HP (Hewlett-Packard) MINI1101125NR User Manual

HP Mini User Guide

© Copyright 2009 Hewlett-Packard
Development Company, L.P.

Microsoft and Windows are U.S. registered
trademarks of Microsoft Corporation. SD
Logo is a trademark of its proprietor.

The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.

First Edition: September 2009

Document Part Number: 580592-001

Product notice

This user guide describes features that are
common to most models. Some features
may not be available on your computer.

To obtain the latest information in the Mini
User Guide, go to the HP Web site at

http://www.hp.com/support.

Safety warning notice

WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not

place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact
the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International
Standard for Safety of Information Technology Equipment (IEC 60950).

iii

iv Safety warning notice

Table of contents

1 Getting started

Using HP Instant Web (select models only) ......................................................................................... 2

2 Knowing the parts

Identifying the hardware ....................................................................................................................... 3

Top components .................................................................................................................. 3

TouchPad ............................................................................................................ 3

Light .................................................................................................................... 4

Keys .................................................................................................................... 5

Front components ................................................................................................................ 5

Right-side components ........................................................................................................ 7

Left-side components .......................................................................................................... 7

Display components ............................................................................................................ 8

Bottom components ............................................................................................................. 9

Wireless antennas ............................................................................................................. 10

Additional hardware components ...................................................................................... 11

Identifying the labels ........................................................................................................................... 11

3 Power management

Setting power options ......................................................................................................................... 13

Using power-saving states ................................................................................................. 13

Using power schemes ....................................................................................................... 14

Setting password protection upon exiting Standby ............................................................ 15

Using external AC power .................................................................................................................... 15

Connecting the AC adapter ............................................................................................... 16

Using battery power ........................................................................................................................... 16

Displaying the remaining battery charge ........................................................................... 17

Inserting or removing the battery ....................................................................................... 17

Charging a battery ............................................................................................................. 18

Initiating and exiting Standby ............................................................................ 13

Initiating and exiting Hibernation ....................................................................... 14

Viewing the current scheme .............................................................................. 14

Selecting a different power scheme .................................................................. 15

Customizing power schemes ............................................................................ 15

v

Maximizing battery discharge time .................................................................................... 19

Managing low battery levels .............................................................................................. 19

Identifying low battery levels ............................................................................. 19

Resolving a low battery level ............................................................................. 21

Resolving a low battery level when external power is available ....... 21

Resolving a low battery level when a charged battery is

available ........................................................................................... 21

Resolving a low battery level when no power source is

available ........................................................................................... 21

Resolving a low battery level when the computer cannot exit

Hibernation ....................................................................................... 21

Calibrating a battery ........................................................................................................... 21

Step 1: Fully charge the battery ........................................................................ 21

Step 2: Disable Hibernation and Standby ......................................................... 22

Step 3: Discharge the battery ............................................................................ 22

Step 4: Fully recharge the battery ..................................................................... 23

Step 5: Reenable Hibernation and Standby ...................................................... 23

Conserving battery power .................................................................................................. 23

Storing a battery ................................................................................................................ 23

Disposing of a used battery ............................................................................................... 24

Shutting down the computer ............................................................................................................... 24

4 Internet

Connecting to a wired network ........................................................................................................... 26

Connecting to a wireless network ....................................................................................................... 27

Using HP Mobile Broadband (select models only) ............................................................................. 33

Using the HP Mobile Broadband Setup Utility (select models only) ................................................... 36

5 Multimedia

Multimedia features ............................................................................................................................ 37

Using wireless devices ...................................................................................................... 27

Identifying wireless and network status icons ................................................... 27

Using the wireless controls ............................................................................... 28

Using the wireless switch .................................................................................. 28

Using HP Connection Manager software (select models only) ......................... 28

Using HP Wireless Assistant software .............................................................. 29

Using a WLAN ................................................................................................................... 29

Setting up a WLAN ............................................................................................ 30

Protecting your WLAN ....................................................................................... 30

Connecting to a WLAN ...................................................................................... 31

Roaming to another network ............................................................................. 32

Inserting a SIM ................................................................................................................... 33

Removing a SIM ................................................................................................................ 34

Identifying your multimedia components ........................................................................... 37

vi

6 Security

Adjusting the volume ......................................................................................................... 39

Multimedia software ........................................................................................................................... 40

Using other preinstalled multimedia software .................................................................... 40

Installing multimedia software from the Internet ................................................................ 40

Audio .................................................................................................................................................. 41

Connecting external audio devices .................................................................................... 41

Checking your audio functions ........................................................................................... 41

Video .................................................................................................................................................. 43

Connecting an external monitor or projector ...................................................................... 43

Webcam ............................................................................................................................................. 44

Protecting the computer ..................................................................................................................... 45

Using passwords ................................................................................................................................ 45

Passwords set in Windows ................................................................................................ 46

Passwords set in Setup Utility ........................................................................................... 46

Administrator password ..................................................................................... 47

Managing an administrator password ............................................... 47

Entering an administrator password ................................................. 47

Power-on password .......................................................................................... 47

Managing a power-on password ...................................................... 48

Entering a power-on password ......................................................... 48

Using antivirus software ..................................................................................................................... 49

Using firewall software ....................................................................................................................... 50

Installing critical updates .................................................................................................................... 51

7 Digital cards

Inserting a digital card ........................................................................................................................ 52

Stopping and removing a digital card ................................................................................................. 53

8 USB devices

Using a USB device ........................................................................................................................... 54

Connecting a USB device .................................................................................................. 54

Stopping and removing a USB device ............................................................................... 55

9 Pointing devices and keyboard

Setting pointing device preferences ................................................................................................... 56

Using pointing devices ....................................................................................................................... 56

Using the TouchPad .......................................................................................................... 56

Connecting an external mouse .......................................................................................... 56

Using the keyboard ............................................................................................................................ 56

Using hotkeys .................................................................................................................... 56

Initiating Standby ............................................................................................... 57

vii

10 Drives

Identifying installed drives .................................................................................................................. 60

Handling drives ................................................................................................................................... 60

Using external drives .......................................................................................................................... 61

Using optional external devices ......................................................................................... 62

11 Memory modules

12 Updating software

Updating the BIOS ............................................................................................................................. 68

Determining the BIOS version ........................................................................................... 68

Downloading a BIOS update ............................................................................................. 68

Updating programs and drivers .......................................................................................................... 70

Switching the screen ........................................................................................ 58

Decreasing screen brightness ........................................................................... 58

Increasing screen brightness ............................................................................ 58

Initiating QuickLock ........................................................................................... 58

Muting speaker sound ....................................................................................... 59

Decreasing speaker sound ............................................................................... 59

Increasing speaker sound ................................................................................. 59

13 Changing Instant Web Settings

Disabling and Enabling Instant Web .................................................................................................. 71

14 Setup Utility

Starting Setup Utility ........................................................................................................................... 72

Using Setup Utility .............................................................................................................................. 72

Changing the language of Setup Utility ............................................................................. 72

Navigating and selecting in Setup Utility ............................................................................ 72

Displaying system information ........................................................................................... 73

Restoring default settings in Setup Utility .......................................................................... 73

Exiting Setup Utility ............................................................................................................ 73

Setup Utility menus ............................................................................................................................ 74

Main menu ......................................................................................................................... 74

Security menu .................................................................................................................... 74

System Configuration menu .............................................................................................. 74

Diagnostics menu .............................................................................................................. 75

Index ................................................................................................................................................................... 76

viii

1 Getting started

Your HP computer's main operating system is Microsoft® Windows®. Your computer may also feature
the Instant Web application (select models only).

The Microsoft Windows operating system displays the desktop on the display and controls your

●

HP computer's hardware, peripherals, and software programs.

If your computer includes Instant Web, it launches within seconds of pressing the power button. It

●

allows you to quickly browse the Internet, view digital photos, listen to music, or keep in touch using
e-mail, instant messages, or Skype (select models only), without having to boot your main operating
system. Instant Web is also referred to as Instant-On Software (IOS).

NOTE: Instant Web is enabled by default. To disable or reenable Instant Web, refer to Chapter 13,

"Changing Instant Web settings." You can access the software Help in Instant Web by clicking the Help
icon in the notification area.

1

Using HP Instant Web (select models only)

To start Instant Web:

Turn on your computer. The HP Instant Web screen appears.

●

Click an icon on the Instant Web screen to launch a program.

●

To start Instant Web from Microsoft Windows:

Select Start, click the arrow next to the Shut down button, and then click Restart. Your computer

▲

restarts and displays the Instant Web home page.

NOTE: To learn more about HP Instant Web, refer to the software Help included with Instant Web.

2 Chapter 1 Getting started

2 Knowing the parts

Identifying the hardware

Components included with the computer may vary by region and model. The illustrations in this chapter
identify the standard features on most computer models.

To see a list of hardware installed in the computer, follow these steps:

1. Select Start > My Computer.

2. In the left pane of the System Tasks window, select View system information.

3. Select Hardware tab > Device Manager.

You can also add hardware or modify computer configurations using Device Manager.

Top components

TouchPad

Component Description

(1) Left TouchPad button* Functions like the left button on an external mouse.

(2) TouchPad* Moves the pointer and selects or activates items on the

(3) TouchPad scroll zone Scrolls up or down.

screen.

Identifying the hardware 3

Light

(4) Right TouchPad button* Functions like the right button on an external mouse.

*This table describes factory settings. To view or change pointing device preferences, select Start > Control Panel > Printers
and Other Hardware > Mouse.

Component Description

Caps lock light On: Caps lock is on.

4 Chapter 2 Knowing the parts

Keys

Component Description

(1) Function keys Execute frequently used system functions when

(2) fn key Executes frequently used system functions when

(3) Windows® logo key Displays the Windows Start menu.

(4) Windows applications key Displays a shortcut menu for items beneath the

Front components

pressed in combination with the fn key.

pressed in combination with a function key.

pointer.

Identifying the hardware 5

Component Description

(1) Power light

(2) Power switch

(3) Drive light Blinking: The hard drive or flash drive is being

(4) Battery light

On: The computer is on.

●

Blinking: The computer is in Standby.

●

Off: The computer is off or in Hibernation.

●

When the computer is off, slide the switch to turn

●

on the computer.

When the computer is on, briefly slide the switch

●

to initiate Hibernation.

When the computer is in Standby, briefly slide

●

the switch to exit Standby.

When the computer is in Hibernation, briefly

●

slide the switch to exit Hibernation.

If the computer has stopped responding and
Windows shutdown procedures are ineffective, slide
and hold the power switch for at least 5 seconds to
turn off the computer.

To learn more about your power settings, select

Start > Control Panel > Performance and
Maintenance > Power Options.

accessed.

On: A battery is charging.

●

Blinking: A battery that is the only available

●

power source has reached a low battery level.
When the battery reaches a critical battery level,
the battery light begins blinking rapidly.

