HP M8501 ACL, M8502 ACL Installation And User Manual

M8501 and M8502 ACL
Tape Drive Installation
and User’s Guide

Abstract

This guide provides information about installing, operating, and maintaining the M8501
and M8502 ACL tape drives on an HP Integrity NonStop™ NS-series server. This
guide is written for those who install or maintain the M8501 and M8502 ACL tape
drives.

Product Version

N.A.

Supported Release Version Updates (RVUs)

This guide supports H06.03 and all subsequent H-series RVUs until otherwise
indicated by its replacement publication.

Part Number Published

529972 -001 July 20 05

Document History

Part Number Product Version Published

529972- 001 N.A. July 2005

Hewlett-Packard Company—529972-001

i

M8501 and M8502 ACL
Tape Drive Installation
and User’s Guide

Glossary Index Examples Figures Tables

What’s New in This Manual v

Manual Information v
New and Changed Information v

About This Manual vii

Notation Conventions vii

1. Overview and Features

Overview 1-1
Models and Accessories 1-2
Internal Tape Drive 1-3
Magazine 1-4
Power Supply 1-4
Robotics 1-4
Front Panel Indicators 1-6

2. Setting Up the ACL Tape Drives

Setting up the M8501 ACL Rackmount Unit 2-1
Setting up the M8502 ACL Tabletop 2-5

3. Install ing and Config uri ng t he ACL Tape Drive for th e NonS t op
NS-Series Server

Overview 3-1
Installation 3-3
Configuration 3-7

4. Operation

Front Panel 4-1

Magazine Door 4-2
Indicators 4-2
Initialization Screen 4-3
ACL Default Screen 4-4

Display Screens and Options 4-4

Contents

M8501 and M8502 ACL Tape Drive Installation and User’s Guide—529972-001

ii

5. Maintenance

Technical Support Information Option 4-5
Access Magazine Option 4-6
Move Media 4-6
LCD Contrast Controls 4-8
Power 4-8
Status 4-9
Online 4-9

Menu Selections 4-10

View System Data 4-10

Inserting and Removing Tape Cartridges 4-13

Removing the Magazine 4-13
Inserting Cartridges into the Magazine 4-13
Barcode Labels 4-14

5. Maintenance

Introduction 5-1
Running a Cleaning Cartridge 5-1

Automatically Running a Cleaning Cartridge 5-1
Manually Running a Cleaning Cartridge 5-2

Replacing a Cleaning Cartridge in a Reserved Slot 5-3

Replacing a Cleaning Cartridge in the Right Magazine 5-3

6. Troubleshooting

Platform Problems 6-1
Error Recovery 6-1
Error Recovery Procedures 6-3
Fault Symptom Codes (FSCs) 6-3

Safety and Compliance
Index

Examples
Figures

Figure 1-1. Hardware Configuration 1-2
Figure 1-2. Rear View of Tape Drive 1-3
Figure 1-3. Tape Cartridge Magazine 1-4
Figure 1-4. View of Barcode Reader and Shuttle Assembly 1-5
Figure 1-5. Front Panel Indicators 1-6
Figure 2-1. M8501 ACL Template 2-1

Contents

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

iii

Tables

Figure 2-2. Installing the Slide Members 2-3
Figure 2-3. Installing Slide Member Fasteners 2-4
Figure 2-4. Tabletop Model Clearances 2-5
Figure 3-1. Hardware Configuration 3-2
Figure 3-2. Tape Drive’s Fibre Channel Port Connection 3-3
Figure 3-3. LC-LC Fiber Cable 3-4
Figure 3-4. View of Two FCSAs at the Rear of the Server 3-5
Figure 3-5. Powering On the ACL Tape Drive 3-6
Figure 3-6. Status Button 3-7
Figure 3-7. Drive 1 LTO Loaded Button 3-8
Figure 3-8. Drive Identification Button 3-9
Figure 3-9. Viewing the Portname 3-10
Figure 4-1. Front Panel 4-1
Figure 4-2. Magazine Door Mechanical Release 4-2
Figure 4-3. Initialization Screen 4-3
Figure 4-4. ACL Default Screen 4-4
Figure 4-5. Technical Support Information 4-5
Figure 4-6. Access Magazine Screen 4-6
Figure 4-7. Move Media Screen 4-6
Figure 4-8. Move Media Screen (Source) 4-7
Figure 4-9. Move Media Screen (Destination) 4-7
Figure 4-10. Power Down Initiation Screen 4-8
Figure 4-11. Status Screen 4-9
Figure 4-12. Menu Screen 4-10
Figure 4-13. View ACL Options Screen (Initial Screen) 4-11
Figure 4-14. Tape Magazine With Tape Cartridges Installed 4-14
Figure 4-15. Barcode Label Installation (LTO) 4-15
Figure 6-1.

