HP Mini 2102 User Manual

Mini User Guide
© Copyright 2010 Hewlett-Packard Development Company, L.P.
Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Second Edition: May 2010
First Edition: January 2010
Document Part Number: 599181-002
Product notice
This user guide describes features that are common to most models. Some features may not be available on your computer.
To obtain the latest information in the Mini User Guide, go to the HP Web site at
http://www.hp.com/support.
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of Information Technology Equipment (IEC 60950).
iii
iv Safety warning notice
Table of contents
1 Getting started ................................................................................................................................................ 1
2 Knowing the parts ........................................................................................................................................... 2
Identifying the hardware ....................................................................................................................... 2
Top components .................................................................................................................. 2
TouchPad ............................................................................................................ 2
Lights ................................................................................................................... 3
Keys .................................................................................................................... 4
Front components ................................................................................................................ 4
Right-side components ........................................................................................................ 5
Left-side components .......................................................................................................... 6
Display components ............................................................................................................ 7
Bottom components ............................................................................................................. 8
Removing the vanity cover .................................................................................................. 8
Replacing the vanity cover ................................................................................................. 10
Wireless antennas ............................................................................................................. 11
Additional hardware components ...................................................................................... 12
Identifying the labels ........................................................................................................................... 12
3 Power management ...................................................................................................................................... 14
Setting power options ......................................................................................................................... 14
Using power-saving states ................................................................................................. 14
Initiating and exiting Sleep ................................................................................ 14
Initiating and exiting Hibernation ....................................................................... 14
Using the Power icon ......................................................................................................... 15
Using power management ................................................................................ 15
Viewing the current power management settings ............................. 15
Changing the current power management settings .......................... 15
Using external AC power .................................................................................................................... 15
Connecting the AC adapter ............................................................................................... 16
Using battery power ........................................................................................................................... 16
Displaying the remaining battery charge ........................................................................... 17
Inserting or removing the battery ....................................................................................... 17
Charging a battery ............................................................................................................. 18
v
Maximizing battery discharge time .................................................................................... 19
Managing low battery levels .............................................................................................. 19
Identifying low battery levels ............................................................................. 19
Resolving a low battery level ............................................................................. 20
Resolving a low battery level when external power is available ....... 20
Resolving a low battery level when a charged battery is available ... 20
Resolving a low battery level when no power source is available .... 20
Resolving a low battery level when the computer cannot exit
Hibernation ....................................................................................... 20
Calibrating a battery ........................................................................................................... 20
Step 1: Fully charge the battery ........................................................................ 20
Step 2: Disable Hibernation and Sleep ............................................................. 21
Step 3: Discharge the battery ............................................................................ 21
Step 4: Fully recharge the battery ..................................................................... 22
Step 5: Reenable Hibernation and Sleep .......................................................... 22
Conserving battery power .................................................................................................. 22
Storing a battery ................................................................................................................ 22
Disposing of a used battery ............................................................................................... 23
Shutting down the computer ............................................................................................................... 23
4 Internet ........................................................................................................................................................... 24
Connecting to a wired network ........................................................................................................... 25
Connecting to a wireless network ....................................................................................................... 26
Using wireless devices ...................................................................................................... 26
Identifying wireless and network icons .............................................................. 26
Using the wireless controls ............................................................................... 26
Using the wireless action key ............................................................................ 27
Using operating system controls ....................................................................... 27
Using a WLAN ................................................................................................................... 27
Setting up a WLAN ............................................................................................ 28
Protecting your WLAN ....................................................................................... 28
Connecting to a WLAN ...................................................................................... 29
Roaming to another network ............................................................................. 30
Using Bluetooth wireless devices ....................................................................................................... 31
Bluetooth ............................................................................................................................ 31
5 Multimedia ..................................................................................................................................................... 32
Multimedia features ............................................................................................................................ 32
Identifying your multimedia components ........................................................................... 32
Adjusting the volume ......................................................................................................... 34
Using the media activity action keys .................................................................................................. 35
Multimedia software ........................................................................................................................... 36
Using other preinstalled multimedia software .................................................................... 36
vi
Installing multimedia software from the Internet ................................................................ 36
Audio .................................................................................................................................................. 36
Connecting external audio devices .................................................................................... 36
Checking your audio functions ........................................................................................... 37
Video .................................................................................................................................................. 37
Connecting an external monitor or projector ...................................................................... 37
Webcam ............................................................................................................................................. 39
6 Security .......................................................................................................................................................... 40
Protecting the computer ..................................................................................................................... 40
Using passwords ................................................................................................................................ 40
Setting passwords in the operating system ....................................................................... 41
Setting passwords in Setup Utility ..................................................................................... 41
Administrator password ..................................................................................... 41
Managing an administrator password ............................................... 42
Entering an administrator password ................................................. 42
Power-on password .......................................................................................... 42
Managing a power-on password ...................................................... 42
Entering a power-on password ......................................................... 43
Using firewall software ....................................................................................................................... 44
Setting up automatic online updates .................................................................................................. 45
7 Digital cards .................................................................................................................................................. 46
Inserting a digital card ........................................................................................................................ 46
Removing a digital card ...................................................................................................................... 47
8 USB devices .................................................................................................................................................. 48
Using a USB device ........................................................................................................................... 48
Connecting a USB device .................................................................................................. 48
Removing a USB device .................................................................................................... 48
9 Pointing devices and keyboard ................................................................................................................... 50
Using pointing devices ....................................................................................................................... 50
Using the TouchPad .......................................................................................................... 50
Connecting an external mouse .......................................................................................... 50
Using the keyboard ............................................................................................................................ 50
Using the action keys ......................................................................................................... 50
Using hotkeys .................................................................................................................... 51
10 Drives ........................................................................................................................................................... 53
Identifying installed drives .................................................................................................................. 53
Handling drives ................................................................................................................................... 53
vii
Using external drives .......................................................................................................................... 54
Using optional external devices ......................................................................................... 55
11 Memory modules ........................................................................................................................................ 56
12 Setup Utility ................................................................................................................................................. 59
Starting Setup Utility ........................................................................................................................... 59
Using Setup Utility .............................................................................................................................. 59
Changing the language of Setup Utility ............................................................................. 59
Navigating and selecting in Setup Utility ............................................................................ 59
Displaying system information ........................................................................................... 60
Restoring default settings in Setup Utility .......................................................................... 60
Exiting Setup Utility ............................................................................................................ 60
Setup Utility menus ............................................................................................................................ 61
Main menu ......................................................................................................................... 61
Security menu .................................................................................................................... 61
System Configuration menu .............................................................................................. 61
Diagnostics menu .............................................................................................................. 62
Index ................................................................................................................................................................... 63
viii

1 Getting started

Your HP computer's main operating system is SuSE Linux Enterprise Desktop. The operating system displays the desktop on the display and controls your HP computer's hardware, peripherals, and software programs.
1

2 Knowing the parts

Identifying the hardware

Components included with the computer may vary by region and model. The illustrations in this chapter identify the standard features on most computer models.
To see a list of hardware installed in the computer:
Select Computer > Control Center > YaST > System > Hardware Information.

Top components

TouchPad
Component Description
(1)
(2) TouchPad Moves the pointer and selects or activates items on
(3) Left TouchPad button Functions like the left button on an external mouse.
(4) Right TouchPad button Functions like the right button on an external mouse.
2 Chapter 2 Knowing the parts
TouchPad on/off button Turns the TouchPad on and off. Quickly double-tap
the button to turn the TouchPad on and off.
the screen.
Lights
Component Description
(1) TouchPad light
(2) Caps lock light On: Caps lock is on.
(3)
(4)
Mute light On: Speaker sound is off.
Wireless light
On: The TouchPad is disabled.
Off: The TouchPad is enabled.
White: An integrated wireless device, such as
a wireless local area network (WLAN) device and/or a Bluetooth® device, is on.
NOTE: Wireless devices are enabled at the
factory.
Off: All wireless devices are off.
Identifying the hardware 3
Keys
Component Description
(1) Action keys Execute frequently used system functions.
(2) fn key Executes frequently used system functions when
pressed in combination with an action key or the
esc key.