Off: If the computer is plugged into an external

●

power source, the light turns off when all
batteries in the computer are fully charged. If the
computer is not plugged into an external power
source, the light stays off until the battery
reaches a low battery level.

(5) Wireless light

(6) Wireless switch Turns the wireless feature on or off, but does not

Blue: An integrated wireless device, such as a

●

wireless local area network (WLAN) device, is
on.

Amber: All wireless devices are off.

●

establish a wireless connection.

NOTE: A wireless network must be set up in order

to establish a wireless connection.

6 Chapter 2 Knowing the parts

Right-side components

Component Description

(1) USB ports (2) Connect optional USB devices.

(2) Digital Media Slot Supports the following optional digital card formats:

Memory Stick (MS)

●

MS/Pro

●

MultiMediaCard (MMC)

●

Secure Digital (SD) Memory Card

●

(3) External monitor port Connects an optional external display, such as a

(4) RJ-45 (network) jack Connects a network cable.

Left-side components

Component Description

(1) Security cable slot Attaches an optional security cable to the computer.

xD-Picture card

●

monitor or projector, to the computer.

NOTE: The security cable is designed to act as a

deterrent, but it may not prevent the computer from
being mishandled or stolen.

Identifying the hardware 7

Component Description

(2) Power connector Connects an AC adapter.

(3) AC adapter light On: The computer is connected to external power.

Off: The computer is not connected to external power.

(4) Vent Enables airflow to cool internal components.

NOTE: The computer fan starts up automatically to

cool internal components and prevent overheating. It
is normal for the internal fan to cycle on and off during
routine operation.

(5) USB port Connects an optional USB device.

(6) Audio-out (headphone) jack/Audio-in (microphone)

jack

Display components

Produces sound when connected to optional powered
stereo speakers, headphones, earbuds, a headset, or
television audio. Also connects an optional headset
microphone.

WARNING! To reduce the risk of personal injury,

adjust the volume before putting on headphones,
earbuds, or a headset. For additional safety
information, refer to the Regulatory, Safety and

Environmental Notices.

NOTE: When an audio component is connected to

the jack, the computer speakers are disabled.

The audio component cable must have a 4-conductor
connector.

Component Description

(1) Speakers (2) Produce sound.

8 Chapter 2 Knowing the parts

Component Description

(2) Internal display switch Turns off the display if the display is closed while the

(3) Webcam Captures still photographs and videos.

(4) Webcam light On: The webcam is in use.

(5) Internal microphone Records sound.

Bottom components

power is on.

NOTE: The display switch is not visible from the

outside of the computer.

NOTE: To capture videos, you need to install additional

webcam software.

Component Description

(1) Battery bay Holds the battery.

(2) Battery release latches (2) Release the battery from the battery bay.

Identifying the hardware 9

Component Description

(3) Vent Enables airflow to cool internal components.

(4) Memory module compartment Contains the memory module slot.

Wireless antennas

NOTE: The computer fan starts up automatically to cool

internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.

Component Description

(1) WWAN antennas (2) (select models only)* Send and receive wireless signals to communicate with wireless

(2) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless

*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around
the antennas free from obstructions.

To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental

Notices that applies to your country or region. To access these notices, click Start > Help and
Support > User Guides.

10 Chapter 2 Knowing the parts

wide-area networks (WWANs).

local area networks (WLANs).

Additional hardware components

Component Description

(1) Power cord* Connects an AC adapter to an AC outlet.

(2) AC adapter Converts AC power to DC power.

(3) Battery* Powers the computer when the computer is not plugged into

*Batteries and power cords vary in appearance by region and country.

Identifying the labels

The labels affixed to the computer provide information you may need when you troubleshoot system
problems or travel internationally with the computer.

Service tag—Provides important information including the following:

●

Product name (1). This is the product name affixed to the front of your computer.

◦

Serial number (s/n) (2). This is an alphanumeric identifier that is unique to each product.

◦

Part Number/Product number (p/n) (3). This number provides specific information about the

◦

hardware components of the product. The part number helps a service technician to determine
what components and parts are needed.

external power.

Model description (4). This is the alphanumeric identifier you use to locate documents, drivers,

◦

and support for your computer.

Warranty period (5). This number describes the duration (in years) of the warranty period for

◦

this computer.

Identifying the labels 11

Have this information available when you contact technical support. The service tag label is affixed
to the bottom of the computer.

Microsoft® Certificate of Authenticity—Contains the Windows® Product Key. You may need the

●

Product Key to update or troubleshoot the operating system. This certificate is affixed to the bottom
of the computer.

Regulatory label—Provides regulatory information about the computer, including the following:

●

Information about optional wireless devices and the approval markings of some of the

◦

countries or regions in which the devices have been approved for use. An optional device may
be a wireless local area network (WLAN) device. You may need this information when
traveling internationally.

The serial number of your HP Mobile Broadband Module (select models only).

◦

The regulatory label is affixed to the bottom of the computer.

12 Chapter 2 Knowing the parts

3 Power management

Setting power options

Using power-saving states

The computer has two power-saving states enabled at the factory: Standby and Hibernation.

When Standby is initiated, the power light blinks and the screen clears. Your work is saved to memory.
Exiting Standby is faster than exiting Hibernation. If the computer is in Standby for an extended period
or if the battery reaches a critical battery level while in Standby, the computer initiates Hibernation.

When Hibernation is initiated, your work is saved to a hibernation file on the hard drive and the computer
turns off.

CAUTION: To prevent possible audio and video degradation, loss of audio or video playback

functionality, or loss of information, do not initiate Standby or Hibernation while reading from or writing
to a disc or an external media card.

NOTE: You cannot initiate any type of networking connection or perform any computer functions while

the computer is in Standby or in Hibernation.

Initiating and exiting Standby

The system is set at the factory to initiate Standby after 10 minutes of inactivity when running on battery
power and 25 minutes of inactivity when running on external power.

Power settings and timeouts can be changed using Power Options in Windows Control Panel.

With the computer on, you can initiate Standby in any of the following ways:

Press fn+f1.

●

Click Start > Turn Off Computer > Stand By.

●

To exit Standby:

Briefly slide the power switch.

▲

When the computer exits Standby, the power light turns on and your work returns to the screen
where you stopped working.

NOTE: If you have set a password to be required when the computer exits Standby, you must enter

your Windows password before your work will return to the screen.

Setting power options 13

Initiating and exiting Hibernation

The system is set at the factory to initiate Hibernation after 30 minutes of inactivity when running on
battery power or when the battery reaches a critical battery level.

NOTE: The system will not initiate Hibernation when running on external power.

NOTE: To reduce the risk of information loss, periodically save your work.

Power settings and timeouts can be changed using Power Options in Windows Control Panel.

To initiate Hibernation:

1. Select Start > Turn Off Computer.

2. Hold down the shift key and select Hibernate.

– or –

If the computer is on, briefly slide the power switch.

▲

To exit Hibernation:

Briefly slide the power switch.

▲

When the computer exits Hibernation, the power light turns on and your work returns to the screen where
you stopped working.

NOTE: If you have set a password to be required when the computer exits Hibernation, you must enter

your Windows password before your work will return to the screen.

Using power schemes

A power scheme is a collection of system settings that manages how the computer uses power. Power
schemes can help you conserve power and maximize computer performance.

The following power schemes are available:

Portable/Laptop (recommended)

●

Home/Office Desk

●

Presentation

●

Always On

●

Minimal Power Management

●

Max Battery

●

You can change the settings of these power plans through Power Options.

Viewing the current scheme

Click the Power Meter icon in the notification area, at the far right of the taskbar.

▲

– or –

Select Start > Control Panel > Performance and Maintenance > Power Options.

14 Chapter 3 Power management

Selecting a different power scheme

Click the Power Meter icon in the notification area, at the far right of the taskbar, and then select

▲

a power scheme from the list.

– or –

a. Select Start > Control Panel > Performance and Maintenance > Power Options.

b. Select a power scheme from the Power schemes list.

c. Click OK.

Customizing power schemes

1. Select Start > Control Panel > Performance and Maintenance > Power Options.

2. Select a power scheme from the Power schemes list.

3. Modify the Plugged in and Running on batteries settings as needed.

4. Click OK.

Setting password protection upon exiting Standby

To set the computer to prompt for a password when the computer exits Standby, follow these steps:

1. Right-click the Power Meter icon in the notification area, and then click Adjust Power

Properties.

2. Click the Advanced tab.

3. Select the Prompt for password when computer resumes from standby check box.

4. Click Apply.

Using external AC power

External AC power is supplied through one of the following devices:

WARNING! To reduce potential safety issues, use only the AC adapter provided with the computer,

a replacement AC adapter provided by HP, or a compatible AC adapter purchased from HP.

Approved AC adapter

●

Optional docking device or optional expansion product

●

Connect the computer to external AC power under any of the following conditions:

WARNING! Do not charge the computer battery while you are onboard aircraft.

When you are charging or calibrating a battery

●

When you are installing or modifying system software

●

When you are writing information to a CD or DVD

●

Using external AC power 15

When you connect the computer to external AC power, the following events occur:

The battery begins to charge.

●

If the computer is turned on, the battery meter icon in the notification area changes appearance.

●

When you disconnect external AC power, the following events occur:

The computer switches to battery power.

●

The display brightness is automatically decreased to save battery life. To increase display

●

brightness, press the fn+f4 hotkey or reconnect the AC adapter.

Connecting the AC adapter

WARNING! To reduce the risk of electric shock or damage to the equipment:

Plug the power cord into an AC outlet that is easily accessible at all times.

Disconnect power from the computer by unplugging the power cord from the AC outlet (not by
unplugging the power cord from the computer).

If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3­pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The
grounding pin is an important safety feature.

To connect the computer to external AC power, follow these steps:

1. Plug the AC adapter into the power connector (1) on the computer.

2. Plug the power cord into the AC adapter (2).

3. Plug the other end of the power cord into an AC outlet (3).

Using battery power

When a charged battery is in the computer and the computer is not plugged into external power, the
computer runs on battery power. When the computer is plugged into external AC power, the computer
runs on AC power.

16 Chapter 3 Power management

If the computer contains a charged battery and is running on external AC power supplied through the
AC adapter, the computer switches to battery power if the AC adapter is disconnected from the
computer.

NOTE: The display brightness is decreased to save battery life when you disconnect AC power. To

increase display brightness, use the fn+f4 hotkey or reconnect the AC adapter.

You can keep a battery in the computer or in storage, depending on how you work. Keeping the battery
in the computer whenever the computer is plugged into AC power charges the battery and also protects
your work in case of a power outage. However, a battery in the computer slowly discharges when the
computer is off and unplugged from external power.

WARNING! To reduce potential safety issues, use only the battery provided with the computer, a

replacement battery provided by HP, or a compatible battery purchased from HP.

Computer battery life varies, depending on power management settings, programs running on the
computer, display brightness, external devices connected to the computer, and other factors.

