Husqvarna 323HD60, 325HD60X, 325HD75X User Manual

Oper ator ′ s manual
323HD60 325HD60
325HD75
Please r ead the operator’s manual carefully and make sure you
understand the instructions before using the machine.
X-series X-series
EEEEnnnngggglllliiiisssshh
hh
2
W
KEY T O SYMBOLS

Symbols

ARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual.
Please read the oper ator’s manual carefully and make sure you understand the instructions before using the machine.
Always wear:
Approved hearing protection
Approved eye protection
This product is in accordance with applicable EC directives.
Always wear approved protective gloves.
The engine is s witched off by moving the stop switch to the stop position. CAUTION! The stop switch automatically returns to the start position. In order to prevent unintentional starting, the spark plug cap must be removed from the spark plug when assembling, checking and/or performing maintenance.
Always wear approved protective gloves.
Regular cleaning is required.
Visual check.
Protectiv e goggles or a visor must be worn.
Wear sturdy, non-slip boots or shoes.
Noise emission to the environment according to the European Community’s Directive. The machine’s emission is specied in chapter Technical data and on label.
Other symbols/decals on the mac hine refer to special certication requirements for certain markets.
English
ST
W
T
W
W

CONTENTS

Contents
KEY TO SYMBOLS
Symbols ....................................................................... 2
CONTENTS
Contents ...................................................................... 3
Note the following before starting: ................................ 3
INTR ODUCTION
Dear Customer , ............................................................ 4
WHA T IS WHAT?
What is what? .............................................................. 5
GENERAL SAFETY PRECA UTIONS
Impor tant ...................................................................... 6
Personal protective equipment ..................................... 6
Machine s safety equipment ........................................ 7
FUEL HANDLING
Fuel saf ety ................................................................... 10
Fuel .............................................................................. 10
Fuelling ........................................................................ 11
ARTING AND STOPPING
Chec k before starting ................................................... 12
Starting and stopping ................................................... 12
ORKING TECHNIQUES
Gener al working instructions ....................................... 14
MAINTENANCE
Carb urettor ................................................................... 16
Mufer .......................................................................... 17
Cooling system ............................................................ 18
Spark plug .................................................................... 18
Air lter ......................................................................... 18
Gear housing ............................................................... 19
Cleaning and lubrication .............................................. 19
Maintenance schedule ................................................. 20
TECHNICAL D ATA
echnical data .............................................................. 21
EC-declaration of conformity (Applies to Europe only) . 22

Note the f ollowing before starting:

Please read the oper ator’s manual carefully.
Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection.
ARNING! Under no circumstances may the
design of the machine be modied without
!
the permission of the manufacturer. Always use genuine accessories. Non-authorized modications and/or accessories can result in serious personal injury or the death of the operator or others.
ARNING! Incorrect or careless use of a
hedge trimmer can turn it into a dangerous
!
tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual.
English
3
4
INTR ODUCTION

Dear Customer ,

Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During the more than 300 years of beeing, the Husqvarna factory has produced a lot of different products, from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the rst motor driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our highest priority. The business concept is to develop, manufacture and market motor driven products for forestry and gardening as well as for building and construction industry. Husqvarna environmental protection. That is the reason why we have developed many different features to provide our products within these areas.
We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very long time to come. The purchase of one of our products gives you access to professional help with repairs and service whenever this may be necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the address of your nearest service workshop.
It is our wish that you will be satised with your product and that it will be your companion for a long time. Think of this operator s manual as a valuable document. By following its content (using, service, maintenance etc) the life span and the second-hand value of the machine can be extended. If you will sell this machine, make sure that the buyer will get the operator s manual.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice.
s aim is also to be in the front edge according to ergonomics, usability, security and
English
1
14
WHA T IS WHA T?
What is what?
Operator s manual
2 Grease ller cap, bevel gear
3 Gear housing
4 Blades
5 Blade guard
6 Front handle
7 Cylinder cover
8 Starter handle
9 Stop switch
10 Throttle lock
11 Adjustable handle
12 Throttle control
13 Lock for handle (325HD60, 325HD75)
Fuel tank
15 Fuel cap
16 Air purge
17 Choke control
18 Air lter cover.
19 Hand guard
20 Tube of grease
21 Allen key
22 Combination spanner
23 Transport guard
24 Spark plug cap and spark plug
English
5
6
W
W
W
W
GENERAL SAFETY PRECA UTIONS

