Page 1
HP StorageWorks 600 Modular Disk System
Maintenance and Service Guide
Part Number 495106-005
December 2009 (Fifth Edition)
Page 2
© Copyright 2008, 2009 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP
shall not be liable for technical or editorial errors or omissions contained herein.
Windows is a U.S. registered trademarks of Microsoft Corporation.
Intended audience
This document is for the person who installs, administers, and troubleshoots servers and storage systems.
HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards
in products with hazardous energy levels.
Page 3
Contents
Customer self repair ...................................................................................................................... 5
Parts only warranty service ............................................................................................................................ 5
Illustrated parts catalog ............................................................................................................... 16
Mechanical components ............................................................................................................................. 16
System components .................................................................................................................................... 19
Removal and replacement procedures ........................................................................................... 23
Required tools ............................................................................................................................................ 23
Safety considerations .................................................................................................................................. 23
Preventing electrostatic discharge ...................................................................................................... 23
Warning and caution messages ........................................................................................................ 23
Power down .............................................................................................................................................. 25
Extend the hard drive drawer ...................................................................................................................... 25
Hard drive blank ........................................................................................................................................ 26
Hard drive ................................................................................................................................................. 27
Hard drive drawer bezel ............................................................................................................................. 28
Hard drive drawer display board ................................................................................................................ 29
Fan ........................................................................................................................................................... 31
Hot-plug I/O module .................................................................................................................................. 32
Power supply ............................................................................................................................................. 33
Hard drive drawer ..................................................................................................................................... 34
Power block............................................................................................................................................... 39
Fan board ................................................................................................................................................. 40
Dual 7-segment display board ..................................................................................................................... 42
Power button/UID board ............................................................................................................................. 43
Cable management arm ............................................................................................................................. 44
Diagnostic tools .......................................................................................................................... 49
Integrated Management Log ........................................................................................................................ 49
Array Diagnostic Utility ............................................................................................................................... 49
Array Configuration Utility .......................................................................................................................... 49
Component identification ............................................................................................................. 51
Front panel components .............................................................................................................................. 51
Diagnostic cable access .................................................................................................................... 51
Front panel LEDs and button ........................................................................................................................ 53
Rear panel components .............................................................................................................................. 55
Rear panel LEDs and buttons ....................................................................................................................... 56
Device bay ID numbers ............................................................................................................................... 57
SAS and SATA hard drive LEDs ................................................................................................................... 58
SAS and SATA hard drive LED combinations ................................................................................................ 58
Specifications ............................................................................................................................. 60
Environmental specifications ........................................................................................................................ 60
Storage array specifications ........................................................................................................................ 60
Acronyms and abbreviations ........................................................................................................ 61
Page 4
Index ......................................................................................................................................... 62
Page 5
Customer self repair
HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow
for greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP
service providers or service partners) identifies that the repair can be accomplished by the use of a CSR
part, HP will ship that part directly to you for replacement. There are two categories of CSR parts:
• Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these
parts, you will be charged for the travel and labor costs of this service.
• Optional—Parts for which customer self repair is optional. These parts are also designed for
customer self repair. If, however, you require that HP replace them for you, there may or may not be
additional charges, depending on the type of warranty service designated for your product.
NOTE: Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty,
HP requires that an authorized service provider replace the part. These parts are identified as "No" in the
Illustrated Parts Catalog.
Based on availability and where geography permits, CSR parts will be shipped for next business day
delivery. Same day or four-hour delivery may be offered at an additional charge where geography
permits. If assistance is required, you can call the HP Technical Support Center and a technician will help
you over the telephone. HP specifies in the materials shipped with a replacement CSR part whether a
defective part must be returned to HP. In cases where it is required to return the defective part to HP, you
must ship the defective part back to HP within a defined period of time, normally five (5) business days.
The defective part must be returned with the associated documentation in the provided shipping material.
Failure to return the defective part may result in HP billing you for the replacement. With a customer self
repair, HP will pay all shipping and part return costs and determine the courier/carrier to be used.
For more information about HP's Customer Self Repair program, contact your local service provider. For
the North American program, refer to the HP website (http://www.hp.com/go/selfrepair
Parts only warranty service
Your HP Limited Warranty may include a parts only warranty service. Under the terms of parts only
warranty service, HP will provide replacement parts free of charge.
For parts only warranty service, CSR part replacement is mandatory. If you request HP to replace these
parts, you will be charged for the travel and labor costs of this service.
).
Réparation par le client (CSR)
Les produits HP comportent de nombreuses pièces CSR (Customer Self Repair = réparation par le client)
afin de minimiser les délais de réparation et faciliter le remplacement des pièces défectueuses. Si pendant
la période de diagnostic, HP (ou ses partenaires ou mainteneurs agréés) détermine que la réparation peut
être effectuée à l'aide d'une pièce CSR, HP vous l'envoie directement. Il existe deux catégories de pièces
CSR:
Customer self repair 5
Page 6
Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de
remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
Facultatif - Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également
conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous demandez à HP de
remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type de garantie applicable à
votre produit.
REMARQUE: Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la
réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention "Non" dans le Catalogue
illustré.
Les pièces CSR sont livrées le jour ouvré suivant, dans la limite des stocks disponibles et selon votre
situation géographique. Si votre situation géographique le permet et que vous demandez une livraison le
jour même ou dans les 4 heures, celle-ci vous sera facturée. Pour bénéficier d'une assistance
téléphonique, appelez le Centre d'assistance technique HP. Dans les documents envoyés avec la pièce de
rechange CSR, HP précise s'il est nécessaire de lui retourner la pièce défectueuse. Si c'est le cas, vous
devez le faire dans le délai indiqué, généralement cinq (5) jours ouvrés. La pièce et sa documentation
doivent être retournées dans l'emballage fourni. Si vous ne retournez pas la pièce défectueuse, HP se
réserve le droit de vous facturer les coûts de remplacement. Dans le cas d'une pièce CSR, HP supporte
l'ensemble des frais d'expédition et de retour, et détermine la société de courses ou le transporteur à
utiliser.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus
d'informations sur ce programme en Amérique du Nord, consultez le site Web HP
(http://www.hp.com/go/selfrepair
).
Service de garantie "pièces seules"
Votre garantie limitée HP peut inclure un service de garantie "pièces seules". Dans ce cas, les pièces de
rechange fournies par HP ne sont pas facturées.
Dans le cadre de ce service, la réparation des pièces CSR par le client est obligatoire. Si vous demandez
à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
Riparazione da parte del cliente
Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti
difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente
dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di servizi o di
assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo spedirà direttamente
al cliente per la sostituzione. Vi sono due categorie di parti CSR:
Obbligatorie – Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida la
riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio.
Opzionali – Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di componenti
progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP, potrebbe dover
sostenere spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
Customer self repair 6
Page 7
NOTA: alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare
la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti
sono identificate da un "No" nel Catalogo illustrato dei componenti.
