Husky Balance Vapor Owner's Manual

MODEL #5900

Recommended Installation, Maintenance

and Inspection Instructions

Balanced Single-Use Safe-T-Break

®

WARNING This device separates at less than 250 lbf / 1,112.1 N pull force!

INSTALLATION INSTRUCTIONS

NOTE: Prior to installation, it shall be determined that such pull force will not damage the hose assembly or
dispensing device. The dispensing device must be securely bolted to dispensing island.

1. Turn off dispenser and relieve line pressure.

2. Attach scale to where the Safe-T-Break® will be installed. Apply 250 lbf / 1,112.1 N
pull force at various angles then check dispenser and hose for damage. Refer to
UL 567 for details. If no damage occurred, release pull and complete installation.

3. Install Safe-T-Break® in the direction of the ow arrows.

4. Do not use thread sealant (Teon tape, anti-seize or any other kind of sealant).

5. Tighten rmly but do not overtighten. Refer to UL 567 for details.

6. High hose dispenser – Install the Safe-T-Break® between the hose sections. Verify
that the whip hose is the correct length.

7. Low hose dispenser – Install the Safe-T-Break® down stream of any hose retractor
cable coupling.

DO NOT OVERTIGHTEN. DO NOT WRENCH ACROSS COUPLING.

DO NOT INSTALL DIRECTLY TO THE DISPENSER.

IF SEPARATION OCCURS

• Turn off dispenser and relieve line pressure.

• Inspect the entire dispensing system for damage.

• Conduct pull test for dispenser integrity (see step 2 of installation instructions

above).

• Replace Safe-T-Break® – do not reinstall.

• Check for electrical conductivity.

• Check for proper ow of fuel.

• Check for meter creep leakage per California Department of Food and Agriculture

Device Enforcement Manual, EPO #26-A-4 through #26-A-5 section 1.

5900

TESTING / MAINTENANCE / INSPECTION

Daily

• Check for leaks / stains.

• Check for damage.

Monthly

• Check "remove after" date.

Annually

• Conduct vapor leak test.

• Never keep in service past
recommended life.

Husky Corporation • 2325 Husky Way • Pacic, MO 63069 • Phone: [phone] • Fax: [phone] • www.husky.com

• All drive aways, maintenance and
inspection activities must be logged
using the serial number of the individual
product.

• Apply city, state, or federal testing
regulations as appropriate.

ANY TEST / INSPECTION FAILURE

REQUIRES IMMEDIATE EQUIPMENT

REPLACEMENT OR REMOVAL FROM

SERVICE.

MADE IN THE USA

009181-3 4/2009

ALWAYS ADHERE TO INSTALLATION / USAGE INSTRUCTIONS AND WARNINGS.

Improper use may result in injury, damage, or hazardous spill.

GENERAL WARNINGS / INSTRUCTIONS

• Use of equipment is at individuals’ own risk.

• Always abide and adhere to city, state, and
federal regulations regarding use and
installation of dispensing equipment.

• Always follow the product manufacturer’s
installation and maintenance instructions.

• Always turn off all power to dispenser
during maintenance and inspection activities.

• Always close the shear valves during
maintenance and inspection activities.

• Always relieve pressure from system prior
to performing maintenance activities.

• Always check continuity after installation
using a megohmeter (Refer to PEI RP 400
for details).

• Always replace or remove from service
damaged or leaking dispensing equipment
immediately.

• Always report leaks / spills / accidents to
appropriate authorities.

• Always wear appropriate safety equipment
during maintenance activities.

• Always have appropriate re extinguishing
equipment within 5 ft / 1.5 m of dispensers.

• Never use thread sealant (Teon tape, anti­seize or any other other kind of sealant).

• Always place containers on the ground
before lling.

• Always discharge static electricity before
using or servicing equipment by touching a
metal part of the dispenser before and after
fueling vehicle.

• Never smoke within 20 ft / 6.1 m of
dispensers.

• Never keep in service past recommended
life.

• Never leave the nozzle unattended while
dispensing fuel.

• Never use sparking or aming devices within
20 ft / 6.1 m of dispensers.

• Never use power tools near dispensers or to
aid in the installation process.

• Never use cell phone within 20 ft / 6.1 m of
dispensers.

• Never reenter car when fueling vehicle.

• Never allow gasoline to touch eyes or skin.

• Never use at ow rates in excess of
regulatory guidelines.

• Never use at ow rates less than 5 gpm /

18.9 Lpm.

• Never dispense ammable material into
unapproved containers.

• Never dispense fuel without a valid
driver’s license.

Patents pending

Listings

WARRANTY

VAPOR PRODUCTS – Husky Corporation will, at its option, repair, replace, or credit the purchase price of any Husky

manufactured product which proves upon examination by Husky, to be defective in material and/or workmanship for a period of one (1)

year of installation or fteen (15) months from the manufacture date of shipment by Husky, whichever occurs rst. The warranty period on

repaired or replacement vapor recovery products is only for the remainder of the warranty period of the defective product.

CONVENTIONAL PRODUCTS – Husky Corporation will, at its option, repair, replace, or credit the purchase price of any Husky

manufactured product which proves upon examination by Husky, to be defective in material and/or workmanship for a period of one (1)

year from the manufacture date of shipment by Husky.

Buyer must return the products to Husky, transportation charges prepaid. This Warranty excludes the replaceable bellows,

bellows spring assembly, spout assembly and scuff guard, unless (i) damage is obvious when the product is removed from shipping carton

and (ii) the defective product is returned to Husky prior to use. This warranty does not apply to equipment or parts which have been installed

improperly, damaged by misuse, improper operation or maintenance, or which are altered or repaired in any way.

The warranty provisions contained herein apply only to original purchasers who use the equipment for commercial or

industrial purposes. There are no other warranties of merchantability, tness for a particular purpose, or otherwise, and any other such

warranties are hereby specically disclaimed.

Husky assumes no liability for labor charges or other costs incurred by Buyer incidental to the service, adjustment, repair, return,

removal or replacement of products. Husky assumes no liability for any incidental, consequential, or other damages under any warranty,

express or implied, and all such liability is hereby expressly excluded.

Husky reserves the right to change or improve the design of any Husky fuel dispensing equipment without assuming any

obligations to modify any fuel dispensing equipment previously manufactured.

Husky Corporation • 2325 Husky Way • Pacic, MO 63069 • Phone: [phone] • Fax: [phone] • www.husky.com

009181-3 4/2009