Husqvarna 335LX User Manual
Oper ator’s manual (EPA)
335LS 335L
Please r ead the operator’s manual carefully and make sure you understand the instructions
X-series
before using the machine.
EEEEnnnngggglllliiiisssshh
hh
2
W
KEY T O SYMBOLS
Symbols
ARNING! Clearing saws,
brushcutters and trimmers can be
dangerous! Careless or incorrect use
can result in serious or fatal injury to
the operator or others.
Please read the operator’s manual
carefully and make sure you
understand the instructions before
using the machine.
Always wear:
• A protective helmet where there is
a risk of falling objects
• Approved hearing protection
• Approved eye protection
Max. speed of output shaft, rpm
Watch out for thrown objects and
ricochets.
The operator of the machine must
ensure, while working, that no persons
or animals come closer than 15 metres.
Machines fitted with saw blades or
grass blades can be thrown violently to
the side when the blade comes into
contact with a fixed object. The blade is
capable of amputating an arm or leg.
Always keep people and animals at
least 15 metres from the machine.
Arrows which show limits for handle
positioning.
Always wear approved protective gloves.
Only use non-metallic, flexible cutting
attachments, i.e. trimmer heads with
trimmer cord.
Starting instructions
1.
2.
3.
4.
Other symbols/decals on the
machine refer to special certification
requirements for certain markets.
The engine is s witched off by moving
the stop switch to the stop position.
CAUTION! The stop switch
automatically returns to the start
position. In order to prevent
1
5
m
5
1
5
0
F
50FT
unintentional starting, the spark plug
m
T
cap must be removed from the spark plug when assembling,
checking and/or performing maintenance.
Always wear approved protective
gloves.
Regular cleaning is required.
Visual check.
Wear sturdy, non-slip boots.
– English
Approved eye protection must always
be used.
!
!
!
ST
W
T
Y
W
W
W
CONTENTS
Contents
KEY TO SYMBOLS
Symbols .................................................................... 2
CONTENTS
Contents .................................................................... 3
Note the following before starting: ............................. 3
INTR ODUCTION
Dear customer! .......................................................... 4
WHA T IS WHAT?
What is what on the clear ing saw? ............................ 5
GENERAL SAFETY PRECA UTIONS
Impor tant ................................................................... 6
Personal protective equipment .................................. 6
Machine ′ s safety equipment ...................................... 7
Cutting equipment ..................................................... 10
ASSEMBL Y
Fitting the loop handle ............................................... 11
Assembling the cutting equipment ............................ 11
FUEL HANDLING
Fuel saf ety ................................................................. 12
Fuel ........................................................................... 12
Fueling ...................................................................... 13
ARTING AND STOPPING
Chec k before starting ................................................ 14
Starting and stopping ................................................ 14
ORKING TECHNIQUES
Gener al working instructions ..................................... 16
MAINTENANCE
Carb uretor ................................................................. 18
Muffler ....................................................................... 19
Cooling system .......................................................... 20
Bevel gear ................................................................. 20
Air filter ...................................................................... 20
Spark plug ................................................................. 21
Maintenance schedule .............................................. 22
TECHNICAL D ATA
echnical data ........................................................... 23
FEDERAL AND CALIFORNIA EMISSIONS
CONTROL WARRANTY STATEMENT
OUR WARRANTY RIGHTS AND OBLIGATIONS ... 24
Note the f ollowing before starting:
Please read the oper ator’s manual carefully.
Maintenance, replacement, or repair of the emission control
devices and system may be performed by any nonroad
engine repair establishment or individual.
ARNING! Long-term exposure to noise
can result in permanent hearing
impairment. So always use approved
hearing protection.
ARNING! Under no circumstances may
the design of the machine be modified
without the permission of the manufacturer.
Always use genuine accessories. Nonauthorized modifications and/or
accessories can result in serious personal
injury or the death of the operator or others.
Your warranty may not cover damage or
liability caused by the use of nonauthorized accessories or replacement
parts.