In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro il
giorno lavorativo seguente. La consegna nel giorno stesso o entro quattro ore è offerta con un
supplemento di costo solo in alcune zone. In caso di necessità si può richiedere l'assistenza telefonica di
un addetto del centro di supporto tecnico HP. Nel materiale fornito con una parte di ricambio CSR, HP
specifica se il cliente deve restituire dei componenti. Qualora sia richiesta la resa ad HP del componente
difettoso, lo si deve spedire ad HP entro un determinato periodo di tempo, generalmente cinque (5) giorni
lavorativi. Il componente difettoso deve essere restituito con la documentazione associata nell'imballo di
spedizione fornito. La mancata restituzione del componente può comportare la fatturazione del ricambio
da parte di HP. Nel caso di riparazione da parte del cliente, HP sostiene tutte le spese di spedizione e
resa e sceglie il corriere/vettore da utilizzare.
Per ulteriori informazioni sul programma CSR di HP contattare il centro di assistenza di zona. Per il
programma in Nord America fare riferimento al sito Web HP (http://www.hp.com/go/selfrepair
Servizio di garanzia per i soli componenti
La garanzia limitata HP può includere un servizio di garanzia per i soli componenti. Nei termini di
garanzia del servizio per i soli componenti, HP fornirà gratuitamente le parti di ricambio.
).
Per il servizio di garanzia per i soli componenti è obbligatoria la formula CSR che prevede la riparazione
da parte del cliente. Se il cliente invece richiede la sostituzione ad HP, dovrà sostenere le spese di
spedizione e di manodopera per il servizio.
Customer Self Repair
HP Produkte enthalten viele CSR-Teile (Customer Self Repair), um Reparaturzeiten zu minimieren und
höhere Flexibilität beim Austausch defekter Bauteile zu ermöglichen. Wenn HP (oder ein HP
Servicepartner) bei der Diagnose feststellt, dass das Produkt mithilfe eines CSR-Teils repariert werden
kann, sendet Ihnen HP dieses Bauteil zum Austausch direkt zu. CSR-Teile werden in zwei Kategorien
unterteilt:
Zwingend – Teile, für die das Customer Self Repair-Verfahren zwingend vorgegeben ist. Wenn Sie den
Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und Arbeitskosten für diesen
Service berechnet.
Optional – Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für
Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen lassen
möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen
zusätzliche Kosten anfallen.
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog
sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag
geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen
einen Aufpreis verfügbar. Wenn Sie Hilfe benötigen, können Sie das HP technische Support Center
Customer self repair 7
Page 8
anrufen und sich von einem Mitarbeiter per Telefon helfen lassen. Den Materialien, die mit einem CSRErsatzteil geliefert werden, können Sie entnehmen, ob das defekte Teil an HP zurückgeschickt werden
muss. Wenn es erforderlich ist, das defekte Teil an HP zurückzuschicken, müssen Sie dies innerhalb eines
vorgegebenen Zeitraums tun, in der Regel innerhalb von fünf (5) Geschäftstagen. Das defekte Teil muss
mit der zugehörigen Dokumentation in der Verpackung zurückgeschickt werden, die im Lieferumfang
enthalten ist. Wenn Sie das defekte Teil nicht zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung
stellen. Im Falle von Customer Self Repair kommt HP für alle Kosten für die Lieferung und Rücksendung auf
und bestimmt den Kurier-/Frachtdienst.
Weitere Informationen über das HP Customer Self Repair Programm erhalten Sie von Ihrem Servicepartner
vor Ort. Informationen über das CSR-Programm in Nordamerika finden Sie auf der HP Website unter
(http://www.hp.com/go/selfrepair
).
Parts-only Warranty Service (Garantieservice
ausschließlich für Teile)
Ihre HP Garantie umfasst möglicherweise einen Parts-only Warranty Service (Garantieservice
ausschließlich für Teile). Gemäß den Bestimmungen des Parts-only Warranty Service stellt HP Ersatzteile
kostenlos zur Verfügung.
Für den Parts-only Warranty Service ist das CSR-Verfahren zwingend vorgegeben. Wenn Sie den
Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und Arbeitskosten für diesen
Service berechnet.
Reparaciones del propio cliente
Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar (Customer
Self Repair, CSR) para minimizar el tiempo de reparación y ofrecer una mayor flexibilidad a la hora de
realizar sustituciones de componentes defectuosos. Si, durante la fase de diagnóstico, HP (o los
proveedores o socios de servicio de HP) identifica que una reparación puede llevarse a cabo mediante el
uso de un componente CSR, HP le enviará dicho componente directamente para que realice su
sustitución. Los componentes CSR se clasifican en dos categorías:
• Obligatorio: componentes para los que la reparación por parte del usuario es obligatoria. Si solicita
a HP que realice la sustitución de estos componentes, tendrá que hacerse cargo de los gastos de
desplazamiento y de mano de obra de dicho servicio.
• Opcional: componentes para los que la reparación por parte del usuario es opcional. Estos
componentes también están diseñados para que puedan ser reparados por el usuario. Sin embargo,
si precisa que HP realice su sustitución, puede o no conllevar costes adicionales, dependiendo del
tipo de servicio de garantía correspondiente al producto.
NOTA: Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para
que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la palabra
"No" en el catálogo ilustrado de componentes.
Según la disponibilidad y la situación geográfica, los componentes CSR se enviarán para que lleguen a
su destino al siguiente día laborable. Si la situación geográfica lo permite, se puede solicitar la entrega
en el mismo día o en cuatro horas con un coste adicional. Si precisa asistencia técnica, puede llamar al
Customer self repair 8
Page 9
Centro de asistencia técnica de HP y recibirá ayuda telefónica por parte de un técnico. Con el envío de
materiales para la sustitución de componentes CSR, HP especificará si los componentes defectuosos
deberán devolverse a HP. En aquellos casos en los que sea necesario devolver algún componente a HP,
deberá hacerlo en el periodo de tiempo especificado, normalmente cinco días laborables. Los
componentes defectuosos deberán devolverse con toda la documentación relacionada y con el embalaje
de envío. Si no enviara el componente defectuoso requerido, HP podrá cobrarle por el de sustitución. En
el caso de todas sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío
y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio.
Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase
en contacto con su proveedor de servicios local. Si está interesado en el programa para Norteamérica,
visite la página web de HP siguiente (http://www.hp.com/go/selfrepair
).
Servicio de garantía exclusivo de componentes
La garantía limitada de HP puede que incluya un servicio de garantía exclusivo de componentes. Según
las condiciones de este servicio exclusivo de componentes, HP le facilitará los componentes de repuesto
sin cargo adicional alguno.
Para este servicio de garantía exclusivo de componentes, es obligatoria la sustitución de componentes
por parte del usuario (CSR). Si solicita a HP que realice la sustitución de estos componentes, tendrá que
hacerse cargo de los gastos de desplazamiento y de mano de obra de dicho servicio.
Customer Self Repair
Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot een
minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is. Deze
onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd. Als HP (of een HP Service Partner)
bij de diagnose vaststelt dat de reparatie kan worden uitgevoerd met een CSR-onderdeel, verzendt HP
dat onderdeel rechtstreeks naar u, zodat u het defecte onderdeel daarmee kunt vervangen. Er zijn twee
categorieën CSR-onderdelen:
Verplicht: Onderdelen waarvoor reparatie door de klant verplicht is. Als u HP verzoekt deze onderdelen
voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in rekening gebracht.
