Icom IC-F22S, IC-F12S User Manual

INSTRUCTION MANUAL

UHF TRANSCEIVER

iF22/S

This device complies with Part 15 of the FCC rules. Oper­ation is subject to the following two conditions: (1) This de­vice may not cause harmful interference, and (2) this
device must accept any interference received, including in­terference that may cause undesired operation.

VHF TRANSCEIVER

iF12/S

i

FOREWORD

Thank you for purchasing the IC-F12/S, F22/S FM transceiver.
READ ALL INSTRUCTIONS carefully and completely before using
the transceiver.

SAVE THIS INSTRUCTION MANUAL–This instruction manual
contains important operating instructions for the transceiver.

IMPORTANT

R CAUTION! NEVER hold the transceiver so that the antenna is
very close to, or touching exposed parts of the body, especially the
face or eyes, while transmitting. The transceiver will perform best if
the microphone is 2 to 4 in. (5 to 10 cm) away from the lips and the
transceiver is vertical.

R CAUTION! NEVER operate the transceiver with a headset or
other audio accessories at high volume levels.

R CAUTION! NEVER short the terminals of the battery pack.

DO NOT push the PTT when not actually desiring to transmit.

AVOID using or placing the transceiver in direct sunlight or in areas

with temperatures below –10°C (+14°F) or above +50°C (+122°F).

DO NOT modify the transceiver for any reason.

KEEP the transceiver from the heavy rain, and Never immerse it in

the water. The transceiver construction is water resistant, not
water proof.

The use of non-Icom battery packs/chargers may impair transceiver
performance and invalidate the warranty.

FCC caution: Changes or modifications to this transceiver, not
expressly approved by Icom Inc., could void your authority to op­erate this transceiver under FCC regulations.

ii

TABLE OF CONTENTS

FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i

IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i

TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii

1 PANEL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–3

‘ Switches, controls, keys and connectors . . . . . . . . . . . . . . .1–2

‘ LED indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

2 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

3 BATTERY PACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–11

‘ Battery pack replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

‘ Battery cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

‘ Battery charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-9

‘ Charging NOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

‘ Battery case (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

44 PPRROOGGRRAAMMMMAABBLLEE FFUUNNCCTTIIOONNSS .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

12-16

‘ General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

5 CONVENTIONAL OPERATION . . . . . . . . . . . . . . . . . . . . . .17-18

‘ Receiving and transmitting . . . . . . . . . . . . . . . . . . . . . . . . . .17

‘ Call procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

‘ Transmitting notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

6 CLONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

7 OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-22

8 CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-24

1

PANEL DESCRIPTION

1

‘‘

Switches, controls, keys and
connectors

y

u

Speaker

Mic

w

e

r

t

i

2CH version

CH1↔CH2

16CH version

CH1 to CH16

q

SP

MIC

2

1

PANEL DESCRIPTION

q CHANNEL SELECTOR/SW [CH]

• 2CH version: Toggle the CH switch to select CH1 or CH2.

• 16CH version: Turn the selector knob to select the pro-

grammed operating channel.

w VOLUME CONTROL [OFF/VOL]

Turns power ON and adjusts the audio level.

e DEALER-PROGRAMMABLE KEY [Upper]

Can be programmed for one of several functions by your Icom
dealer.

r PTT SWITCH [PTT]

Push and hold to transmit; release to receive.

t DEALER-PROGRAMMABLE KEY [Lower]

Can be programmed for one of several functions by your Icom
dealer.

y ANTENNA CONNECTOR

Connects the supplied antenna.

u TX/RX INDICATOR LED (see p. 3)

• Lights red while transmitting.

• Lights green while receiving a signal, or squelch is open.

i [SP]/[MIC] JACK

Connects optional speaker-microphone.

NOTE: Above functions depend on pre-setting.

Red

Upper

Lower

Mic Up*

Mic Down*

Mic A*

Mic B*

DD

Programmable key reference ([Red] depends on version.)

*These functions are available when the optional Speaker/Mic. is con-

nected.