Troubleshooting Flow Chart 6-2

Tables

Table 1-1. Models and Slot Capacities 1-2
Table 3-1. Fiber Cables 3-3
Table 4-1. ACL Front Panel Indicators 4-2
Table 4-2. View ACL Options 4-11
Table 6-1. Error Recovery Procedures 6-3
Table 6-2. Fault Symptom Code s 6-3

Contents

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

iv

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

v

What’s New in This Manual

Manua l In forma t i o n

M8501 and M8502 ACL
TapeDrive Installation
and User’s Guide

Abstract

This guide provides information about installing, operating, and maintaining the M8501
and M8502 ACL tape drives on an HP Integrity NonStop™ NS-series server. This
guide is written for those who install or maintain the M8501 and M8502 ACL tape
drives.

Product Version

N.A.

Supported Release Version Updates (RVUs)

This guide supports H06.03 and all subsequent H-series RVUs until otherwise
indicated by its replacement publication.

Document History

New and Changed Information

This is a new manual.

Part Numb er Pu b l i sh ed

529972- 001 J uly 2005

Part Number Product Version Published

529972- 001 N.A. July 2005

What’s New in This Manual

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

vi

New and Changed Information

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

vii

About This Manual

Notation Conventions

Hypertext Links

Blue underline is used to indicate a hypertext link within text. By clicking a passage of
text with a blue underline, you are taken to the location described. For example:

This requirement is described under Backup DAM Volumes and Physical Disk

Drives on page 3-2.

General Sy ntax Notation

This list summarizes the notation conventions for syntax presentation in this manual.

UPPERCASE LETTERS. Uppercase letters indicate keywords and reserved words. Type

these items exactly as shown. Items not enclosed in brackets are required. For
example:

MAXATTACH

lowercase italic letters. Lowercase italic letters indicate variable items that you supply.

Items not enclosed in brackets are required. For example:

file-name

computer type. Computer type letters within text indicate C and Open System Services

(OSS) keywords and reserved words. Type these items exactly as shown. Items not
enclosed in brackets are required. For example:

myfile.c

italic computer type. Italic computer type letters within text indicate C and Open

System Services (OSS) variable items that you supply. Items not enclosed in brackets
are required. For example:

pathname

[ ] Brackets. Brackets enclose optional syntax items. For example:

TERM [\system-name.]$terminal-name
INT[ERRUPTS]

A group of items enclosed in brackets is a list from which you can choose one item or
none. The items in the list can be arranged either vertically, with aligned brackets on

About This Manual

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

viii

General Syntax Notation

each side of the list, or horizontally, enclosed in a pair of brackets and separated by
vertical lines. For example:

FC [ num ]
[ -num ]
[ text ]

K [ X | D ] address

{ } Braces. A group of items enclosed in braces is a list from which you are required to

choose one item. The items in the list can be arranged either vertically, with aligned
braces on each side of the list, or horizontally, enclosed in a pair of braces and
separated by vertical lines. For example:

LISTOPENS PROCESS { $appl-mgr-name }
{ $process-name }

ALLOWSU { ON | OFF }

| Ve rtical Line. A vertical line separates alternatives in a horizontal list that is enclosed in

brackets or braces. For example:

INSPECT { OFF | ON | SAVEABEND }

… Ellipsis. An ellipsis immediately following a pair of brackets or braces indicates that you

can repeat the enclosed sequence of syntax items any number of times. For example:

M address [ , new-value ]…
[ - ] {0|1|2|3|4|5|6|7|8|9}…

An ellipsis imme diately fol lowing a single syntax item indi cates that you can repeat that
syntax item any number of times. For example:

"s-char…"

Punctuation. Parentheses, commas, semicolons, and other symbols not previously

described must be typed as shown. For example:

error := NEXTFILENAME ( file-name ) ;
LISTOPENS SU $process-name.#su-name

Quotation marks around a symbol such as a bracket or brace indicate the symbol is a
required character that you must type as shown. For example:

"[" repetition-constant-list "]"

Item Spacing. Spaces shown between items are required unless one of the items is a

punctuation symbol such as a parenthesis or a comma. For example:

CALL STEPMOM ( process-id ) ;

If there is no space between two items, spaces are not permitted. In this example, no
spaces are permitted between the period and any other items:

$process-name.#su-name

About This Manual

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

ix

Notation for Messages

Line Spacing. If the syntax of a command is too long to fit on a single line, each

continuation line is indented three spaces and is separated from the preceding line by
a blank line. This spacing distinguishes items in a continuation line from items in a
vertical list of selections. For example:

ALTER [ / OUT file-spec / ] LINE
[ , attribute-spec ]…

!i and !o. In procedure calls, the !i not ation follows an input par ame ter (o ne that passes data

to the called procedure); the !o notation follows an output parameter (one that returns
data to the calling program). For example:

CALL CHECKRESIZESEGMENT ( segment-id !i
, error ) ; !o

!i,o. In procedure calls, the !i,o notation follows an input/output parameter (one that both

passes data to the called procedure and returns data to the calling program). For
example:

error := COMPRESSEDIT ( filenum ) ; !i,o

!i:i. In procedure calls, the !i:i notation follows an input string parameter that has a

corresponding parameter specifying the length of the string in bytes. For example:

error := FILENAME_COMPARE_ ( filename1:length !i:i
, filename2:length ) ; !i:i

!o:i. In procedure calls, the !o:i notation follows an output buffer parameter that has a

corresponding input parameter specifying the maximum length of the output buffer in
bytes. For example:

error := FILE_GETINFO_ ( filenum !i
, [ filename:maxlen ] ) ; !o:i

Notation for Messages

This list summarizes the notation conventions for the presentation of displayed
messages in this manual.

Bold Text. Bold text in an example indicates user input typed at the terminal. For example:

ENTER RUN CODE
?123
CODE RECEIVED: 123.00

The user must press the Return key after typing the input.

Nonitalic text. Nonitalic letters, numbers, and punctuation indicate text that is displayed or

returned exactly as shown. For example:

Backup Up.

About This Manual

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

x

Notation for Management Programming Interfaces

lowercase italic letters. Lowercase italic letters indicate variable items whose values are

displayed or returned. For example:

p-register
process-name

[ ] Brackets. Brackets enclose items that are sometimes, but not always, displayed. For

example:

Event number = number [ Subject = first-subject-value ]

A group of items enclosed in brackets is a list of all possible items that can be
displayed, of which one or none might actually be displayed. The items in the list can
be arranged either vertically, with aligned brackets on each side of the list, or
horizontally, enclosed in a pair of brackets and separated by vertical lines. For
example:

proc-name trapped [ in SQL | in SQL file system ]

{ } Braces. A group of items enclosed in braces is a list of all possible items that can be

displayed, of which one is actually displayed. The items in the list can be arranged
either vertically, with aligned braces on each side of the list, or horizontally, enclosed in
a pair of braces and separated by vertical lines. For example:

obj-type obj-name state changed to state, caused by
{ Object | Operator | Service }

process-name State changed from old-objstate to objstate
{ Operator Request. }
{ Unknown. }

| Ve rtical Line. A vertical line separates alternatives in a horizontal list that is enclosed in

brackets or braces. For example:

Transfer status: { OK | Failed }

% Percent Sign. A percent sign precedes a number that is not in decimal notation. The

% notation precedes an octal number. T he %B notation precedes a binary number.
The %H notation precedes a hexadecimal number. For example:

%005400
%B101111
%H2F
P=%p-register E=%e-register

Notation for Management Programming Interfaces

This list summarizes the notation conventions used in the bo xed descriptions of
programmatic commands, event messages, and error lists in this manual.