Optioneel: Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn
ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen,
kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor
het product.
OPMERKING: Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband met
de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden vervangen.
Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee".
Afhankelijk van de leverbaarheid en de locatie worden CSR-onderdelen verzonden voor levering op de
eerstvolgende werkdag. Levering op dezelfde dag of binnen vier uur kan tegen meerkosten worden
aangeboden, indien dit mogelijk is gezien de locatie. Indien assistentie gewenst is, belt u een HP Service
Partner om via de telefoon technische ondersteuning te ontvangen. HP vermeldt in de documentatie bij het
vervangende CSR-onderdeel of het defecte onderdeel aan HP moet worden geretourneerd. Als het defecte
onderdeel aan HP moet worden teruggezonden, moet u het defecte onderdeel binnen een bepaalde
periode, gewoonlijk vijf (5) werkdagen, retourneren aan HP. Het defecte onderdeel moet met de
Customer self repair 9
Page 10
bijbehorende documentatie worden geretourneerd in het meegeleverde verpakkingsmateriaal. Als u het
defecte onderdeel niet terugzendt, kan HP u voor het vervangende onderdeel kosten in rekening brengen.
Bij reparatie door de klant betaalt HP alle verzendkosten voor het vervangende en geretourneerde
onderdeel en kiest HP zelf welke koerier/transportonderneming hiervoor wordt gebruikt.
Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair programma
van HP. Informatie over Service Partners vindt u op de HP website (http://www.hp.com/go/selfrepair
Garantieservice "Parts Only"
Het is mogelijk dat de HP garantie alleen de garantieservice "Parts Only" omvat. Volgens de bepalingen
van de Parts Only garantieservice zal HP kosteloos vervangende onderdelen ter beschikking stellen.
Voor de Parts Only garantieservice is vervanging door CSR-onderdelen verplicht. Als u HP verzoekt deze
onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in rekening
gebracht.
Reparo feito pelo cliente
).
Os produtos da HP são projetados com muitas peças para reparo feito pelo cliente (CSR) de modo a
minimizar o tempo de reparo e permitir maior flexibilidade na substituição de peças com defeito. Se,
durante o período de diagnóstico, a HP (ou fornecedores/parceiros de serviço da HP) concluir que o
reparo pode ser efetuado pelo uso de uma peça CSR, a peça de reposição será enviada diretamente ao
cliente. Existem duas categorias de peças CSR:
Obrigatória – Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas
peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o
reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança
de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de
cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças estão
identificadas com a marca "No" (Não), no catálogo de peças ilustrado.
Conforme a disponibilidade e o local geográfico, as peças CSR serão enviadas no primeiro dia útil após
o pedido. Onde as condições geográficas permitirem, a entrega no mesmo dia ou em quatro horas pode
ser feita mediante uma taxa adicional. Se precisar de auxílio, entre em contato com o Centro de suporte
técnico da HP para que um técnico o ajude por telefone. A HP especifica nos materiais fornecidos com a
peça CSR de reposição se a peça com defeito deve ser devolvida à HP. Nos casos em que isso for
necessário, é preciso enviar a peça com defeito à HP dentro do período determinado, normalmente
cinco (5) dias úteis. A peça com defeito deve ser enviada com a documentação correspondente no
material de transporte fornecido. Caso não o faça, a HP poderá cobrar a reposição. Para as peças de
reparo feito pelo cliente, a HP paga todas as despesas de transporte e de devolução da peça e
determina a transportadora/serviço postal a ser utilizado.
Para obter mais informações sobre o programa de reparo feito pelo cliente da HP, entre em contato com
o fornecedor de serviços local. Para o programa norte-americano, visite o site da HP
(http://www.hp.com/go/selfrepair
).
Customer self repair 10
Page 11
Serviço de garantia apenas para peças
A garantia limitada da HP pode incluir um serviço de garantia apenas para peças. Segundo os termos
do serviço de garantia apenas para peças, a HP fornece as peças de reposição sem cobrar nenhuma
taxa.
No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP substitua essas
peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
Customer self repair 11
Page 12
Customer self repair 12
Page 13
Customer self repair 13
Page 14
Customer self repair 14
Page 15
Customer self repair 15
Page 16
Illustrated parts catalog
Mechanical components
Item Description Spare part number
Customer self repair (on
page 5)
1 Chassis — —
2 Internal rail kit 455980-001 No3
3 Hard drive drawer bezel 455973-001 Optional2
1
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be
charged for the travel and labor costs of this service.
2
Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If,
however, you require that HP replace them for you, there may or may not be additional charges, depending on the
type of warranty service designated for your product.
3
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty, HP requires
that an authorized service provider replace the part. These parts are identified as "No" in the Illustrated Parts
Catalog.
1
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP
de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
2
Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également
conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous demandez à HP de remplacer
ces pièces, l'intervention peut ou non vous être facturée, selon le type de garantie applicable à votre produit.
3
No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la réparation. Pour
que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit effectué par un Mainteneur Agréé.
Ces pièces sont identifiées par la mention “Non” dans le Catalogue illustré.
1
Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida la
riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio.
Illustrated parts catalog 16
Page 17
2
Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di componenti
progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP, potrebbe dover sostenere spese
addizionali a seconda del tipo di garanzia previsto per il prodotto.
3
No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare la
garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti sono
identificate da un “No” nel Catalogo illustrato dei componenti.
1
Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden müssen. Wenn
Sie diese Teile von HP ersetzen lassen, werden Ihnen die Versand- und Arbeitskosten für diesen Service berechnet.
2
Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für
Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen lassen möchten,
können bei diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche Kosten
anfallen.
3
No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu
erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit
„No“ bzw. „Nein“ gekennzeichnet.
1
Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es obligatoria. Si solicita a
HP que realice la sustitución de estos componentes, tendrá que hacerse cargo de los gastos de desplazamiento y de
mano de obra de dicho servicio.
2
Optional: Opcional— componentes para los que la reparación por parte del usuario es opcional. Estos
componentes también están diseñados para que puedan ser reparados por el usuario. Sin embargo, si precisa que
HP realice su sustitución, puede o no conllevar costes adicionales, dependiendo del tipo de servicio de garantía
correspondiente al producto.
3
No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para que el
usuario haga valer su garantía, HP pone como condición que un proveedor de servicios autorizado realice la
sustitución de estos componentes. Dichos componentes se identifican con la palabra “No” en el catálogo ilustrado de
componentes.
1
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt deze onderdelen
te vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
2
Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn
ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen, kunnen
daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor het product.
3
No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband met de
garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden vervangen. Deze
onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee".
1
Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas
peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
2
Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o
reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa
adicional, dependendo do tipo de serviço de garantia destinado ao produto.
3
No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de cumprir a
garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças estão identificadas com a
marca “No” (Não), no catálogo de peças ilustrado.