Impor tant

IMPORTANT!
The machine is only designed for cutting branches and twigs.
Never use a machine that has been modied in any way from its original specication.
Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination.
Wear personal protective equipment. See instructions under the heading Personal protective equipment.
Never use the machine in extreme weather conditions such as severe cold, very hot and/or humid climates.
Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualied specialists. See instructions under the heading Maintenance.
All covers and guards must be tted before starting. Ensure that the spark plug cap and ignition lead are undamaged to avoid the risk of electric shock.
ARNING! Running an engine in a conned
or badly ventilated area can result in death
!
due to asphyxiation or carbon monoxide poisoning.
ARNING! Listen out for warning signals or
shouts when you are wearing hearing
!
protection. Always remove your hearing protection as soon as the engine stops.
HEARING PR OTECTION
Wear hearing protection that provides adequate noise reduction.
EYE PROTECTION
Always wear approved eye protection. If you use a visor then you must also wear approved protective goggles. Approved protective goggles must comply with standard ANSI Z87.1 in the USA or EN 166 in EU countries.
GLOVES
Gloves should be worn when necessary, e.g., when tting cutting attachments.
ARNING! Never allow children to use or be
in the vicinity of the machine. As the
!
machine is equipped with a spring-loaded stop switch and can be started by low speed and force on the starter handle, even small children under some circumstances can produce the force necessary to start the machine. This can mean a risk of serious personal injury. Therefore remove the spark plug cap when the machine is not under close supervision.
ARNING! Faulty blades can increase the
risk of accidents.
!

Personal protective equipment

IMPOR TANT!
Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual.
You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment.
BOOTS
Wear sturdy, non-slip boots or shoes.
CLOTHING
Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level.
FIRST AID KIT
Always have a rst aid kit nearby.
English
GENERAL SAFETY PRECA UTIONS
W
Mac hine ′′
This section descr ibes the machine s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positioned on your machine.
The life span of the machine can be reduced and the risk of accidents can increase if machine maintenance is not carried out correctly and if service and/or repairs are not carried out professionally. If you need further information please contact your nearest service workshop.
IMPORTANT!
All servicing and repair work on the machine requires special training. This is especially true of the machine safety equipment. If your machine fails any of the checks described below you must contact your service agent. When you buy any of our products we guarantee the availability of professional repairs and service. If the retailer who sells your machine is not a servicing dealer, ask him for the address of your nearest service agent.
!
′′
s safety equipment
s
ARNING! Never use a machine with faulty safety equipment. The machine’s safety equipment must be checked and maintained as described in this section. If your machine fails any of these checks contact your service agent to get it repaired.

Thr ottle lock

Press the throttle lock and make sure it returns to its original position when you release it.
Check that the throttle control and throttle lock move freely and that the return springs work properly.
See instructions under the heading Start. Start the hedge trimmer and apply full throttle. Release the throttle trigger and check that the blades stop and remain stationary. If the blades move when the throttle trigger is in the idle position then the carburettor idle setting must be adjusted. See instructions under the heading Maintenance.

Stop s witch

Use the stop s witch to switch off the engine.
The throttle loc k is designed to prevent accidental operation of the throttle control. When you press the lock (A) (i.e. when you grasp the handle) it releases the throttle control (B). When you release the handle the throttle control and the throttle lock both move back to their original positions. This movement is controlled by two independent return springs. This arrangement means that the throttle control is automatically locked at the idle setting.
Make sure the throttle control is locked at the idle setting when the throttle lock is released.
Start the engine and make sure the engine stops when you move the stop switch to the stop setting.

Hand guar d

The hand guard pre vents hands from coming into contact with the moving blades, for example, if the operator loses grip on the front handle.
Check that the hand guard is tted correctly.
Check that the hand guard is undamaged.
English
7
8
GENERAL SAFETY PRECA UTIONS

Vibration damping system

Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier.
The machines vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machines handle unit.
The engine body including the blades is suspended on the handlebar system via a four springs.
Regularly check the vibration damping units for cracks or deformation. Check that the vibration damping element is undamaged and securely attached.
WARNING! Overexposure to vibration can lead to circulatory damage or nerve damage
!
in people who have impaired circulation. Contact your doctor if you experience symptoms of overexposure to vibration. Such symptoms include numbness, loss of feeling, tingling, pricking, pain, loss of strength, changes in skin colour or condition. These symptoms normally appear in the ngers, hands or wrists. The risk increases at low temperatures.
Never use a machine that has a faulty mufer.
Regularly check that the mufer is securely attached to the machine.
If the mufer on your machine is tted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage.
WARNING! Mufers tted with catalytic converters get very hot during use and
!
remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of re!
Mufer
The mufer is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.
A mufer tted with a catalytic converter is also designed to reduce harmful exhaust gases.
In countries that have a warm and dry climate there is a signicant risk of re. We therefore fit certain mufflers with a spark arrestor mesh. Check whether the mufer on your machine is tted with this kind of mesh.
WARNING! The inside of the mufer contain chemicals that may be carcinogenic. Avoid
!
contact with these elements in the event of a damaged mufer.
WARNING! Bear in mind that:
The exhaust fumes from the engine are hot
!
and may contain sparks which can start a re. Never start the machine indoors or near combustible material!
For mufers it is very important that you follow the instructions on checking, maintaining and servicing your machine.
English
Loading...
+ 16 hidden pages