About This Manual

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

xi

Change Bar Notation

UPPERCASE LETTERS. Uppercase letters indicate names from definition files. T ype these

names exactly as shown. For example:

ZCOM-TKN-SUBJ-SERV

lowercase letters. Words in lowercase letters are words that ar e part of the notation,

including Data Definition Language (DDL) keywords. For example:

token-type

!r. The !r notation following a token or field name indicates that the token or field is

required. For example:

ZCOM-TKN-OBJNAME token-type ZSPI-TYP-STRING. !r

!o. The !o notation following a token or field name indicates that the token or field is

optional. For example:

ZSPI-TKN-MANAGER token-type ZSPI-TYP-FNAME32. !o

Change Bar Notation

Change bars are used to indicate substantive differences between this manual and its
preceding version. Change bars are vertical rules placed in the right margin of
changed portions of text, figures, tables, examples, and so on. Change bars highlight
new or revised information. For example:

The message types specified in the REPORT clause are different in the COBOL
environment and the Common Run-Time Environment (CRE).

The CRE has many new message types and some new message type codes for
old message types. In the CRE, the message type SYSTEM includes all
messages except LOGICAL-CLOSE and LOGICAL-OPEN.

About This Manual

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

xii

Change Bar Notation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

1-1

1 Overview and Features

This section includes:

Overview

The M8501 and M8502 auto cartridge loader (ACL) tape drives support the LTO
Ultrium Gen 3 tape drive. They are designed for backup operations for the NonStop
NS-series server. The M8501 comes in a rackmount configuration, and the M8502
comes in a tabletop configuration.

These auto cartridge loader tape drives connect to the Fibre Channel ServerNet
adapter (FCSA) on the NonStop NS-series server by a fiber optic cable. Figure 1-1
shows how the ACL tape drives connect to the server.

Overview 1-1
Models and Accessories 1-2
Internal Tape Drive 1-3
Magazine 1-4
Power Supply 1-4
Robotics 1-4
Front Panel Indicators 1-6

Overview and Features

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

1-2

Models and Accessories

Models and Accessories

These auto cartridge loader tape drives are configured with one internal LTO Gen 3
tape drive along with one removable tape cartridge magazine.

Figure 1-1. Hardware Configuration

Table 1-1. Models and Slot Capacities

Model Drives Slots LTO

M8501 1 15 LTO 12.0 TB
M8502 1 15 LTO 12.0 TB

ACL Tape

Fiber
Cable

FCSA

NonStop
NS-Series
Server

Drive

Overview and Features

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

1-3

Internal Tape Drive

Internal Tape Drive

The ACL units supports a single internal tape drive. The internal tape drive can be hot­swapped.

Figure 1-2. Rear View of T ape Drive

Single Drive

Overview and Features

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

1-4

Magazine

Magazine

The ACL units contains one removable tape cartridge magazine that is accessible
through the front left door. The door is opened by using the GUI touch screen on the
control panel.

Power Supply

Power to the ACL units are supplied through an AC connector at the rear panel of the
power supply. T he ACL unit’s power is normally controlled from the graphical user
interface (GUI) touch screen; however, a manual power disconnect switch, located at
the rear of the power supply may also be used.

Robotics

The ACL tape drive’s robotics consist of a cartridge shuttle, motor hardware, motor
drives, and other support electronics. These robotics are capable of picking and
placing tapes throughout the tape drive and the tape cartridge magazine.

The cartridge shuttle assembly includes a mounted barcode reader for scanning tape
cartridges installed in the magazine and tape drive.

Figure 1-3. Tape Car tridge M agazine

Note. Both a full barcode reader scan and a physical scan are conducted each time the unit is

initially powered up, or each time a tape maga z ine is exchanged .

Overview and Features

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

1-5

Robotics

Figure 1-4. View of Barcode Reader and Shuttle Assembly

Barcode Reader Shuttle

Overview and Features

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

1-6

Front Panel Indicators

Front Panel Indicators

The ACL tape drive’s front panel indicators consist of:

•

Viewing window - lets you visually check the unit’s internal operations

•

GUI touch screen - manually operated to setup and configure the unit

•

ACL module status LED - displays the unit’s operational status

Figure 1-5. Front Panel Indicators

ACL Status LED GUI Touch Screen Internal Viewing
Window

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

2-1

2 Setting Up the ACL Tape Drives

This section includes:

Setting up the M8501 ACL Rackmount Unit

Setting up the ACL rackmount unit requires a template and storage cabinet slide rails
to install the unit in a storage cabinet.

To setup the rackmount model:

1. Ensure that you have adequate space available in the rack.

2. Use the template that is shipped with the unit to mark the location of the mounting

hardware on the mounting rails of the storage cabinet.