‘‘

LED indicator

The TX/RX indicator LED indicates several
more information as follows;
(Ref.; R=Red, G=Green, O=Orange)

PANEL DESCRIPTION

1

3

R R R R

R R

O O

O O

R R R R

R R

G

G G

R

• TX: Turns Red while transmitting a signal.

• RX: Turns Green while receiving a signal.

• Call LED (ON): When receiving a matched 2/5TONE.

• Call LED (Blink): When receiving a matched 2/5TONE.

• Fast/Slow scan: Blinks while Fast/Slow scan is activated.

•Low BATT1: You should charge the battery. (blinks slowly)

•Low BATT2: You must charge the battery. (blinks fast)

•TX low BATT1: Low BATT1 was detected during TX mode.

•TX low BATT2: Low BATT2 was detected during TX mode.

2

ACCESSORIES

4

‘‘

Accessory attachment

D Supplied accessories

The transceiver comes supplied with the following accessories.

q Flexible antenna
w Belt clip

D Antenna

The antenna screws onto the transceiver as
illustrated right.

D Belt clip

Attach the belt clip to the transceiver as illustrated below.

q

w

5

3

BATTERY PACKS

‘‘

Battery pack replacement

Before replacing the battery pack, the volume control MUST be ro­tated fully counterclockwise,
until a click is heard, to turn the
power OFF.

• Push the battery release for­ward, then pull the battery
pack upward with the trans­ceiver facing you.

DD

BATTERY PACKS

*1Operating periods are calculated under the following conditions;

Tx : Rx : standby =5 : 5 : 90
*1Operating period depends on the alkaline cells used. (BP-208 only)
*2Output power is automatically reduced to 1 W to retain sufficient power

in case of an emergency, etc.

*3Operating period measured with the 2 W model.

yrettaB

kcap

egatloV yticapaC

doirepgnigrahC

gnitarepO

*doirep

1

BC-146

BP-208*

2

AArofesacyretta

B

)6R( × enilakla6

902-PB V2.7srh21srh5.1srh8

012-PB V2.7

0561

hAm

18.5 hrs srh0.2srh11

1100

mAh

BP-222*

3

V2.7

006

hAm

rh1

hrs

5.5*

3

6.5 hrs

BC-144,

BC-119 or

BC-121

6

3

BATTERY PACKS

‘‘

Battery cautions

• CAUTION! NEVER short the terminals of the battery pack (or
charging terminals of the transceiver). Also, current may flow into
nearby metal objects such as a necklace, so be careful when plac­ing battery packs (or the transceiver) in handbags, etc.

Simply carrying with or placing near metal objects such as a neck­lace, etc. causes shorting. This will damage not only the battery
pack, but also the transceiver.

• NEVER incinerate used battery packs. Internal battery gas may

cause an explosion.

• NEVER immerse the battery pack in water. If the battery pack be-

comes wet, be sure to wipe it dry BEFORE attaching it to the
transceiver.

• Clean the battery terminals to avoid rust or miss contact.

• Keep battery contacts clean. It’s a good idea to clean battery ter-

minals once a week.

If your battery pack seems to have no capacity even after being
charged, completely discharge them, then fully charge the battery
pack again. If the battery pack still does not retain a charge (or only
very little charge), a new battery pack must be purchased.

DD

Recycling information (U.S.A. only)

The battery (BP-209, BP-210 or BP-222) that you
have purchased is recyclable. At the end of its life,
under various state and local laws, it may be illegal
to dispose of this battery into the municipal waste
stream. Call 1-800-822-8837 for battery recycling
options in your area or contact your dealer.

7

3

BATTERY PACKS

‘‘

Battery charging

D Rapid charging with the BC-144+AD-99

The optional BC-144 provides rapid charging of optional battery
packs.
The following are additionally required:

• One AD-99 (depends on version.).

• An AC adapter (may be supplied with the BC-144 depending on

version).

AC adapter
BC-145A/E/V/UK

BP-209, BP-210

or BP-222 only

Charging indicator

Check orientation.

8

3

BATTERY PACKS

D Rapid charging with the BC-144+AD-99

DD

Spacer combination.

• Be sure to attach the

spacer (Spacer B/C) to
the adapter (Spacer A)
with the orientation as il­lustrated in the diagram at
right.

