How it Works
Huawei
Loading...
BTS3601C-1900
User Manual
40 pgs654.04 Kb0
User Manual
22 pgs163.74 Kb0
User Manual
75 pgs2.17 Mb0
User Manual
82 pgs2.46 Mb0

Huawei BTS3601C-1900 User Manual

Installation Manual iSiteC BTS3601C CDMA Base Station
Software Installation & System Commissioning
Table of Contents
Table of Contents
1.1 Overview of Software Installation................................................................................1-1
1.1.1 BTS Operational Software................................................................................1-1
1.1.2 Terminal O&M Software...................................................................................1-2
2.1 Software Features .....................................................................................................2-1
2.2 Installing Local O&M Software....................................................................................2-1
2.2.1 Operational Environment..................................................................................2-1
2.2.2 Conditions.......................................................................................................2-2
2.2.3 Network Configuration......................................................................................2-2
2.2.4 Software Installation and Instructions ................................................................2-3
2.3 Installing Remote O&M Software................................................................................2-3
2.3.1 Operational Environment..................................................................................2-3
2.3.2 Conditions .......................................................................................................2-3
2.3.3 Software Installation and Instructions ................................................................2-3
3.1 Software Media.........................................................................................................3-1
3.2 Replacing the Chip....................................................................................................3-1
3.3 Downloading Software...............................................................................................3-2
3.3.1 Methods of Software Loading............................................................................3-2
3.3.2 Remote Loading ..............................................................................................3-3
3.3.3 Verifying the Software Version..........................................................................3-7
4.1 Modes of System Commissioning...............................................................................4-1
4.1.1 Local Commissioning.......................................................................................4-1
4.1.2 Remote Commissioning....................................................................................4-1
4.2 Power-on Operation of Software.................................................................................4-1
4.2.1 Board Startup and Indicator Description.............................................................4-2
4.2.2 Setting up OML................................................................................................4-2
4.2.3 Setting up Abis Signaling Link...........................................................................4-3
4.2.4 Setting up Cells................................................................................................4-3
4.2.5 Normal Operational Status................................................................................4-3
4.2.6 Clock Reference Source...................................................................................4-3
4.3 Commissioning Board Software..................................................................................4-4
4.3.1 Testing Links...................................................................................................4-4
4.3.2 Processing Faults and Alarms...........................................................................4-4
i
Installation Manual iSiteC BTS3601C CDMA Base Station
4.3.3 Operation and Maintenance..............................................................................4-5
Software Installation & System Commissioning
Table of Contents
4.4 Call Function Test......................................................................................................4-9
4.4.1 Test Equipment................................................................................................4-9
4.4.2 Preparations for Service Function Test..............................................................4-9
4.4.3 Service Flow Overview...................................................................................4-10
4.4.4 Test of Location Update Flow..........................................................................4-11
4.4.5 Test of MOC Flow..........................................................................................4-12
4.4.6 Test of MTC Flow...........................................................................................4-12
4.4.7 Test of Handoff Flow......................................................................................4-13
4.4.8 Test of Mobile Originated SMS Flow................................................................4-14
4.4.9 Test of Mobile Terminated SMS Flow..............................................................4-14
4.4.10 Test of Mobile Originated Packet Data Flow...................................................4-15
4.4.11 Test of MS Packet Data Flow (Downlink Service Rate) ...................................4-15
4.4.12 Processing of Abnormalities in the Test.........................................................4-16
ii
Installation Manual iSiteC BTS3601C CDMA Base Station
Software Installation & System Commissioning
Table of Contents
Table of Contents
1.1 Overview of Software Installation................................................................................1-1
1.1.1 BTS Operational Software................................................................................1-1
1.1.2 Terminal O&M Software ...................................................................................1-2
i
Installation Manual iSiteC BTS3601C CDMA Base Station
Software Installation & System Commissioning
1 Overview of Software Installation
1.1 Overview of Software Installation
BTS3601C software includes BTS operational software and terminal Operation & Maintenance (O&M) software.
BTS operational software includes BOOT software, Central Processing Unit (CPU) software, and Field Programmable Gate Array (FPGA) logic.
CPU software includes Micro-bts Base-band Processing Board (MBPB) software and Micro-bts Transceiver Board (MTRB) software; while FPGA logic includes MBPB logic and MTRB logic. The actual situation differs from one board type to another.
Terminal O&M software includes Local Maintenance Function (LMF) software (i.e., the local O&M software), and O&M Center (OMC) software (i.e., the remote O&M software).
0
错误 表格结果无效
LMF software comprises PC self-contained Telnet and File Transfer Protocol (FTP) software, while OMC software is composed of BAM software and Client software.
1.1.1 BTS Operational Software
I. BOOT software
BOOT software serves to start the board. Before the delivery of the BTS3601C, the BOOTROM in every board has already been installed with BOOT software. BOOT software upgrade is usually realized by replacing the chip.