Front components

Component Description
(1) Speakers (2) Produce sound.
NOTE: The fn+esc key combination displays
system information, including the product name and serial number, saving you from removing the battery to see the serial number information.
4 Chapter 2 Knowing the parts

Right-side components

Component Description
(1) Media Card Reader Supports the following optional digital card formats:
Memory Stick (MS)
MS/Pro
MultiMediaCard (MMC)
Secure Digital High Capacity (SDHC) Memory
card (standard and large size)
xD-Picture card
(2)
(3) Power switch When the computer is off, slide the switch to turn
(4) Vent Enables airflow to cool internal components.
Power light
White: The computer is on.
Blinking white: The computer is in the Sleep
state.
Off: The computer is off or in Hibernation.
on the computer.
When the computer is on, briefly slide the switch
to initiate Hibernation.
When the computer is in the Sleep state, briefly
slide the switch to exit Sleep.
When the computer is in Hibernation, briefly slide
the switch to exit Hibernation.
If the computer has stopped responding and operating system shutdown procedures are ineffective, slide and hold the power switch for at least 5 seconds to turn off the computer.
To learn more about your power settings, select
Computer > Control Center > System > Power Management.
NOTE: The computer fan starts up automatically to
cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
(5)
USB ports (2) Connect optional USB devices.
Identifying the hardware 5
Component Description
(6)
(7)
RJ-45 (network) jack and cover Connects a network cable.
Security cable slot Attaches an optional security cable to the computer.

Left-side components

Component Description
(1) Power connector Connects an AC adapter.
(2) Battery light
NOTE: The security cable is designed to act as a
deterrent, but it may not prevent the computer from being mishandled or stolen.
Off: The computer is running on battery power.
Blinking white: The battery has reached a low
battery level, a critical battery level, or there is a battery error. When the battery reaches a critical battery level, the battery light begins blinking rapidly.
Amber: A battery is charging.
White: The computer is connected to external
power and the battery is fully charged.
(3)
(4) Vent Enables airflow to cool internal components.
(5)
External monitor port Connects an optional external display, such as a
Drive light On: The hard drive is being accessed.
monitor or projector, to the computer.
NOTE: The computer fan starts up automatically to
cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Off: The hard drive is idle.
6 Chapter 2 Knowing the parts
Component Description
(6)
(7)
USB port Connects an optional USB device.
Audio-out (headphone) jack/Audio-in (microphone) jack

Display components

Produces sound when connected to optional powered stereo speakers, headphones, earbuds, a headset, or television audio. Also connects an optional headset microphone.
NOTE: When an audio component is connected to
the jack, the computer speakers are disabled.
The audio component cable must have a 4­conductor connector.
Component Description
(1) Internal display switch Initiates Sleep if the display is closed while the power is
(2) Webcam light On: The webcam is in use.
on.
NOTE: The display switch is not visible from the outside
of the computer.
Identifying the hardware 7
Component Description
(3) Webcam Records video and captures still photographs.
NOTE: To record videos, you need to install additional
webcam software.
(4)
Internal microphone Records sound.

Bottom components

Component Description
(1) Battery release latches (2) Release the battery from the battery bay.
(2) Battery bay Holds the battery.

Removing the vanity cover

Removing the vanity cover allows access to the memory module compartment, SIM card insertion slot, regulatory label, and other important components. To remove the vanity cover:
1. Disconnect the computer from AC power.
2. Remove the battery.
NOTE: For more information, refer to the section “Inserting or removing the battery,” later in
this guide.
3. Press the right release button (1).
8 Chapter 2 Knowing the parts
4. Release the right side of the vanity cover (2) by lifting it slightly away from the base.
NOTE: It is normal for the vanity cover to flex slightly, and you may also hear some popping
noises when the vanity cover tabs disengage from the base.
5. Press the left release button (1).
6. Release the left side of the vanity cover (2) by lifting it slightly away from the base.
Identifying the hardware 9
7. Lift the bottom edge of the vanity cover (1) at an angle, and then lift the vanity cover away from
the base (2).

Replacing the vanity cover

Replace the vanity cover after accessing the memory module compartment, SIM card insertion slot, regulatory label, and other important components. To replace the vanity cover:
1. Place the vanity cover (1) above the computer at an angle, with the front edge toward the front of
the computer.
2. Seat the back edge of the vanity cover in the back edge of the computer by aligning the six tabs
on the vanity cover over the slots in the base, and then inserting the six tabs into the slots (2).
10 Chapter 2 Knowing the parts
3. Rotate the front edge (1) of the vanity cover down, and then firmly press the vanity cover onto
the base of the computer until it snaps into place (2).
4. Replace the battery.
NOTE: For more information, refer to the section “Inserting or removing the battery,” later in
this guide.

Wireless antennas

Component Description
(1) WWAN antennas (2) (select models only)* Send and receive wireless signals to communicate with wireless
wide-area networks (WWANs).
(2) WLAN antennas (2) (select models only)* Send and receive wireless signals to communicate with wireless
local-area networks (WLANs).
*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennas free from obstructions.
Identifying the hardware 11
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or region.

Additional hardware components

Component Description
(1) Power cord* Connects an AC adapter to an AC outlet.
(2) AC adapter Converts AC power to DC power.
(3) Battery* Powers the computer when the computer is not plugged into
*Batteries and power cords vary in appearance by region and country.

Identifying the labels

The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer.
Serial number label—Provides important information that you may need when contacting
technical support. The serial number label is affixed inside the battery bay.
external power.
Component
(1) Product name
(2) Serial number
12 Chapter 2 Knowing the parts
Component
(3) Product number
(4) Warranty period
(5) Model description (select models)
Regulatory label—Provides regulatory information about the computer, including the following:
Information about optional wireless devices and the approval markings of some of the
countries or regions in which the devices have been approved for use. An optional device may be a wireless local area network (WLAN) device. You may need this information when traveling internationally.
The serial number of your HP Mobile Broadband Module (select models only).
The regulatory label is located under the vanity cover of the computer. To access the regulatory label in the computer, refer to the section “Removing the vanity cover,” earlier in this guide.
Identifying the labels 13

3 Power management

Setting power options

Using power-saving states

The computer has two power-saving states enabled at the factory: Sleep and Hibernation.
When Sleep is initiated, the power light blinks and the screen clears. Your work is saved to memory. Exiting Sleep is faster than exiting Hibernation. If the computer is in the Sleep state for an extended period or if the battery reaches a critical battery level while in the Sleep state, the computer initiates Hibernation.
When Hibernation is initiated, your work is saved to a hibernation file on the hard drive and the computer turns off.
CAUTION: To prevent possible audio and video degradation, loss of audio or video playback
functionality, or loss of information, do not initiate Sleep or Hibernation while reading from or writing to a disc or an external media card.
NOTE: You cannot initiate any type of networking connection or perform any computer functions
while the computer is in the Sleep state or in Hibernation.
Initiating and exiting Sleep
The system is set at the factory to initiate Sleep after 15 minutes of inactivity when running on battery power and 25 minutes of inactivity when running on external power.
Power settings and timeouts can be changed using Power Management in Control Center.
With the computer on, you can initiate Sleep by clicking Computer > Shutdown > Suspend.
To exit Sleep:
Briefly slide the power switch.
When the computer exits Sleep, the power light turns on and your work returns to the screen where you stopped working.
Initiating and exiting Hibernation
The system is set at the factory to initiate Hibernation when the battery reaches a critical battery level.
NOTE: The system will not initiate Hibernation when running on external power.
NOTE: To reduce the risk of information loss, periodically save your work.
14 Chapter 3 Power management
Power settings and timeouts can be changed using Power Management in Control Center.
To initiate Hibernation:
Click Computer > Shutdown > Hibernate.
To exit Hibernation:
Briefly slide the power switch.
When the computer exits Hibernation, the power light turns on and your work returns to the screen where you stopped working.

Using the Power icon

The Power icon is located in the notification area, at the far right of the taskbar. The Power icon allows you to quickly access power settings, view remaining battery charge, and select a different power plan.
To display the percentage of remaining battery charge, hover over the Power icon.
To access Power Management Preferences, right-click the Power icon, and then click
Preferences.
Using power management
Power management is a collection of system settings that manages how the computer uses power. Power management can help you conserve power or maximize performance.
You can customize power management settings.
Viewing the current power management settings
Right-click the Power icon in the notification area, at the far right of the taskbar, and then click
Preferences.
Changing the current power management settings
1. Right-click the Power icon in the notification area, and then click Preferences.
2. Change the On AC Power, On Battery Power, and General settings, as needed.

