Portable System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
WARNING!
READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT.
FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY.
REQUIRED TOOLS AND MATERIALS:
•Two People
•Tape Measure
•Wood Board (Scrap)
•Wrenches: (Two) 7/16”, 1/2”, 9/16”, 3/4” or Large and Small Adjustable Wrenches
•Sawhorse or Support Table
•Step Ladder 8 ft. (2.4 m)
•Garden Hose or Sand (225 lb.) (102 kg)
•Hammer
•Tape
•Phillips Screwdriver
•Safety Goggles
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-333 061
Internet Address: http://www.huffysports.com
1 |
07/04 |
P/N 21192302 |
© COPYRIGHT 2004 by HUFFY SPORTS
|
BEFORE YOU START! |
To ensure optimal playability of backboard system, a close tolerance fit between the elevator |
|
components and hardware is required. Test-fit large bolts into large holes of elevator tubes, |
|
backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out |
|
|
any excess paint from holes if necessary. |
|
AVANT DE COMMENCER ! |
Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien |
|
ajustés (serrés). À titre d'essai, insérez les gros boulons dans les gros trous des tubes du système élévateur, des supports |
|
du panneau et des plaques triangulaires. Basculez-les avec précaution en imprimant un mouvement circulaire pour |
|
|
éliminer l'excédent de peinture, si nécessaire. |
|
¡ANTES DE COMENZAR! |
Para asegurar el óptimo rendimiento del sistema del respaldo en el juego, se requiere un ajuste de tolerancia estrecha |
|
entre los componentes del elevador y el herraje. Pruebe el ajuste de los pernos grandes en los orificios grandes de los |
|
tubos elevadores, soportes del respaldo y placas triangulares. Cuidadosamente muévalos en círculos para eliminar |
|
|
cualquier exceso de pintura, si es necesario. |
|
VORBEREITENDE MASSNAHMEN |
Um sicherzustellen, dass das Korbwandsystem optimal für den Spielbetrieb geeignet ist, müssen die Komponenten der |
|
Verlängerungsvorrichtung und die verschiedenen Befestigungsteile fest miteinander verschraubt werden. Große Schrauben |
|
zur Probe in die großen Löcher der Verlängerungsrohre, Korbwandklammern und Dreiecksplatte stecken und diese |
|
vorsichtig in einer Kreisbewegung hinund herbewegen, um eventuelle Farbrückstände aus den Bohrungen zu entfernen. |
|
P/N 21192302 07/04 |
2 |
WARNING
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
Owner must ensure that all players know and follow these rules for safe operation of the system.
•DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
•During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
•Do not slide, climb, shake or play on base and/or pole.
•After assembly is complete, fill system completely with water or sand and stake to the ground. Never leave system in an upright position without filling base with weight, as system may tip over causing injuries.
•When adjusting height or moving system, keep hands and fingers away from moving parts.
•Do not allow children to move or adjust system.
•During play, do not wear jewelry (rings, watches, necklaces, etc.). Objects may entangle in net.
•Surface beneath the base must be smooth and free of gravel or other sharp objects. Punctures cause leakage and could cause system to tip over.
•Keep organic material away from pole base. Grass, litter, etc. could cause corrosion and/or deterioration.
•Check pole system for signs of corrosion (rust, pitting, chipping) and repaint with exterior enamel paint. If rust has penetrated through the steel anywhere, replace pole immediately.
•Check system before each use for proper ballast, loose hardware, excessive wear and signs corrosion and repair before use.
•Check system before each use for instability.
•Do not use system during windy and/or severe weather conditions; system may tip over. Place system in the storage position and/or in an area protected from the wind and free from personal property and/or overhead wires.
•Never play on damaged equipment.
•See instruction manual for proper installation and maintenance.
•When moving system, use caution to keep mechanism from shifting.
•Keep pole top covered with cap at all times.
•Do not allow water in tank to freeze. During sub-freezing weather add non-toxic antifreeze, sand or empty tank completely and store. (Do not use salt.)
