Hyundai P230E User Manual
HYUNDAI PCS CELLULAR PHONE
P230E
USER’S MANUAL
HYUNDAI ELECTRONICS INDUSTRIES., Ltd.
Mobile Telecommunications Division
1
Chapter 1
Prior to Use
➀ Names and function of each part
➁ Screen status display and function
2
Role of the function buttons
[TALK] This button is used when you make a call or receive a call.
.
[END] This button is used when you terminate a call or exit the current menu in the menu
[RCL] This button is used when you look up the list of stored phone numbers or names or
the phone number you just called.
[CLR] This button is used to clear the digits and/or text from the display or Memory.
[STO] This button is used to go to a lower level menu or to store the set parameter; put
phone number and names into memory or erase those that were input.
[*][# ] These buttons are scroll buttons which you use to select screen contents.
[PWR] This button is used to turn the handset on or off
[MENU] This button is used to select menu.
This button is used to select SMS service .
.
3
Screen status display and function
Signal strength
The strength of current signal is displayed with the number (0-5) of bar.
Roaming
This icon shows the user is outside the normal service area .
Service possible/impossible
When you are in an area where service possible, displayed.
When you are in an area where service is impossible, is displayed. Also when you are in
service, “in service icon” is displayed.
Voice or Character message service
Blinks when character or voice messages have been received.
Alarm
Blinks when alarm was played if user set alarm.
Balance of battery power
The balance of battery power available is displayed with the number (0~4) of bar.
4
Chapter 2
Basic operation
➀➀➀➀ Menu structures
➁ How to use menu function
➂ How to use handset
➃ Function in the call
5
MENU STRUCTURE
●
Menu Submenu
1: BILLING
2: SETTING
3: DISPLAY
4: VOLUME
5: CALL TIMER
1: AUTO RETRY
2: AUTO ANSWER
3: AUTO HYPHEN
4: DTMF LENGTH
5: ONE TOUCH
1: DSPLY TIME
2: BANNER
3: LCD CONTST
4 :BACK LIGHT 1: AUTO LIGHT
1: RING TYPE
2: RINGER
3: EARPIECE
4: KEYPAD VOL
5: HANDSFREE
6: CONNECT V.
7: MY MELODY
1: CALL TIME
2: ALARM
1: INTERVAL
2: REPEAT
1: SHORT
2: LONG
2: LENGTH
LED
LED+BACKLIGHT
VIBRATOR
SILENT
VOLUME
1: EDIT
2: LISTEN
1: LAST CALL
2: ALL CALLS
3: HOME CALLS
4: ROAM CALLS
1: ACTIVATE
2: ALARM ONLY
3: ALARM CALL
6
Menu Submenu
6: BIO RHYTHM
7: ALERTS
8: PHONE INFO
9: SECURITY
1: TODAY BIO
2: SOMEDAY BIO
3: BIRTHDAY
1: MIN ALERT
2: FADE ALERT
3: ROAM ALERT
4: LOW SIGNAL
1: PHONE #
2: PHONE VERSION
3: EVRC MODE
1: LOCK
1: AUTO LOCK
2: CHANGE CODE.
2: RESTRICT
3: RESET
4: CLEAR
1: INCOMING
2: OUTGOING
3: DIAL #
4: MEMORY ONLY
5: LONG DIST
6: 900#
1: STORED #S
2: ALARM
3: HOME CALLS
4: ROAM CALLS
7
Menu
RECALL MENU
MENU IN CALLS
DIAL MEN U
( DIAL BUTTON + [MENU]
BUTTON)
DIAL MENU IN CALLS
1: PHONE BOOK
2: CALL LOGS
1: SEND PHONE #
2: SCRATCH PAD
3: MUTE
1:HARD PAUSE
2:TIME PAUSE
3:ONE HYPHEN
1:SEND PHONE #
2:HART PAUSE
3:TIME PAUSE
4:ONE HYPHEN
8
How to use Menu function
♣
Please read this before you use your handset
1. In a standby screen, press [MENU] button.
2. To move around the menu, use scroll buttons.
If you press the scroll button continuously, the menu
passes by automatically.
.
Scroll buttons: [*▲],[#▼],volume[+],volume[-]
3. To go back to previous screen, press [CLR] button.
To exit menu screen, press
4. To go to a lower menu, press appropriate number, or select
desired item by scroll button, and then press
[END] button.