Using external AC power

External AC power is supplied through an approved AC adapter.
WARNING! To reduce potential safety issues, use only the AC adapter provided with the computer,
a replacement AC adapter provided by HP, or a compatible AC adapter purchased from HP.
Connect the computer to external AC power under any of the following conditions:
WARNING! Do not charge the battery while you are onboard aircraft.
When you are charging or calibrating a battery
When you are installing or modifying system software
When you are writing information to a CD or DVD
Using external AC power 15
When you connect the computer to external AC power, the following events occur:
The battery begins to charge.
If the computer is turned on, the Power icon in the notification area changes appearance.
When you disconnect external AC power, the following events occur:
The computer switches to battery power.
The display brightness is automatically decreased to save battery life. To increase display
brightness, press the f3 action key or reconnect the AC adapter.

Connecting the AC adapter

WARNING! To reduce the risk of electric shock or damage to the equipment:
Plug the power cord into an AC outlet that is easily accessible at all times.
Disconnect power from the computer by unplugging the power cord from the AC outlet (not by unplugging the power cord from the computer).
If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3­pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The grounding pin is an important safety feature.
To connect the computer to external AC power, follow these steps:
1. Plug the AC adapter into the power connector (1) on the computer.
2. Plug the power cord into the AC adapter (2).
3. Plug the other end of the power cord into an AC outlet (3).

Using battery power

When a charged battery is in the computer and the computer is not plugged into external power, the computer runs on battery power. When the computer is plugged into external AC power, the computer runs on AC power.
16 Chapter 3 Power management
If the computer contains a charged battery and is running on external AC power supplied through the AC adapter, the computer switches to battery power if the AC adapter is disconnected from the computer.
NOTE: The display brightness is decreased to save battery life when you disconnect AC power. To
increase display brightness, use the f3 action key or reconnect the AC adapter.
You can keep a battery in the computer or in storage, depending on how you work. Keeping the battery in the computer whenever the computer is plugged into AC power charges the battery and also protects your work in case of a power outage. However, a battery in the computer slowly discharges when the computer is off and unplugged from external power.
WARNING! To reduce potential safety issues, use only the battery provided with the computer, a
replacement battery provided by HP, or a compatible battery purchased from HP.
Battery life varies, depending on power management settings, programs running on the computer, display brightness, external devices connected to the computer, and other factors.

Displaying the remaining battery charge

Move the pointer over the Power icon in the notification area, at the far right of the taskbar.
The time shown indicates the approximate running time remaining on the battery if the battery continues to provide power at the current level. For example, the time remaining will decrease when a
CD is playing and will increase when a CD stops playing.

Inserting or removing the battery

CAUTION: Removing a battery that is the sole power source may cause loss of information. To
prevent loss of information, save your work and initiate Hibernation or shut down the computer through the operating system before removing the battery.
To insert the battery:
1. Turn the computer upside down on a flat surface.
2. Align the tabs on the battery with the notches on the computer (1), and then insert the battery
into the battery bay (2). The battery release latches automatically lock the battery into place.
Using battery power 17
To remove the battery:
1. Turn the computer upside down on a flat surface.
2. Slide the battery release latches (1) to release the battery, lift the battery (2), and then remove
the battery.

Charging a battery

WARNING! Do not charge the computer battery while you are onboard aircraft.
The battery charges whenever the computer is plugged into external power through an AC adapter or an optional power adapter.
The battery charges whether the computer is off or in use, but it charges faster when the computer is off.
Charging may take longer if a battery is new, has been unused for 2 weeks or more, or is much warmer or cooler than room temperature.
To prolong battery life and optimize the accuracy of battery charge displays, follow these recommendations:
If you are charging a new battery, charge it fully before turning on the computer.
Charge the battery until the battery light turns white.
NOTE: If the computer is on while the battery is charging, the Power icon in the notification
area may show 100 percent charge before the battery is fully charged.
Allow the battery to discharge below 5 percent of a full charge through normal use before
charging it.
If the battery has been unused for one month or more, calibrate the battery instead of simply
charging it.
18 Chapter 3 Power management
The battery light displays charge status:
Off: The computer is running on battery power.
Blinking white: The battery has reached a low battery level, a critical battery level, or there is a
battery error.
Amber: A battery is charging.
White: The computer is connected to external power and the battery is fully charged.

Maximizing battery discharge time

Battery discharge time varies depending on the features you use while on battery power. Maximum discharge time gradually shortens, as the battery storage capacity naturally degrades.
Tips for maximizing battery discharge time:
Decrease the brightness on the display.
Remove the battery from the computer when it is not being used or charged.
Store the battery in a cool, dry location.
To change the settings in Power Management, refer to the “Changing the settings in Power Management” section in this chapter.

Managing low battery levels

The information in this section describes the alerts and system responses set at the factory. Some low-battery alerts and system responses can be changed using Power Management in Control Center. Preferences set using Power Management do not affect lights.
Identifying low battery levels
The computer takes the following actions for a critical battery level:
If Hibernation is enabled and the computer is on or in the Sleep state, the computer initiates
Hibernation.
If Hibernation is disabled and the computer is on or in the Sleep state, the computer remains
briefly in the Sleep state, and then shuts down and loses any unsaved information.
Using battery power 19
Resolving a low battery level
CAUTION: To reduce the risk of losing information when the computer reaches a critical battery
level and has initiated Hibernation, do not restore power until the power light turns off.
Resolving a low battery level when external power is available
Connect to an approved AC adapter.
Resolving a low battery level when a charged battery is available
1. Turn off the computer or initiate Hibernation.
2. Remove the discharged battery, and then insert a charged battery.
3. Turn on the computer.
Resolving a low battery level when no power source is available
Initiate Hibernation.
– or –
Save your work and shut down the computer.
Resolving a low battery level when the computer cannot exit Hibernation
When the computer lacks sufficient power to exit Hibernation, follow these steps:
1. Insert a charged battery or plug the computer into external power.
2. Exit Hibernation by briefly sliding the power switch.

Calibrating a battery

Calibrate a battery under the following conditions:
When battery charge displays seem inaccurate
When you observe a significant change in battery run time
Even if a battery is heavily used, it should not need to be calibrated more than once a month. It is also not necessary to calibrate a new battery.
Step 1: Fully charge the battery
WARNING! Do not charge the computer battery while you are onboard aircraft.
NOTE: The battery charges whether the computer is off or in use, but it charges faster when the
computer is off.
20 Chapter 3 Power management
To fully charge the battery:
1. Insert the battery into the computer.
2. Connect the computer to an AC adapter and then plug the adapter into external power.
The battery light on the computer turns amber.
3. Leave the computer plugged into external power until the battery is fully charged.
The battery light on the computer turns white.
Step 2: Disable Hibernation and Sleep
1. Click the Power icon in the notification area, and then click Preferences.
2. Under the Running on AC and Running on Battery tabs, record the current values for the
following settings:
Put the display to sleep when the computer is inactive for
Put the computer to sleep when it is inactive for
3. Change all 4 settings to Never.
4. Click Close.
Step 3: Discharge the battery
The computer must remain on while the battery is being discharged. The battery can discharge whether or not you are using the computer, but the battery will discharge faster while you are using it.
If you plan to leave the computer unattended during the discharge, save your information before
beginning the discharge procedure.
If you use the computer occasionally during the discharge procedure and have set energy-
saving timeouts, expect the following performance from the system during the discharge process:
The monitor will not turn off automatically.
Hard drive speed will not decrease automatically when the computer is idle.
System-initiated Hibernation will not occur.
To discharge a battery:
1. Unplug the computer from its external power source, but do not turn off the computer.
2. Run the computer on battery power until the battery is discharged. The battery light begins to
blink white when the battery has discharged to a low battery level. When the battery is discharged, the battery light turns off and the computer shuts down.
Using battery power 21
Step 4: Fully recharge the battery
To recharge the battery:
1. Plug the computer into external power and maintain external power until the battery is fully
recharged. When the battery is recharged, the battery light on the computer turns white.
You can use the computer while the battery is recharging, but the battery will charge faster if the computer is off.
2. If the computer is off, turn it on when the battery is fully charged and the battery light has turned
white.
Step 5: Reenable Hibernation and Sleep
CAUTION: Failure to reenable Hibernation after calibration may result in a full battery discharge and
information loss if the computer reaches a critical battery level.
1. Click the Power icon in the notification area, and then click Preferences.
2. Under the Running on AC and Running on Battery tabs, reset the previously recorded values
for the following settings:
Put the display to sleep when the computer is inactive for
Put the computer to sleep when it is inactive for
3. Click Close.