• Attach the spacer

(Spacer B/C) to the
adapter with the orientation of the stamp “” pointing up.

NOTE: Push the notch carefully
when remove the spacer from the
adapter.

Turn power OFF

BP-209, BP-210

or BP-222 attached

to the transceiver.

AC adaptor
BC-145A/E/V/UK

Charging indicator

Check orientation

and

Spacer A

Spacer B/C

Check orientation
and the spacer com­bination as follows.

9

3

BATTERY PACKS

D Rapid charging with the BC-121+AD-94 (#11)

The optional BC-121 allows up to 6 battery packs to be charged si­multaneously. The following are additionally required.

• Six AD-94 (#11) (Some versions require additional AD-99s).

• An AC adapter (may be supplied with the BC-121 depending on

version).

D Regular charging with the BC-146

The optional BC-146 pro­vides regular charging of
optional battery pack with/
without transceiver.
The following is additionally
required:

• An optional AC adapter.

(A charging spacer is sup­plied with BC-146.)

MULTI-CHARGER

AC adaptor
(purchased
separately)

Charge indicator
(each indicator functions independently)

Turn power OFF.

AD-99

Check orientation
for correct charg­ing.

(Insert togeth­er with charging
adapter.)

Turn power OFF.

BC-146

10

3

BATTERY PACKS

‘‘

Charging NOTE

Prior to using the transceiver for the first time, the battery pack must
be fully charged for optimum life and operation.

• Recommended temperature range for charging:
+10°C to +40°C (50°F to 140°F).

• Use the supplied charger or optional charger (BC-119/BC-121/BC­144 for rapid charging, BC-146 for regular charging) only. NEVER
use other manufacturers’ chargers.

The optional BP-209, BP-210 or BP-222 battery packs include
rechargeable Ni-Cd(Ni-MH: BP-210) batteries and can be charged
approx. 300 times. Charge the battery pack before first operating
the transceiver or when the battery pack becomes exhausted.
If you want to charge the battery pack more than 300 times, the fol­lowing points should be observed:

• Avoid overcharging–batteries must be removed from the charger
to stop charging. Batteries should not be charged for more than
15 hours after the LED indicator turns green.

• Use the battery until it becomes almost completely exhausted
under normal conditions.

DD

Battery pack life

When the operating period becomes extremely short even after
charging the battery pack fully, a new battery pack is needed.

NOTE: The charger rapidly charges a battery pack to a speci­fied level, not a completed level, to prevent overcharging. Leave
the battery pack in the charger for a few more hours (up to
15 hours; depending on battery condition) after the LED indica­tor turns green, to charge the battery completely.

‘‘

Battery case (Option)

When using a BP-208 OPTIONAL BATTERY CASE attached to the
transceiver, install 6 AA (R6) size alkaline batteries as illustrated
below.

NOTE: Output power is automatically reduced to 1 W to retain suffi-

cient power in case of an emergency, etc.

DD

CAUTIONS

• Use ALKALINE batteries only.

• Make sure all battery cells are the same brand, type and ca-

pacity.

• Never mix old and new batteries.
Either of the above may cause a fire hazard or damage the
transceiver, if ignored.

• Never incinerate used battery cells since internal battery gas

may cause them to rupture.

• Never expose a detached battery case to water.
If the battery case gets wet, be sure to wipe it dry before using
it.

11

3

BATTERY PACKS

12

4

PROGRAMMABLE FUNCTIONS

‘‘

General

In the following explanations, programmable function names are
bracketed, the specific switch used to activate the function depends
on programming.

DD

KEY LOCK FUNCTION1/2

This function locks access to all programmable switches (except
the switch assigned for the lock function):
Lock1: All Key Lock function; lockes all keys except Lock, PTT,

CALL, Moni, Emergency keys and Channel selector
SW.

Lock2: Channel selector SW Lock function; lockes all keys ex-

cept Lock, PTT, CALL, Moni and Emergency keys.

Push and hold the [Lock1] or [Lock2] switch for 1 sec. to toggle the
lock function ON and OFF.

• This function may be inhibited on some channels.