Displaying the remaining battery charge

Double-click the Power Meter icon in the notification area, at the far right of the taskbar.

▲

– or –

Select Start > Control Panel > Performance and Maintenance > Power Options > Power
Meter tab.

Most charge indicators report battery status as both a percentage and as the number of minutes of
charge remaining:

The percentage indicates the approximate amount of charge remaining in the battery.

●

The time indicates the approximate running time remaining on the battery if the battery continues

●

to provide power at the current level. For example, the time remaining will decrease when a DVD
is playing and will increase when a DVD stops playing.

When a battery is charging, a lightning bolt icon may be superimposed over the battery icon on the
Power Meter screen.

Inserting or removing the battery

CAUTION: Removing a battery that is the sole power source may cause loss of information. To prevent

loss of information, save your work and initiate Hibernation or shut down the computer through Windows
before removing the battery.

To insert the battery:

1. Turn the computer upside down on a flat surface.

Using battery power 17

2. Align the tabs on the battery with the notches on the computer, and then insert the battery into the

battery bay. The battery release latches automatically lock the battery into place.

To remove the battery:

1. Turn the computer upside down on a flat surface.

2. Slide the battery release latches (1) to release the battery, and then remove the battery (2).

Charging a battery

WARNING! Do not charge the computer battery while you are onboard aircraft.

The battery charges whenever the computer is plugged into external power through an AC adapter, an
optional power adapter, an optional docking device, or an optional expansion product.

The battery charges whether the computer is off or in use, but it charges faster when the computer is
off.

18 Chapter 3 Power management

Charging may take longer if a battery is new, has been unused for 2 weeks or more, or is much warmer
or cooler than room temperature.

To prolong battery life and optimize the accuracy of battery charge displays, follow these
recommendations:

If you are charging a new battery, charge it fully before turning on the computer.

●

Charge the battery until the battery light turns off.

●

NOTE: If the computer is on while the battery is charging, the battery meter in the notification

area may show 100 percent charge before the battery is fully charged.

Allow the battery to discharge below 5 percent of a full charge through normal use before charging

●

it.

If the battery has been unused for one month or more, calibrate the battery instead of simply

●

charging it.

The battery light displays charge status:

On: The battery is charging.

●

Blinking: The battery that is the only available power source has reached a low battery level. When

●

the battery reaches a critical battery level, the battery light begins blinking rapidly.

Off: The battery is fully charged, in use, or not installed.

●

Maximizing battery discharge time

Battery discharge time varies depending on the features you use while on battery power. Maximum
discharge time gradually shortens, as the battery storage capacity naturally degrades.

Tips for maximizing battery discharge time:

Decrease the brightness on the display.

●

Remove the battery from the computer when it is not being used or charged.

●

Store the battery in a cool, dry location.

●

Managing low battery levels

The information in this section describes the alerts and system responses set at the factory. Some low­battery alerts and system responses can be changed using Power Options in Windows Control Panel.
Preferences set using Power Options do not affect lights.

Identifying low battery levels

When a battery that is the sole power source for the computer reaches a low battery level, the battery
light blinks.

If a low battery level is not resolved, the computer enters a critical battery level, and the battery light
blinks rapidly.

Using battery power 19

The computer takes the following actions for a critical battery level:

If Hibernation is enabled and the computer is on or in Standby, the computer initiates Hibernation.

●

If Hibernation is disabled and the computer is on or in Standby, the computer remains briefly in

●

Standby, and then shuts down and loses any unsaved information.

20 Chapter 3 Power management

Resolving a low battery level

CAUTION: To reduce the risk of losing information when the computer reaches a critical battery level

and has initiated Hibernation, do not restore power until the power lights turn off.

Resolving a low battery level when external power is available

Connect one of the following devices:

▲

AC adapter

●

Optional expansion product or docking device

●

Optional power adapter

●

Resolving a low battery level when a charged battery is available

1. Turn off the computer or initiate Hibernation.

2. Remove the discharged battery, and then insert a charged battery.

3. Turn on the computer.

Resolving a low battery level when no power source is available

Initiate Hibernation.

▲

– or –

Save your work and shut down the computer.

Resolving a low battery level when the computer cannot exit Hibernation

When the computer lacks sufficient power to exit Hibernation, follow these steps:

1. Insert a charged battery or plug the computer into external power.

2. Exit Hibernation by briefly sliding the power switch.

Calibrating a battery

Calibrate a battery under the following conditions:

When battery charge displays seem inaccurate

●

When you observe a significant change in battery run time

●

Even if a battery is heavily used, it should not need to be calibrated more than once a month. It is also
not necessary to calibrate a new battery.

Step 1: Fully charge the battery

WARNING! Do not charge the computer battery while you are onboard aircraft.

NOTE: The battery charges whether the computer is off or in use, but it charges faster when the

computer is off.

Using battery power 21

To fully charge the battery:

1. Insert the battery into the computer.

2. Connect the computer to an AC adapter, optional power adapter, optional expansion product, or

optional docking device, and then plug the adapter or device into external power.

The battery light on the computer turns on.

3. Leave the computer plugged into external power until the battery is fully charged.

The battery light on the computer turns off.

Step 2: Disable Hibernation and Standby

1. Right-click the Power Meter icon in the notification area, at the far right of the taskbar, and then

click Adjust Power Properties.

– or –

Select Start > Control Panel > Performance and Maintenance > Power Options.

2. Record the 4 settings listed in the Running on batteries column and the Plugged in column so

that you can reset them after the calibration.

3. Set the 4 options to Never.

4. Click OK.

Step 3: Discharge the battery

The computer must remain on while the battery is being discharged. The battery can discharge whether
or not you are using the computer, but the battery will discharge faster while you are using it.

If you plan to leave the computer unattended during the discharge, save your information before

●

beginning the discharge procedure.

If you use the computer occasionally during the discharge procedure and have set energy-saving

●

timeouts, expect the following performance from the system during the discharge process:

The monitor will not turn off automatically.

◦

Hard drive speed will not decrease automatically when the computer is idle.

◦

System-initiated Hibernation will not occur.

◦

To discharge a battery:

1. Unplug the computer from its external power source, but do not turn off the computer.

2. Run the computer on battery power until the battery is discharged. The battery light begins to blink

when the battery has discharged to a low battery level. When the battery is discharged, the battery
light turns off and the computer shuts down.

22 Chapter 3 Power management

Step 4: Fully recharge the battery

To recharge the battery:

1. Plug the computer into external power and maintain external power until the battery is fully

recharged. When the battery is recharged, the battery light on the computer turns off.

You can use the computer while the battery is recharging, but the battery will charge faster if the
computer is off.

2. If the computer is off, turn it on when the battery is fully charged and the battery light has turned

off.

Step 5: Reenable Hibernation and Standby

CAUTION: Failure to reenable Hibernation after calibration may result in a full battery discharge and

information loss if the computer reaches a critical battery level.

1. Select Start > Control Panel > Performance and Maintenance > Power Options.

2. Reenter the settings that you recorded for the items in the Plugged in column and the Running

on batteries column.

3. Click OK.

Conserving battery power

Select low power-use settings through Power Options in Windows Control Panel.

●

Turn off wireless and local area network (LAN) connections and exit modem applications when you

●

are not using them.

Disconnect external devices that are not plugged into an external power source, when you are not

●

using them.

Stop, disable, or remove any external media cards that you are not using.

●

Use the fn+f3 and fn+f4 hotkeys to adjust screen brightness as needed.

●

If you leave your work, initiate Standby or Hibernation, or shut down the computer.

●

Storing a battery

CAUTION: To prevent damage to a battery, do not expose it to high temperatures for extended periods

of time.

If a computer will be unused and unplugged from external power for more than 2 weeks, remove the
battery and store it separately.

To prolong the charge of a stored battery, place it in a cool, dry place.

NOTE: A stored battery should be checked every 6 months. If the capacity is less than 50 percent,

recharge the battery before returning it to storage.

Calibrate a battery before using it if it has been stored for one month or more.

Using battery power 23

Disposing of a used battery

WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short

external contacts; do not dispose of in fire or water.

Refer to the Regulatory, Safety and Environmental Notices for battery disposal information.

Shutting down the computer

CAUTION: Unsaved information will be lost when the computer is shut down.

The Shut Down command closes all open programs, including the operating system, and then turns off
the display and computer.

Shut down the computer under any of the following conditions:

When you need to replace the battery or access components inside the computer

●

When you are connecting an external hardware device that does not connect to a USB port

●

When the computer will be unused and disconnected from external power for an extended period

●

To shut down the computer, follow these steps:

NOTE: If the computer is in Standby or in Hibernation, you must first exit Standby or Hibernation before

shutdown is possible.

1. Save your work and close all open programs.

2. Select Start > Turn Off Computer > Turn Off.

If the computer is unresponsive and you are unable to use the preceding shutdown procedures, try the
following emergency procedures in the sequence provided:

Press ctrl+alt+delete. Then, click Shut Down > Turn Off.

●

Slide and hold the power switch for at least 5 seconds.

●

Disconnect the computer from external power and remove the battery.

●

24 Chapter 3 Power management

4Internet

Your computer supports the following types of Internet access:

Wired—You can access the Internet by connecting to a broadband network using the RJ-45

●

(network) jack.

Wireless—For mobile Internet access, you can use a wireless connection. To learn about setting

●

up a wireless network or adding your computer to an existing network, refer to the “Connecting to
a wireless network” section.

25

Connecting to a wired network

Connecting to a local area network (LAN) requires an 8-pin, RJ-45 network cable (purchased
separately). If the network cable contains noise suppression circuitry (1), which prevents interference
from TV and radio reception, orient the circuitry end of the cable (2) toward the computer.

To connect the network cable:

WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a modem

cable or telephone cable into an RJ-45 (network) jack.

1. Plug the network cable into the network jack (1) on the computer.

2. Plug the other end of the cable into a network wall jack (2).

26 Chapter 4 Internet

Connecting to a wireless network

Using wireless devices

Wireless technology transfers data across radio waves instead of wires. Your computer may be
equipped with one or more of the following wireless devices:

Wireless local area network (WLAN) device—Connects the computer to wireless local area

●

networks (commonly referred to as Wi-Fi networks, wireless LANs, or WLANs) in corporate offices,
your home, and public places such as airports, restaurants, coffee shops, hotels, and universities.
In a WLAN, each mobile wireless device communicates with a wireless router or a wireless access
point.

HP Mobile Broadband Module (select models only)—A wireless wide area network (WWAN) device

●

that provides access to information wherever mobile network operator service is available. In a
WWAN, each mobile device communicates to a mobile network operator’s base station. Mobile
network operators install networks of base stations (similar to cell phone towers) throughout large
geographic areas, effectively providing coverage across entire states, regions, or even countries.

The device supports the following IEEE industry standards:

802.11b, the first popular standard, supports data rates of up to 11 Mbps and operates at a

●

frequency of 2.4 GHz.