II. CPU software
CPU software is the core of system functions. It can be loaded in two ways:
l If there is no old-version software on the board, it is necessary to load the board
(in the commissioning mode) with the software through the board network port.
l If there is old-version software on the board, the software can be upgraded
through software loading by using local FTP software or remote O&M software.
III. FPGA logic
FPGA logic should be loaded to BTS3601C MBPB/MTRB. The loading mode is the same as that of CPU software.
1-1
Installation Manual iSiteC BTS3601C CDMA Base Station
&
Note:
The BTS operational software has been installed before delivery, so there is no need to install onsite. However, the operational software needs to be upgraded or re-loaded upon version upgrade. For details,
please refer to Chapter 3 BTS Operation Software Installation.
1.1.2 Terminal O&M Software
I. Local O&M software
The local maintenance console is a portable computer installed with Windows9x Operating System (OS), which contains the local O&M software. It includes FTP Client (Ftp.exe) and Telnet Client (Telnet.exe).
The BTS3601C objects, including sites, cells, basebands, carriers, channels, etc., can be maintained with local maintenance commands.
Software Installation & System Commissioning
0
错误 表格结果无效
Since the two programs (Ftp.exe and Telnet.exe) are provided by Windows9x OS, there is no need for extra installation.
II. Remote O&M software
Remote O&M software (OMC) of the Base Station Subsystem (BSS) adopts the Client/Server structure.
Through the Client, users can input operation commands, which are then processed by the server (BAM) in a centralized way. After the processing, these commands are transmitted to the foreground (including BSC and BTS), which will then return the operation result (success, failure, timeout, exception, etc.). BAM will record the result and transmit it in a certain report format to the Client.
With OMC, the user can perform remote maintenance and monitoring over all the BTSs that are under his control.
The collected site information can also be used for network planning. The installation of OMC software involves the installation of BAM server software and
the installation of the Client software. The Client software is divided into three kinds: BSC Client, BTS3612 Client and
BTS3601C Client. This manual describes the installation of BTS3601C Client software only. For the
installation of BAM server and other Client software, please refer to the corresponding installation manual.
1-2
Installation Manual iSiteC BTS3601C CDMA Base Station
Software Installation & System Commissioning
Table of Contents
Table of Contents
2.1 Software Features .....................................................................................................2-1
2.2 Installing Local O&M Software....................................................................................2-1
2.2.1 Operational Environment..................................................................................2-1
2.2.2 Conditions.......................................................................................................2-2
2.2.3 Network Configuration......................................................................................2-2
2.2.4 Software Installation and Instructions ................................................................2-3
2.3 Installing Remote O&M Software................................................................................2-3
2.3.1 Operational Environment..................................................................................2-3
2.3.2 Conditions.......................................................................................................2-3
2.3.3 Software Installation and Instructions ................................................................2-3
i
Installation Manual iSiteC BTS3601C CDMA Base Station
2 Installing BTS Terminal O&M Software
2.1 Software Features
BTS3601C terminal O&M software (hereinafter referred to as "terminal O&M software") is classified into two categories: the remote O&M and the local O&M. These two categories differ in the way they are installed.
I. Local O&M software
Local O&M software includes FTP Client (Ftp.exe) and Telnet Client (Telnet.exe). The two programs are both self-contained by Windows9x OS.
To realize the local maintenance, the maintenance console is connected through crossover network cables to BTS via the Ethernet port that is in the Micro-bts Base-band Processing Module (MBPM) maintenance window. The user thus can issue O&M commands through the local maintenance console to maintain the BTS3601C.
Software Installation & System Commissioning
0
错误 表格结果无效
II. Remote O&M software
The remote O&M software comprises the software for the BAM server and the Client. Among which, the Client software is composed of three parts: BSC Client, BTS3612 Client and BTS3601C Client. The remote O&M software described in this manual refers to BTS3601C Client.
2.2 Installing Local O&M Software
2.2.1 Operational Environment
I. Hardware environment
Basic hardware configuration of the WS (desk-top computer):
l Pentium 100 CPU l One 500Mbyte hard disk l One 8Mbyte memory l One integrated network card
2-1
Installation Manual iSiteC BTS3601C CDMA Base Station
II. Software configuration
Windows 95 or Windows 98.
2.2.2 Conditions
For the normal operation of the local maintenance console, the following conditions should be met:
1) The hardware environment are ready;
2) Windows9x OS can operate normally;
3) Windows9x installation files and network card driver (provided by the original manufacturer) are furnished.
2.2.3 Network Configuration
This involves the installation and configuration of the network card and the TCP/IP. The configuration is performed through the functional items of "Add new hardware" and "Network" in turn on the "Control Panel" of the computer.