DD

PRIORITY CHANNEL

This function is used to select a pre-programmed channel at the
push of a switch.
Push the [PrioA], [PrioA(Rewrite)] or [PrioB] switch to select the pri­ority channel.

• Priority channel is automatically selected.

13

4

PROGRAMMABLE FUNCTIONS

DD

SCAN FUNCTION

The scan function allows you to search a pre-programmed group
of channels for signals.

Push the [Scan] switch to start/stop scan.

• Scan pauses on a channel when receiving a signal.

• “Lockout SCAN” (pre-programmed list SCAN) or “Priority SCAN”

can be pre-programmed.

• When the “Power-save function” is activated, the transceiver
checks all pre-programmed channels then returns to the “Power­save function” again.

DD

HIGH/LOW POWER OUTPUT

This function selects high or low power for a channel.

Push the [High/Low] switch to toggle between high and low power.

4

PROGRAMMABLE FUNCTIONS

14

DD

MONITOR AUDIBLE FUNCTION

The monitor function allows you to open the transceiver’s squelch
manually to check whether a channel is busy or not. The trans­ceiver has 2 conditions for receive standby:

Audible condition:

This condition mutes audio ONLY when
no carrier is present. You can receive (or
monitor) any signals on a channel.

• Push and hold the [Moni], switch to se­lect the audible condition.

Any audio mute functions are cancelled
while pushing the [Moni] switch.

Inaudible condition:

This condition mutes ALL signals except
those directed to you. Therefore you
should check a channel’s condition (busy
or not) with the monitor function before
transmitting.

• Push the [Moni] switch momentarily to

select the inaudible condition.

DD

TALK AROUND

The talk around function changes duplex channels to simplex chan­nels.

• Duplex allows you to contact your base station, repeaters, etc.

• Simplex allows you to contact other portable transceivers directly

(portable-to-portable contact).

Push the [Talk Around] switch one or more times to toggle the func­tion ON and OFF.

All signals are
received

Only signals con­taining the proper
tone are received

PROGRAMMABLE FUNCTIONS

15

2

DD

DTMF TRANSMISSION

This function allows you to send a pre-programmed DTMF code to
control a repeater, open another transceiver’s squelch, etc.

Automatic pre-programmed transmission:
Push the [DTMF Autodial] switch to send a DTMF code.

DD

EMERGENCY FUNCTION

The emergency function allows you to send your ID quickly and
easily to your Base Station, etc. in case of emergency.

Push and hold the [Emergency Single/repeat] switch for 1 sec. to
activate the emergency function.

• The transceiver selects a pre-programmed channel, then sends
an emergency signal to your Base Station.

• The pre-programmed channel remains selected until a control sig­nal is received from the Base Station, or power is turned OFF.

• The emergency call is repeatedly transmitted at pre-programmed
intervals.

DD

MR-CH1, MR-CH2, MR-CH3, MR-CH4

This function temporarily allows you to select one of memory CH1
to CH4, when you push the [MR-CH1–4] key.

4

PROGRAMMABLE FUNCTIONS

16

DD

CODE SQUELCH

This conveniently eliminates unwanted audio and is useful in group
activities or security related activities where unwanted output can
be a problem. The function is similar to a CTCSS tone squelch.

In order to use the above functions, cloning is necessary via a PC
using the optional CS-F11 cloning software. Using this software, the
transceiver’s model, individual RX Code CH, TX Code CH, Special
Tone Link2 (must be ‘E’) in 5Tone screen, 5Tone Signaling Form in
Memory-CH screen, Log, RX C-No, Key&Display, Common Au­toReset TimerB, and other settings related to operation can be set.
Refer to the HELP file that comes with the CS-F11

CLONING SOFT-

WARE for available settings.

17

5

CONVENTIONAL OPERATION

‘‘

Receiving and transmitting

NOTE: Transmitting without an antenna may damage the trans-

ceiver. See p.4 for antenna attachment.
Turn power ON as described on p. 2.

Receiving:

q Select a desired channel.
w Listen for a transmission and adjust [VOL] to a comfortable lis-

tening level.