802.11g supports data rates of up to 54 Mbps and operates at a frequency of 2.4 GHz. An 802.11g

●

WLAN device is backward compatible with 802.11b devices, so they can operate on the same
network.

For more information on wireless technology, refer to the information and Web site links provided in
Help and Support.

Identifying wireless and network status icons

Icon Name Description

Wireless (connected) Identifies the location of the wireless light and the wireless switch

Wireless (disconnected) Indicates that all of the wireless devices are off.

Wireless network connection (connected) Indicates that one or more of your WLAN devices are connected

Wireless network connection (disconnected) Indicates that one or more of your WLAN devices are not

on the computer. Also identifies that one or more of the wireless
devices are on.

to the network.

connected to a network.

Connecting to a wireless network 27

Network status (connected) Indicates that one or more of your LAN drivers are installed and

Network status (disconnected) Indicates that one or more of your LAN drivers are installed but

Using the wireless controls

You can control the wireless devices in your computer using these features:

Wireless switch

●

Operating system controls

●

Using the wireless switch

The computer has a wireless switch, one or more wireless devices, and one wireless light. All of the
wireless devices on your device are enabled at the factory, so the wireless light is on (blue) when you
turn on the computer.

one or more LAN devices are connected to the network.

no LAN devices are connected to the network.

The wireless light indicates the overall power state of your wireless devices, not the status of individual
devices. If the wireless light is blue, at least one wireless device is on. If the wireless light is amber, all
wireless devices are off.

Because the wireless devices are enabled at the factory, you can use the wireless switch to turn on or
turn off all of the wireless devices simultaneously.

Using HP Connection Manager software (select models only)

Connection Manager allows you to manage your Internet profiles, SMS (Short Message Service)
messaging, connection devices and methods, and edit additional settings.

To start Connection Manager:

1. Click the HP Connection Manager icon in the notification area, at the far right of the taskbar.

2. Click Connect to turn on the wireless wide area network (WWAN) feature and use HP Mobile

Broadband.

NOTE: Connection time varies. After the connection is established, a notification message is

displayed in the Connection Manager window.

NOTE: Connection Manager is minimized when first opened. To maximize the Connection Manager

window and view more information on connectivity status, click Details.

For more details about using Connection Manager, refer to the Connection Manager Help.

28 Chapter 4 Internet

Using HP Wireless Assistant software

A wireless device can be turned on or off using the Wireless Assistant software. If a wireless device is
disabled by Setup Utility, it must be reenabled by Setup Utility before it can be turned on or off using
Wireless Assistant.

NOTE: Enabling or turning on a wireless device does not automatically connect the computer to a

network.

To view the state of the wireless devices, position the mouse pointer over the wireless icon in the
notification area, at the far right of the taskbar.

NOTE: To display the wireless icon, click the Show hidden icons icon (< or <<) in the notification

area.

If the wireless icon is not displayed in the notification area, complete the following steps to change
Wireless Assistant properties:

1. Click Start > Control Panel > Network and Internet Connections > HP Wireless Assistant.

2. Click Properties.

3. Select the check box next to Wireless Assistant icon in notification area.

4. Click Apply.

For more information, refer to the Wireless Assistant software Help:

1. Open Wireless Assistant by double-clicking the icon in the notification area.

2. Click the Help button.

You can use the properties dialog box in Wireless Assistant to show the on/off controls for each installed
wireless device and control the devices separately. To show the on/off controls:

1. Double-click the Wireless Assistant icon in the notification area, at the far right of the taskbar.

2. Click Properties.

3. Select the Independent controls for installed wireless devices check box, and then click

Apply.

4. Click Turn off or Turn on to control each wireless device separately.

Using a WLAN

With a WLAN device, you can access a wireless local area network (WLAN), which is composed of other
devices and accessories that are linked by a wireless router or a wireless access point.

NOTE: The terms wireless router and wireless access point are often used interchangeably.

A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points

●

that can accommodate a large number of devices and accessories and can separate critical
network functions.

A home or small office WLAN typically uses a wireless router, which allows several wireless and

●

wired devices to share an Internet connection, a printer, and files without requiring additional pieces
of hardware or software.

Connecting to a wireless network 29

To use the WLAN device in your computer, you must connect to a WLAN infrastructure (provided through
a service provider or a public or corporate network).

Setting up a WLAN

To set up a WLAN and connect to the Internet, you need the following equipment:

A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an

●

Internet service provider (ISP)

A wireless router (purchased separately) (2)

●

The wireless device (3)

●

The illustration below shows an example of a wireless network installation that is connected to the
Internet.

As your network grows, additional wireless and wired devices can be connected to the network to access
the Internet.

For help in setting up your WLAN, refer to the information provided by your router manufacturer or your
ISP.

Protecting your WLAN

It is essential to understand that because the WLAN standard was designed with only limited security
capabilities—basically to foil casual eavesdropping rather than more powerful forms of attack—WLANs
are vulnerable to well-known and well-documented security weaknesses.

WLANs in public areas, or “hotspots,” like coffee shops and airports may not provide any security. New
technologies are being developed by wireless manufacturers and hotspot service providers that make
the public environment more secure and anonymous. If you are concerned about the security of your
computer in a hotspot, limit your network activities to noncritical e-mail and basic Internet surfing.

When you set up a WLAN or access an existing WLAN, always enable security features to protect your
network from unauthorized access. The common security levels are Wi-Fi Protected Access (WPA)­Personal and Wired Equivalent Privacy (WEP). Because wireless radio signals travel outside the
network, other WLAN devices can pick up unprotected signals and either connect to your network

30 Chapter 4 Internet

(uninvited) or capture information being sent across it. However, you can take precautions to protect
your WLAN:

Use a wireless transmitter with built-in security

●

Many wireless base stations, gateways, or routers provide built-in security features such as
wireless security protocols and firewalls. With the correct wireless transmitter, you can protect your
network from the most common wireless security risks.

Work behind a firewall

●

A firewall is a barrier that checks both data and requests for data that are sent to your network,
and discards any suspicious items. Firewalls are available in many varieties, both software and
hardware. Some networks use a combination of both types.

Use wireless encryption

●

A variety of sophisticated encryption protocols is available for your WLAN. Find the solution that
works best for your network security:

Wired Equivalent Privacy (WEP) is a wireless security protocol that encodes or encrypts all

◦

network data before it is transmitted using a WEP key. Usually, you can allow the network to
assign the WEP key. Alternatively, you can set up your own key, generate a different key, or
choose other advanced options. Without the correct key, others will not be able to use the
WLAN.

WPA (Wi-Fi Protected Access), like WEP, uses security settings to encrypt and decrypt data

◦

that is transmitted over the network. However, instead of using one static security key for
encryptions as WEP does, WPA uses “temporal key integrity protocol” (TKIP) to dynamically
generate a new key for every packet. It also generates different sets of keys for each device
on the network.

Close your network

●

If possible, prevent your network name (SSID) from being broadcast by the wireless transmitter.
Most networks initially broadcast the name, telling any device nearby that your network is available.
By closing the network, other devices are less likely to know that your network exists.

NOTE: If your network is closed and the SSID is not broadcast, you will need to know or remember

the SSID to connect new devices to the network. Write down the SSID and store it in a secure
place before closing the network.

Connecting to a WLAN

To connect to the WLAN, follow these steps:

1. Be su r e t h a t t he WLAN device is on. If it is on, the wireless light is blue. If the wireless light is amber,

slide the wireless switch.

2. Select Start > Connect to.

3. Select your WLAN from the list, and then type the network security key, if required.

If the network is unsecured, meaning that anyone can access the network, a warning is

●

displayed. Click Connect Anyway to accept the warning and complete the connection.

If the network is a security-enabled WLAN, you are prompted to enter a network security key,

●

which is a security code. Type the code, and then click Connect to complete the connection.

Connecting to a wireless network 31

NOTE: If no WLANs are listed, you are out of range of a wireless router or access point.

NOTE: If you do not see the network you want to connect to, click Set up a connection or

network. A list of options is displayed. You can choose to manually search for and connect to a

network or to create a new network connection.

4. After the connection is made, place the mouse pointer over the wireless network connection icon

in the notification area, at the far right of the taskbar, to verify the name, speed, strength, and status
of the connection.

NOTE: The functional range (how far your wireless signals travel) depends on WLAN implementation,

router manufacturer, and interference from other electronic devices or structural barriers such as walls
and floors.

More information about using a WLAN is available through the following resources:

Information from your ISP and the user guides included with your wireless router and other WLAN

●

equipment

Information and Web site links provided in Help and Support

●

For a list of public WLANs near you, contact your ISP or search the Web. Web sites that list public
WLANs include Cisco Internet Mobile Office Wireless Locations, Hotspotlist, and Geektools. Check with
each public WLAN location for cost and connection requirements.

Roaming to another network

When you move your computer within range of another WLAN, Windows attempts to connect to that
network. If the attempt is successful, your computer is automatically connected to the new network. If
Windows does not recognize the new network, follow the same procedure you used initially to connect
to your WLAN.

32 Chapter 4 Internet

Using HP Mobile Broadband (select models only)

An HP Mobile Broadband Module is a wireless wide area network (WWAN) device that provides access
to information wherever mobile network operator service is available. Using HP Mobile Broadband
requires a network service provider (called a mobile network operator), which in most cases is a mobile
phone network operator. Coverage for HP Mobile Broadband is similar to mobile phone voice coverage.

When used with mobile network operator service, HP Mobile Broadband gives you the freedom to stay
connected to the Internet, send e-mail, or connect to your corporate network whether you are on the
road or outside the range of Wi-Fi hotspots.

HP Mobile Broadband supports the following technologies:

HSPA (High Speed Packet Access) module, which provides access to networks based on the

●

Global System for Mobile Communications (GSM) telecommunications standard.

EV-DO (Evolution Data Optimized), which provides access to networks based on the code division

●

multiple access (CDMA) telecommunications standard.

You may need the HP Mobile Broadband Module serial number to activate mobile broadband service.
The serial number is printed on a label inside the battery bay of your computer. Some mobile network
operators require the use of a subscriber identity module (SIM). A SIM contains basic information about
you, such as a personal identification number (PIN), as well as network information. Some computers
include a SIM that is preinstalled in the battery bay. If the SIM is not preinstalled, it may be provided in
the packet of HP Mobile Broadband information provided with your computer, or the mobile network
operator may provide it separately from the computer.

For information on inserting and removing the SIM, refer to the “Inserting a SIM” and “Removing a SIM”
sections in this chapter.

For information on HP Mobile Broadband and how to activate service with a preferred mobile network
operator, refer to the HP Mobile Broadband information included with your computer. For additional
information, see the HP Web site at

Inserting a SIM

CAUTION: When inserting a SIM, position the card with the slanted corner as shown in the illustration.