Setting up the M8501 ACL Rackmount
Unit

2-1

Setting up the M8502 ACL Tabletop 2-5

Figure 2-1. M8501 ACL Template

Setting Up the ACL Tape Drives

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

2-2

Setting up the M8501 ACL Rackmount Unit

a. Push back the tabs in the top of the template and place them in the correct

holes in the mounting rack. Match up the hole pattern indicated on the sides of
the template with the hole pattern in the mounting rack.

b. Make sure to begin measuring in the correct place. If a unit is already installed

immediately below the planned position of the new unit, then place the
template against the front of the mounting rack and rest it on top of the
previously installed unit.

c. Use the front of the template to mark the attachment points for mounting

brackets, rails, components, or cage nuts on the back of the storage cabinet.

d. Use the back of the template to mark the attachment points for the mounting

brackets, rails, components, or cage nuts on the back of the storage cabinet.

3. Remove the template.

4. Install the slide members for the rackmount unit.

5. If the slide members are already installed, attach the front and rear mounting

brackets to the outer and middle slide members.

Setting Up the ACL Tape Drives

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

2-3

Setting up the M8501 ACL Rackmount Unit

6. Attach the slide members using the supplied fasteners. Install the clip nuts on the

inside of the slide member’s front and back mounting bracket only if the vertical rail
mounting holes are not tapped.

Figure 2-2. Installing the Slide Members

Setting Up the ACL Tape Drives

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

2-4

Setting up the M8501 ACL Rackmount Unit

7. Push the middle slide member as far as possible to the front of the slide member

assembly.

8. Install the two clip nuts on each of the rack’s front vertical rails.

9. Confirm that the bearing carrier is in the retained position.

10. Lift the unit and visually align the inner and middle slide members.

11. Verify the ball bearing slide members are located in the front position.

12. Slide the unit completely into the rack until the front panel touches the rack.

13. Remove and discard the tape that holds the door in the latched position, leaving

the door open.

Figure 2-3. Installing Slide Member Fasteners

Caution. It is recommended that the unit be lifte d by two people. Do not a ttempt to lift the unit

by yo urself.

Setting Up the ACL Tape Drives

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

2-5

Setting up the M8502 ACL Tabletop

14. Attach the unit to the rack using two 10-32 captive thumbscrews that are located

on the lower left and right front panel.

15. Fully tighten the rear-mounting bracket screws.

Setting up the M8502 ACL Tabletop

The M8502 ACL tabletop requires no mechanical assembly for mounting (see

Figure 2-4). Place the unit on a desk, table, or other stable horizontal surface. Ensure

that the cooling grills at the front and the fans at the rear of the unit are not obstructed.
Allow 12 inches (30.4 centimeters) of clearance at the front and 6 inches (15.2
centimeters) at the rear of the unit to allow for adequate cooling.

Figure 2-4. Tabletop Model Clearances

6 inches
(15.2

12 inches
(30.4
centi­meters)

centi­meters)

Setting Up the ACL Tape Drives

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

2-6

Setting up the M8502 ACL Tabletop

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

3-1

3

Installing and Configuring the ACL
Tape Drive for the NonStop NS­Series Server

This section includes:

Overview

A multimode sho rtwave fiber op ti c cable mu st be used to conne ct the A CL t ape d riv e to
the Fibre Channel ServerNet adapter (FCSA) on the HP NonStop NS-series server.

Figure 3-1 shows how the ACL tape drive connects to the server.

Overview 3-1
Installation 3-3
Configuration 3-7

Installing and Configuring the ACL Tape Drive for the
NonStop NS-Series Server

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

3-2

Overview

Figure 3-1. Hardware Configuration

Tape Drive

Fiber
Cable

FCSA

NonStop
NS-Series
Server

Installing and Configuring the ACL Tape Drive for the
NonStop NS-Series Server

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

3-3

Installation

Installation

1. Connect one end of the fiber cable to the top Fibre Channel port at the rear of the

tape drive. See Figure 3-2 for the location.

2. Connect the other end of the fiber cable to the Fibre Channel ServerNet adapter

(FCSA) on the NonStop NS-series server. See Figure 3-4

on page 3-5 for the

location.
A LC-LC fiber optic cable must be used to connect the ACL tape drive to the

FCSA. Figure 3-3

on page 3-4 shows each side of the cable.