Conserving battery power

Select Powersave in Power Management under System Settings.
Turn off wireless and local area network (LAN) connections and exit modem applications when
you are not using them.
Disconnect external devices that are not plugged into an external power source, when you are
not using them.
Stop, disable, or remove any external media cards that you are not using.
Use the f2 and f3 action keys to adjust screen brightness as needed.
If you leave your work, initiate Sleep or Hibernation, or shut down the computer.

Storing a battery

CAUTION: To prevent damage to a battery, do not expose it to high temperatures for extended
periods of time.
If a computer will be unused and unplugged from external power for more than 2 weeks, remove the battery and store it separately.
To prolong the charge of a stored battery, place it in a cool, dry place.
NOTE: A stored battery should be checked every 6 months. If the capacity is less than 50 percent,
recharge the battery before returning it to storage.
Calibrate a battery before using it if it has been stored for one month or more.
22 Chapter 3 Power management

Disposing of a used battery

WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short
external contacts; do not dispose of in fire or water.
Refer to the Regulatory, Safety and Environmental Notices for battery disposal information.

Shutting down the computer

CAUTION: Unsaved information will be lost when the computer is shut down.
The Shutdown command closes all open programs, including the operating system, and then turns off the display and computer.
Shut down the computer under any of the following conditions:
When you need to replace the battery or access components inside the computer
When you are connecting an external hardware device that does not connect to a USB port
When the computer will be unused and disconnected from external power for an extended
period
To shut down the computer, follow these steps:
NOTE: If the computer is in the Sleep state or in Hibernation, you must first exit Sleep or
Hibernation before shutdown is possible.
1. Save your work and close all open programs.
2. Click Computer > Shutdown > Shutdown.
If the computer is unresponsive and you are unable to use the preceding shutdown procedures, try the following emergency procedures in the sequence provided:
Slide and hold the power switch for at least 5 seconds.
Disconnect the computer from external power and remove the battery.
Shutting down the computer 23

4 Internet

Your computer supports the following types of Internet access:
Wired—You can access the Internet by connecting to a broadband network using the RJ-45
(network) jack.
Wireless—For mobile Internet access, you can use a wireless connection. To learn about setting
up a wireless network or adding your computer to an existing network, refer to the “Connecting to a wireless network” section.
24 Chapter 4 Internet

Connecting to a wired network

Connecting to a local area network (LAN) requires an 8-pin, RJ-45 network cable (purchased separately). If the network cable contains noise suppression circuitry (1), which prevents interference from TV and radio reception, orient the circuitry end of the cable (2) toward the computer.
To connect the network cable:
WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a
modem cable or telephone cable into an RJ-45 (network) jack.
1. Plug the network cable into the network jack (1) on the computer.
2. Plug the other end of the cable into a network wall jack (2).
Connecting to a wired network 25

Connecting to a wireless network

Using wireless devices

Wireless technology transfers data across radio waves instead of wires. Your computer may be equipped with one or more of the following wireless devices:
Wireless local area network (WLAN) device—Connects the computer to wireless local area
networks (commonly referred to as Wi-Fi networks, wireless LANs, or WLANs) in corporate offices, your home, and public places such as airports, restaurants, coffee shops, hotels, and universities. In a WLAN, each mobile wireless device communicates with a wireless router or a wireless access point.
HP Mobile Broadband Module (select models only)—A wireless wide area network (WWAN)
device that provides access to information wherever mobile network operator service is available. In a WWAN, each mobile device communicates to a mobile network operator’s base station. Mobile network operators install networks of base stations (similar to cell phone towers) throughout large geographic areas, effectively providing coverage across entire states, regions, or even countries.
Bluetooth® device—Creates a personal area network (PAN) to connect to other Bluetooth-
enabled devices such as computers, phones, printers, headsets, speakers, and cameras. In a PAN, each device communicates directly with other devices, and devices must be relatively close together— typically within 10 meters (approximately 33 feet) of each other.
The computer supports the following IEEE industry standards:
802.11b, the first popular standard, supports data rates of up to 11 Mbps and operates at a
frequency of 2.4 GHz.
802.11g supports data rates of up to 54 Mbps and operates at a frequency of 2.4 GHz. An
802.11g WLAN device is backward compatible with 802.11b devices, so they can operate on the same network.
Identifying wireless and network icons
Icon Name Description
Wireless (connected) Indicates that the wireless network is connected and active.
Network status (connected) Indicates that the wired network is connected and active. If
Network status (disconnected) Indicates that either the wired or the wireless network is
Using the wireless controls
You can control the wireless devices in your computer using these features:
both wired and wireless connections are active, the operating system uses the wired connection because it is faster.
disconnected.
Operating system controls—This is the recommended method.
The f12 wireless action key
26 Chapter 4 Internet
Using the wireless action key
The computer has a wireless action key (f12), one or more wireless devices, and one wireless light. All of the wireless devices on your computer are enabled at the factory.
The wireless light indicates the overall power state of your wireless devices, not the status of individual devices. If the wireless light is white, at least one wireless device is on. If the wireless light is off, all wireless devices are off.
Because the wireless devices are enabled at the factory, you can use the wireless action key (f12) to turn on or turn off all of the wireless devices simultaneously. Individual wireless devices can be controlled through the Control Center or the Setup Utility.
NOTE: If the wireless devices are disabled, the wireless action key will not work until you reenable
your devices. Check the Setup Utility to be sure that the appropriate device is enabled, and then check Network Manager by right-clicking the Network icon in the notification area, at the far right of the taskbar.
If WLAN and Bluetooth are integrated on one card (select models only), the wireless action key enables or disables both devices.
Using operating system controls
To enable or disable a wireless and/or wired network device, right click the Network Connection icon in the notification area, at the far right of the taskbar. To enable one of the following devices, select the check box from the menu option. To disable the device, clear the check box.
Enable Networking (wired networking device)
Enable Wireless

