Huawei RRU3249 User Manual

Issue Date

Compliance and Safety Manual

RRU3249

01 2014-9-1

HUAWEI TECHNOLOGIES CO., LTD.

No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice

The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang Shenzhen 518129

People's Republic of China Website: http://www.huawei.com Email: support@huawei.com

Issue (02)

Huawei Proprietary and Confidential

1 Safety

About This Chapter

1.1 Health and Safety

1.2 Equipment Safety

1.3 Electromagnetic Field Exposure

1.1 Health and Safety

1.1.1 Overview

1.1.2 Electrical Safety

1.1.3 Inflammable Environment

1.1.4 Radiation

1.1.5 Working at Heights

1.1.6 Mechanical Safety

1.1.7 Bundling Signal Cables

1.1.1 Overview

Introduction

This section describes the safety precautions you must take before installing or maintaining Huawei equipment.



To ensure safety of humans and the equipment, pay attention to the safety symbols on the equipment and all the safety instructions in this document.



The "NOTE", "CAUTION", and "WARNING" marks in other documents do not represent all the safety instructions. They are only supplements to the safety instructions.



Installation and maintenance personnel must understand basic safety precautions to avoid hazards.



When operating Huawei equipment, in addition to following the general precautions in this document, follow the specific safety instructions given by Huawei.

Issue (02) Huawei Proprietary and Confidential

1-1

1 Safety



Only trained and qualified personnel are allowed to install, operate, and maintain Huawei equipment.



To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Local Safety Regulations

When operating Huawei equipment, you must follow the local laws and regulations. The safety instructions in this document are only supplements to the local laws and regulations.

General Requirements

To minimize risk of personal injury and damage to equipment, read and follow all the precautions in this document before performing any installation or maintenance.

Ensure that the instructions provided in this document are followed completely. This section also provides guidelines for selecting the measuring and testing devices.

Installation

Ground

Power Supply



The device (or system) must be installed in an access-controlled location.



Tighten the thumbscrews by using a tool after initial installation and subsequent access to the panel.



Do not damage the ground conductor or operate the device in the absence of a properly installed ground conductor. Conduct the electrical inspection carefully.



The device (or system) must be connected permanently to the protection ground before an operation. The cross-sectional area of the protective ground conductor must be at least

1.5 mm



The device must be fixed securely on the floor or other reliable objects, such as the walls

and the mounting racks before operation.



When installing the unit, always make the ground connection first and disconnect it last



For DC-supplied model: The device applies to DC power source that complies with the Safety Extra-Low Voltage (SELV) requirements in IEC 60950-1 based safety standards.



Prepared conductors are connected to the terminal block, and only the appropriate AWG/Type of wire is secured with the lug terminals.



This device relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 80 VDC, 30A for DC supplied model is used on the phase conductors (all current-carrying conductors).



For this device, a readily accessible disconnect device shall be incorporated external to the equipment

1-2 Huawei Proprietary and Confidential

Issue (02)

+ 12 hidden pages