Illustrated parts catalog 17
Page 18
Illustrated parts catalog 18
Page 19
System components
Item Description Spare part number
4 I/O module with tray and cable 498472-001 Mandatory1
5 Fan 413996-001 Mandatory1
6 Power supply 441830-001 Mandatory1
7 Power block board kit 455975-001 Optional2
8 Power block assembly 455974-001 Optional2
a) UID/power switch board with cables — —
b) Dual 7-segment display board with
cables
Customer self repair (on
page 5)
— —
Illustrated parts catalog 19
Page 20
Item Description Spare part number
Customer self repair (on
page 5)
9 Fan power board with cables 455977-001 No3
10
11 Extension arm with cables 455978-001 No3
12 LED display board with cable 455979-001 Optional2
13 Rackmount kit* 432461-001 Mandatory1
14 Hard drive blank* 389015-001 Mandatory1
15 Hard drive* — Mandatory1
a) UID/power switch board — —
b) Dual 7-segment display board — —
c) Power supply boards — —
d) Power supply/7-segment ribbon
— —
cable
e) Crossover cable — —
f) I/O cage assembly — —
g) Power/UID bezel assembly — —
h) 7-segment rear bezel — —
Hard drive drawer with hard drive
455976-001 No3
backplane and cables
a) 146-GB, SAS, SFF, 15,000-rpm,
488058-001 —
dual-port
b) 300-GB, SAS, SFF, 15,000-rpm,
488060-001 —
dual-port
c) 450-GB, SAS, SFF, 15,000-rpm,
454274-001 —
dual-port
d) 750-GB, SAS, SFF, 15,000-rpm,
461288-001 —
dual-port, MDL
e) 1-TB, SAS, SFF, 7,200-rpm, dual-
461289-001 —
port, MDL
f) 300-GB, 6G, SAS, 15,000-rpm 517350-001 —
g) 450GB, 6G, SAS, 15,000-rpm 517352-001 —
h) 600GB, 6G, SAS, 15,000-rpm 517354-001 —
i) 500-GB, 3G, SATA, 7,200-rpm 459319-001 —
j) 750-GB, 3G, SATA, 7,200-rpm 459320-001 —
k) 1-TB, 3G, SATA, 7,200-rpm, MDL 454273-001 —
* Not shown
1
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be
charged for the travel and labor costs of this service.
2
Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If,
however, you require that HP replace them for you, there may or may not be additional charges, depending on the
type of warranty service designated for your product.
Illustrated parts catalog 20
Page 21
3
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty, HP requires
that an authorized service provider replace the part. These parts are identified as "No" in the Illustrated Parts
Catalog.
1
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP
de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
2
Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également
conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous demandez à HP de remplacer
ces pièces, l'intervention peut ou non vous être facturée, selon le type de garantie applicable à votre produit.
3
No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la réparation. Pour
que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit effectué par un Mainteneur Agréé.
Ces pièces sont identifiées par la mention “Non” dans le Catalogue illustré.
1
Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida la
riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio.
2
Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di componenti
progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP, potrebbe dover sostenere spese
addizionali a seconda del tipo di garanzia previsto per il prodotto.
3
No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare la
garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti sono
identificate da un “No” nel Catalogo illustrato dei componenti.
1
Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden müssen. Wenn
Sie diese Teile von HP ersetzen lassen, werden Ihnen die Versand- und Arbeitskosten für diesen Service berechnet.
2
Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für
Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen lassen möchten,
können bei diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche Kosten
anfallen.
3
No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu
erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit
„No“ bzw. „Nein“ gekennzeichnet.
1
Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es obligatoria. Si solicita a
HP que realice la sustitución de estos componentes, tendrá que hacerse cargo de los gastos de desplazamiento y de
mano de obra de dicho servicio.
2
Optional: Opcional— componentes para los que la reparación por parte del usuario es opcional. Estos
componentes también están diseñados para que puedan ser reparados por el usuario. Sin embargo, si precisa que
HP realice su sustitución, puede o no conllevar costes adicionales, dependiendo del tipo de servicio de garantía
correspondiente al producto.
3
No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para que el
usuario haga valer su garantía, HP pone como condición que un proveedor de servicios autorizado realice la
sustitución de estos componentes. Dichos componentes se identifican con la palabra “No” en el catálogo ilustrado de
componentes.
1
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt deze onderdelen
te vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
2
Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn
ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen, kunnen
daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor het product.
3
No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband met de
garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden vervangen. Deze
onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee".
1
Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas
peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
Illustrated parts catalog 21
Page 22
2
Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o
reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa
adicional, dependendo do tipo de serviço de garantia destinado ao produto.
3
No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de cumprir a
garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças estão identificadas com a
marca “No” (Não), no catálogo de peças ilustrado.
Illustrated parts catalog 22
Page 23
Removal and replacement procedures
Required tools
The following items are required for some procedures:
• T-8 Torx screwdriver
• T-10 Torx screwdriver
• T-15 Torx screwdriver
• Phillips screwdriver
Safety considerations
Preventing electrostatic discharge
Before performing service procedures, review all the safety information.
To prevent damaging the system, be aware of the precautions you need to follow when setting up the
system or handling parts. A discharge of static electricity from a finger or other conductor may damage
system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the
device.
To prevent electrostatic damage:
• Avoid hand contact by transporting and storing products in static-safe containers.
• Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
• Place parts on a grounded surface before removing them from their containers.
• Avoid touching pins, leads, or circuitry.
• Always be properly grounded when touching a static-sensitive component or assembly.
Warning and caution messages
WARNING: To reduce the risk of personal injury or damage to equipment, heed all warnings
and cautions throughout the installation instructions.
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:
• The leveling jacks are extended to the floor.
• The full weight of the rack rests on the leveling jacks.
• The stabilizing feet are attached to the rack if it is a single-rack installation.
• The racks are coupled together in multiple-rack installations.
• Only one component is extended at a time. A rack may become unstable if more than one
component is extended for any reason.
Removal and replacement procedures 23
Page 24
WARNING: To reduce the risk of personal injury or equipment damage when unloading a
rack:
• At least two people are needed to safely unload the rack from the pallet. An empty 42U
rack can weigh as much as 115 kg (253 lb), can stand more than 2.1 m (7 ft) tall, and
may become unstable when being moved on its casters.
• Never stand in front of the rack when it is rolling down the ramp from the pallet. Always
handle the rack from both sides.
WARNING: The HP MDS600 Disk System is very heavy. To reduce the risk of personal injury
or damage to the equipment:
• Observe local occupational health and safety requirements and guidelines for manual
material handling.
• Remove all hard drives before installing or moving the HP MDS600 Disk Systems.
• Use caution and get help to lift and stabilize HP MDS600 Disk Systems during installation
or removal, especially when the HP MDS600 Disk System is not fastened to the rack.
• Never stack an HP MDS600 Disk System on top of another HP MDS600 Disk System.
• Never place equipment on top of an HP MDS600 Disk System.
• Never place an HP MDS600 Disk System on a surface that cannot support up to 163.3 kg
(360.0 lb).
WARNING: To reduce the risk of personal injury or damage to the equipment, you must
adequately support enclosures during installation and removal.
WARNING: Always use at least two people to lift an enclosure into the rack. If the enclosure
is being loaded into the rack above chest level, a third person must assist with aligning the
enclosure with the rails while the other two people support the weight of the enclosure.
WARNING: Be sure to install enclosures starting from the bottom of the rack and work your
way up the rack.