Using a WLAN

With a WLAN device, you can access a wireless local area network (WLAN), which is composed of other devices and accessories that are linked by a wireless router or a wireless access point.
NOTE: The terms wireless router and wireless access point are often used interchangeably.
A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points
that can accommodate a large number of devices and accessories and can separate critical network functions.
A home or small office WLAN typically uses a wireless router, which allows several wireless and
wired devices to share an Internet connection, a printer, and files without requiring additional pieces of hardware or software.
To use the WLAN device in your computer, you must connect to a WLAN infrastructure (provided through a service provider or a public or corporate network).
Connecting to a wireless network 27
Setting up a WLAN
To set up a WLAN and connect to the Internet, you need the following equipment:
A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from
an Internet service provider (ISP)
A wireless router (purchased separately) (2)
computer equipped with a wireless device (3)
The illustration below shows an example of a wireless network installation that is connected to the Internet.
As your network grows, additional wireless and wired devices can be connected to the network to access the Internet.
For help in setting up your WLAN, refer to the information provided by your router manufacturer or your ISP.
Protecting your WLAN
It is essential to understand that because the WLAN standard was designed with only limited security capabilities—basically to foil casual eavesdropping rather than more powerful forms of attack— WLANs are vulnerable to well-known and well-documented security weaknesses.
WLANs in public areas, or “hotspots,” like coffee shops and airports may not provide any security. New technologies are being developed by wireless manufacturers and hotspot service providers that make the public environment more secure and anonymous. If you are concerned about the security of your computer in a hotspot, limit your network activities to noncritical e-mail and basic Internet surfing.
When you set up a WLAN or access an existing WLAN, always enable security features to protect your network from unauthorized access. The common security levels are Wi-Fi Protected Access (WPA)-Personal and Wired Equivalent Privacy (WEP). Because wireless radio signals travel outside the network, other WLAN devices can pick up unprotected signals and either connect to your network (uninvited) or capture information being sent across it. However, you can take precautions to protect your WLAN:
Use a wireless transmitter with built-in security
Many wireless base stations, gateways, or routers provide built-in security features such as wireless security protocols and firewalls. With the correct wireless transmitter, you can protect your network from the most common wireless security risks.
Work behind a firewall
A firewall is a barrier that checks both data and requests for data that are sent to your network, and discards any suspicious items. Firewalls are available in many varieties, both software and hardware. Some networks use a combination of both types.
Use wireless encryption
28 Chapter 4 Internet
A variety of sophisticated encryption protocols is available for your WLAN. Find the solution that works best for your network security:
Wired Equivalent Privacy (WEP) is a wireless security protocol that encodes or encrypts
all network data before it is transmitted using a WEP key. Usually, you can allow the network to assign the WEP key. Alternatively, you can set up your own key, generate a different key, or choose other advanced options. Without the correct key, others will not be able to use the WLAN.
WPA (Wi-Fi Protected Access), like WEP, uses security settings to encrypt and decrypt
data that is transmitted over the network. However, instead of using one static security key for encryptions as WEP does, WPA uses “temporal key integrity protocol” (TKIP) to dynamically generate a new key for every packet. It also generates different sets of keys for each device on the network.
Connecting to a WLAN
To connect to the WLAN, follow these steps:
1. Be sure that the WLAN device is on. If it is on, the wireless light is white. If the wireless light is
off, press the f12 action key to turn on the wireless connection.
2. Click the network icon in the notification area, at the far right of the taskbar.
3. Select your WLAN from the list, and then type the network security key, if required.
If the network is a security-enabled WLAN, you are prompted to enter a network security
key, which is a security code. Type the code, and then click Connect to complete the connection.
If the network is unsecured, meaning that anyone can access the network, the system
connects.
NOTE: If no WLANs are listed, you are out of range of a wireless router or access point.
NOTE: If you do not see the network you want to connect to, click Show all connections. A
list of options is displayed that includes creating a new network connection, as well as troubleshooting connection issues.
After the connection is made, place the mouse pointer over the network icon in the notification area, at the far right of the taskbar, to verify the name and status of the connection.
NOTE: The functional range (how far your wireless signals travel) depends on WLAN
implementation, router manufacturer, and interference from other electronic devices or structural barriers such as walls and floors.
More information about using a WLAN is available from your ISP and the manufacturer's instructions included with your wireless router and other WLAN equipment.
For a list of public WLANs near you, contact your ISP or search the Web. Web sites that list public WLANs include Cisco Internet Mobile Office Wireless Locations, Hotspotlist, and Geektools. Check with each public WLAN location for cost and connection requirements.
For additional information on connecting your computer to a corporate WLAN, contact your network administrator or IT department.
Connecting to a wireless network 29
Roaming to another network
When you move your computer within range of another WLAN, the operating system attempts to connect to that network. If the attempt is successful, your computer is automatically connected to the new network. If the operating system does not recognize the new network, follow the same procedure you used initially to connect to your WLAN.
30 Chapter 4 Internet

Using Bluetooth wireless devices

A Bluetooth device provides short-range wireless communications that replace the physical cable connections that traditionally link electronic devices such as the following:
Computers (desktop, notebook, PDA)
Phones (cellular, smart phone)
Imaging devices (printer, camera)
Audio devices (headset, speakers)
Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network (PAN) of Bluetooth devices. For information on configuring and using Bluetooth devices, refer to the Bluetooth software Help.

Bluetooth

The strength of Bluetooth is in synchronizing information transfers between your Mini and wireless devices including cellular phones, printers, cameras, and PDAs. The inability to consistently connect two or more computers to share the Internet through Bluetooth is a limitation of Bluetooth and the operating system.
Using Bluetooth wireless devices 31

5 Multimedia

Multimedia features

Your computer includes multimedia features that allow you to listen to music, watch movies, and view pictures. Your computer may include the following multimedia components:
Integrated speakers for listening to music
Integrated webcam that allows you to capture photographs and videos
Preinstalled multimedia software that allows you to play and manage your music, movies, and
pictures
NOTE: Your computer may not include all of the components listed.
The following sections explain how to identify and use the multimedia components included with your computer.

Identifying your multimedia components

The following illustration and table describe the multimedia features of the computer.
32 Chapter 5 Multimedia
Component Description
(1) Webcam light On: The webcam is in use.
(2) Webcam Records video and captures still photographs.
NOTE: To record videos, you need to install additional
webcam software.
(3) Internal microphone Records sound.
(4) Speakers (2) Produce sound.
(5)
(6)
volume mute action key (f11) Mute speaker sound.
volume up action key (f10) Increases speaker sound.
Multimedia features 33
Component Description
(7)
(8)
volume down action key (f9) Decreases speaker sound.
Audio-out (headphone) jack/Audio-in (microphone) jack

Adjusting the volume

You can adjust the volume using the following computer volume action keys:
To decrease volume, press the volume down action key (f9) (1)
To increase volume, press the volume up action key (f10) (2)
To mute or restore volume, press the volume mute action key (f11) (3)
Produces sound when connected to optional powered stereo speakers, headphones, earbuds, a headset, or television audio. Also connects an optional headset microphone.
WARNING! To reduce the risk of personal injury, adjust
the volume before putting on headphones, earbuds, or a headset. For additional safety information, refer to the
Regulatory, Safety and Environmental Notices.
NOTE: When a device is connected to the jack, the
computer speakers are disabled.
The audio component must have a 4-conductor connector.
Operating system volume control:
a. Click the Volume icon in the notification area, at the far right of the taskbar.
b. Increase or decrease the volume by moving the slider up or down. Click the Mute icon to
mute the volume.
34 Chapter 5 Multimedia
– or –
a. Right-click the Volume icon in the notification area, and then click Open Volume Control.
b. In the Master column, increase or decrease the volume by moving the slider up or down.
You can also mute the volume by clicking the Mute icon.
Program volume control:
Volume can also be adjusted within some programs.

Using the media activity action keys

The media activity action keys control the play of an audio CD, or a DVD or BD that is inserted into an external optical drive (purchased separately).
NOTE: The external optical drive must be connected to a USB port on the computer, not to a USB
port on another external device, such as a hub or docking station.
When an audio CD, or a DVD or BD is not playing, press the play/pause action key (f6) (2) to
play the disc.
When an audio CD, or a DVD or BD is playing, use the following action keys:
To play the previous track of an audio CD or the previous chapter of a DVD or BD, press
the previous track action key (f5) (1).
To pause or resume playing the disc, press the play/pause action key (f6) (2).
To stop the disc, press the stop action key (f7) (3).
To play the next track of an audio CD or the next chapter of a DVD or BD, press the next
track action key (f8) (4).
Using the media activity action keys 35

Multimedia software

Your computer includes preinstalled multimedia software. Depending on the hardware and software included with the computer, the following multimedia tasks may be supported:
Playing digital media, including audio and video CDs, audio and video DVDs, and Internet radio
Creating or copying data CDs
Creating, editing, and burning audio CDs
Creating, editing, and burning a video or movie to a DVD or video CD

Using other preinstalled multimedia software

To locate other preinstalled multimedia software:
Select Computer > More Applications, and then open the multimedia program you want to
use.

Installing multimedia software from the Internet

To install multimedia software from the Internet, go to the software manufacturer’s Web site and
follow the instructions.
NOTE: Software downloaded from the Internet may contain viruses. Refer to the “Security” chapter
for more information.

Audio

Your computer has a variety of audio features that allow you to:
Play music using your computer speakers and/or connected external speakers.
Record sound using the internal microphone or an optional external headset microphone.
Download music from the Internet.
Create multimedia presentations using audio and images.
Transmit sound and images with instant messaging programs.

Connecting external audio devices

WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones,
earbuds, or a headset. For additional safety information, refer to the Regulatory, Safety and Environmental Notices.
To connect external devices such as external speakers, headphones, or a headset microphone, refer to the information provided with the device. For best results, remember the following tips:
Be sure that the device cable has a 4-conductor connector that supports both audio-out
(headphone) and audio-in (microphone).
Be sure that the external device cable is securely connected to the jack on your computer.
Be sure to install any drivers required by the external device.
36 Chapter 5 Multimedia
NOTE: A driver is a required program that acts like a translator between the device and the
programs that use the device.

Checking your audio functions

To check the system sound on your computer, follow these steps:
1. Select Computer > Control Center.
2. Click Sound.
3. When the Sound window opens, click the Sounds tab.
4. Under System Sounds, select the event for which you wish to hear the sound.
5. Select a sound from the list, and click the Sound icon located at the right of the event.
You should hear sound through the speakers or through connected headphones.
To check the record functions of the computer, follow these steps:
1. Select Computer > More Applications > Sound Recorder.
2. Click Record and speak into the microphone. Save the file to your desktop.
3. To play the sound, select Computer > More Applications.
4. Open an audio player, such as Helix Banshee, and play back the sound.
NOTE: For best results when recording, speak directly into the microphone and record sound in a
setting free of background noise.
To confirm or change the audio settings on your computer, right-click the Sound icon on the
taskbar.