Figure 3-2. Tape Drive’s Fibre Channel Port Connection

Table 3-1. Fiber Cables

Connector Fiber Cable Fiber Cable Distance

LC - LC 50/125 µm 2-300 meters (6.56-984.25 feet)
LC - LC 62.5/125 µm 3-150 meters (9.8 4-4 92.13 feet)

Fiber Cable

Installing and Configuring the ACL Tape Drive for the
NonStop NS-Series Server

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

3-4

Installation

Figure 3-3. LC-LC Fiber Cable

Installing and Configuring the ACL Tape Drive for the
NonStop NS-Series Server

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

3-5

Installation

3. Attach the power cord to the ACL tape drive’s AC power receptacle (see

Figure 3-5) and then plug the other end into an AC power outlet.

4. Toggle the power switch to the on position from the rear of the unit.

5. Press anywhere on the GUI touch screen to activate the display, and then turn the

unit on.

Figure 3-4. View of Two FCSAs at the Rear of the Server

Note. The tape drive does not have protection against lightning surges. Customers in high-risk

areas sho uld use exte rnal surge protection rated for use in th eir location and be able t o handle
the powe r demand of th e tap e drive.

Installing and Configuring the ACL Tape Drive for the
NonStop NS-Series Server

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

3-6

Installation

Figure 3-5. Powering On the ACL Tape Drive

GUI Touch Screen

Power Cord Toggle Switch

Installing and Configuring the ACL Tape Drive for the
NonStop NS-Series Server

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

3-7

Configuration

Configuration

Follow steps 1-4 to navigate through the ACL tape drive’s menu configuration to view
the PORTNAME of the tape drive.

The purpose of viewing the tape drive’s PORTNAME is because it will be added to the
SCF configuration in step 5 on page 3-10.

1. Press the Status button on the GUI touch screen.

Figure 3-6. Status Button

Status Button

Installing and Configuring the ACL Tape Drive for the
NonStop NS-Series Server

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

3-8

Configuration

2. Press the Drive 1 LTO Loaded button.

Figure 3-7. Drive 1 LTO Loaded Button

Drive 1 LTO Loaded Button

Installing and Configuring the ACL Tape Drive for the
NonStop NS-Series Server

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

3-9

Configuration

3. Press the Drive Identification button.

Figure 3-8. Drive Identification Button

Drive Identification Button

Installing and Configuring the ACL Tape Drive for the
NonStop NS-Series Server

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

3-10

Configuration

4. View the World Wide Port 0 Name number. This number will be used as the

PORTNAME in step 5.

5. In SCF, issue this command:

SCF> ADD TAPE $tape, SENDTO STORAGE, LOCATION (group, module,
slot), SAC sac-id, PORTNAME 64-bit-portname, LUN lun-id

Example:

SCF> ADD TAPE $TAPE1, SENDTO STORAGE, LOCATION (110,2,3), SAC
1, PORTNAME 50060B00002E0934, LUN 1

6. To start the ACL tape drive on the server, issue this command in SCF:

SCF> START TAPE $tape

Example:

SCF> START TAPE $TAPE1

For complete details about the ADD and START commands, including command
syntax, see the SCF Reference Manual for the Storage Subsystem.

Figure 3-9. Viewing the Portname

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-1

4 Operation

This section includes:

Front Panel

The front panel of the ACL units include the left magazine door, a Graphical User
Interface (GUI) touch screen, an ACL status LED, and a viewing window (see

Figure 4-1).

Front Panel 4-1
Display Screens and Options 4-4
Menu Selections 4-10
Inserting and Removing Tape Cartridges 4-13

Figure 4-1. Front Panel

Left Magazine Viewing
Door Window GUI Touch Screen

ACL Status
LED

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-2

Magazine Door

Magazine D oor

The magazine door has both an electrical release (via the GUI touch screen) and a
manual release. It is always recommended that you open the magazine door using the
GUI touch screen. If the GUI touch screen should fail, you can manually open the door
by pushing a paper clip into the mechanical release at the center of the door.

Indicators

The ACL tape drive’s front panel indicators consist of a GUI touch screen and an ACL
status LED.