[STO]button.
If there is lower menu, the lower menu will be
newly displayed.
5. [SMS],[RCL],[SEND] buttons can be used while using menu
function
9
How to use handset
How to turn the handset on
Press [PWR]button until the lamp turn on
•
!
Handset is in locking status if “Lock code”
is displayed on the screen.
When the lock code is displaying, enter a 4-digit
lock release number to unlock the handset.
then use.
!
The default value of lock code is “0000”..
!
If there is a lot of stored information, it
takes
How to turn the handset off
Press [PWR]button until the lamp turn on
•
!
“REGISTERING...” message is displayed when the user presses PWR button.
This message indicates that the handset is registering the power off
information, and that
means mobile telecommunications service system does not have to search the
user.
!!!!
If the “LOW BATTERY WARNING POWER OFF” message is displayed and the
power goes off,
there is a possibility of damaging the memory. Therefore, in that
case, do not turn the power on, and change or charge the battery
immediately.
!!!!
When the power goes off when the battery is separated while it was
power on status,
the calling time, phone number previous call, and frequently used area
code might not get stored properly.
10
How to call
1 Press area code + phone number in order
How to modify a phone number you have entered:
number by number modification:
"
Press [CLR] button.
Whole number modification:
"
Press [CLR] button and hold
more than
0.5 second.
•
•
Press any button to go back to standby status
[TALK].
Press
! "CALL FAILED” message is displayed when the call is not connected.
! When the line is busy, press (END) button, and retry [TALK] button.
!
If you select AUTO RETRY function, the call will be repeated
automatically .
!
It is convenient to connect the call after hearing system connection
signal
sounding “beep, beep, beep” .
press [END]button when end the call
! The number of calling minutes blinks for 3 seconds.
Depending on the network the user is using, there can be e
differences
but it is not related to actual service charge the user has to pay.
Note
To go back to previous call number, press
If the sign shows up on the screen, the call cannot be
[TALK] button.
connected,
and the user should get out of the current area.
.
11
Phone number input method
To call convention phone : area code + phone number+ [TALK]
!
To call emergency numbers : emergency number
!
( 911,311,*911,#911,#311)+ [TALK]
To call other cellular phone : area code + phone number+ [TALK]
!
To call international number: international call identification number + country code +
!
phone number + [TALK]
To call wireless beeper:wireless beeper identification number + beeper number+ [TALK]
!
Electronic dialing function using pause character
Electronic dialing function to use ARS service provided by
banks, etc,
and auto beep function.
1. Enter phone number, and press
[MENU]
####
[1] or [2].
0154834326P
2. Press numbers to be electronically dialed.
26P1T023449000
3. Press [TALK] button.
" $ HARD PAUSE : Enter the pause character (P) after the phone
number and
press [TALK]number to send phone number entered after the
pause character.
01548343
12
" % TIME PAUSE : If you enter the pause character (T), the phone
number
entered after the pause character will be send out
automatically in three
1
Any button except [PWR] button when
seconds.
phone bell rings or lamp blinks.
To end the call, press [END] button.
•
How to answer calls
Note
!
If you set AUTO ANSWER function in advance, the call will be connected after
the designated number of bell rings. (Refer to P )
Sender number display function
PCS service provider supports sender number display
function.
The service will be available after subscribing to the
service.
13
When there is an incoming call, the sender’s phone number is
displayed on the screen as following.
Caller ID :
02 - 3 4 4 9 - 0 0 0 0
Missing message display function
Displays calls that the user didn’t answered.
Displays the number of missed calls and latest calling
①
time.
①Adjust volume by pressing the volume button during the state of operation of the
handset as below:
Call status: Ear piece volume adjustment
"
Standby status: Beep volume adjustment
"
"
"
When bell rings: Ringer volume adjustme nt
MISSED
XX CALLS
Call status in hands-free : hands-free volume adjustment
18 : 25
& If the user subscribes sender number display function service, senders
numbers will be
displayed on the screen. And the call will be stored in the previous call
& The message will be cleared when the user presses [CLR]/[END] button.
How to adjust volume
Volume adjusting can be done in two ways: by using the volume button on the side of the receiver,
or by using the buinon menu
’
14
After adjusting the volume, store using [STO] button.
➁
The volume level is stored automatically2 seconds
"
after adjusting the volume.
15
Loading...