Video

Your computer enables you to use a variety of video features:
Watch movies
Play games over the Internet
Edit pictures and video to create presentations
Connect external video devices

Connecting an external monitor or projector

Use a VGA cable (purchased separately) to connect an external display, such as a monitor or projector, to the external monitor port on the computer.
Video 37
To connect an external monitor or projector:
1. Connect the optional VGA cable to the external monitor port on the computer.
2. Connect the external monitor or projector to the other end of the cable.
NOTE: If a properly connected external monitor or projector does not display a screen image, press
the f4 action key to transfer the image to the external display. Repeatedly pressing f4 alternates the screen image between the external display and the computer.
38 Chapter 5 Multimedia

Webcam

Your computer includes an integrated webcam located at the top of the display. The webcam is an input device that allows you to record video and capture still photographs.
NOTE: Be sure that you have installed software that is designed for use with the integrated
webcam.
NOTE: For information about using software designed for use with the integrated webcam, refer to
the software help.
Webcam 39
6Security

Protecting the computer

Security features provided with your computer can protect the computer, personal information, and data from a variety of risks. The way you use your computer will determine which security features you need to use.
Follow the procedures in this chapter to use the following features:
Passwords
Built-in firewall software
Critical security updates
NOTE: Security solutions are designed to act as deterrents, but they may not deter software attacks
or prevent the computer from being mishandled or stolen.
NOTE: Before you send your computer for service, remove all password settings.
Computer risk Security feature
Unauthorized use of the computer Power-on password
Unauthorized access to data Firewall software
Unauthorized access to Setup Utility, BIOS settings, and other system identification information
Unauthorized access to a user account User password

Using passwords

A password is a group of characters that you choose to secure your computer information. Several types of passwords can be set, depending on how you want to control access to your information. Passwords can be set in the Setup Utility preinstalled on the computer.
CAUTION: To prevent being locked out of the computer, record each password you set. Because
most passwords are not displayed as they are set, changed, or deleted, it is essential to record each password immediately and store it in a secure place.
You can use the same password for a Setup Utility feature and for an operating system security feature. You can also use the same password for more than one Setup Utility feature.
Operating system updates
Administrator password
40 Chapter 6 Security
Use the following guidelines when setting a password in Setup Utility:
A password can be any combination of up to 8 letters and numbers and is case sensitive.
A password set in Setup Utility must be entered at a Setup Utility prompt.
Use the following tips for creating and saving passwords:
When creating passwords, follow requirements set by the program.
Write down your passwords and store them in a secure place away from the computer.
Do not store passwords in a file on the computer.
Do not use your name or other personal information that could be easily discovered by an
outsider.
The following sections list operating system and Setup Utility passwords and describe their functions.

Setting passwords in the operating system

Password Function
Root password Protects access to an operating system root-level account.
User password Protects access to an operating system user account.

Setting passwords in Setup Utility

Password Function
Administrator password* Protects access to Setup Utility.
Power-on password* Protects access to the computer contents.
*For details about each of these passwords, refer to the following topics.
Administrator password
Your administrator password protects the configuration settings and system identification information in Setup Utility. After this password is set, you must enter it each time you access Setup Utility.
After this password is set, it must be entered each time
you access Setup Utility.
CAUTION: If you forget your administrator password, you
cannot access Setup Utility.
After this password is set, it must be entered each time
you turn on or restart the computer, or exit Hibernation.
CAUTION: If you forget your power-on password, you
cannot turn on or restart the computer, or exit Hibernation.
Your administrator password is not interchangeable with an operating system root password, nor is it displayed as it is set, entered, changed, or deleted. Be sure that you record your password and store it in a safe place.
Using passwords 41
Managing an administrator password
To set, change, or delete this password, follow these steps:
1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
2. Use the arrow keys to select Security > Set Administrator Password, and then press enter.
To set an administrator password, type your password in the Enter New Password and
Confirm New Password fields, and then press enter.
To change an administrator password, type your current password in the Enter Current
Password field, type a new password in the Enter New Password and Confirm New Password fields, and then press enter.
To delete an administrator password, type your current password in the Enter Password
field, and then press enter 4 times.
3. To save your changes and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes.
Your changes go into effect when the computer restarts.
Entering an administrator password
At the Enter Password prompt, type your administrator password, and then press enter. After 3 unsuccessful attempts to enter the administrator password, you must restart the computer and try again.
Power-on password
Your power-on password prevents unauthorized use of the computer. After this password is set, it must be entered each time you turn on or restart the computer, or exit Hibernation. A power-on password is not displayed as it is set, entered, changed, or deleted.
Managing a power-on password
To set, change, or delete this password, follow these steps:
1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
2. Use the arrow keys to select Security > Set Power-On Password, and then press enter.
To set a power-on password, type your password in the Enter New Password and
Confirm New Password fields, and then press enter.
To change a power-on password, type your current password in the Enter Current
Password field, type a new password in the Enter New Password and Confirm New Password fields, and then press enter.
To delete a power-on password, type your current password in the Enter Current
Password field, and then press enter 4 times.
3. To save your changes and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes.
Your changes go into effect when the computer restarts.
42 Chapter 6 Security
Entering a power-on password
At the Enter Password prompt, type your password, and then press enter. After 3 unsuccessful attempts to enter the password, you must restart the computer and try again.
Using passwords 43

Using firewall software

When you use the computer for e-mail, network, or Internet access, unauthorized persons may be able to gain access to the computer, your personal files, and information about you. Use the firewall software preinstalled on the computer to protect your privacy.
Select Computer > Control Center > YaST > Security and Users > Firewall.
Firewall features include logging and reporting of network activity, and automatic monitoring of all incoming and outgoing traffic. Refer to the firewall user guide or contact your firewall manufacturer for more information.
NOTE: Under some circumstances a firewall can block access to Internet games, interfere with
printer or file sharing on a network, or block authorized e-mail attachments. To temporarily resolve the problem, disable the firewall, perform the task that you want to perform, and then reenable the firewall. To permanently resolve the problem, reconfigure the firewall.
44 Chapter 6 Security

Setting up automatic online updates

NOTE: You must have a network connection in order to receive automatic online updates.
To set up automatic online updates:
1. Select Computer > Control Center > YaST > Security and Users > Automatic Online
Update.
2. Select the Enable Automatic Update check box.
3. Select your preferred options for the automatic online update.
Setting up automatic online updates 45

7 Digital cards

Optional digital cards provide secure data storage and convenient data sharing. These cards are often used with digital media–equipped cameras and PDAs as well as with other devices.
The Digital Media Slot supports the following formats:
Memory Stick (MS)
MS/Pro
MultiMediaCard (MMC)
Secure Digital High Capacity (SDHC) Memory card (standard and large size)
xD-Picture card

Inserting a digital card

CAUTION: To avoid damaging the digital card or the computer, do not insert any type of adapter
into the Digital Media Slot.
CAUTION: To prevent damage to the digital card connectors, use minimal force to insert a digital
card.
1. Hold the digital card label-side up, with the connectors toward the computer.
2. Insert the card into the Digital Media Slot, and then push in on the card until it is firmly seated.
You will hear a sound when the device has been detected, and a menu of options may be displayed.
46 Chapter 7 Digital cards

Removing a digital card

CAUTION: To prevent loss of information or an unresponsive system, be sure that you are not
accessing the digital card before removal.
1. Save your information and close all programs associated with the digital card.
NOTE: Refer to the digital card user documentation for complete instructions on safe card
removal.
2. Press in on the digital card (1), and then remove the digital card from the slot (2).
Removing a digital card 47
8USB devices

Using a USB device

Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Devices can be connected to the system.
Some USB devices may require additional support software, which is usually included with the device. For more information about device-specific software, refer to the manufacturer's instructions.
The computer has 3 USB ports, which support USB 1.0, USB 1.1, and USB 2.0 devices. An optional USB hub provides additional USB ports that can be used with the computer.

