Husqvarna 124L User Manual
Operator’s Manual
Please read these instructions and make sure you understand them before using the machine.
4L
CONTENTS
Contents
CONTENTS
Contents 2........................
Note the following before starting 2....
KEY TO SYMBOLS
Symbols 3.........................
SAFETY INSTRUCTIONS
Personal protective equipment 4......
Machine’s safety equipment 4........
Cutting equipment 5.................
Checking, maintaining and servicing
the machine’s safety equipment 5.....
General safety precautions 7.........
Starting 8.........................
Fuel safety 8.......................
Transporting and storage 8...........
General working instructions 8........
Basic safety rules 8.................
Basic working techniques 9..........
KNOW YOUR TRIMMER
Know your trimmer 11................
ASSEMBLY
Fitting the loop handle 12.............
Fitting the trimmer guard and
trimmer head 12.....................
FUEL HANDLING
Fuel 13............................
Fueling 13..........................
STARTING AND STOPPING
Check before starting 14..............
Starting and stopping 14..............
MAINTENANCE
Carburetor 15.......................
Muffler 16..........................
Spark plug 16.......................
Air filter 17..........................
Bevel gear 17.......................
Maintenance schedule 17.............
Trimmer head line loading instructions 18..
TECHNICAL DATA
Technical data 19....................
WARRANTY STATEMENT 20.........
EMISSION CONTROL
WARRANTY STATEMENT 21.........
Note the following before
starting:
Husqvarna AB has a policy of continuous
product development and therefore
reserves the right to modify the design and
appearance of products without prior
notice. Long--term exposure to noise can
result in permanent hearing impairment.
Always use approved hearing protection.
Maintenance, replacement, or repair of the
emission control devices and systemmay
be performed by any nonroad engine repair establishment or individual.
The Emissions Compliance Period referred
to on the Emissions Compliance label indicates the number of operating hours for
which the engine has been shown to meet
Federal emissions requirements.
Category C = 50 hours, B= 125 hours, and
A = 300 hours.
For reference, please fill out the following
information that will be needed for future
servicing of your trimmer:
Model Number:
Serial Number:
Purchase Date:
Purchased From:
WARNING: A clearing saw,
brushcutter or trimmer can be
dangerous if used incorrectly or
carelessly, and can cause serious
or fatal injury to the operator or
others. It is extremely important
that you read and understand the
contents of this operator’s manual.
WARNING: Under no circum-
stances may the design of the
machine be modified without the
permission of the manufacturer.
Always use genuine accessories.
Non--authorized modifications
and/or accessories can result
in serious personal injury or the
death of the operator or others.
Your warranty may not cover
damage or liability caused by the
use of non--authorized accessories or replacement parts.
2
KEY TO SYMBOLS
Symbols
WARNING: Clearing saws, brush-
cutters and trimmers can be dangerous! Careless or incorrect use
can result in serious or fatal
injury to the operator or others.
Please read the operator’s manual
careful ly and make sure you
understand the instructions
before using the machine.
Always wear:
S Hearing protection
S Approved eye protection
Watch out for thrown objects and
ricochets.
Only intended for trimmer heads.
Use unleaded or quality leaded
gasoline and two--stroke oil
mixed at a ratio of 2% (1:50).
Other symbols/decals on the machine
refer to special certification requirements
for certain markets.
Stop the engine by pushing
and holding the stop switch
in the STOP position until the
engine stops before carrying
out any checks or maintenance.
The operator of the machine
must ensure, while working,
that no persons or animals
come closer than 50 feet
(15 meters).
Arrows which show limits for
handle positioning.
Always wear approved protective
gloves.
Wear sturdy, non--slip boots.
Only use non--metallic, flexible
cutting attachments, i.e. trimmer
heads with trimmer line.
Regular cleaning is required.
Visual check.
Approved eye protection must
always be used.
3
SAFETY INSTRUCTIONS
Personal protective equipment
IMPORTANT! Whenever you use a clear-
ing saw, brushcutter or trimmer you must
wear personal protective equipment that is
approved by the authorities. Personal
protective equipment does not eliminate
the risk of accidents, but it can reduce the
effects of an injury in the event of an accident. Ask your dealer for help when
choosing protective equipment.
WARNING: Listen out for warn-
ing signals or shouts when you are
wearing hearing protection. Always
remove your hearing protection as
soon as the engine stops.
GLOVES
Gloves should be worn when necessary,
e.g., when fitting cutting attachments.
HEARING PROTECTION
Wear hearing protection that provides
adequate noise reduction.
FIRST AID KIT
Always have a first aid kit nearby.