Software Installation & System Commissioning
0
错误 表格结果无效
The IP address of the maintenance console should be in the same network segment as that of BTS3601C MBPM network port. In addition, the address should be unique in the IP addresses of the network equipment.
The connection sequence of network cables (crossover cable) at the network port is shown in Figure 2-1.
Green
Green
Green and white
Yellow and white
Green and white
Yellow and white
Blue
Blue
RJ45
RJ45
Blue and white
Yellow
Blown and white
Blue and white
Yellow
Blown and white
1
1
2
2
3
3
4
4 5
5 6
6 7
7 8
8
Blown
Blown
Yellow and white
Yellow
Green and white
Yellow and white
Yellow
Green and white
Blue
Blue
RJ45
RJ45
3
3 6
6 1
1 4
4 5
5 2
2 7
7 8
8
Blue and white
Green
Blown and white
Blue and white
Green
Blown and white
Blown
Blown
Figure 2-1 Connection sequence of crossover network cables
2-2
Installation Manual iSiteC BTS3601C CDMA Base Station
2.2.4 Software Installation and Instructions
Since Local O&M software (Ftp.exe and Telnet.exe) is self-contained by Windows9x, there is no need for extra installation.
To run Ftp/Telnet, click [Start/Run] in the system menu of the computer, and input "ftp xxx.xxx.xxx.xxx"/"telnet xxx.xxx.xxx.xxx" into the dialogue box of [Run]. "xxx.xxx.xxx.xxx" is the IP address of MBPM network port. Ftp/Telnet is then started for you to log in to the MBPM.
Software Installation & System Commissioning
0
错误 表格结果无效
2.3 Installing Remote O&M Software
2.3.1 Operational Environment
The remote O&M software (referring to the BTS3601C Client software here) should be installed to the same computer together with BSC Client and BTS3612 Client.
2.3.2 Conditions
1) Make sure the computer is installed with only the software necessary for the system. Otherwise, there may be operational conflicts that may affect the normal operation of the Client software. Moreover, make sure that a nice and stable network hardware environment has been established.
2) Obtain from Huawei the complete set of installation files and read-me files, as well as a legal product serial number.
3) BTS3601C Client software should be insta lled only after the corresponding BSC Client and BTS3612 Client have been installed. Before installation, please make sure that the versions of the three kinds of software are consistent.
2.3.3 Software Installation and Instructions
The BSC Client and BTS3612 Client (both are of the matching versions) should have been installed first (for instructions, please refer to the corresponding parts in BSC/BTS3612 installation manuals). After that, to install BTS3601C Client software, the procedures include:
I. Starting SETUP.EXE
After inserting the installation disk into the disk drive, different alternatives are provided for:
l If auto execution has been set for the system, the program will be started then. l Or, you should click [Start/Run] in the system menu and key in "SETUP" and the
corresponding driver icon and path, and press <Enter>.
2-3
Installation Manual iSiteC BTS3601C CDMA Base Station
l You can also click [SETUP.EXE] in the Resource Manager to run the program. l You can copy the files in the installation disk to the hard disk and run them.
The initial installation interface as shown in Figure 2-2 will then pop up.
Software Installation & System Commissioning
0
错误 表格结果无效
Figure 2-2 Initial installation interface
Click <Next> to continue (or click <Cancel> to exit the installation).
II. License agreement and installation instructions
The [Software License Agreement] will pop up as shown in Figure 2-3. After reading it carefully, click <Yes> to accept it and continue (or <No> to exit the installation).
2-4
Installation Manual iSiteC BTS3601C CDMA Base Station
Software Installation & System Commissioning
0
错误 表格结果无效
Figure 2-3 Software license agreement interface
The installation wizard will guide you how to install the software step by step, as shown in Figure 2-4. It may contain some latest installation information not given in this manual. Read the information carefully, then click <Next> to continue.
Figure 2-4 Interface of system installation instructions
2-5
Installation Manual iSiteC BTS3601C CDMA Base Station
III. Confirming the installation information
You are required to confirm the installation information as shown in Figure 2-5 before copying files.
If you want to change the installation information, please click <Back> to return to the previous step. Otherwise, click <Next> to continue.
Software Installation & System Commissioning
0
错误 表格结果无效
Figure 2-5 Confirming the installation information
&
Note:
The default installation path for BTS3601C Client software is D:\AirBridge, the same as that of BSC Client and BTS3612 Client. If the installation path of BSC/BTS3612 Client has been changed, the
installation program of BTS3601C Client will automatically find the new one.
IV. Completing the installation
After confirming the installation information, the installation program will start copying files. In the process of file copying, the installation program will show such information including overall progress, available disk space, available memory and progress of individual file copying.
Upon the completion of the installation, the window [Setup Complete] as shown in Figure 2-6 will pop up.
2-6
Loading...
+ 28 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use