Huawei B68L 54 User Manual
B68L Wireless Gateway
Quick Start
1 Getting to know your B68L
Power button
Press and hold for about 3 seconds to power the
B68L on or off.
WPS button
LAN port Connect to computer, switch, or other LAN device.
Power port Connect to compatible power adapter.
Telephone port Connect to telephone.
Press and hold for 3 or more seconds to active WPS
connection when Wi-Fi is turned on.
2
Fast red blinking: no SIM/USIM card is found, the
PIN is not verified, or the SIM/USIM card is not
working properly.
Steady yellow: registered with a 3G/2G network.
Steady green: connected to the Internet.
Off: no signal.
Steady on: Wi-Fi turned on or data transfer in
progress.
Blinking: a WPS connection is being set up.
Off: Wi-Fi turned off.
On: the B68L is powered on.
Off: the B68L is powered off.
Steady on: LAN port is connected to a client.
Off: no client is connected to LAN port.
Install a SIM/USIM card to access to the Internet via
a 3G/2G data connection.
Restoring the default settings of the B68L will erase
all previous settings.
Network mode
indicator
Wi-Fi/WPS
indicator
Power indicator
/
LAN indicator
SIM/USIM card
slot
When the B68L is powered on, use a sharply pointed
Reset button
object to press and hold for about 3 seconds until all
indicators are blinking to restore the B68L to its
factory settings. After the factory defaults are
restored, the B68L will restart automatically.
3
2 Installation
Reset
Installing the SIM/USIM card
1. Slide off the card slot cover.
2. Insert the SIM/USIM card into the card slot. Ensure that the beveled edge of the
SIM/USIM card aligns with that of the card slot.
3. Close the card slot cover.
Before removing the SIM/USIM card, ensure that the B68L is powered off and
disconnected from the power outlet.
(Optional) Installing the table stand
The table stand is an optional accessory, and may not included in the packaging box.
If required, please contact your local dealer purchase it.
You can place the B68L on a flat surface such as a table or a desk, or hang it on a wall.
You can also use the table stand of the B68L to place it upright.
Insert the latches into the table stand slots on the bottom of the B68L.
4
Connecting cables
To prevent interference caused by radio signals, place the B68L at least 1 meter (3.28
feet) away from telephone and other electrical devices.
Once connected to a power outlet, the B68L automatically powers on.
Power adapter
Computer
Do not connect the B68L to the telephone wall outlet (or any Public Switched
Telephone Network), because doing so could damage the B68L due to excessive heat.
Telephone
Laptop, tablet, or smart phone
5
3 Setting up a Wi-Fi connection
Make sure your client (computer, tablet, or smart phone) also supports Wi-Fi.
Turning on Wi-Fi on the B68L
When the indicator is steady on, the Wi-Fi of the B68L is turned on.
To manually turn Wi-Fi on, log in to the web management page (default address:
http://192.168.1.1, default password: admin), and choose Home Network >
WLAN Settings. On the displayed page, select Enable WLAN 2.4 GHz and click
Save.
Recording the SSID and Wi-Fi key
The default SSID and Wi-Fi key are printed on the B68L's rear label.
To prevent unauthorized parties from accessing your wireless network, it is
recommended that you change the SSID and Wi-F i key from time to time . Log in to
the web management page (default address: http://192.168.1.1, default password:
admin), choose Home and click Set Up WLAN to set WLAN 2.4 GHz SSID and
Password.
6
Loading...