These symbols, on power supplies or systems, indicate that the equipment is
supplied by multiple sources of power.
WARNING: To reduce the risk of injury from electric shock, remove all power cords
to completely disconnect power from the system.
• Each enclosure has two or more power supply cords. A single rack or cabinet
may contain more than one enclosure. Power may be supplied in a redundant
fashion. Removing any single source of power does not necessarily remove
power from any portion of the system. When performing any service other than
hot-plug module replacement, you must completely disconnect all power to that
portion of the system.
• When performing service procedures on enclosures, shut off the circuit breakers
to both A and B AC power feeds and then disconnect all power cords from the
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
outlets before servicing.
internal system components to cool before touching them.
Removal and replacement procedures 24
Page 25
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Never reach inside the chassis while the system is powered up.
• Perform service on system components only as instructed in the user documentation.
WARNING: A risk of electric shock from high leakage current exists. Before connecting the
AC supply to the power enclosures, be sure that the electrical outlets are properly grounded
(earthed).
CAUTION: Always be sure that equipment is properly grounded and that you follow proper
grounding procedures before beginning any installation procedure. Improper grounding can
result in ESD damage to electronic components. For more information, see "Preventing
electrostatic discharge (on page 23)."
CAUTION: When performing non-hot-plug operations, you must power down the server blade
and/or the system. Use caution when performing other operations, such as hot-plug
installations or troubleshooting.
CAUTION: Protect the equipment from AC power fluctuations and temporary interruptions
with a regulating facility UPS device. This device protects the hardware from damage caused
by power surges and voltage spikes and keeps the system in operation during a power
failure.
Power down
Be sure that the partner server blades are the first units to be powered down and the last to be powered
back up. Taking this precaution ensures that the system and the OS are shut down in an orderly manner.
IMPORTANT: If installing a hot-plug device, it is not necessary to power down the MDS600.
To power down the MDS600:
1. Power down the partner server blades. See the server blade documentation.
2. Press and hold the Power On/Standby button for approximately 4 seconds. This action powers
down both hard drive drawers.
Extend the hard drive drawer
1. Be sure all I/O bays contain either an I/O module or an I/O blank. The hard drive drawer does not
open if I/O bays are empty.
2. Be sure the I/O modules or I/O blanks are fully seated and their handles are in the locked position.
The hard drive drawer does not open if I/O modules or I/O blanks are not fully seated with their
handles in the locked position.
WARNING: TIP HAZARD! To reduce the risk of personal injury or damage to the equipment,
do not extend the hard drive drawers beyond the supporting surface when the unit is not
installed in a rack.
WARNING: To reduce the risk of personal injury or damage to the equipment, ensure that
only one hard drive drawer is extended at a time.
Removal and replacement procedures 25
Page 26
WARNING: To reduce the risk of personal injury or damage to the equipment, you must
adequately support the chassis during installation and removal. It is not secured to the rack
3. Extend the hard drive drawer.
frame or mounted on rails.
WARNING: Pinch hazard—Keep hands out of front and rear of chassis when closing hard
drive drawers.
CAUTION: To prevent improper cooling and thermal damage, do not operate the MDS600
for an extended period of time with the drawer open.
Hard drive blank
CAUTION: To prevent improper cooling and thermal damage, do not operate the MDS600
unless all bays are populated with either a component or a blank. Remove a blank only when
To remove the component:
1. Extend the hard drive drawer (on page 25).
there is a drive ready to install or the MDS600 is powered down.
Removal and replacement procedures 26
Page 27
2.
Remove the hard drive blank.
To replace the blank, slide the blank into the bay until it locks into place.
Hard drive
CAUTION: To prevent improper cooling and thermal damage, do not operate the MDS600
unless all bays are populated with either a component or a blank. Remove a drive only when
Before replacing a hard drive, do the following:
• Verify the status of the drive to be replaced by reviewing the SAS and SATA hard drive LEDs (on
• Check the RAID status and configuration to be sure data loss will not occur if the drive is removed.
• Be sure that the replacement hard drive is the same interface and the same or larger capacity.
To remove the component:
1. Extend the hard drive drawer (on page 25).
there is another drive ready to install or the MDS600 is powered down.
page 58) and SAS and SATA hard drive LED combinations (on page 58).
For more information, see the HP Array Configuration Utility User Guide on the HP website
(http://www.hp.com
CAUTION: To avoid data loss, be sure that the drives are labeled and returned to the same
bays they were removed from.
).
Removal and replacement procedures 27
Page 28
2.
Remove the hard drive.
To replace the component:
1. Fully extend the hard drive lever.
2. Push the hard drive all the way into the drive bay, and then close the lever.
Hard drive drawer bezel
To remove the component:
1. Power down the MDS600 ("Power down" on page 25).
2. Extend the hard drive drawer (on page 25).
3. To access the screws securing the bezel to the hard drive drawer, remove the hard drives in device
bays 2 and 7.
For the location of these device bays, see "Device bay ID numbers (on page 57)."
CAUTION: To avoid data loss, be sure that the drives are labeled and returned to the same
bays they were removed from.
IMPORTANT: The screws are different lengths. Be sure to note the location of each screw
when removing them.
Removal and replacement procedures 28
Page 29
4.
Remove the eight T-8 Torx screws securing the bezel to the hard drive drawer.
5. Be sure the drawer handle is in the down position.
6. Lean the bezel forward, and then remove it from the hard drive drawer.
To replace the component, reverse the removal procedure. The screws are different lengths. Be sure they
are installed in the proper location.
Hard drive drawer display board
To remove the component:
1. Power down the MDS600 ("Power down" on page 25).
2. Disconnect the power cord from the AC source.
3. Extend the hard drive drawer (on page 25).
4. Remove the hard drives in device bays 2 and 7 ("Hard drive" on page 27).
Removal and replacement procedures 29
Page 30
For the location of these device bays, see "Device bay ID numbers (on page 57)."
5. Remove the hard drive drawer bezel ("Hard drive drawer bezel" on page 28).
6. Remove the T-15 Torx screw securing the display board assembly to the hard drive drawer, and then
lift the assembly straight up to remove it from the drawer.
7. Turn the display board assembly over, remove the two T-15 Torx screws securing the board to the
cover, and lift the board straight out.
Removal and replacement procedures 30
Page 31
8.
Disconnect the cable from the display board.
To replace the component, reverse the removal procedure.
Fan
IMPORTANT: Configurations using power cord part number 142263-004, located on the
power cord label, require that the power cord be removed before removing a fan.
Before removing a fan, do the following:
• Verify the status of the fan to be replaced by reviewing rear panel LEDs and buttons (on page 56).
• Be sure that your configuration can support your actions. If the proper redundancy is not in place,
power down the MDS600 before beginning this procedure.
To remove the component:
1. Be sure that the hard drive drawer is closed.
Removal and replacement procedures 31
Page 32
2.
Remove the fan.
CAUTION: For best cooling practices, do not operate the enclosure for extended periods with
more than one component or blank removed. When removing an active component
To replace the fan, install it into the fan bay and push until it locks into place.
permanently, replace it with a blank.