If a SIM is inserted backwards or upside down, the battery may not snap into place properly and could
damage the SIM and the SIM connector. To prevent damage to the connectors, use minimal force when
inserting a SIM.To prevent damage to the connectors, use minimal force when inserting a SIM.

To insert a SIM:

1. Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn the

computer on by pressing the power button. Then shut down the computer through the operating
system.

2. Close the display.

3. Disconnect all external devices connected to the computer.

4. Unplug the power cord from the AC outlet.

http://www.hp.com/go/mobilebroadband (US only).

5. Turn the computer upside down on a flat surface, with the battery bay toward you.

6. Remove the battery.

Using HP Mobile Broadband (select models only) 33

7. Insert the SIM into the SIM slot, and gently push the SIM into the slot until it is firmly seated.

8. Replace the battery.

NOTE: HP Mobile Broadband will be disabled if the battery is not replaced.

9. Reconnect external power.

10. Reconnect external devices.

11. Turn on the computer.

Removing a SIM

To remove a SIM:

1. Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn the

computer on by pressing the power button. Then shut down the computer through the operating
system.

2. Close the display.

3. Disconnect all external devices connected to the computer.

4. Unplug the power cord from the AC outlet.

5. Turn the computer upside down on a flat surface, with the battery bay toward you.

6. Remove the battery.

34 Chapter 4 Internet

7. Press in on the SIM (1), and then remove it from the slot (2).

8. Replace the battery.

9. Reconnect external power.

10. Reconnect external devices.

11. Turn on the computer.

Using HP Mobile Broadband (select models only) 35

Using the HP Mobile Broadband Setup Utility (select models only)

The HP Mobile Broadband Setup Utility provides basic information about setting up HP Mobile
Broadband.

NOTE: The HP Mobile Broadband Setup Utility is not available in all regions.

When you first turn on HP Mobile Broadband, the Getting Started with HP Mobile Broadband page
opens.

36 Chapter 4 Internet

5Multimedia

Multimedia features

Your computer includes multimedia features that allow you to listen to music, watch movies, and view
pictures. Your computer may include the following multimedia components:

Integrated speakers for listening to music

●

Integrated webcam that allows you to capture photographs and videos

●

Preinstalled multimedia software that allows you to play and manage your music, movies, and

●

pictures

NOTE: Your computer may not include all of the components listed.

The following sections explain how to identify and use the multimedia components included with your
computer.

Identifying your multimedia components

The following illustration and table describe the multimedia features of the computer.

Multimedia features 37

Component Description

(1) Webcam Captures still photographs and videos.

NOTE: To capture videos, you need to install additional

webcam software.

(2) Webcam light On: The webcam is in use.

(3) Internal microphone Records sound.

(4) Speakers (2) Produce sound.

(5) Volume up hotkey Increases speaker sound when pressed in combination with

the fn key.

(6) Volume down hotkey Decreases speaker sound when pressed in combination with

the fn key.

(7) Volume mute hotkey Mutes speaker sound when pressed in combination with the

fn key.

(8) Audio-out (headphone) jack/Audio-in

(microphone) jack

38 Chapter 5 Multimedia

Produces sound when connected to optional powered stereo
speakers, headphones, earbuds, a headset, or television
audio. Also connects an optional headset microphone.

WARNING! To reduce the risk of personal injury, adjust the

volume before putting on headphones, earbuds, or a headset.
For additional safety information, refer to the Regulatory,

Safety and Environmental Notices.

NOTE: When a device is connected to the jack, the

computer speakers are disabled.

The audio component must have a 4-conductor connector.

Adjusting the volume

You can adjust the volume using the following controls:

computer volume hotkey—A combination of the fn key (1) and either the f8 (2), f10 (3), or f11 (4)

●

function key:

To mute or restore volume, press fn+f8.

◦

To decrease volume, press fn+f10.

◦

To increase volume, press fn+f11.

◦

Windows® volume control:

●

a. Click the Volume icon in the notification area, at the far right of the taskbar.

b. Increase or decrease the volume by moving the slider up or down. Select the Mute check box

to mute the volume.

– or –

a. Double-click the Volume icon in the notification area.

b. In the Speakers column, you can increase or decrease the volume by moving the slider up or

down. You can also adjust the balance or mute the volume.

Multimedia features 39

If the Volume icon is not displayed in the notification area, follow these steps to add it:

a. Select Start > Control Panel > Sounds, Speech, and Audio Devices > Sounds and Audio

Devices > Volume tab.

b. Select the Place volume icon in the taskbar check box.

c. Click Apply.

Program volume control:

●

Volume can also be adjusted within some programs.

Multimedia software

Your computer includes preinstalled multimedia software that allows you to play music, watch movies,
and view pictures.

Using other preinstalled multimedia software

To locate other preinstalled multimedia software:

Select Start > All Programs, and then open the multimedia program you want to use. For example,

▲

if you want to use Windows Media Player (select models only), click Windows Media Player.

NOTE: Some programs may be located in subfolders.

Installing multimedia software from the Internet

To install multimedia software from the Internet, go to the software manufacturer’s Web site and

▲

follow the instructions.

NOTE: Software downloaded from the Internet may contain viruses. Refer to the “Security” chapter

for more information.

40 Chapter 5 Multimedia

Audio

Your computer has a variety of audio features that allow you to:

Play music using your computer speakers and/or connected external speakers.

●

Record sound using the internal microphone or an optional external headset microphone.

●

Download music from the Internet.

●

Create multimedia presentations using audio and images.

●

Transmit sound and images with instant messaging programs.

●

Connecting external audio devices

WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones,

earbuds, or a headset. For additional safety information, refer to the Regulatory, Safety and
Environmental Notices.

To connect external devices such as external speakers, headphones, or a headset microphone, refer
to the information provided with the computer. For best results, remember the following tips:

Be sure that the device cable has a 4-conductor connector that supports both audio-out

●

(headphone) and audio-in (microphone).

Be sure that the external device cable is securely connected to the jack on your computer.

●

Be sure to install any drivers required by the external device.

●

NOTE: A driver is a required program that acts like a translator between the device and the

programs that use the device.

Checking your audio functions

To check the system sound on your computer, follow these steps:

1. Select Start > Control Panel > Sounds, Speech, and Audio Devices > Sounds and Audio

Devices.

2. When the Sound and Audio Device Properties window opens, click the Sounds tab. Under

Program events, select any sound event, such as a beep or alarm, and click the arrow button to

check the sound.

You should hear sound through the speakers or through connected headphones.

To check the record functions of the computer, follow these steps:

1. Select Start > All Programs > Accessories > Entertainment > Sound Recorder.

2. Click the record button and speak into the microphone. Save the file to your desktop.

3. Open a multimedia program and play back the sound.

Audio 41

NOTE: For best results when recording, speak directly into the microphone and record sound in a

setting free of background noise.

To confirm or change the audio settings on your computer, right-click the Volume icon on the

▲

taskbar, or select Start > Control Panel > Sounds, Speech, and Audio Devices > Sounds and
Audio Devices.

42 Chapter 5 Multimedia

Video

Your computer enables you to use a variety of video features:

Watch movies

●

Play games over the Internet

●

Edit pictures and video to create presentations

●

Connect external video devices

●

Connecting an external monitor or projector

Use a VGA cable (purchased separately) to connect an external display, such as a monitor or projector,
to the external monitor port on the computer.

To connect an external monitor or projector:

1. Connect the optional VGA cable to the external monitor port on the computer.

2. Connect the external monitor or projector to the other end of the cable.

NOTE: If a properly connected external monitor or projector does not display a screen image, press

fn+f2 to transfer the image to the external display. Repeatedly pressing fn+f2 alternates the screen

image between the external display and the computer.

Video 43

Webcam

Your computer includes an integrated webcam, located at the top of the display. The webcam is an input
device that allows you to capture still photographs and videos.

NOTE: To record videos, you need to install additional webcam software.

To access the webcam:

1. Click Start > My Computer, and then double-click the camera icon.

2. Click Take a new picture to take a picture.

NOTE: The picture is automatically saved in the My Documents folder.

44 Chapter 5 Multimedia

6Security

Protecting the computer

Standard security features provided by the Windows operating system and the non-Windows Setup
Utility can protect your personal settings and data from a variety of risks.

Follow the procedures in this chapter to use the following features:

Passwords

●

Firewall software

●

Antivirus support (Norton Internet Security)

●

Critical security updates

●

NOTE: Security solutions are designed to act as deterrents, but they may not deter software attacks

or prevent the computer from being mishandled or stolen.

NOTE: Before you send your computer for service, remove all password settings.

Device risk Security feature

Unauthorized use of the computer

Unauthorized access to data

Unauthorized access to Setup Utility, BIOS settings, and other
system identification information

Ongoing or future threats to the computer Critical security updates from Microsoft

Unauthorized access to a Windows user account User password

Using passwords

A password is a group of characters that you choose to secure your computer information. Several types
of passwords can be set, depending on how you want to control access to your information. Passwords
can be set in Windows or in the non-Windows Setup Utility preinstalled on the computer.

CAUTION: To prevent being locked out of the computer, record each password you set. Because

most passwords are not displayed as they are set, changed, or deleted, it is essential to record each
password immediately and store it in a secure place.

QuickLock

●

Power-on password

●

Firewall software

●

Windows updates

●

Administrator password

Protecting the computer 45

You can use the same password for a Setup Utility feature and for a Windows security feature. You can
also use the same password for more than one Setup Utility feature.

Use the following guidelines when setting a password in Setup Utility:

A password can be any combination of up to 8 letters and numbers and is case sensitive.

●

A password set in Setup Utility must be entered at a Setup Utility prompt. A password set

●

in Windows must be entered at a Windows prompt.

Use the following tips for creating and saving passwords:

When creating passwords, follow requirements set by the program.

●

Write down your passwords and store them in a secure place away from the computer.

●

Do not store passwords in a file on the computer.

●

Do not use your name or other personal information that could be easily discovered by an outsider.

●

The following sections list Windows and Setup Utility passwords and describe their functions. For
additional information about Windows passwords, such as screen-saver passwords, select Start > Help

and Support.

Passwords set in Windows

Password Function

Administrator password Protects administrator-level access to computer contents.

User password Protects access to a Windows user account. It also protects

QuickLock Protects the computer by requiring a password to be entered

Passwords set in Setup Utility

Password Function

Administrator password*

NOTE: This password cannot be used to access Setup Utility

contents.

access to the computer contents and must be entered when
you exit Standby or Hibernation.

in the Windows Log On dialog box before you access the
computer. After you set a user or administrator password,
follow these steps:

1. Initiate QuickLock by pressing fn+f6.

2. Exit QuickLock by entering your Windows user or

administrator password.

Protects access to Setup Utility.

●

After this password is set, it must be entered each time

●

you access Setup Utility.

46 Chapter 6 Security

CAUTION: If you forget your administrator password, you

cannot access Setup Utility.