ARNING! A clearing saw, brushcutter or
trimmer can be dangerous if used
incorrectly or carelessly, and can cause
serious or fatal injury to the operator or
others. It is extremely important that you
read and understand the contents of this
operator’s manual.
The Emissions Compliance Period referred to on the
emissions compliance label indicates the number of
operating hours for which the engine has shown to meet
Federal and Californian emission requirements.
The engine exhaust from this product
contains chemical known to the State
of California to cause cancer, birth
defects or other reproductive harm.
English
–
3
4
′
′
INTR ODUCTION
Dear customer!
Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when
the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets.
The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.
During over 300 years of continuous operation, the Husqvarna factory has produced a lot of different products, from wood
stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the first motor driven lawn mowers
appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our highest
priority. We develop, manufacture and market high quality motor driven products for forestry and gardening as well as for
building and construction industry.
Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the retailer
who sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this
operator
s manual as a valuable document. By following its ′ content (using, service, maintenance etc) the life span and the
second-hand value of the machine can be extended. If you ever lend or sell this machine, make sure that the borrower or buyer
gets the operator
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and
appearance of products without prior notice.
For customer assistance, contact us at our website: www.usa.husqvarna.com
s manual, so they will also know how to properly maintain and use it.
– English
WHA T IS WHA T?
1
24
What is what on the c learing saw?
Trimmer head
2 Grease filler cap, bevel gear
3 Bevel gear
4 Cutting attachment guard
5 Shaft
6 Handle adjustment
7 Loop handle
8 Suspension ring
9 Stop switch
10 Throttle lockout
11 Throttle control
12 Spark plug cap and spark plug
20
23
13 Cylinder cover
14 Starter handle
15 Fuel tank
16 Choke control
17 Air filter cover
18 Air purge
19 Operator’s manual
20 Harness
21 Allen key
22 Drive disc
23 Locking pin
24 Spark plug spanner
English – 5
!
6
W
W
W
W
GENERAL SAFETY PRECA UTIONS
Impor tant Personal protective equipment
IMPORTANT!
The machine is only designed for trimming grass.
The only accessories you can operate with this engine unit
are the cutting attachments we recommend in the chapter
on Technical data.
Never use the machine if you are tired, if you have drunk
alcohol, or if you are taking medication that could affect
your vision, your judgement or your co-ordination.
Wear personal protective equipment. See instructions
under the heading Personal protective equipment.
Never use a machine that has been modified in any way
from its original specification.
Never use a machine that is faulty. Carry out the checks,
maintenance and service instructions described in this
manual. Some maintenance and service measures must
be carried out by trained and qualified specialists. See
instructions under the heading Maintenance.
All covers, guards and handles must be fitted before
starting. Ensure that the spark plug cap and ignition lead
are undamaged to avoid the risk of electric shock.
The machine operator must ensure that no people or
animals come closer than 15 metres while working. When
several operators are working in the same area the safety
distance should be at least twice the tree height and no
less than 15 metres.
ARNING! The ignition system of this
machine produces an electromagnetic field
!
during operation. This field may under
some circumstances interfere with
pacemakers. To reduce the risk of serious
or fatal injury, we recommend persons with
pacemakers to consult their physician and
the pacemaker manufacturer before
operating this machine.
ARNING! Running an engine in a confined
or badly ventilated area can result in death
!
due to asphyxiation or carbon monoxide
poisoning.
IMPOR TANT!
A clearing saw, brushcutter or trimmer can be dangerous if
used incorrectly or carelessly, and can cause serious or
fatal injury to the operator or others. It is extremely
important that you read and understand the contents of this
operator’s manual.
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen.
Ask your dealer for help in choosing the right equipment.
ARNING! Listen out for warning signals
or shouts when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.
HELMET
A protectiv e helmet where there is a risk of falling objects
HEARING PROTECTION
Wear hearing protection that provides adequate noise
reduction.
EYE PROTECTION
Always wear approved eye protection. If you use a visor then
you must also wear approved protective goggles. Approved
protective goggles must comply with standard ANSI Z87.1 in
the USA or EN 166 in EU countries.