Hot-plug I/O module
Before removing the component, be sure to do the following:
• Verify the status of the I/O module to be replaced by reviewing rear panel LEDs and buttons (on
page 56).
• Be sure that your configuration can support your actions. If the proper redundancy is not in place,
power down the MDS600 before beginning this procedure.
To remove the component:
1. Be sure the hard drive drawer is closed all the way.
2. Disconnect the SAS cables.
Removal and replacement procedures 32
Page 33
3.
Release the I/O handle, push the I/O handle down until it ejects the I/O module, and then remove
the I/O module.
CAUTION: For best cooling practices, do not operate the enclosure for extended periods with
more than one component or blank removed. When removing an active component
permanently, replace it with a blank.
To replace the component, reverse the removal procedure. Be sure the I/O module is fully seated and the
I/O module handle is in the locked position.
Power supply
Before removing the component, be sure to do the following:
• Verify the status of the power supply to be replaced by reviewing rear panel LEDs and buttons (on
page 56).
• Be sure that your configuration can support your actions. If the proper redundancy is not in place,
power down the MDS600 before beginning this procedure.
To remove the component:
1. Disconnect the AC power cord.
Removal and replacement procedures 33
Page 34
2.
Remove the component as indicated.
To replace the component, reverse the removal procedure.
Hard drive drawer
To remove the component:
1. Power down the MDS600 ("Power down" on page 25).
2. Disconnect all cables.
3. Remove all power supplies ("Power supply" on page 33).
4. Remove all fan modules ("Fan" on page 31).
5. Remove all hard drives ("Hard drive" on page 27).
CAUTION: To avoid data loss, be sure that the drives are labeled and returned to the same
6. Be sure the hard drive drawer is closed completely.
7. Remove all I/O modules ("Hot-plug I/O module" on page 32).
8. Pull down the handle on the front of the drawer, but do not extend the drawer.
bays they were removed from.
Removal and replacement procedures 34
Page 35
9.
Push up and hold the two release mechanisms on the I/O bays, and then push the drawer forward
about 15 cm (6 in).
WARNING: TIP HAZARD! To reduce the risk of personal injury or damage to the equipment,
do not extend the hard drive drawers beyond the supporting surface when the unit is not
installed in a rack.
WARNING: To reduce the risk of personal injury or damage to the equipment, ensure that
only one hard drive drawer is extended at a time.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Never reach inside the chassis while the system is powered up.
10. Remove the power block ("Power block" on page 39).
• Perform service on system components only as instructed in the user documentation.
Removal and replacement procedures 35
Page 36
11.
Extend the hard drive drawer until it clicks.
12. Compress the cable management arm and push toward the drawer to lock it into place.
Removal and replacement procedures 36
Page 37
13.
Push in to release the four locking mechanisms on the rails located on the side and bottom of the
drawer.
14. Remove the hard drive drawer.
To replace the component:
1. Slide the rails back into the chassis.
2. Align the top right edge of the drawer with the flange at the top of the chassis and align the four
rails on the left side and bottom of the drawer bay.
CAUTION: To avoid damage to the equipment, HP recommends using two people to perform
this step.
Removal and replacement procedures 37
Page 38
3. Push the drawer in about 25 cm (10 in).
4. Release the cable management arm and expand to the rear of the chassis.
5. Push the drawer in another 25 cm (10 in).
6. Install the power block ("Power block" on page 39).
WARNING: Pinch hazard—Keep hands out of front and rear of chassis when closing hard
drive drawers.
7. Install the hard drives.
Be sure that the drives are returned to the drive bays they were removed from.
8. Close the drawer.
9. Install all rear panel components.
10. Connect the cables.
Removal and replacement procedures 38
Page 39
Power block
To remove the component:
1. Power down the MDS600 ("Power down" on page 25).
2. Disconnect all cables.
3. Remove all power supplies ("Power supply" on page 33).
4. Remove all fan modules ("Fan" on page 31).
5. Remove all I/O modules ("Hot-plug I/O module" on page 32).
6. Disengage the cable management arm lock from each hard drive drawer:
a. Pull the mechanism up and then toward the rear of the chassis to disengage it from the locking
plate.
b. Slide the cable management arm off the locking plate.
Removal and replacement procedures 39
Page 40
7.
Loosen the screw securing the power block to the chassis, press down on the release lever, and then
slowly remove the power block. The signal and power cables are still attached.
8. While supporting the power block, disconnect the signal and power cables on each side of the
power block.
To replace the component, reverse the removal procedure.
Fan board
To remove the component:
1. Power down the MDS600 ("Power down" on page 25).
2. Disconnect all cables.
3. Remove all power supplies ("Power supply" on page 33).
4. Remove all fan modules ("Fan" on page 31).
5. Remove the hard drives ("Hard drive" on page 27).
Removal and replacement procedures 40
Page 41
CAUTION: To avoid data loss, be sure that the drives are labeled and returned to the same
bays they were removed from.
6. Be sure that the hard drive drawer is closed.
7. Remove all I/O modules ("Hot-plug I/O module" on page 32).
8. Remove the power block ("Power block" on page 39).
9. Remove the hard drive drawer ("Hard drive drawer" on page 34).
10. Remove the four T-10 Torx screws securing the fan cage to the hard drive drawer, and then remove
the fan cage.
11. Remove the two T-15 Torx screws securing the fan board to the hard drive drawer, and then remove
the fan board, being careful not to disconnect the two cables.
Removal and replacement procedures 41
Page 42
12.
Disconnect the cables.
To replace the component, reverse the removal procedure.
Dual 7-segment display board
To remove the component:
1. Power down the MDS600 ("Power down" on page 25).
2. Disconnect all cables.
3. Remove all power supplies ("Power supply" on page 33).
4. Remove the fans ("Fan" on page 31).
5. Remove the I/O modules ("Hot-plug I/O module" on page 32).
6. Remove the power block ("Power block" on page 39).
Removal and replacement procedures 42
Page 43
7.
Disconnect the signal cables, remove the four T-15 Torx screws securing the dual 7-segment display
board to the power block, and then remove the 7-segment display board.
To replace the component, reverse the removal procedure.
Power button/UID board
To remove the component:
1. Power down the MDS600 ("Power down" on page 25).
2. Disconnect all cables.
3. Remove all power supplies ("Power supply" on page 33).
4. Remove the fans ("Fan" on page 31).
5. Remove the I/O modules ("Hot-plug I/O module" on page 32).
6. Remove the power block ("Power block" on page 39).
Removal and replacement procedures 43
Page 44
7.
Disconnect the signal cables, remove the four T-15 Torx screws securing the power button/UID
board to the power block, and then remove the power button/UID board.
To replace the component, reverse the removal procedure.
Cable management arm
To remove the component:
1. Power down the MDS600 ("Power down" on page 25).
2. Disconnect all cables.
3. Remove all power supplies ("Power supply" on page 33).
4. Remove the fans ("Fan" on page 31).
5. Remove all hard drives ("Hard drive" on page 27).
CAUTION: To avoid data loss, be sure that the drives are labeled and returned to the same
6. Be sure that the hard drive drawer is closed.
7. Remove the I/O modules ("Hot-plug I/O module" on page 32).
8. Remove the power block ("Power block" on page 39).
9. Remove the hard drive drawer ("Hard drive drawer" on page 34).
bays they were removed from.