Connecting a USB device

CAUTION: To prevent damage to a USB connector, use minimal force to connect a USB device.
To connect a USB device, connect the USB cable for the computer to the USB port.
You will hear a sound when the device has been detected.
NOTE: To view the USB devices installed on the computer, select Computer. Look under Status
for a list of installed USB devices.

Removing a USB device

CAUTION: To prevent loss of information or an unresponsive system, be sure that you are not
accessing a USB device before removal.
48 Chapter 8 USB devices
CAUTION: To prevent damage to a USB connector, do not pull on the cable to remove the USB
device.
Refer to the USB device user documentation for complete instructions on device removal.
Using a USB device 49

9 Pointing devices and keyboard

Using pointing devices

Using the TouchPad

To move the pointer, slide your finger across the TouchPad surface in the direction you want the pointer to go. Use the TouchPad buttons like the corresponding buttons on an external mouse. To scroll up and down using the TouchPad vertical scroll zone, slide your finger up or down over the lines.
NOTE: For more information on identifying the TouchPad components, refer to the “TouchPad”
section earlier in this guide.

Connecting an external mouse

You can connect an external USB mouse to the computer using one of the USB ports on the computer.

Using the keyboard

Using the action keys

Action keys are customized actions that are assigned to specific keys at the top of the keyboard.
To use an action key, press and hold this key to activate the assigned function.
NOTE: Depending on the program you are using, pressing fn and one of the action keys opens a
specific shortcut menu within that program.
NOTE: The action key feature is enabled at the factory. You can disable this feature in Setup Utility
and revert back to pressing the fn key and one of the action keys to activate the assigned function. Refer to the “Setup Utility” chapter for additional information.
Icon Description
f1 or fn + f1 Opens Gnome Desktop help.
50 Chapter 9 Pointing devices and keyboard
Icon Description
Decreases the screen brightness level incrementally when you hold down this key.
Increases the screen brightness level incrementally when you hold down this key.
Switches the screen image among display devices connected to the system. For example, if a monitor is connected to the computer, pressing this key alternates the screen image from computer display to monitor display to simultaneous display on both the computer and the monitor.
Most external monitors receive video information from the computer using the external VGA video standard. The f4 action key can also alternate images among other devices that are receiving video information from the computer.
Plays the previous track of a CD or the previous section of a DVD or BD.
Pauses or resumes playing the CD, DVD, or BD.
Stops playback of audio on a CD, or video on a DVD or BD.
Plays the next track of an audio CD or the next section of a DVD or BD.
Decreases speaker volume incrementally when you hold down this key.
prt sc Takes a snapshot or picture of your computer screen and copies it to the

Using hotkeys

The single hotkey combination is the fn key (1) and the esc key (2).
Increases speaker volume incrementally when you hold down this key.
Mutes or restores speaker sound.
Turns the wireless feature on or off.
NOTE: This key does not establish a wireless connection. To establish a
wireless connection, a wireless network must also be set up.
clipboard.
Using the keyboard 51
Function Hotkey Description
Display system information. fn+esc Displays information about system hardware
components and the system BIOS version number.
To use a hotkey command on the computer keyboard, follow either of these steps:
Briefly press the fn key, and then briefly press the second key of the hotkey command.
– or –
Press and hold down the fn key, briefly press the second key of the hotkey command, and then
release both keys at the same time.
52 Chapter 9 Pointing devices and keyboard

10 Drives

Identifying installed drives

To view the drives installed on the computer, click Computer > System Monitor > File
Systems.

Handling drives

Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply.
Identifying installed drives 53
CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information,
observe these precautions:
Before you move a computer that is connected to an external hard drive, initiate Sleep and allow the screen to clear, or properly disconnect the external hard drive.
Before handling a drive, discharge static electricity by touching the unpainted metal surface of the drive.
Do not touch the connector pins on a removable drive or on the computer.
Handle a drive carefully; do not drop a drive or place items on it.
Before removing or inserting a drive, shut down the computer. If you are unsure whether the computer is off, in the Sleep state, or in Hibernation, turn the computer on and then shut it down through the operating system.
Do not use excessive force when inserting a drive into a drive bay.
Do not type on the keyboard or move the computer while an optional optical drive is writing to a disc. The write process is sensitive to vibration.
When the battery is the only source of power, be sure that the battery is sufficiently charged before writing to media.
Avoid exposing a drive to temperature or humidity extremes.
Avoid exposing a drive to liquids. Do not spray the drive with cleaning products.
Remove media from a drive before removing the drive from the drive bay, or traveling with, shipping, or storing a drive.
If a drive must be mailed, place the drive in a bubble-pack mailer or other suitable protective packaging and label the package “FRAGILE.”
Avoid exposing a drive to magnetic fields. Security devices with magnetic fields include airport walk­through devices and security wands. The airport security devices that check carry-on luggage, such as conveyor belts, use X-rays instead of magnetism and will not damage a drive.

Using external drives

Removable external drives expand your options for storing and accessing information.
USB drives include the following types:
1.44-megabyte diskette drive
Hard drive module (a hard drive with an adapter attached)
DVD-ROM Drive
DVD/CD-RW Combo Drive
DVD+RW/R and CD-RW Combo Drive
DVD±RW/R and CD-RW Combo Drive
54 Chapter 10 Drives

Using optional external devices

NOTE: For more information about required software and drivers, or to learn which device port to
use, refer to the manufacturer's instructions.
To connect an external device:
CAUTION: To reduce the risk of damage to the equipment when connecting a powered device, be
sure that the computer is turned off and the AC power cord is unplugged.
1. Connect the device.
2. If you are connecting a powered device, plug the device power cord into a grounded AC outlet.
3. Turn on the computer.
To disconnect an unpowered external device, turn off the computer, and then disconnect it. To disconnect a powered external device, turn off the computer, disconnect it, and then unplug the AC power cord.
Using external drives 55

11 Memory modules

The computer has one memory module compartment, which is located on the bottom of the computer, beneath the vanity cover. The memory capacity of the computer can be upgraded by replacing the existing memory module in the memory module slot.
WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power
cord and remove all batteries before installing a memory module.
CAUTION: Electrostatic discharge (ESD) can damage electronic components. Before beginning
any procedure, ensure that you are discharged of static electricity by touching a grounded metal object.
To add or replace a memory module:
1. Save your work.
2. Shut down the computer and close the display.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by sliding the power switch. Then shut down the computer through the operating system.
3. Follow the instructions in the section “Removing the vanity cover,” earlier in this guide.
4. Unplug the power cord from the AC outlet.
5. Remove the existing memory module:
a. Pull away the retention clips (1) on each side of the memory module.
The memory module tilts up.
CAUTION: To prevent damage to the memory module, hold the memory module by the
edges only. Do not touch the components on the memory module.
56 Chapter 11 Memory modules
b. Grasp the edge of the memory module (2), and gently pull the module out of the memory
module slot.
To protect a memory module after removal, place it in an electrostatic-safe container.
6. Insert a new memory module:
CAUTION: To prevent damage to the memory module, hold the memory module by the edges
only. Do not touch the components on the memory module, and do not bend the memory module.
a. Align the notch (1) in the memory module with the tab in the memory module slot.
b. With the memory module at a 45-degree angle from the surface of the memory module
compartment, press the module (2) into the memory module slot until it is seated.
c. Gently press the memory module (3) down, applying pressure to both the left and right
edges of the memory module, until the retention clips snap into place.
CAUTION: To prevent damage to the memory module, be sure that you do not bend the
memory module.
7. Follow the instructions in the section “Replacing the vanity cover,” earlier in this guide.
57
8. Turn the computer right-side up, and then reconnect external power and external devices.
9. Turn on the computer.
58 Chapter 11 Memory modules

12 Setup Utility

Starting Setup Utility

Setup Utility is a ROM-based information and customization utility that can be used even when your operating system is not working.
The utility reports information about the computer and provides settings for startup, security, and other preferences.
To start Setup Utility:
Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.

Using Setup Utility

Changing the language of Setup Utility

The following procedure explains how to change the language of Setup Utility. If Setup Utility is not already running, begin at step 1. If Setup Utility is already running, begin at step 2.
1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
2. Use the arrow keys to select System Configuration > Language, and then press enter.
3. Use the arrow keys to select a language, and then press enter.
4. When a confirmation prompt with your language selected is displayed, press enter.
5. To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
Your change goes into effect immediately.