• When no transmission is heard, push and hold [Moni] (moni­tor) while adjusting [VOL] (your transceiver may not be pro­grammed with the monitor function).

The transceiver is now set to receive desired calls on the selected
channel.

Transmitting:

Wait for the channel to become clear to avoid interference.
e While pushing and holding [PTT], speak into the microphone at a

normal voice level.

• When a tone signalling system is used, the call procedure de­scribed at right may be necessary.

r Release [PTT] to return to receive.

IMPORTANT: To maximize the readability of your transmitted sig­nal, pause a few sec. after pushing [PTT], hold the microphone 10
to 15 cm from your mouth and speak at a normal voice level.

18

5

CONVENTIONAL OPERATION

‘‘

Call procedure

When your system employs tone signalling (excluding CTCSS and
DTCS), the call procedure may be necessary prior to voice trans­mission. The tone signalling employed may be a selective calling
system which allows you to call specific station(s) only and prevent
unwanted stations from contacting you.

q Select the desired Tx code channel or 5-tone code according to

your System Operator’s instructions.

• This may not be necessary depending on programming.

w Push the call switch (assigned to one of the dealer programma-

ble switches: [Upper] and [Lower], etc.).

e After transmitting a 5-tone code, the remainder of your commu-

nication can be carried out in the normal fashion.



Non-selective calling

Selective calling

CONVENTIONAL OPERATION

19

5

‘‘

Setting squelch level

The squelch circuit mutes the received audio signal depending on
the signal strength.

q While pushing [PTT] and [Lower],

turn the transceiver’s power on to
enter the squelch adjustment
mode.

w Push [Upper] to increase the

squelch level (tight squelch) or
[Lower] to decrease the squelch
level (loose squelch).

• Squelch level will be fixed after

1 sec.

‘‘

Transmitting notes

DD

TIME-OUT TIMER

After continuous transmission for a pre-programmed period, the
time-out timer is activated causing the transceiver to stop transmit­ting, and automatically select receive.

DD

PENALTY TIMER

Once the time-out timer is activated, transmission is further inhibited
for a period determined by the penalty timer.

[Upper]

[PTT]

[Lower]

20

6

CLONING

‘‘

Cloning

Cloning allows you to quickly and easily transfer the programmed
contents from one transceiver to another transceiver; or data from
PC to a transceiver using the optional CS-F11

CLONING SOFT-

WARE.

DD

Transceiver-to-transceiver cloning

NOTE:

‘

Transceiver-to-transceiver cloning’ is available be­tween the same models on 2CH model to 16CH model or the
opposite case cannot be cloned.

q Connect the optional OPC-474 CLONING CABLE with adapter

plugs to the [SP] jack of the master and slave transceivers.

• The master transceiver is used to send data to the slave trans­ceiver.

w While pushing [PTT] and [Upper], turn the transceiver’s power

on to enter cloning mode (master transceiver only–power ON
only for slave transceiver).

e Push [PTT] on the master transceiver.

NOTE: DO NOT push the [PTT] on the slave transceiver during
cloning. This will cause a cloning error.

r When cloning is finished, turn power off, then on again to return

to normal operation.

DD

PC-to-transceiver cloning

Please refer to the HELP file that comes with the CS-F11 CLONING
SOFTWARE.

CAUTION: Imprudent cloning operation causes a cloning error.
In such a case, memory contents may be lost. Cloning must
then be repeated.

21

7

OPTION

‘‘

Options

DD

BATTERY PACKS

• BP-208 BATTERY CASE
Allows a set of Alkaline batteries to operate the handheld when
charging the rechargeable battery or in emergencies, etc. 6 AA
(R6) cells are required.

• BP-209 Ni-Cd BATTERY PACK

7.2 V/1100 mAh Ni-Cd battery pack, allows more than 8 hours op­eration.

• BP-210 Ni-MH BATTERY PACK

7.2 V/1650 mAh Ni-MH battery pack, allows approx. 11 hours op­eration.

• BP-222 Ni-Cd BATTERY PACK

7.2 V/600 mAh Ni-Cd battery pack, allows approx. 5.5* hours op­eration (Same as supplied with 2 W models).
*When used with 2 W model.