Removal and replacement procedures 44
Page 45
10.
Located behind the cable management arm, remove the T-15 Torx screw that secures the cables to
the hard drive drawer, and then remove the cables.
11. Located behind the cable management arm, lift up on the tab to release the latch, and then slide the
cable management arm off to remove it.
12. Lay the drawer on its side with the hard drive bays facing down.
Removal and replacement procedures 45
Page 46
13.
Remove the 11 screws securing the backplane cover plate. The screws are different sizes. Use the
following illustration and table to identify and keep track of the screws.
Item Description
1 Flushmount T-10 Torx screws
2 T-15 Torx screws
3 5/8-in T-15 Torx screws
14. Remove the backplane board:
a. Remove the thumbscrews securing the backplane board to the drawer.
b. Disconnect the LED panel cable.
c. Lift the board up at the front of the drawer, and then rotate toward the bottom side of the drawer.
Removal and replacement procedures 46
Page 47
15.
Disconnect the cables.
When reconnecting the cables, use the following illustration and table to be sure the cables are properly
reconnected.
Item Description
1 Fan signal cable
2 Red 12V power cable
3 Black GND cable
4 Fan power cable
5 Power signal cable
1. Thread the cables through the opening in the drawer.
2. Remove the cable management arm.
To replace the cable management arm:
Removal and replacement procedures 47
Page 48
1.
Thread the cables through the opening in the drawer, and then connect them to the backplane
board.
CAUTION: To avoid damage to the equipment, be sure that the cables are properly
connected. The red cable is 12V. The black cable is GND.
2. Install the backplane board:
a. Be sure the board is lined up on the standoffs.
b. Install the screws.
3. Connect the LED panel cable.
4. Install the cover.
5. Install the cable management arm.
6. Install the hard drive drawer.
7. Install the hard drives.
8. Close the hard drive drawer.
9. Install all rear panel components.
10. Connect the cables.
Removal and replacement procedures 48
Page 49
Diagnostic tools
Integrated Management Log
The IML records hundreds of events and stores them in an easy-to-view form. The IML timestamps each
event with 1-minute granularity.
You can view recorded events in the IML in several ways, including the following:
• From within HP SIM
• From within Survey Utility
• From within operating system-specific IML viewers
o For NetWare: IML Viewer
o For Windows®: IML Viewer
o For Linux: IML Viewer Application
• From within the iLO2 user interface
• From within HP Insight Diagnostics
For more information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack.
Array Diagnostic Utility
The HP Array Diagnostics Utility is a web-based application that creates a report of all HP storage
controllers and disk drives. This report provides vital information to assist in identifying faults or conditions
that may require attention. ADU can be accessed from the SmartStart CD or downloaded from the HP
website (http://www.hp.com
).
Array Configuration Utility
ACU is a browser-based utility with the following features:
• Runs as a local application or remote service
• Supports online array capacity expansion, logical drive extension, assignment of online spares, and
RAID or stripe size migration
• Suggests the optimum configuration for an unconfigured system
• Provides different operating modes, enabling faster configuration or greater control over the
configuration options
• Remains available any time that the server is on
• Displays on-screen tips for individual steps of a configuration procedure
Diagnostic tools 49
Page 50
For optimum performance, the minimum display settings are 800 × 600 resolution and 256 colors.
Servers running Microsoft® operating systems require Internet Explorer 5.5 (with Service Pack 1) or later.
For Linux servers, refer to the README.TXT file for additional browser and support information.
For more information, refer to the Configuring Arrays on HP Smart Array Controllers Reference Guide on
the Documentation CD or the HP website (http://www.hp.com
).
Diagnostic tools 50
Page 51
Component identification
Front panel components
Item Description
1 Drawer 1
2
3 Drawer 2
4
Drawer 1 diagnostic cable access (For use by
authorized HP personnel only)
Drawer 2 diagnostic cable access (For use by
authorized HP personnel only)
Diagnostic cable access
IMPORTANT: Use of the diagnostic cable connectors is reserved for authorized HP personnel
only.
Component identification 51
Page 52
To access the connectors for diagnostic cables, use a small flat-head screwdriver to lift up and release the
access tab.
Component identification 52
Page 53
Front panel LEDs and button
Item Description Status
1 Hard drive LEDs
Normal mode
(UID LED is solid)
Green = The drive is online, but is not
currently active.
Flashing irregularly green = The drive
is active and it is operating normally.
Flashing green (1 Hz) = Do not
remove the drive. Removing the drive
may terminate the current operation
and cause data loss. The drive is
rebuilding, or it is part of an array
that is undergoing expansion, logical
drive extension, a stripe size
migration, or RAID migration.
Flashing amber/green = Drive is
configured and indicating a predictive
failure. The drive may also be
undergoing a rebuild, expansion,
extension, or migration.
Flashing amber (1 Hz) = A predictive
failure alert has been received for this
drive. Replace the drive as soon as
possible.
Amber = Drive failure, link failure, or
mismatched configuration.
Off = The drive is offline, a spare, or
not configured as part of an array.
Component identification 53
Page 54
Item Description Status
1 Hard drive LEDs
Drive locate mode
(UID LED is flashing)
2 UID button/LED
3 Internal Health LED Green = System health is good
4 GSI LED
Green = The drive has been selected
by a management application and it
is operating normally.
Flashing amber (1 Hz) = The drive is
not selected and is indicating a
predictive failure.
Flashing amber/green = The drive has
been selected by a management
application and is indicating a
predictive failure.
Amber = The drive might or might not
be selected and is indicating drive
failure, link failure, or mismatched
configuration.
Off = The drive is not selected.
Blue = UID LED is enabled from the
UID button
Blue flashing = Item 1 is in locate
mode
Off = UID LED is disabled
Off = System is off
Amber = Enclosure requires service
check: I/O, fan and power supply
LEDs, and AC power cables to power
supplies.
Off = Enclosure is functioning
normally.
Component identification 54
Page 55
Rear panel components
The figure shows a maximum configuration. Your enclosure might appear differently, for example,
containing power supply or I/O module blanks, depending on the configuration that was ordered.
Item Description
1 Power supply 1
2 Power On/UID 2 status panel
3 Fan module 1 (Drawer 2)
4 Primary I/O module (Drawer 2)
5 SAS port 1 connector
6 SAS port 2 connector
7 Power supply 3
8 UID 1 status panel
9 Fan module 1 (Drawer 1)
10 Primary I/O module (Drawer 1)
11 SAS port 1 connector
12 SAS port 2 connector
13 SAS port 1 connector
14 SAS port 2 connector
15 Secondary I/O module (Drawer 1)
16 Fan module 2 (Drawer 1)
17 Power supply 4
18 SAS port 1 connector
19 SAS port 2 connector
20 Secondary I/O module (Drawer 2)
21 Fan module 2 (Drawer 2)
Component identification 55
Page 56
Item Description
•
•
•
22 Power supply 2
Rear panel LEDs and buttons
Item Description Status
1
2 Internal Health LED Green = System health is good.
3 GSI LED
4
5 Power supply LED
Power On/Standby
button and system power
LED
UID button/LED (Drawer
2)
Green = On
Amber = Standby (auxiliary power
present)
Off = Off
Off = System is off.
