command operation
either step by step, or by entering the password and
command continuously.

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the programmed password.

Code:

∗

0001#

• Verify the repeater replies “System Password OK
ACK (1111).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.

e Enter the “TX/RX Unit ON” command within 10

sec.

Code:

∗

0012#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0012#).

• The repeater turns the TX/RX units ON.

r Hang up the phone, the repeater automatically

disconnects the phone.

OPERATION EXAMPLE (Continue)

9

REMOTE CONTROL OPERATION

1

DD

Master Enable (0013 Default)

This command is available from both the transceiv-
er and phone line. This explanation shows the step
by step operation from the transceiver or operation
from the phone line when entering the password and
command continuously (one after the other).

[From the Transceiver]

q Enter the programmed password from the trans-

ceiver.

Code: ∗0001#

• Verify the repeater replies “System Password OK
ACK (1111).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.

w Enter the “Master Enable” command within 10

sec.

Code: ∗0013#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0013#).

• The operating repeater switches to the Master
repeater.

[From the Phone line]

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the following DTMF code.

Code: ∗0001#0013#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and
Master Enable code are correct, and try again.

• The operating repeater switches to the Master
repeater.

e Hang up the phone, the repeater automatically

disconnects the phone.

DD

Slave Enable (0014 Default)

This command is available from the transceiver and
phone line. This explanation shows the operation
from the transceiver when entering the password
and command continuously or step by step operation
from the phone line (one after the other).

[From the Transceiver]

➥ Enter the following DTMF code from transceiver.

Code: ∗0001#0014#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and Slave
Enable code are correct, and try again.

• The operating repeater switches to the Slave
repeater.

[From the Phone line]

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the programmed password.

Code: ∗0001#

• Verify the repeater replies “System Password OK
ACK (1111).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.

e Enter the “Slave Enable” command within 10 sec.

Code: ∗0014#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0014#).

• The operating repeater switches to the Slave
repeater.

r Hang up the phone, the repeater automatically

disconnects the phone.

OPERATION EXAMPLE (Continue)

10

REMOTE CONTROL OPERATION

1

OPERATION EXAMPLE (Continue)

DD

Mch Select (0017 Default)

This command is available from both the transceiv-
er and phone line. This explanation shows the step
by step operation from the transceiver or operation
from the phone line when entering the password and
command continuously (one after the other).

This command cannot be performed while repeater
is transmitting, therefore you must stop the repeater
operation before selecting a different memory chan­nel.

[From the transceiver]

q Enter the programmed password from the trans-

ceiver.

Code:

∗

0001#

• Verify the repeater replies “System Password OK
ACK (1111).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.

w Enter the “Repeat Stop” command within 10 sec.

Code: ∗0004#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0004#).

e Enter the “Mch Select” command followed by sub

code within 10 sec.

Code: ∗0017#07#

(when your intended channel is 07)

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0017#07#).

• The repeater changes to the memory channel 7.

r Enter the “Repeat Start” command within 10 sec.

Code: ∗0003#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0003#).

[From the Phone line]

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the following DTMF code.

Code: ∗0001#0004#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and
Repeat Stop code are correct, and try again.

e Enter the “Mch Select” command followed by sub

code within 10 sec.

Code: ∗0017#07#

(when your intended channel is 07)

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0017#07#).

• The repeater changes to the memory channel 7.

r Enter the “Repeat Start” command within 10 sec.

Code: ∗0003#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0003#).

t Hang up the phone, the repeater automatically

disconnects the phone.

11

REMOTE CONTROL OPERATION

1

DD

CPU All Reset (0018 Default)

This command is available from the phone line
only. This explanation shows entering the password
and command continuously.

This command cannot be performed while repeater
is transmitting, therefore you must stop the repeater
operation before performing CPU All Reset.

q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the following DTMF code.

Code: ∗0001#0004#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and
Repeat Stop code are correct, and try again.

e Enter the “CPU All Reset” command within 10

sec.

Code: ∗0018#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0018#).

• The repeater performs CPU All Reset.

r Enter the “Repeat Start” command within 10 sec.

Code: ∗0003#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0003#).

t Hang up the phone, the repeater automatically

disconnects the phone.

OPERATION EXAMPLE (Continue)

12

REMOTE CONTROL OPERATION

1

1-6 OPERATION EXAMPLE FOR PHONE PATCH

DD

Description

Phone Patch function allows communication to a
transceiver from a telephone line, or connection to a
telephone line from a transceiver. During the Phone
Patch operation, the voice communication is sim­plex. (The mute control is activated from the trans­ceiver’s continuous tone SQL.)

■ Operation from the transceiver

One of two methods (Dial and Auto-dial) of telephone
access is selectable from the transceiver.
Dial: Direct dialing from the keypad of a transceiver.
Auto-dial: Using the pre-programmed phone No. (up

to 20 channels are stored) in the repeater.

DD

TEL Dial (0015 Default)

q Enter the programmed password from transceiv-

er.

Code:

∗

0001#

• Verify the repeater replies “System Password OK
ACK (1111).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.

w Enter the “TEL Dial” command within 10 sec.

Code: ∗0015#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0015#).

e Enter the telephone number (if the number is 060-

3355-2244) as sub code within 10 sec.

Code: ∗06033552244#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0015#06033552244#).

• The repeater starts calling the number.

r When the connection has been con firmed, talk to

the phone by simplex voice communication.

t After conversation is finished enter the password

followed by the “System Control Exit” command to
terminate Phone Patch operation.

Code: ∗0001#0002#

• Verify the repeater replies “System Control Exit ACK
(2020),” then repeater hangs on the phone.

DD

TEL Autodial (0016 Default)

Autodial number: 12 (Channel 12)
q Enter the following DTMF codes.

Code: ∗0001#0016#12#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and com­mand code are correct, and try again.

• The repeater starts calling the autodial channel 12.

w When the connection has been con firmed, talk to

the phone by simplex voice communication.

e After conversation is finished enter the password

followed by the “System Control Exit” command to
terminate Phone Patch operation.

Code: ∗0001#0002#

• Verify the repeater replies “System Control Exit ACK
(2020),” then repeater hangs on the phone.

■ Operation from the phone line

DD

TX Start (0005 Default)

Step by step operation from the phone line.
q Dial the phone number of the phone line that the

repeater is connected to.

w When the connection has been con firmed, enter

the programmed password.

Code: ∗0001#

• Verify the repeater replies “System Password OK
ACK (1111).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.

e Enter the “TX Start” command within 10 sec.

Code: ∗0005#

• Verify the repeater replies “OK ACK (3333).”

• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:

∗

0001#0005#).

• The repeater starts the downlink transmission for
Phone Patch operation.

r After conversation is finished, hang up the phone,

the repeater automatically disconnects the phone
and stops the downlink transmission.

DD

TX Stop (0006 Default)

During Phone Patch operation this command stops
repeater from transmitting, for changing repeater settings.
q Enter the following DTMF code (password and

command code).

Code: ∗0001#0006#

• Verify the repeater replies “OK ACK (3333).”

• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and TX
stop code are correct, and try again.

w You may continue remote control operation from

the phone line to make other settings in the
repeater, or hang up the phone if there is nothing
else to change.

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

S-6228I-1US

© 2004 Icom Inc.