Password Function

Power-on password*

*For details about each of these passwords, refer to the following topics.

Administrator password

Your administrator password protects the configuration settings and system identification information in
Setup Utility. After this password is set, you must enter it each time you access Setup Utility.

Your administrator password is not interchangeable with an administrator password set in Windows,
nor is it displayed as it is set, entered, changed, or deleted. Be sure that you record your password and
store it in a safe place.

Managing an administrator password

To set, change, or delete this password, follow these steps:

1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10

= BIOS Setup Options” message is displayed in the lower-left corner of the screen.

Protects access to the computer contents.

●

After this password is set, it must be entered each time

●

you turn on or restart the computer, or exit Hibernation.

CAUTION: If you forget your power-on password, you

cannot turn on or restart the computer, or exit Hibernation.

2. Use the arrow keys to select Security > Set Administrator Password, and then press enter.

To set an administrator password, type your password in the Enter New Password and

●

Confirm New Password fields, and then press enter.

To change an administrator password, type your current password in the Enter Current

●

Password field, type a new password in the Enter New Password and Confirm New
Password fields, and then press enter.

To delete an administrator password, type your current password in the Enter Password field,

●

and then press enter 4 times.

3. To save your changes and exit Setup Utility, use the arrow keys to select Exit > Exit Saving

Changes.

Your changes go into effect when the computer restarts.

Entering an administrator password

At the Enter Password prompt, type your administrator password, and then press enter. After 3
unsuccessful attempts to enter the administrator password, you must restart the computer and try again.

Power-on password

Your power-on password prevents unauthorized use of the computer. After this password is set, it must
be entered each time you turn on or restart the computer, or exit Hibernation. A power-on password is
not displayed as it is set, entered, changed, or deleted.

Using passwords 47

Managing a power-on password

To set, change, or delete this password, follow these steps:

1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10

= BIOS Setup Options” message is displayed in the lower-left corner of the screen.

2. Use the arrow keys to select Security > Set Power-On Password, and then press enter.

To set a power-on password, type your password in the Enter New Password and Confirm

●

New Password fields, and then press enter.

To change a power-on password, type your current password in the Enter Current

●

Password field, type a new password in the Enter New Password and Confirm New
Password fields, and then press enter.

To delete a power-on password, type your current password in the Enter Current

●

Password field, and then press enter 4 times.

3. To save your changes and exit Setup Utility, use the arrow keys to select Exit > Exit Saving

Changes.

Your changes go into effect when the computer restarts.

Entering a power-on password

At the Enter Password prompt, type your password, and then press enter. After 3 unsuccessful attempts
to enter the password, you must restart the computer and try again.

48 Chapter 6 Security

Using antivirus software

When you use the computer for e-mail or Internet access, you expose it to computer viruses that can
disable the operating system, programs, or utilities or cause them to function abnormally.

Antivirus software can detect most viruses, destroy them, and in most cases, repair damage they have
caused. To provide ongoing protection against newly discovered viruses, antivirus software must be
kept up to date.

Norton Internet Security, an antivirus program, is preinstalled on the computer.

Your version of Norton Internet Security includes 60 days of free updates. It is strongly

●

recommended that you protect the computer against new viruses beyond 60 days by purchasing
extended update service. Instructions for using and updating Norton Internet Security software and
for purchasing extended update service are provided within the program.

To access Norton Internet Security, or to get more information about it, click Start > All

●

Programs > Norton Internet Security.

NOTE: HP recommends that you always update the antivirus software to help protect your computer.

NOTE: For more information about computer viruses, type viruses in the Search box in Help and

Support.

Using antivirus software 49

Using firewall software

When you use the computer for e-mail, network, or Internet access, unauthorized persons may be able
to gain access to the computer, your personal files, and information about you. Use the firewall software
preinstalled on the computer to protect your privacy.

Firewall features include logging and reporting of network activity, and automatic monitoring of all
incoming and outgoing traffic. Refer to the firewall user guide or contact your firewall manufacturer for
more information.

NOTE: Under some circumstances a firewall can block access to Internet games, interfere with printer

or file sharing on a network, or block authorized e-mail attachments. To temporarily resolve the problem,
disable the firewall, perform the task that you want to perform, and then reenable the firewall. To
permanently resolve the problem, reconfigure the firewall.

50 Chapter 6 Security

Installing critical updates

CAUTION: Microsoft sends alerts regarding critical updates. To protect the computer from security

breaches and computer viruses, install all critical updates from Microsoft as soon as you receive an
alert.

Updates to the operating system and other software may have become available after the computer
was shipped. To be sure that all available updates are installed on the computer, observe these
guidelines:

Run Windows Update as soon as possible after you set up your computer. Use the update link at

●

Start > All Programs > Windows Update.

Run Windows Update at regular intervals, such as once a month.

●

Obtain updates to Windows and other Microsoft programs, as they are released, from the Microsoft

●

Web site and through the updates link in Help and Support.

Installing critical updates 51

7 Digital cards

Optional digital cards provide secure data storage and convenient data sharing. These cards are often
used with digital media–equipped cameras and PDAs as well as with other devices.

The Digital Media Slot supports the following formats:

Memory Stick (MS)

●

MS/Pro

●

MultiMediaCard (MMC)

●

Secure Digital (SD) Memory Card

●

xD-Picture card

●

Inserting a digital card

CAUTION: To avoid damaging the digital card or the computer, do not insert any type of adapter into

the Digital Media Slot.

CAUTION: To prevent damage to the digital card connectors, use minimal force to insert a digital card.

1. Hold the digital card label-side up, with the connectors facing the computer.

2. Insert the card into the Digital Media Slot, and then push in on the card until it is firmly seated.

You will hear a sound when the device has been detected, and a menu of options may be displayed.

52 Chapter 7 Digital cards

Stopping and removing a digital card

CAUTION: To prevent loss of data or an unresponsive system, stop a digital card before removing it.

1. Save your information and close all programs associated with the digital card.

NOTE: To stop a data transfer, click Cancel in the operating system Copying window.

2. Stop the digital card:

a. Double-click the Safely Remove Hardware icon in the notification area, at the far right of the

taskbar.

NOTE: To display the Safely Remove Hardware icon, click the Show Hidden Icons icon

(< or <<) in the notification area.

b. Click the name of the digital card in the list.

c. Click Stop, and then click OK.

3. Press in on the digital card (1), and then remove the card from the slot (2).

Stopping and removing a digital card 53

8USB devices

Using a USB device

Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external
device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Devices can be connected to
the system, an optional docking device, or an optional expansion product.

Some USB devices may require additional support software, which is usually included with the device.
For more information about device-specific software, refer to the manufacturer's instructions.

The computer has 3 USB ports, which support USB 1.0, USB 1.1, and USB 2.0 devices. An optional
USB hub, optional docking device, or an optional expansion product provides additional USB ports that
can be used with the computer.

Connecting a USB device

CAUTION: To prevent damage to a USB connector, use minimal force to connect a USB device.

To connect a USB device, connect the USB cable for the device to the USB port.

▲

You will hear a sound when the device has been detected.

NOTE: When you connect a USB device, you may see a message in the notification area to let you

know that the device is recognized by the system.

54 Chapter 8 USB devices

Stopping and removing a USB device

CAUTION: To prevent loss of information or an unresponsive system, stop a USB device before

removing it.

CAUTION: To prevent damage to a USB connector, do not pull on the cable to remove the USB device.

To stop and remove a USB device:

1. Double-click the Safely Remove Hardware icon in the notification area, at the far right of the

taskbar.

NOTE: To display the Safely Remove Hardware icon, click the Show Hidden Icons icon (< or

<<) in the notification area.

2. Click the name of the device in the list.

NOTE: If the USB device is not listed, you do not have to stop the device before you remove it.

3. Click Stop, and then click OK.

4. Remove the device.

Using a USB device 55

9 Pointing devices and keyboard

Setting pointing device preferences

Use Mouse Properties in Windows® to customize settings for pointing devices, such as button
configuration, click speed, and pointer options.

To access Mouse Properties, select Start > Control Panel > Printers and Other Hardware >

Mouse.

Using pointing devices

Using the TouchPad

To move the pointer, slide your finger across the TouchPad surface in the direction you want the pointer
to go. Use the TouchPad buttons like the corresponding buttons on an external mouse. To scroll up and
down using the TouchPad vertical scroll zone, slide your finger up or down over the lines.

NOTE: If you are using the TouchPad to move the pointer, you must lift your finger off the TouchPad

before moving it to the scroll zone. Simply sliding your finger from the TouchPad to the scroll zone will
not activate the scrolling function.

Connecting an external mouse

You can connect an external USB mouse to the computer using one of the USB ports on the
computer.

Using the keyboard

Using hotkeys

Hotkeys are combinations of the fn key (1) and one of the function keys (2).

The icons on the f1 through f4, and f6, f8, f10, and f11 keys represent the hotkey functions. Hotkey
functions and procedures are discussed in the following sections.

56 Chapter 9 Pointing devices and keyboard

Function Hotkey

Initiate Standby. fn+f1

Switch the image. fn+f2

Decrease screen brightness. fn+f3

Increase screen brightness. fn+f4

Initiate QuickLock. fn+f6

Mute or restore speaker. fn+f8

Decrease speaker sound. fn+f10

Increase speaker sound. fn+f11

To use a hotkey command on the computer keyboard, follow either of these steps:

Briefly press the fn key, and then briefly press the second key of the hotkey command.

●

– or –

Press and hold down the fn key, briefly press the second key of the hotkey command, and then

●

release both keys at the same time.

Initiating Standby

Press fn+f1 to initiate Standby.

When Standby is initiated, your information is stored in memory, the screen is cleared, and power is
conserved. While the computer is in Standby, the power light blinks.

Using the keyboard 57

CAUTION: To reduce the risk of information loss, save your work before initiating Standby.

The computer must be on before you can initiate Standby.

NOTE: If a critical battery level occurs while the computer is in Standby, the computer initiates

Hibernation and the information stored in memory is saved to the hard drive. The factory setting for
critical battery action is Hibernate, but this setting can be changed in advanced power settings.

To exit Standby, briefly slide the power switch.

The function of the fn+f1 hotkey can be changed. For example, you can set the fn+f1 hotkey to initiate
Hibernation instead of Standby.

NOTE: In all Windows operating system windows, references to the sleep button apply to the fn+f1

hotkey.

Switching the screen

Press fn+f2 to switch the screen image among display devices connected to the system. For example,
if a monitor is connected to the computer, pressing fn+f2 alternates the screen image from computer
display to monitor display to simultaneous display on both the computer and the monitor.

NOTE: You must use a VGA cable (purchased separately) to connect an external display, such as a

monitor or projector, to the external monitor port on the computer.

Most external monitors receive video information from the computer using the external VGA video
standard. The fn+f2 hotkey can also alternate images among other devices receiving video information
from the computer.