•Use extreme caution if placing system on sloped surface. System may tip over more easily.
In the U |
-558-5234 |
Canada: 1-800- |
8339 |
201241 2/99
3 |
07/04 |
P/N 21192302 |
NOTICE TO ASSEMBLERS
ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
IMPORTANT!
Remove all contents from boxes. Be sure to check inside pole sections;
hardware and additional parts are packed inside.
WARRANTY CARD:
Please remember to complete your product registration form either on-line at: www.huffysports.com or mail-in the enclosed postcard.
WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC
BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY
HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD
COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED
IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE
NUMBER FOR FREE REPLACEMENT:
U.S. 1-800-558-5234; CANADA: 1-800-284-8339; http://www.huffysports.com
For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com.
P/N 21192302 07/04 |
4 |
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and operated properly. Check entire box and inside all packing material for parts and/or additional instructional material. Before beginning assembly, read the instructions and identify parts using the hardware identifier and parts list in this document.
•If using a ladder during assembly, use extreme caution.
•Two (2) people are recommended for this operation.
•Check base regularly for leakage. Slow leaks could cause system to tip over unexpectedly.
•Seat the pole sections properly (if applicable). Failure to do so could allow the pole sections to separate during play and/or transport of the system.
•Climate, corrosion or misuse could result in system failure.
•Minimum operational height is 6'6" (1.98 m) to the bottom of backboard.
•This equipment is intended for home recreational use only and NOT excessive competitive play.
•Read and understand the warning label affixed to pole. Label is shown to the right.
•The life of your basketball pole depends on many conditions: climate, placement of pole, the location of pole, exposure to corrosives such as pesticides, herbicides or salts. These are all important factors.
•If technical assistance is required, contact Huffy Sports.
•Adult supervision is recommended when adjusting height.
Most injuries are caused by misuse and/or not following instructions. Use caution when using this system.
For more information on assembly, placement, proper use and maintenance, visit The American Basketball Council website at http://www.smarthoops.com.
54
HEIGHT ADJUSTMENT
TO ADJUST BACKBOARD:
1
1. While holding handle, remove pin. |
3 |
2. Move elevator up or down to desired height.
3. Replace pin full length to lock system at desired height.
|
2 |
|
MOVING SYSTEM |
|
|
1. |
Adjust basketball backboard |
|
1 |
height to lowest position. |
|
2. |
While holding pole, rotate |
|
|
basketball system forward |
|
|
until wheels engage with |
|
|
ground. |
|
3. |
Move basketball system to |
|
|
desired location. |
|
4. |
Carefully rotate basketball |
|
3 |
system upright. |
|
4 |
|
|
|
|
|
5. |
Reattach ground restraint and |
|
|
check system for stability. |
|
|
201252 |
2/99 |
5 |
07/04 |
P/N 21192302 |
Get to know the basic parts of your basketball system.....
