Humminbird 531655-1-A User Manual

1100 Series™ In-Dash Mounting Kit

Thank You

Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its reputation by designing and manufacturing top-quality, thoroughly reliable marine equipment. Genuine Humminbird® accessories offer the opportunity to upgrade and expand the capabilities of your Humminbird® product.

Your Humminbird® is designed for trouble-free use in even the harshest marine environment. In the unlikely event that your Humminbird® does require repairs, we offer an exclusive Service Policy - free of charge during the first year after purchase, and available at a reasonable rate after the one-year period. For complete details, see the Warranty section included in this manual.

Contact our Customer Resource Center at either 1-800-633-1468 or visit our website at www.humminbird.com.

Installation Overview

Following are instructions for the installation of this accessory. Before you start installation, we encourage you to read these instructions carefully in order to get the full benefit from your Humminbird® accessory.

If you find that any items are missing from your installation kit, call our Customer Resource Center at 1-800-633-1468 or visit our website at www.humminbird.com.

531655-1_A

Installation

Start by placing the components on the surfaces where you intend to install them before installation. Make sure that the surfaces you have chosen provide adequate protection from wave shock, and that all cables can reach the control head.

NOT E: If a cable is too short for your application, extension cables are available. Call Humminbird® Customer Support at 1-800-633-1468 for more information.

Parts and tools specific to In-dash mounting are:

• Threaded rods and hardware

• In-dash mounting foam pads

• In-dash mounting template

• Reciprocating saw for cutting dash material

• Masking tape to hold mounting template in place.

1. Locate a suitable, flat area of the dash to mount the control head. The control head requires a depth of at least 4 inches (102 mm).

2. Tape the paper In-Dash Mounting template to the desired in-dash mounting location.

3. At a location inside the dotted line on the template, drill a hole large enough to insert blade of reciprocating saw. In addition, drill the 4 mounting hole locations using a 3/16" drill bit. Carefully begin cutting toward the dotted line, then follow the dotted line around the template. Remove the template when finished.

Mounting the Control Head

Foam Pads

Cut Away Dash

Threaded Rod

Washer

Wing Nut

Lock Washer

4. Insert and tighten the four threaded rods into the four threaded inserts located on the back side of the control head. Peel off the adhesive-backed foam pads and place them on the back of the control head; make sure you notice the difference between the longer top/bottom and shorter side pads.

Foam Pads

1100 Series™ In-Dash Mounting Kit

. Insert the control head through the mounting hole from the front side of the dash.

Place a washer, lock washer, and wing nut onto each threaded rod and tighten fully.

6. Thread the cables through the opening in the back of the cable collector cover.

7. Insert cable connectors into the proper recesses on the cable collector insert. The cable connectors are keyed to prevent reverse installation, so be careful not to force the connectors into the wrong slots. If you don’t have a cable for every hole in the insert, install the blank plugs to protect the control head from the weather.

8. Line up the cable collector insert and cover, with the keying feature, then slide the cover into place on the insert.

Assembling the Cable Collector

Cable Collector Insert

531655-1_A

Inserting the Cables into the Cable Connector Insert

Power Communications

Temp/Speed

Cable Collector Cover

Transducer

Screws

Cable Collector Cover

9. Attach the cable collector insert to the cable collector cover using the (2) #6 Phillips screws provided.

10. Plug the assembled cable collector into the back of the control head, pushing gently but steadily until you feel the collector snap into place. Cable connectors and cable sockets are keyed to prevent reverse installation, so be careful not to force the connectors into the wrong sockets.

Plugging the Assembled Cable Connector into the Back of the Control Head

Cable Collector Insert

NOTE: You may wish to dress the cabling with nylon wire ties in order to hold the cables

together and create a cleaner assembly.

NOTE: It is very important that the cable collector is used and secured in place in the In-Dash installation.

The Humminbird® 1100 Series™ control head is now ready for operation.

+ 2 hidden pages