– English
ARNING! Never allow children to use or
be in the vicinity of the machine. As the
!
machine is equipped with a spring-loaded
stop switch and can be started by low
speed and force on the starter handle, even
small children under some circumstances
can produce the force necessary to start
the machine. This can mean a risk of
serious personal injury. Therefore remove
the spark plug cap when the machine is not
under close supervision.
GLOVES
Gloves should be worn when necessary, e.g., when fitting
cutting attachments.
GENERAL SAFETY PRECA UTIONS
7
′
W
BOO TS
Wear sturdy, non-slip boots.
CLOTHING
Wear clothes made of a strong fabric and avoid loose
clothing that can catch on twigs and branches. Always wear
heavy, long pants. Do not wear jewellery, shorts sandals or
go barefoot. Secure hair so it is above shoulder level.
FIRST AID KIT
Always have a first aid kit nearby.
Mac hine ′ s safety equipment
This section descr ibes the machine ′ s safety equipment, its
purpose, and how checks and maintenance should be
carried out to ensure that it operates correctly. See the ”What
is what?” section to locate where this equipment is
positioned on your machine.
IMPORTANT! All servicing and repair work on the machine
requires special training. This is especially true of the
machine
s safety equipment. If your machine fails any of
the checks described below you must contact your service
agent. When you buy any of our products we guarantee the
availability of professional repairs and service. If the
retailer who sells your machine is not a servicing dealer,
ask him for the address of your nearest service agent.
return springs. This arrangement means that the throttle
control is automatically locked at the idle setting.
A
B
Make sure the throttle control is locked at the idle setting
when the throttle lockout is released.
Press the throttle lockout and make sure it returns to its
original position when you release it.
Check that the throttle control and throttle lockout move
freely and that the return springs work properly.
ARNING! Never use a machine with faulty
safety equipment. The machine’s safety
!
equipment must be checked and
maintained as described in this section. If
your machine fails any of these checks
contact your service agent to get it
repaired.
Thr ottle lockout
The throttle loc kout is designed to prevent accidental
operation of the throttle control. When you press the lock (A)
(i.e. when you grasp the handle) it releases the throttle
control (B). When you release the handle the throttle control
and the throttle lockout both move back to their original
positions. This movement is controlled by two independent
See instructions under the heading Start. Start the machine
and apply full throttle. Release the throttle and check that the
cutting attachment stops and remains at a standstill. If the
cutting attachment rotates with the throttle in the idle position
then the carburettor idle setting must be checked. See
instructions under the heading Maintenance.
English
–
GENERAL SAFETY PRECA UTIONS
!
Stop switch
Use the stop switch to switch off the engine.
Start the engine and make sure the engine stops when you
move the stop switch to the stop setting.
Cutting attachment guard
This guard is intended to prevent loose objects from being
thrown towards the operator. The guard also protects the
operator from accidental contact with the cutting attachment.
Check that the guard is undamaged and not cracked.
Replace the guard if it has been exposed to impact or is
cracked.
Always use the recommended guard for the cutting
attachment you are using. See chapter on Technical data.
WARNING! Never use a cutting attachment
without an approved guard. See the chapter
!
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
Vibration damping system
Your machine is equipped with a vibration damping system
that is designed to reduce vibration and make operation
easier.
Using incorrectly wound cord or a blunt or incorrect cutting
attachment (wrong type or incorrectly filed, see instructions
under the heading Filing the blade) increases the level of
vibration.
The machine′s vibration damping system reduces the
transfer of vibration between the engine unit/cutting
equipment and the machine
Regularly check the vibration damping units for cracks or
deformation.
Check that the vibration damping element is undamaged
and securely attached.
WARNING! Overexposure to vibration can
lead to circulatory damage or nerve
damage in people who have impaired
circulation. Contact your doctor if you
experience symptoms of overexposure to
vibration. Such symptoms include
numbness, loss of feeling, tingling,
pricking, pain, loss of strength, changes in
skin colour or condition. These symptoms
normally appear in the fingers, hands or
wrists. The risk increases at low
temperatures.