FRONT
BACKBOARD
RIM
ELEVATOR
SYSTEM
POLE
SUPPORT
STRUT
BASE
WHEELS
P/N 21192302 07/04 |
6 |
PARTS LIST - See Hardware Identifier
PARTS LIST - See Hardware Identifier
Item Qty.Part No. Description
1 |
1 |
206336 |
Tank |
2 |
2 |
206330 |
Wheel Axle, 4-1/4 Long |
3 |
2 |
226401 |
Wheel, 4 “ (Black) |
4 |
1 |
904847 |
Top Pole Section |
5 |
1 |
908481 |
Middle Pole Section |
6 |
1 |
908487 |
Bottom Pole Section |
7 |
1 |
202820 |
Rod, 3/8 O.D. x 4-3/4 Long |
8 |
1 |
202822 |
Eyebolt, 3/8-16 x 3-3/4 Long |
9 |
1 |
202821 |
Disk, 2-3/4 Diameter |
10 |
1 |
203063 |
Nylon Insert Lock Nut, 3/8-16 |
11 |
2 |
906410 |
Strut, 1” O.D. x 43 Long |
12 |
1 |
203220 |
Nut, Nylock, 5/16-18 |
13 |
7 |
203218 |
Washer, 5/16 Flat |
14 |
1 |
201625 |
Bolt,Yellow Dichromate,5/16-18 X 3.60 Long |
15 |
2 |
203798 |
Bolt, Hex Flange, 5/16-18 x 1-1/2 Long |
16 |
11 |
203100 |
Hex Flange Nut 5/16-18 |
17 |
1 |
204832 |
Bracket, Pole Mount |
18 |
2 |
203231 |
Carriage Bolt, 5/16-18 x 3-1/2 Long |
19 |
4 |
203232 |
Washer, metal, 3/4” O.D. |
20 |
3 |
201124 |
Locknut, Hex Head, 3/8-16 |
21 |
3 |
206360 |
Bolt, Hex Head, 3/8-16 x 2-5/8 Long |
22 |
2 |
204858 |
Spacer, Biscut, plastic |
23 |
2 |
204857 |
Spacer, metal 1/2” O.D.x1.44 Long |
24 |
2 |
204859 |
Cover, Spring |
25 |
3 |
203038 |
Carriage Bolt, 5/16-18 x 2-3/4 Long |
26 |
1 |
204850 |
Pin, Locking |
27 |
1 |
204853 |
Lanyard, Black Coil |
28 |
1 |
904833 |
Height Adjustment Rod |
29 |
1 |
204872 |
Label, Height Indicator |
30 |
2 |
203103 |
Carriage Bolt, 5/16-18 x 2 Long |
31 |
1 |
204803 |
Screw, Phillips Head |
32 |
1 |
204855 |
Handle, Left |
33 |
1 |
204856 |
Handle, Right |
34 |
2 |
900846 |
Board Bracket |
35 |
1 |
203493 |
Nut, 1/4-20, Center Lock |
36 |
2 |
201129 |
Spacer, .402 I.D. x .5 O.D. x 1.8 Long |
37 |
1 |
240017 |
Bolt, Hex Head, 1/4-20 x 2-1/4 Long |
38 |
6 |
206311 |
Spacer, Plastic, .530 I.D. x .50 Long |
39 |
7 |
206340 |
Locknut, Hex Head, 1/2-13 |
40 |
2 |
904820 |
Elevator Tube, Lower-Long |
41 |
1 |
204838 |
Spring |
42 |
1 |
|
Rim |
43 |
2 |
904808 |
Elevator Tube, Upper-Short |
44 |
4 |
201651 |
Spacer, 1/4 Long x 1/2 O.D. |
45 |
2 |
900867 |
Plate, Triangle, (Black) |
46 |
1 |
202814 |
Cap, Pole Top |
47 |
6 |
206244 |
Bolt, Hex, 1/2-13 x 8 Long |
48 |
1 |
204870 |
Bolt, Hex, 1/2-13 x 3-1/2 Long |
49 |
2 |
203617 |
Plug Cap |
50 |
12 |
201219 |
Smart Clip, Net Holder, |
51 |
1 |
|
Net |
52 |
1 |
201568 |
Anchor, T-Strap |
53 |
1 |
203124 |
Stake, Tie Down |
54 |
1 |
201252 |
Label, Height Adjustment and Moving |
55 |
6 |
202862 |
Spacer .563 I.D. x 1.19 Long |
56 |
1 |
203365 |
Rim Spacer, Plastic |
* You may have extra parts with this model.
7 |
07/04 |
P/N 21192302 |
HARDWARE IDENTIFIER (BOLTS)
Item #8 (1)
Item #31 (1)
Item #18 (2)
Item #37 (1)
Item #25 (3)
Item #21 (3) |
Item #47 (6) |
|
Item #30 (2)
Item #48 (1)
Item #15 (2)
Item #14 (1)
* You may have extra parts with this model.
P/N 21192302 07/04 |
8 |