Page 1
Husky C range chillers
Commercial refrigeration range
User Manual
To ensure safe operation, please read this instruction manual thoroughly
before use.
Welcome to your new Husky
Thank you for buying this Husky commercial chiller. It has been
designed and manufactured for many years of trouble-free service.
Operation is very simple, but please take a few minutes to read this
booklet. It contains safely information, and tips to ensure you receive
from your chiller.
WARNING: RISK OF ELECTRICAL SHOCK
HAZARD
USERS IN EUROPE This unit must be earthed.
If the power cable is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid hazard..Ensure
that the appliance is properly earthed. Stop using the
appliance immediately if electric shock is felt when
touching the chiller.
DISPOSAL OF OLD APPLIANCES
BE SURE TO MAKE ANY LOCKS UNUSABLE, REMOVE ANY
DOOR(S) AND DISCARD SEPARATELY.
WARNING-CHEMICAL HAZARD: DO NOT ALLOW CHILDREN
TO PLAY WITH THE OLD APPLIANCE. CONTACT YOUR
LOCAL AUTHORITY DISPOSAL PROCEDURES.
Before disposing of an old appliance, please make sure it is switched off
and safe. Unplug the appliance and break any locks in order to avoid
children becoming trapped.
-1-
Page 2
Please note: the refrigeration system contains gases and refrigerants
which require specialist waste disposal. The valuable materials in a
refrigerator can be recycled .Contact your local waste disposal depot for
proper disposal of an old appliance and contact your local authority or
dealer if you have any questions.
Please ensure the pipe work of your refrigerator is not damaged prior to
disposal. You can contribute to environmental awareness by insisting on
an appropriate non-polluting method of disposal.
Please keep this booklet in a safe place for future reference. If you ever
sell your Husky chiller, hand this user manual to the new owner.
The manufacture does not accept responsibility for any damages that may
arise due to non-observation of these instructions. The user is liable for
any material damage or bodily injury(product liability) cause by using the
refrigerator carelessly or failing to follow instructions.
Do not use damaged appliances. If you are in any doubt, consult an
engineer.
DISPOSAL OF PACKAGING
Do not allow children to play the packaging, and destroy plastic bags
safely.
The cardboard may be broken or cut into smaller pieces and given to a
waste paper disposal service. The wrapping foil is made of polyethylene.
The polyethylene pads and stuffing contain no fluorochloric
hydrocarbons.
All these valuable materials may be taken to a waste collecting depot and
used again after adequate recycling .Consult your local authority for the
name and address of the waste paper disposal services nearest to you.
IMPORTANT SAFETY INSTRUCTIONS
Before switching on your Husky chiller for the fist time, read the
information in this user manual carefully. The manual contains important
observations relating to the assembly, operation and maintenance of the
appliance.
Connection and installation of your Husky chiller are to be carried
out in strict compliance with the relative instructions in this manual.
For safety, the appliance must be properly earthed in accordance with
specifications
Do not damage any parts of the appliance which carry refrigerant by
piercing, perforating, crushing, twisting or scraping. If the refrigerant
comes into contact with the eyes, it may cause serious eye injury.
Always remember to unplug the appliance before cleaning. Never
unplug your appliance by pulling on the power cable. Always grip
plug firmly and pull straight out from the socket. Always check that
the plug and cable are undamaged.
All repairs must be carried out by qualified engineers. Inadequate
repairs may be dangerous. Never try to repair the refrigerator
yourself.
Should the cover of the interior light or fan fall off or break, switch
the refrigerator off immediately and replace the cover.
Ensure your chosen location has a flat and stable surface. The unit
may be leveled by turning either or both of the adjustable feet in the
front corners. Check the unit is level using a spirit level.
-2-
-3-
Page 3
Do not obstruct or cover the ventilation aperture.
Do not allow children to play with the appliance, or to sit on it or to
hang onto the door(S).
Make sure there is a suitable power Outlet (220 volts, 13 amps outlet)
with proper grounding to power the refrigerator.
OPERATION
Place the shelves firmly on their supports. The maximum load for a
shelf is 40Kg. Check that the refrigerator is functioning properly before
installing and filling it. The electronically thermostat is located inside
the unit. An optional light switch is inside the unit.
BEFORE USING FOR THE FIRST TIME
Do not position this appliance with its rear panel directly against a wall.
For good circulation and operating efficiency, the ventilation grilles
must never be blocked.
Remove all packaging and place the chiller on a stable, secure flat
surface. Position the chiller away from heat sources, where the unit is
well-ventilated and protected from moisture, or extremes of heat or cold.
The refrigerator may not function properly if the temperature rises
above +30 (standard models). The refrigerator meets the operating
conditions according to the standard EN 441-4 in climate class 4.
A 10A fuse is fitted. Never replace with a fuse rated higher than this.
NEVER USE AN EXTENSION LEAD. If the mains cable will not
reach the nearest socket, either rearrange your store layout or ask a
qualified electrician to fit a new socket.
If power is cut off, wait for at least 5 minutes before plugging the unit
in again to avoid damaging the compressor.
Do not place combustible, explosive or volatile articles, corrosive acid
or alkali, or liquid in glass containers into the chiller. Always exercise
caution if adjusting the temperature.
IMPORTANT: allow the refrigerator to stand
upright for 8 hours before plugging in.
-4-
Never put warm or hot foods directly into the chiller.
ELECTRONICAL THERMOSTAT
Press the “SET” key more than 3 seconds, the
display will flash, select the desired target
temperature by pressing the “SET” key,
the temperature may be adjusted between 2-12℃.
¡ æ
SET
CLEANING
1. UNPLUG your Husky chiller and remove any stock to a suitable
back-up chiller.
2. Wash the inner compartment with warm water and neutral detergent.
DO NOT allow the control panel, cables or plug to get wet.
NEVER use corrosive detergents, wire brushes, or abrasive scourers to
clean your chiller.
NEVER use metal or sharp implements to remove debris.
3. Dry all surface thoroughly.
4. To ensure trouble-free operation the condenser should be cleaned
every three months where appropriate using a vacuum hose. The
condenser is located behind lower grill of the cabinet. In exceptionally
dusty
-5-
Page 4
locations the condenser should be cleaned more often.
5. Use mild soapy water to clean the gasket and seals.
REPLACING LAMPS
1. Unplug the power plug.
2. Remove the screws on both end of the light cover, take down the
lamp cover, pull out the wires, then take away the lamp.
3. Install the new lamp, connect the wires, place the lamp cover and
fasten it.
CIRCUIT DIAGRAM
Model:、HUS-HDA-C2H、HUS-HAD-C2S
Over Load
Protector
Outside
Power
plug
Switch
Inner
Lamp
PCB
Sensor
FM
1
Display
～
Fan
Inner
FM
Fan
1
～
Compressor
-6-
Model: HUS-HDA-C3
Power
plug
Switch
Inner
Lamp
PCB
Sensor
FM
1
～
Display
Outside
Fan
FM
1
～
Outside
Fan
FM
1
～
Inner
Fan
Starter
Inner
FM
Fan
1
～
Starter
Over Load
Protector
Compressor
Page 5
Loading...