The following video transmission types, with examples of devices that use them, are supported by the

fn+f2 hotkey:

LCD (device display)

●

External VGA (most external monitors)

●

Decreasing screen brightness

Press fn+f3 to decrease screen brightness. Hold down the hotkey to decrease the brightness level
incrementally.

Increasing screen brightness

Press fn+f4 to increase screen brightness. Hold down the hotkey to increase the brightness level
incrementally.

Initiating QuickLock

Press fn+f6 to initiate the QuickLock security feature.

QuickLock protects your information by displaying the operating system Log On window. While the Log
On window is displayed, the computer cannot be accessed until a Windows user password or a Windows
administrator password is entered.

NOTE: Before you can use QuickLock, you must set a Windows user password or a Windows

administrator password. For instructions, refer to Help and Support.

58 Chapter 9 Pointing devices and keyboard

To use QuickLock, press fn+f6 to display the Log On window and lock the computer. Then follow the
instructions on the screen to enter your Windows user password or your Windows administrator
password and access the computer.

Muting speaker sound

Press fn+f8 to mute speaker sound. Press the hotkey again to restore speaker sound.

Decreasing speaker sound

Press fn+f10 to decrease speaker sound. Hold down the hotkey to decrease speaker sound
incrementally.

Increasing speaker sound

Press fn+f11 to increase speaker sound. Hold down the hotkey to increase speaker sound
incrementally.

Using the keyboard 59

10 Drives

Identifying installed drives

To view the drives installed on the computer, select Start > My Computer.

Handling drives

Drives are fragile computer components that must be handled with care. Refer to the following cautions
before handling drives. Additional cautions are included with the procedures to which they apply.

60 Chapter 10 Drives

CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information,

observe these precautions:

Before you move a computer that is connected to an external hard drive, initiate Standby and allow the
screen to clear, or properly disconnect the external hard drive.

Before handling a drive, discharge static electricity by touching the unpainted metal surface of the drive.

Do not touch the connector pins on a removable drive or on the computer.

Handle a drive carefully; do not drop a drive or place items on it.

Before removing or inserting a drive, shut down the computer. If you are unsure whether the computer
is off, in Standby, or in Hibernation, turn the computer on and then shut it down through the operating
system.

Do not use excessive force when inserting a drive into a drive bay.

Do not type on the keyboard or move the computer while an optional optical drive is writing to a disc.
The write process is sensitive to vibration.

When the battery is the only source of power, be sure that the battery is sufficiently charged before
writing to media.

Avoid exposing a drive to temperature or humidity extremes.

Avoid exposing a drive to liquids. Do not spray the drive with cleaning products.

Remove media from a drive before removing the drive from the drive bay, or traveling with, shipping, or
storing a drive.

If a drive must be mailed, place the drive in a bubble-pack mailer or other suitable protective packaging
and label the package “FRAGILE.”

Avoid exposing a drive to magnetic fields. Security devices with magnetic fields include airport walk­through devices and security wands. The airport security devices that check carry-on luggage, such as
conveyor belts, use X-rays instead of magnetism and will not damage a drive.

Using external drives

Removable external drives expand your options for storing and accessing information .

USB drives include the following types:

1.44-megabyte diskette drive

●

Hard drive module (a hard drive with an adapter attached)

●

DVD-ROM Drive

●

DVD/CD-RW Combo Drive

●

DVD+RW/R and CD-RW Combo Drive

●

DVD±RW/R and CD-RW Combo Drive

●

Using external drives 61

Using optional external devices

NOTE: For more information about required software and drivers, or to learn which computer port to

use, refer to the manufacturer's instructions.

To connect an external device:

CAUTION: To reduce the risk of damage to the equipment when connecting a powered device, be

sure that the computer is turned off and the AC power cord is unplugged.

1. Connect the device.

2. If you are connecting a powered device, plug the device power cord into a grounded AC outlet.

3. Turn on the computer.

To disconnect an unpowered external device, turn off the computer, and then disconnect it. To
disconnect a powered external device, turn off the computer, disconnect it, and then unplug the AC
power cord.

62 Chapter 10 Drives

11 Memory modules

The computer has one memory module compartment, which is located on the bottom of the computer.
The memory capacity of the computer can be upgraded by replacing the existing memory module in the
primary memory module slot.

WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord

and remove all batteries before installing a memory module.

CAUTION: Electrostatic discharge (ESD) can damage electronic components. Before beginning any

procedure, ensure that you are discharged of static electricity by touching a grounded metal object.

To add or replace a memory module:

1. Save your work.

2. Shut down the computer and close the display.

If you are not sure whether the computer is off or in Hibernation, turn the computer on by sliding
the power switch. Then shut down the computer through the operating system.

3. Disconnect all external devices connected to the computer.

4. Unplug the power cord from the AC outlet.

5. Turn the computer upside down on a flat surface.

6. Remove the battery from the computer.

7. Using a small Phillips screwdriver, loosen the 2 cover screws (1).

63

8. Lift the memory module compartment cover (2) away from the computer.

9. Remove the existing memory module:

a. Pull away the retention clips (1) on each side of the memory module.

The memory module tilts up.

CAUTION: To prevent damage to the memory module, hold the memory module by the

edges only. Do not touch the components on the memory module.

b. Grasp the edge of the memory module (2), and gently pull the module out of the memory

module slot.

To protect a memory module after removal, place it in an electrostatic-safe container.

10. Insert a new memory module:

64 Chapter 11 Memory modules

CAUTION: To prevent damage to the memory module, hold the memory module by the edges

only. Do not touch the components on the memory module, and do not bend the memory module.

a. Align the notched edge (1) of the memory module with the tab in the memory module slot.

b. With the memory module at a 45-degree angle from the surface of the memory module

compartment, press the module (2) into the memory module slot until it is seated.

c. Gently press the memory module (3) down, applying pressure to both the left and right edges

of the memory module, until the retention clips snap into place.

CAUTION: To prevent damage to the memory module, be sure that you do not bend the

memory module.

11. Align the tabs on the memory module compartment cover with the notches on the computer, and

then close the cover (1).

12. Tighten the 2 cover screws (2).

13. Replace the battery.

65

14. Turn the computer right-side up, and then reconnect external power and external devices.

15. Turn on the computer.

66 Chapter 11 Memory modules

12 Updating software

Updated versions of the software provided with your computer may be available on the HP Web site.

Most software and BIOS updates on the HP Web site are packaged in compressed files called
SoftPaqs.

Some download packages contain a file named Readme.txt, which contains information regarding
installing and troubleshooting the file.

To update the software, follow these steps, which are explained in the remainder of this guide:

1. Identify your computer model, product category, and series or family. Prepare for a system BIOS

update by identifying the BIOS version currently installed on the computer.

If your computer is connected to a network, consult the network administrator before installing any
software updates, especially system BIOS updates.

NOTE: The computer system BIOS is stored on the system ROM. The BIOS initializes the

operating system, determines how the computer will interact with the hardware devices, and
provides for data transfer among hardware devices, including the time and date.

2. Access the updates on the HP Web site at http://www.hp.com.

3. Install the updates.

67

Updating the BIOS

To update the BIOS, first determine what BIOS version you currently have and then download and install
the new BIOS.

Determining the BIOS version

To determine whether available BIOS updates contain later BIOS versions than those currently installed
on the computer, you need to know the version of the system BIOS currently installed.

BIOS version information (also known as ROM date and System BIOS) can be displayed by opening
Setup Utility.

To display the BIOS information:

1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10

= BIOS Setup Options” message is displayed in the lower-left corner of the screen.

2. If Setup Utility does not open with the system information displayed, use the arrow keys to select

the Main menu.

When the Main menu is selected, BIOS and other system information is displayed.

3. To exit Setup Utility, use the arrow keys to select Exit > Exit Discarding Changes, and then press

enter.

Downloading a BIOS update

CAUTION: To prevent damage to the computer or an unsuccessful installation, download and install

a BIOS update only when the computer is connected to reliable external power using the AC adapter.
Do not download or install a BIOS update while the computer is running on battery power, docked in an
optional docking device, or connected to an optional power source. During the download and installation,
follow these instructions:

Do not disconnect power from the computer by unplugging the power cord from the AC outlet.

Do not shut down the computer or initiate Standby or Hibernation.

Do not insert, remove, connect, or disconnect any device, cable, or cord.

To download a BIOS update:

1. Access the page on the HP Web site that provides software for your computer:

Select Start > Help and Support, and then select the software and drivers update.

2. Follow the instructions on the screen to identify your computer and access the BIOS update you

want to download.

3. At the download area, follow these steps:

a. Identify the BIOS update that is later than the BIOS version currently installed on your

computer. Make a note of the date, name, or other identifier. You may need this information
to locate the update later, after it has been downloaded to your hard drive.

b. Follow the instructions on the screen to download your selection to the hard drive.

68 Chapter 12 Updating software

Make a note of the path to the location on your hard drive where the BIOS update will be
downloaded. You will need to access this path when you are ready to install the update.

NOTE: If you connect your computer to a network, consult the network administrator before

installing any software updates, especially system BIOS updates.

BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the
download is complete. If no instructions are displayed, follow these steps:

1. Open Windows Explorer by selecting Start > My Computer.

2. Double-click your hard drive designation. The hard drive designation is typically Local Disk (C:).

3. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains the

update.

4. Double-click the file that has an .exe extension (for example, filename.exe).

The BIOS installation begins.

5. Complete the installation by following the instructions on the screen.

NOTE: After a message on the screen reports a successful installation, you can delete the downloaded

file from your hard drive.

Updating the BIOS 69

Updating programs and drivers

To download and install software other than a BIOS update, follow these steps:

1. Access the page on the HP Web site that provides software for your computer:

Select Start > Help and Support, and then select the software and drivers update.

2. Follow the instructions on the screen to find the software you want to update.

3. At the download area, select the software you want to download and follow the instructions on the

screen.

NOTE: Make a note of the path to the location on your hard drive where the software will be

downloaded. You will need to access this path when you are ready to install the software.

4. When the download is complete, open Windows Explorer by selecting Start > My Computer.

5. Double-click your hard drive designation. The hard drive designation is typically Local Disk (C:).

6. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains the

update.

7. Double-click the file that has an .exe extension (for example, filename.exe).

The installation begins.

8. Complete the installation by following the instructions on the screen.

NOTE: After a message on the screen reports a successful installation, you can delete the downloaded

file from your hard drive.

70 Chapter 12 Updating software

13 Changing Instant Web Settings

Disabling and Enabling Instant Web

Instant Web is enabled by default. To disable (or reenable) Instant Web:

1. Open the Setup Utility by turning on or restarting the computer.

2. Immediately press f10 continuously to start Setup Utility.

3. Use the right arrow key to tab across the menu headings and select System Configuration.

4. Use the down arrow key to select IOS Support. Press enter.

5. Use the arrow key to select Disable or Enable. Press enter to make your selection.

6. Press f10 to save your changes.

7. Select Yes to confirm. The system will restart.

Disabling and Enabling Instant Web 71

14 Setup Utility

Starting Setup Utility

Setup Utility is a ROM-based information and customization utility that can be used even when your
Windows operating system is not working.