′s handle unit.
8 – English
GENERAL SAFETY PRECAUTIONS
!
!
!
!
Muffler
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user. A muffler
fitted with a catalytic converter is also designed to reduce
harmful exhaust gases.
In countries that have a warm and dry climate there is a
significant risk of fire. We therefore fit certain mufflers with a
spark arrestor screen. Check whether the muffler on your
machine is fitted with this kind of screen.
For mufflers it is very important that you follow the
instructions on checking, maintaining and servicing your
machine.
Never use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to the
machine.
If the muffler on your machine is fitted with a spark arrestor
screen this must be cleaned regularly. A blocked screen will
cause the engine to overheat and may lead to serious
damage.
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.
This also applies at idle speed. Contact can
result in burns to the skin. Remember the
risk of fire!
WARNING! The inside of the muffler contain
chemicals that may be carcinogenic. Avoid
contact with these elements in the event of
a damaged muffler.
WARNING! Bear in mind that:
The exhaust fumes from the engine are hot
and may contain sparks which can start a
fire. Never start the machine indoors or
near combustible material!
English – 9
GENERAL SAFETY PRECAUTIONS
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
• Reduce the risk of blade thrust.
• Obtain maximum cutting performance.
• Extend the life of cutting equipment.
IMPORTANT!
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
Refer to the instructions for the cutting attachment to check
the correct way to load the cord and the correct cord
diameter.
WARNING! Always stop the engine before
doing any work on the cutting attachment.
!
This continues to rotate even after the
throttle has been released. Ensure that the
cutting attachment has stopped completely
and disconnect the HT lead from the spark
plug before you start to work on it.
WARNING! A faulty cutting attachment may
increase the risk of accidents.
!
Trimmer head
IMPORTANT!
Always ensure the trimmer cord is wound tightly and evenly
around the drum, otherwise the machine will generate
harmful vibration.
• Only use the recommended trimmer heads and trimmer
cords. These have been tested by the manufacturer to
suit a particular engine size. This is especially important
when a fully automatic trimmer head is used. Only use
the recommended cutting attachment. See the chapter
on Technical data.
• Smaller machines generally require small trimmer heads
and vice versa. This is because when clearing using a
cord the engine must throw out the cord radially from the
trimmer head and overcome the resistance of the grass
being cleared.
• The length of the cord is also important. A longer cord
requires greater engine power than a shorter cord of the
same diameter.
• Make sure that the cutter on the trimmer guard is intact.
This is used to cut the cord to the correct length.
• To increase the life of the cord it can be soaked in water
for a couple of days. This will make the line tougher so
that it lasts longer.
10 – English
ASSEMBLY
Fitting the loop handle
• Clip the loop handle onto the shaft. Note that the loop
handle must be fitted between the arrows on the shaft.
• Slide the spacer into the slot in the loop handle.
• Fit the nut, knob and screw. Do not overtighten.
• Now adjust the trimmer to give a comfortable working
position. Tighten the bolt/knob.
Assembling the cutting equipment
WARNING!
!
When fitting the cutting attachment it is
extremely important that the raised section
on the drive disc/support flange engages
correctly in the centre hole of the cutting
!
attachment. If the cutting attachment is
fitted incorrectly it can result in serious
and/or fatal personal injury.
the locking pin in the groove on the screw head and
tighten. See diagram.
M
C
L
A
• Fit the drive disc (B) on the output shaft.
H
B
• Tur n the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
• Insert the locking pin (C) in the hole to lock the shaft.
• Screw on the trimmer head/plastic blades (H) in the
opposite direction to the direction of rotation.
• To dismantle, follow the instructions in the reverse order.
WARNING! Never use a cutting attachment
without an approved guard. See the chapter
!
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
• Fit the trimmer guard/combination guard (A) intended for
use with the trimmer head/plastic blades.
Hang the trimmer guard/combination guard (A) on the
two hooks on the plate holder (M). Bend the guard
around the shaft and tighten it with the bolt (L) on the
opposite side of the shaft. Use the locking pin (C). Place
English – 11
Loading...