Navigating and selecting in Setup Utility

Because Setup Utility is not operating system based, it does not support the TouchPad. Navigation and selection are by keystroke.
To choose a menu or a menu item, use the arrow keys.
To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the
arrow keys or f5 or f6.
Starting Setup Utility 59
To select an item, press enter.
To close a text box or return to the menu display, press esc.
To display additional navigation and selection information while Setup Utility is open, press f1.

Displaying system information

The following procedure explains how to display system information in Setup Utility. If Setup Utility is not open, begin at step 1. If Setup Utility is open, begin at step 2.
1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
2. Select the Main menu. System information such as the system time and date, and identification
information about the computer is displayed.
3. To exit Setup Utility without changing any settings, use the arrow keys to select Exit > Exit
Discarding Changes, and then press enter.

Restoring default settings in Setup Utility

The following procedure explains how to restore the Setup Utility default settings. If Setup Utility is not already running, begin at step 1. If Setup Utility is already running, begin at step 2.
1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
2. Use the arrow keys to select Exit > Load Setup Defaults, and then press enter.
3. When the Setup Confirmation is displayed, press enter.
4. To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
The Setup Utility default settings go into effect when the computer restarts.
NOTE: Your password, security, and language settings are not changed when you restore the
factory default settings.

Exiting Setup Utility

You can exit Setup Utility with or without saving changes.
To exit Setup Utility and save your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow keys to select Exit > Exit Saving Changes, and then press enter.
To exit Setup Utility without saving your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow keys to select Exit > Exit Discarding Changes, and then press enter.
After either choice, the computer restarts.
60 Chapter 12 Setup Utility

Setup Utility menus

The menu tables in this section provide an overview of the Setup Utility options.
NOTE: Some of the Setup Utility menu items listed in this chapter may not be supported by your
computer.

Main menu

Select To do this
System information View and change the system time and date.

Security menu

Select To do this
Administrator password Enter, change, or delete an administrator password.
Power-On Password Enter, change, or delete a power-on password.
View identification information about the computer.
View specification information about the processor, memory size,
and system BIOS.

System Configuration menu

Select To do this
Language Support Change the Setup Utility language.
Processor C4 State Enable/disable the processor C4 sleep state.
Boot Options Set the following boot options:
f10 and f12 Delay (sec.)―Set the delay for the f10 and f12
functions of Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20).
HP Instant Web―Enable/disable the HP Instant Web menu in
Setup Utility.
Internal Network Adapter bootEnable/disable boot from Internal
Network Adapter.
Boot Device PrioritySet the boot device priority for:
Internal hard drive (select models only)
USB floppy
USB CD/DVD ROM drive
USB flash drive
USB Hard drive
Setup Utility menus 61
Select To do this

Diagnostics menu

Select To do this
Hard Disk Self Test (select models only) Run a comprehensive self-test on the hard drive.
Memory Test Run a diagnostic test on the system memory.
USB Card reader
Network adapter
NOTE: Only the devices attached to the system appear in
the boot order menu.
62 Chapter 12 Setup Utility

Index

A
AC adapter
connecting 16 identifying 12
action key
volume down 34 volume mute 33, 34
volume up 33, 34 action keys 4 administrator password
creating 42
entering 42
managing 42 airport security devices 54 antennas 11 audio devices, connecting
external 36 audio functions, checking 37 audio-in (microphone) jack 7, 34 audio-out (headphone) jack 7, 34
B
battery
calibrating 20 charging 18, 20 conserving power 22 discharging 19 disposing 23 identifying 12 inserting 17 low battery levels 19 recharging 22 removing 17
storing 22 battery bay, identifying 8 battery light 18 battery power 16 battery release latches 8, 17 battery temperature 22 bay, battery 8
Bluetooth device 26 boot options 61 boot order 61 buttons
left TouchPad 2 right TouchPad 2 TouchPad on/off button 2
C
cables
LAN 25 USB 48
VGA 38 calibrating battery 20 caps lock light, identifying 3 CD drive 54 changing Setup Utility
language 59 charging batteries 18, 20 checking audio functions 37 components
additional hardware 12 bottom 8 display 7 front 4 left-side 6 right-side 5
TouchPad 2 connecting to a WLAN 29 connection, external power 16 conservation, power 22 cord, power 12 corporate WLAN connection 29 critical battery level 19
D
Diagnostics menu 62 digital card
inserting 46
removing 47
diskette drive 54 display switch, identifying 7 displaying system information 60 drive media 14 drives
boot order 61 diskette 54 external 54 hard 54 optical 54
DVD drive 54
E
earbuds 7, 34 encryption 28 entering a power-on
password 43
entering an administrator
password 42 exiting Setup Utility 60 external audio devices,
connecting 36 external drive 54 external monitor port 37 external monitor port,
identifying 6
F
firewall 28 fn key 4, 51 function keys 51
H
hard drive self test 62 hard drive, external 54 hardware, identifying 2 headphone (audio-out) jack 7, 34 headphones 7, 34 Hibernation
exiting 14
Index 63
initiated during critical battery
level 19
initiating 14
hotkeys
description 51 using 52
hubs 48
I
icons
network 26 wired network 26 wireless 26
internal display switch,
identifying 7
internal microphone,
identifying 8, 33
Internet connection setup 28
J
jacks
audio-in (microphone) 7, 34 audio-out (headphone) 7, 34 RJ-45 (network) 6
K
keyboard hotkeys, identifying 51 keys
action 4 fn 4
L
labels
regulatory 13
serial number 12 language support 61 latches, battery release 8 left TouchPad button,
identifying 2
lights
caps lock 3
TouchPad 3
webcam 7 local area network (LAN)
cable required 25
connecting cable 25 low battery level 19
M
Main menu 61
managing a power-on
password 42
managing an administrator
password 42 Media Card Reader, identifying 5 memory module, removing 56 memory test 62 microphone (audio-in) jack 7, 34 monitor, connecting 37 mouse, external
connecting 50
multimedia components,
identifying 32 multimedia software
installing 36 using 36
N
navigating in Setup Utility 59 network cable
connecting 25
noise suppression circuitry 25 network icon 26 network jack, identifying 6 noise suppression circuitry,
network cable 25
O
operating system 23 operating system, passwords set
in 41
optical drive 54
P
passwords
administrator 41
power-on 42
set in Setup Utility 41
set in the operating system 41 ports
external monitor 37
USB 5, 7, 48 power
connecting 16
conserving 22 power connector, identifying 6 power cord, identifying 12 power-on password
creating 42
entering 43
managing 42
Processor C4 State 61 product name and number,
computer 12 projector, connecting 37 public WLAN connection 29
R
readable media 14 regulatory information
HP Mobile Broadband Module
serial number 13 regulatory label 13 wireless 13
release latches
battery 8, 18
restoring default settings 60 right TouchPad button,
identifying 2
RJ-45 (network) jack,
identifying 6
S
security cable slot 6 Security menu 61 security, wireless 28 selecting in Setup Utility 59 serial number, computer 12 setup of WLAN 28 Setup Utility, passwords set in 41 setup, computer 2 shut down 23 Sleep
exiting 14 initiating 14
software
installing 36 multimedia 36
speakers 4 speakers, identifying 33 storing battery 22 System Configuration menu 61 system information 61
T
temperature 22 TouchPad
buttons 2 identifying 2 using 50
TouchPad light, identifying 3
64 Index
TouchPad on/off button,
identifying 2 traveling with the computer 22 turning off the computer 23
U
unresponsive system 23 USB cable, connecting 48 USB devices
connecting 48 description 48
removing 48 USB hubs 48 USB ports, identifying 5, 7, 48
V
vanity cover
removing 8
replacing 10 vent, identifying 5, 6 volume down action key 34 volume down action key,
identifying 34 volume mute action key 34 volume mute action key,
identifying 33 volume up action key 34 volume up action key,
identifying 33 volume, adjusting 34
WLAN device 26 writable media 14 WWAN antennas, identifying 11
W
webcam light, identifying 7, 33 webcam, identifying 8, 33 wired network icon 26 wireless action key, identifying 26 wireless antennas 11 wireless controls
operating system 26 wireless icon 26 wireless light, identifying 26 wireless network (WLAN)
connecting 29
corporate WLAN
connection 29 equipment needed 28 functional range 29 public WLAN connection 29 security 28
wireless network, connecting 26 WLAN antennas, identifying 11
Index 65
Loading...