Machine’s safety equipment
This section describes the machine’s safety equipment, its purpose, and how checks
and maintenance should be carried out to
ensure that it operates correctly. See the
“Know your trimmer ” section to locate
where this equipment is positioned on your
machine.
The life span of the machine can be reduced
and the risk of accidents can increase if
machine maintenance is not carried out
correctly and if service and/or repairs are not
carried out professionally. If you need further
information please contact your nearest servicing dealer .
WARNING: Never use a machine
that has faulty safety equipment!
Carry out the inspection, maintenance and service routines listed in
this section.
Stop switch
Make sure the engine stops when you push
and hold the stop switch.
EYE PROTECTION
Always wear approved eye protection. If
you use a visor then you must also wear
approved protective goggles. Approved
protective goggles must comply with
standard ANSI Z87.1.
BOOTS
Wear sturdy, non--slip boots.
CLOTHING
Wear clothes made of a strong fabric and
avoid loose clothing that can catch on
twigs and branches. Always wear heavy,
long pants. Do not wear jewelry, shorts
sandals or go barefoot. Secure hair so it is
above shoulder level.
Cutting attachment guard
This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator
from accidental contact with the cutting attachment.
WARNING: Never use a cutting
attachment without an approved
guard. See the section on “Technical
data”. If an incorrect or faulty guard
is fitted this can cause serious
personal injury .
4
SAFETY INSTRUCTIONS
Use ofincorrectly wound trimmer line or an
incorrect cutting attachment increases the
level of vibration.
WARNING: Overexposure to
vibration can lead to circulatory
damage or nerve damage in people
whohaveimpairedcirculation.
Contact your doctor if you experience symptoms of overexposure to
vibration. Such symptoms include
numbness, loss of feeling, tingling,
pricking, pain, loss of strength,
changes in skin color or condition.
These symptoms normally appear
in the fingers, hands or wrists. The
risk increases at low temperatures.
Muffler
The muffler is designed to reduce the noise
level and to direct the exhaust gases away
from the operator.
CAUTION! Muffler is fitted with a catalytic
converter designed to reduce harmful exhaust gases.
Cutting equipment
A trimmer head is intended for trimming
grass.
Checking, maintaining and
servicing the machine’s
safety equipment
IMPORTANT!
All servicing and repair work on the machine
requires special training. This is especially
true of the machine’s safety equipment. If
your machine fails any of the checks described below you must contact your service
agent. When you buy any of our products we
guarantee the availability of professional repairs and service. If the retailer who sells
your machine is not a servicing dealer , ask
him for the address of your nearest service
agent.
Stop switch
S Start the engine and make sure the engine
stops when you push and hold the stop
switch.
For mufflers, it is very important that you follow the instructions on checking, maintaining, and servicing your machine.
See Checking, maintaining and servicing the
machine’s safety equipment section.
WARNING: Mufflers fitted with
catalytic converters get very hot
during use and remain so for some
time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember
the risk of fire!
WARNING: The inside of the
muffler contain chemicals that may
be carcinogenic. Avoid contact with
these elements in the event of a
damaged muffler.
WARNING: Bear in mind that:
Engine exhaust fumes contain carbon monoxide, which can cause
carbon monoxide poisoning. For
this reason you should not start or
run the machine indoors, or anywhere that is poorly ventilated.
The exhaust fumes from the engine
are hot and may contain sparks
which can start a fire. Never start
the machine indoors or near combustible material!
Cutting attachment guard
S Ensure that the guard is undamaged and
is not cracked.
S Replace the guard if it has been exposed
to impact or is cracked.
S Always use the recommended guard for
the cutting attachment you are using. See
section on “Technical data”.
5
SAFETY INSTRUCTIONS
Muffler
S Never use a machine that has a faulty
muffler.
S Regularly check that the muffler is securely
attached to the machine.
S The muffler on this unit is equipped with a
special spark arrestor mesh. The mesh
should be checked and, if necessary.
cleaned by a servicing dealer. A blocked
mesh will cause the machine to overheat,
which can lead to serious damage. Never
use a muffler with adefective spark arrestor mesh. See the Maintenance section.
Cutting equipment
This section describes how to choose and
maintain your cutting equipment in order to:
S Obtain maximum cutting performance.
S Extend the life of cutting equipment.
General rules
1. Only use cutting attachments with the
guards we recommend! See the section
on “Technical Data”.
2. Check the cutting attachment for damage
or cracks. A damaged cutting attachment
should always be replaced.
:
WARNING: Never use a machine
with faulty safety equipment. The
machine’s safety equipment must be
checked and maintained as
described in this section.