Amber = Enclosure requires service
check: I/O, fan and power supply
LEDs, and AC power cables to power
supplies.
Off = Enclosure is functioning
normally.
Blue = UID LED is enabled from the
UID button.
Blue flashing = System is in hard drive
locate mode or an enclosure firmware
update is in progress.
Off = UID LED is disabled.
Green = Power on and power supply
functioning properly
Off = One or more of the following
conditions exists:
System powered off
AC power unavailable
Power supply failed
Component identification 56
Page 57
•
Item Description Status
Power supply exceeded current
limit
6 System fan LED Green = Normal operation
Amber flashing = Fault
Off = Fan unseated from connector or
failed
7 I/O module LED Green = System activity
Amber = Fault
Off = Enclosure is powered off.
8 7-segment display 1 = SES overall warning
2 = Temperature sensor warning
3 = System fan warning
4 = Power supply warning
5 = Host GSI enabled
6 = I/O Pic upgrade needed
7 = Power supply Pic upgrade needed
8 = CPLD upgrade needed
9 = Standby heartbeat failure
10 = Remote I/O module heartbeat
failure
9
UID button/LED (Drawer
1)
Blue = UID LED is enabled from the
UID button.
Blue flashing = System is in hard drive
locate mode or an enclosure firmware
update is in progress.
Off = UID LED is disabled.
Device bay ID numbers
Component identification 57
Page 58
SAS and SATA hard drive LEDs
Item Description
1 Fault/UID LED (amber/blue)
2 Online LED (green)
SAS and SATA hard drive LED combinations
Online/activity
LED (green)
On, off, or
flashing
On, off, or
flashing
On
On Off The drive is online, but it is not currently active.
Flashing regularly
(1 Hz)
Flashing regularly
(1 Hz)
Fault/UID LED
(amber/blue)
Alternating amber
and blue
Steadily blue
Amber, flashing
regularly (1 Hz)
Amber, flashing
regularly (1 Hz)
Off
Interpretation
The drive has failed, or a predictive failure alert has been
received for this drive; it also has been selected by a
management application.
The drive is operating normally, and it has been selected by a
management application.
A predictive failure alert has been received for this drive.
Replace the drive as soon as possible.
Do not remove the drive. Removing a drive may terminate the
current operation and cause data loss.
The drive is part of an array that is undergoing capacity
expansion or a stripe size migration, but a predictive failure
alert has been received for this drive. To minimize the risk of
data loss, do not replace the drive until the expansion or
migration is complete.
Do not remove the drive. Removing a drive may terminate the
current operation and cause data loss.
The drive is rebuilding, or it is part of an array that is
undergoing capacity expansion or a stripe size migration.
Component identification 58
Page 59
Online/activity
LED (green)
Flashing
irregularly
Flashing
Fault/UID LED
(amber/blue)
Amber, flashing
regularly (1 Hz)
Off The drive is active and it is operating normally.
irregularly
Off Steadily amber
Off
Amber, flashing
regularly (1 Hz)
Off Off
Interpretation
The drive is active, but a predictive failure alert has been
received for this drive. Replace the drive as soon as possible.
A critical fault condition has been identified for this drive and
the controller has placed it offline. Replace the drive as soon as
possible.
A predictive failure alert has been received for this drive.
Replace the drive as soon as possible.
The drive is offline, a spare, or not configured as part of an
array.
Component identification 59
Page 60
Specifications
Environmental specifications
Specification Value
Temperature range*
Operating 10°C to 35°C (50°F to 95°F)
Maximum rate of change is 10º C/hr (50º F/hr)
Storage -30°C to 60°C (-22°F to 140°F)
Maximum rate of change is 20º C/hr (68º F/hr)
Relative humidity**
Operating
Storage
Altitude ‡
Operating 3048 m (10,000 ft)
Non-operating 9144 m (30, 000 ft)
* Temperature ratings shown are for sea level. An altitude derating of 1°C per 300 m (1.8°F per 1,000 ft) to 3048
m (10,000 ft) is applicable. No direct sunlight allowed. The upper limit may be limited by the type and number of
options installed.
** Storage maximum humidity of 95% is based on a maximum temperature of 45°C (113°F). Altitude maximum for
storage corresponds to a pressure minimum of 70 KPa.
‡ Maximum allowable altitude change rate is 457 m/min (1500 ft/min).
10% to 90% relative humidity (Rh), 28º C (82.4º F)
maximum wet bulb temperature, non-condensing
5% to 95% relative humidity (Rh), 38.7º C (101.66º F)
maximum wet bulb temperature, non-condensing
This value may be limited by the type and number of
options installed.
Storage array specifications
Specification Value
Height 22.10 cm (8.70 in)
Depth 89.12 cm (35.08 in)
Width 44.70 cm (17.60 in)
Weight (maximum) 145.15 kg (320.00 lb)
Weight (no drives installed) 72.58 kg (160.00 lb)
Specifications 60
Page 61
Acronyms and abbreviations
ADU
Array Diagnostics Utility
CPLD
complex programmable logic device
GSI
global service indicator
I/O
input/output
IML
Integrated Management Log
PIC
peripheral interface controller
SAS
serial attached SCSI
SATA
serial ATA
SES
SCSI Enclosure Services
SIM
Systems Insight Manager
UID
unit identification
Acronyms and abbreviations 61
Page 62
Index
A
hard drive LEDs 58
hard drives 27
ACU (Array Configuration Utility) 49
ADU (Array Diagnostic Utility) 49
B
buttons 51
C
cable management arm 44
cautions 23
components 51
connectors 51, 55
customer self repair (CSR) 5
D
device numbers 57
diagnostic cable access 51
diagnostic tools 49
display board, hard drive drawer, removing 29
drive LEDs 58
dual 7-segment display board 42
I
I/O module 32
IML (Integrated Management Log) 49
L
LED, heartbeat 53, 56
LED, system fault 53, 56
LED, system power 56
LED, UID 53
LEDs 51, 56, 58
LEDs, fan 56
LEDs, front panel 53
LEDs, hard drive 58
LEDs, I/O module 56
LEDs, power supply 56
LEDs, rear panel 56
M
management tools 49
mechanical components 16
E
electrostatic discharge 23
environmental specifications 60
F
fan board 40
fans, removing 31
features 51
front panel components 51
front panel LEDs 53
H
hard drive blanks 26
hard drive drawer bezel, removing 28
hard drive drawer display board, removing 29
hard drive drawer, extending 25
hard drive drawer, removing 34
P
power block, removing 39
power button/UID board, removing 43
power supply 33
powering down 25
R
rear panel buttons 56
rear panel components 55
rear panel LEDs 56
required tools 23
S
safety considerations 23
SAS hard drive LEDs 58
SAS/SATA LED combinations 58
SATA hard drive LEDs 58
Index 62
Page 63
specifications 60
static electricity 23
system components 19, 51
U
utilities 49
W
warnings 23
Index 63
Loading...