DD

CHARGER

• BC-119 DESKTOP CHARGER + AD-94 (#11)

For rapid charging of battery packs. An AC adapter is supplied
with the charger. Charging time: 1.5 to 2 hrs.

• BC-121 MULTI-CHARGER

For rapid charging up to 6 battery packs simultaneously. An AC
adapter may be supplied depending on version. Six AD-94 (#11)’s
are necessary. Charging time: 1.5 to 2 hrs.

• AD-99 CHARGER ADAPTOR

• BC-144 DESKTOP CHARGER

For rapid charging of BP-209 (Ni-Cd), BP-210 (Ni-MH) and BP­222 (Ni-Cd).

• BC-146 DESKTOP CHARGER
For regular charging of BP-209 (Ni-Cd), BP-210 (Ni-MH) and BP­222 (Ni-Cd).

22

7

OPTION

DD

OTHER OPTIONS

• HM-46L/HM-75A/HM-131L SPEAKER-MICROPHONES
Combination speaker-microphone that provides convenient oper­ation while hanging the transceiver from your belt.
HM-75A has programmable function key Mic Up, Mic Down, Mic
A, Mic B.
HM-131L has a moisture proof construction.

• HS-51 HEAD SET
Allows you hands-free operation. Includes PTT and TOT.

• SP-13 EARPHONE
Provides clear receive audio in noisy environments.

• MB-68 BELT CLIP
Same as that supplied with the transceiver.

• MB-74 BELT CLIP
Exclusive alligator-type belt clip.

• AD-98FSC ANTENNA CONNECTOR ADAPTER
Allows you to connect a BNC-type antenna.

• CS-F11 CLONING SOFTWARE
Allows you to clone the memory contents of an IC-F11/S, IC­F21/S by PC editing.

• OPC-474 CLONING CABLE
Cloning cable for transceiver to transceiver

• OPC-478 CLONING CABLE
Cloning cable for PC to transceiver.

23

8

CE

CE Versions of the IC-F12/S, F22/S which display the
“CE” symbol on the serial number seal, comply with
the essential requirements of the European Radio and
Telecommunication Terminal Directive 1999/5/EC.

ABOUT CE

This warning symbol indicates that this equipment op­erates in non-harmonised frequency bands and/or
may be subject to licensing conditions in the country
of use. Be sure to check that you have the correct
version of this radio or the correct programming of this
radio, to comply with national licensing requirement.

• When transmitting with a portable radio, hold the radio in a vertical po­sition with its microphone 2.5 to 5 centimeters away from your mouth.
Keep antenna at least 2.5 centimeters from your head and body.

• If you wear a portable two-way radio on your body, ensure that the an­tenna is at least 2.5 centimeters from your body when transmitting.

INSTALLATION NOTES

24

2

CE

DECLARATION

OF CONFORMITY

We Icom Inc. Japan

1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan

Kind of equipment:

UHF TRANSCEIVER

This compliance is based on conformity with the following harmonised
standards, specifications or documents:

i) EN300 279 v1.2.1(1999-02) (EMC product standard)
ii) EN60950 August 1992, A11 1997 (Safety of information technology equipment)
iii) ETS300 086 January 1991 (Radio equipment for analog speech)
iv) ETSI EN300 219 v1.2.1 (1999-10) (Radio equipment transmitting signals)
v)

Type-designation: iC- f22/s

Signature

Authorized representative name

Place and date of issue

T. Aoki
General Manager

Icom (Europe) GmbH

Himmelgeister straße 100
D-40225 Düsseldorf

Düsseldorf 25 Dec. 2000

Icom (Europe) GmbH

Declare on our sole responsibility that this equipment complies the
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Suite measurements have been performed.

Version (where applicable):

0168

440-470 MHz 12.5 KHz/ 25 KHz

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan

A-6024H-1EU
Printed in Japan
© 2001 Icom Inc.

Count on us!

IC-F12/F22S series

o

GER

o

AUT

o

GBR

o

IRL

o

FRA

o

NED

o

BEL

o

LUX

o

ESP

o

POR

o

ITA

o

GRE

o

SWE

o

DEN

o

FIN

< Intended Country of Use >