The utility reports information about the computer and provides settings for startup, security, and other
preferences.

To start Setup Utility:

Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10

▲

= BIOS Setup Options” message is displayed in the lower-left corner of the screen.

Using Setup Utility

Changing the language of Setup Utility

The following procedure explains how to change the language of Setup Utility. If Setup Utility is not
already running, begin at step 1. If Setup Utility is already running, begin at step 2.

1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10

= BIOS Setup Options” message is displayed in the lower-left corner of the screen.

2. Use the arrow keys to select System Configuration > Language, and then press enter.

3. Use the arrow keys to select a language, and then press enter.

4. When a confirmation prompt with your language selected is displayed, press enter.

5. To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving

Changes, and then press enter.

Your change goes into effect immediately.

Navigating and selecting in Setup Utility

Because Setup Utility is not Windows based, it does not support the TouchPad. Navigation and selection
are by keystroke.

To choose a menu or a menu item, use the arrow keys.

●

To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the

●

arrow keys or f5 or f6.

72 Chapter 14 Setup Utility

To select an item, press enter.

●

To close a text box or return to the menu display, press esc.

●

To display additional navigation and selection information while Setup Utility is open, press f1.

●

Displaying system information

The following procedure explains how to display system information in Setup Utility. If Setup Utility is
not open, begin at step 1. If Setup Utility is open, begin at step 2.

1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10

= BIOS Setup Options” message is displayed in the lower-left corner of the screen.

2. Select the Main menu. System information such as the system time and date, and identification

information about the computer is displayed.

3. To exit Setup Utility without changing any settings, use the arrow keys to select Exit > Exit

Discarding Changes, and then press enter.

Restoring default settings in Setup Utility

The following procedure explains how to restore the Setup Utility default settings. If Setup Utility is not
already running, begin at step 1. If Setup Utility is already running, begin at step 2.

1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10

= BIOS Setup Options” message is displayed in the lower-left corner of the screen.

2. Use the arrow keys to select Exit > Load Setup Defaults, and then press enter.

3. When the Setup Confirmation is displayed, press enter.

4. To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving

Changes, and then press enter.

The Setup Utility default settings go into effect when the computer restarts.

NOTE: Your password, security, and language settings are not changed when you restore the factory

default settings.

Exiting Setup Utility

You can exit Setup Utility with or without saving changes.

To exit Setup Utility and save your changes from the current session:

●

If Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow
keys to select Exit > Exit Saving Changes, and then press enter.

To exit Setup Utility without saving your changes from the current session:

●

If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the
arrow keys to select Exit > Exit Discarding Changes, and then press enter.

After either choice, the computer restarts in Windows.

Using Setup Utility 73

Setup Utility menus

The menu tables in this section provide an overview of Setup Utility options.

NOTE: Some of the Setup Utility menu items listed in this chapter may not be supported by your

computer.

Main menu

Select To do this

System information

Security menu

Select To do this

Administrator password Enter, change, or delete an administrator password.

Power-On Password Enter, change, or delete a power-on password.

System Configuration menu

Select To do this

Language Support Change the Setup Utility language.

Processor C4 State Enable/disable the processor C4 sleep state.

Boot Options Set the following boot options:

View and change the system time and date.

●

View identification information about the computer.

●

View specification information about the processor, memory size,

●

and system BIOS.

74 Chapter 14 Setup Utility

f10 and f12 Delay (sec.)―Set the delay for the f10 and f12 functions

●

of Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20).

IOS Support―Enable/disable the IOS Boot Menu during Setup

●

Utility. Set the delay for the user to start Setup Utility in 5 or 10
second intervals.

Internal Network Adapter boot―Enable/disable boot from Internal

●

Network Adapter.

Boot Device Priority―Set the boot device priority for:

●

Internal hard drive (select models only)

◦

USB Floppy

◦

USB CD/DVD ROM Drive

◦

USB flash drive

◦

USB Hard drive

◦

Select To do this

Diagnostics menu

Select To do this

Hard Disk Self Test (select models only) Run a comprehensive self-test on the hard drive.

Memory Test Run a diagnostic test on the system memory.

USB Card Reader

◦

Network adapter

◦

NOTE: Only the devices attached to the system will appear

in the boot order menu.

Setup Utility menus 75

Index

A

AC adapter

connecting 16
identifying 11

administrator password

creating 47
entering 47

managing 47
airport security devices 61
antennas 10
applications key, Windows 5
audio devices, connecting

external 41
audio functions, checking 41
audio-in (microphone) jack 8, 38
audio-out (headphone) jack 8,

38

B

battery

calibrating 21
charging 18, 21
conserving power 23
discharging 19
disposing 24
identifying 11
inserting 17
low battery levels 19
recharging 23
removing 17

storing 23
battery bay, identifying 9
battery light 6, 18, 19
battery power 16
battery release latches 9, 17
battery temperature 23
bay, battery 9
BIOS, updating 68
boot options 74
boot order 74

button, volume mute 39
buttons

left TouchPad 3
right TouchPad 4

C

cables

LAN 26
USB 54

VGA 43
calibrating battery 21
caps lock light, identifying 4
CD drive 61
changing Setup Utility

language 72
charging batteries 18, 21
checking audio functions 41
compartments, memory

module 10
components

additional hardware 11
bottom 9
display 8
front 5
left-side 7
right-side 7

TouchPad 3
connecting to a WLAN 31
connection, external power 16
conservation, power 23
cord, power 11
corporate WLAN connection 31
critical battery level 20

D

Diagnostics menu 75
digital card

inserting 52

removing 53

stopping 53

Digital Media Slot, identifying 7
diskette drive 61
display

image, switching 58

screen brightness hotkeys 58
display switch, identifying 9
displaying system information 73
drive light, identifying 6
drive media 13
drives

diskette 61

external 61

hard 61

optical 61
drives, boot order 74
DVD drive 61

E

earbuds 8, 38
encryption 31
entering a power-on

password 48

entering an administrator

password 47
exiting Setup Utility 73
external audio devices,

connecting 41
external drive 61
external monitor port 43
external monitor port,

identifying 7

F

firewall 31
fn key 5, 56
function keys 5, 56

H

hard disk drive, external 61
hard drive self test 75

76 Index

hard drive, external 61
hardware, identifying 3
headphone (audio-out) jack 8,

38
headphones 8, 38
Hibernation

exiting 14
initiated during critical battery

level 20

initiating 14

hotkeys

decreasing screen

brightness 58
decreasing speaker sound 59
description 56
increasing screen

brightness 58
increasing speaker volume 59
initiating QuickLock 58
initiating Standby 57
muting speaker sound 59
switching screen image 58
using 57

HP Mobile Broadband Module 33
HP Mobile Broadband,

disabled 33

hubs 54

I

icons

network status 27
wireless 27

Instant Web 1
Instant-On Software (IOS) 1
internal display switch,

identifying 9

internal microphone,

identifying 9, 38

Internet connection setup 30

J

jacks

audio-in (microphone) 8, 38
audio-out (headphone) 8, 38
RJ-45 (network) 7

K

keyboard hotkeys, identifying 56
keys

fn 5
function 5

Windows applications 5
Windows logo 5

L

labels

Microsoft Certificate of

Authenticity 12
regulatory 12
service tag 11

language support 74
latches, battery release 9
left TouchPad button,

identifying 3

lights

battery 6
caps lock 4
drive 6
power 6
webcam 9
wireless 6

local area network (LAN)

cable required 26
connecting cable 26

low battery level 19

M

Main menu 74
managing a power-on

password 48

managing an administrator

password 47

memory module

inserting 64
removing 64

memory module compartment

cover

removing 64
replacing 65

memory module compartment,

identifying 10
memory test 75
microphone (audio-in) jack 8, 38
monitor, connecting 43
mouse, external

connecting 56
setting preferences 56

multimedia components,

identifying 37

multimedia software

installing 40

using 40
mute button 39
mute hotkey, identifying 38

N

navigating in Setup Utility 72
network cable

connecting 26

noise suppression circuitry 26
network jack, identifying 7
network status icon 27
noise suppression circuitry, network

cable 26

O

operating system 24
optical drive 61

P

passwords

administrator 47

power-on 47

set in Setup Utility 46

set in Windows 46
ports

external monitor 43

USB 7, 8, 54
power

connecting 16

conserving 23
power connector, identifying 8
power cord, identifying 11
power light, identifying 6
power switch, identifying 6
power-on password

creating 48

entering 48

managing 48
Processor C4 State 74
product name and number,

computer 11
programs, updating 70
projector, connecting 43
public WLAN connection 31

Q

QuickLock 46
QuickLock hotkey 58

Index 77

R

readable media 13
regulatory information

HP Mobile Broadband Module

serial number 12
regulatory label 12
wireless 12

release latches

battery 9, 18

restoring default settings 73
right TouchPad button,

identifying 4

RJ-45 (network) jack,

identifying 7

S

screen brightness hotkeys 58
screen image, switching 58
security cable slot, identifying 7
Security menu 74
security, cable slot 7
security, wireless 30
selecting in Setup Utility 72
serial number, computer 11
service tag 11
setup of WLAN 30
Setup Utility, passwords set in 46
setup, computer 3
shut down 24
SIM

inserting 33
removing 34

software

installing 40
multimedia 40
Windows Media Player 40

speakers, identifying 8, 38
Standby

exiting 13
initiating 13

Standby hotkey 57
storing battery 23
switches

power 6
wireless 6

System Configuration menu 74
system information 74

T

temperature 23

TouchPad

buttons 3
identifying 3
using 56

TouchPad scroll zone,

identifying 3
traveling with the computer 23
turning off the computer 24

U

unresponsive system 24
USB cable, connecting 54
USB devices

connecting 54
description 54
removing 55

stopping 55
USB hubs 54
USB ports, identifying 7, 8, 54

V

vents, identifying 8, 10
video transmission types 58
volume down hotkey,

identifying 38
volume mute button 39
volume up hotkey, identifying 38
volume, adjusting 39

W

webcam light, identifying 9, 38
webcam, identifying 9, 38
Windows applications key,

identifying 5
Windows logo key, identifying 5
Windows, passwords set in 46
wireless antennas 10
wireless controls

button 28

operating system 28
wireless icon 27
wireless light, identifying 6, 28
wireless network (WLAN)

connecting 31

corporate WLAN

connection 31
equipment needed 30
functional range 32
public WLAN connection 31
security 30

wireless network, connecting 27

wireless switch, identifying 6, 28
WLAN antennas, identifying 10
WLAN device 27
writable media 13
WWAN antennas, identifying 10

78 Index