If your machine fails any of these
checks contact your service agent to
getitrepaired.
IMPORTANT!
This section describes how to choose and
maintain your cutting equipment in order to:
Obtain maximum cutting performance.
Extend the life of cutting equipment.
Only use cutting attachments with the guards
we recommend! See the section on
“Technical data”.
Refer to the instructions for the cutting attachment to check the correct way to load the
trimmer line and the correct line diameter.
Trimmer head
S Only use the recommended cutting at-
tachments. See the section on “Technical
data”.
S Smaller machines generally require small
trimmer heads and vice versa. This is because when clearing using trimmer line
the engine must throw out the trimmer
line radially from the trimmer head and
overcome the resistance of the grass
being cleared.
S The length of the trimmer line is also im-
portant. A longer trimmer line requires
greater engine power than a shorter
trimmer line of the same diameter.
S Make sure that the cutter on the trimmer
guard is intact. This is used to cut the
trimmer line to the correct length.
S To increase the life of the trimmer line it
can be soaked in water for a couple of
days. This will make the line tougher so
that it lasts longer.
IMPORTANT!
Always ensure the trimmer line is wound
tightly and evenly around the drum, otherwise the machine will generate harmful
vibration.
WARNING: Always stop the en-
gine before doing any work on the
cutting attachment. This continues
to rotate even after the throttle has
been released. Ensure that the
cutting attachment has stopped
completely and disconnect the
lead from the spark plug before
you start to work on it.
6
SAFETY INSTRUCTIONS
General safety precautions
IMPORTANT!
S The machine is only designed for trimming
grass.
S The only accessories you can operate
with this engine unit are the cutting attachments we recommend in the “Technical data” section.
S Never use wire, rope, string, etc.
S Never use the machine if you are tired, if
you have drunk alcohol, or if you are taking medication that could affect your vision, your judgment or your coordination.
S Never use the machine in extreme weath-
er condi tion s such as severe cold, very hot
and/or humid climates.
S Never use a machine that has been modi-
fied in any way from its original specification.
S Wear personal protective equipment. See
instructions in the “Personal protective
equipment” section.
S Never use a machine that is faulty. Carry
out the checks, maintenance and service
instructions described in this manual.
Some maintenance and service measures
must be carried out by trained and qualified specialists. See instructions in the
“Maintenance” section.
S All covers and guards must be fitted before
starting. Make sure the spark plug cap and
lead are not damaged. Otherwise you
could get an electric shock.
S The machine operator must ensure that
no people or animals come closer than
50 feet (15 meters) while working.
S Stay clear of spinning line.
S Secure or remove loose clothing or cloth-
ing with loosely hanging ties, straps, tassels, etc. They can be caught in moving
parts.
S Being fully covered also helps protect you
from debris and pieces of toxic plants
thrown by spinning line.
S Keep handles free of oil and fuel.
S Always keep the engine on the right hand
side of your body.
S Hold the unit firmly with both hands.
S Keep trimmer head below waist level and
away from all parts of your body. Do not
raise engine above your waist.
S Keep all parts of your body away from
muffler and spinning line. Keep engine below waist level. A hot muffler can cause
serious burns.
S Keep firm footing and balance. Do not
overreach or use from unstable surfaces
such as ladders, trees, steep slopes, rooftops, etc.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual.
WARNING: A faulty cutting at-
tachment may increase the risk of
accidents.
Personal protection
S Always wear boots and
other equipment described
in the “Personal protective
equipment” section.
S Always wear working
clothes and heavy--duty
long pants.
S Never wear loose fitting
clothes or jewelry.
S Persons with long hair
should (for personal safety)
put their hair up.
Safety instructions regarding the
surroundings
S Never allow children to use the machine.
S Ensure no one comes closer than 50 feet
(15 meters) when working.
S Never allow anyone else to use the
machine without first ensuring that they
have understood the contents of the
operator’s manual.
Safety instructions before starting
work
S Inspect the working area. Remove any
objects such as stones, broken glass,
nails, steel wire, string, etc. that can be
thrown or can wrap around the cutting
head or shaft.
S Keep others at a safe distance. Children,
animals, onlookers and helpers should
stand outside of the safety zone of 50
feet (15 meters). Stop the machine immediately if anyone should approach.
S Check the entire machine before starting
work. Replace damaged parts. Check for
fuel leakage and that all safety guards
and covers are complete and fastened
securely. Check all nuts and bolts.
S Check the cutting head
for cracks or any other
damage.
S Ensure the trimmer guard
is mounted and not
damaged.
7
Loading...