Figure 4-2. Magazine Door Mechanical Release

Table 4-1. ACL Front Panel Indicators

Indicator Description

Solid Gre en The AC L is operating correctly un der normal con ditions.
Flas hing Green The ACL is operating corr ectly; however, a chang e is

being made via the GUI touch screen that interrupts the
current ACL operation.

Solid Amber The ACL is in a fault state as indicated by the fault

message on the GUI touch screen.

Magazine Door Release ACL Status LED

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-3

Initialization Screen

Initia l izatio n Scree n

When power is first applied to the ACL tape drives, a series of power-on self test
(POST) diagnostics are performed. After the POST completes, the following
initialization screen appears:

Figure 4-3. Initialization Screen

Note. Pressing Continue will display the ACL default scre en.

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-4

ACL Default Screen

ACL Default Screen

After the POST executes successfully and the ACL initialization completes, the ACL
tape drive Default Screen appears as shown in Figure 4-4.

The ACL Default screen enables you to select these options:

•

Technical Support Inform ation (HP Logo)

•

Magazine Access

•

Move Media

•

LCD Contrast Controls

•

Power

•

Status Online

•

Menu

Display Screens and Options

The ACL GUI touch screen displays graphics and text in the form of easy to
understand messages. Graphics and text messages, along with their functions, are
described in this section.

Figure 4-4. ACL Default Screen

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-5

Technical Support Information Option

Technical Support Information Option

Selecting the HP logo in the top left corner will display HP specific technical support
assistance information. See Figure4-5.

Figure 4-5. Technical Support Information

Note. The HP Global Support C enter (GCSC) provides te c hnical support for this product.

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-6

Access Magazine Option

Access Magazine Option

Selecting this option lets you display the Access Magazine screen (see Figure 4-6).
The Access Magazine option lets you ga in access to the left magazine door for tape
cartridge placement or removal.

Move Media

Selecting this option lets you display the Move Media screen, see Figure 4-7. The
Move Media option lets you remove a cartridge from the tape drive, load a cartridge to
the tape drive, or to move cartridges within the ACL.

Figure 4-6. Access Magazine Screen

Figure 4-7. Move Media Screen

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-7

Move Media

These figures illustrate moving a cartridge from the tape drive to a slot in the
magazine:

1. Touch the Source input box or Source Element Type from the Move Media Screen.

The Source input box will change from gray to an active state, see Figure 4-8.

2. Touch the source you want to move, from the Source Element Type selections.

The options available are Drive and Slot.

3. Touch the Destination Input Box on the Move Media Screen. The Destination Input

Box will change from gray to an active state. See Figure 4-9.

Figure 4-8. Move Media Screen (Source)

Figure 4-9. Move Media Screen (Destination)

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-8

LCD Contrast Controls

4. Touch the destination option that you want to move media to. From the Destination

Element Type selections. The options available are Drive and Slot. Repeat
selecting the desired destination option until the desired option is displayed in the
Destination Input Box, for example, touching Slot three times displays Slot 3 in the
Destination Input Box.

5. Touch the “Execute Move” button. The ACL robotics move the cartridge from the

Drive to Slot 3.

LCD Contrast Controls

Selecting these options let you increase or decrease the contrast of the LCD display.
Incremental steps are set by adjusting the LCD contrast controls (up and down arrows)
from the upper right corner of the ACL Default Screen. Incremental steps can range
from 0 to 31 depending on your preference.

Power

Selecting this option initiates an ACL power-down operation.

Note. The ACL moves the s huttle assembly to the parked positio n before powering down.

Figure 4-10. Power Down Initiation Screen

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-9

Status

Status

Selecting this option lets you display the ACL Status screen. You can identify a tape
drive type, view physical tape drive status, tape drive cleaning information, and tape
cartridge information by opening the corresponding areas on the screen.

Online

Selecting this option from the ACL Default Screen lets you place the ACL online or
offline.

Figure 4-11. Status Screen

Note. By default the ACL automatic ally come s o nlin e af ter a power-up initializati on.

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-10

Menu Selections

Menu Selections

Selecting Menu on the ACL Default Screen lets you view, configure, and use the ACL.
The Menu option displays three distinct areas:

•

View System Data

•

Utilities

•

Edit Options

View System Data

The View System Data area lets you select these screens:

•

ACL Options

•

SCSI Options

•

Network Options

•

ACL Info

•

Cartridge Map

ACL Options

Selecting this option lets you view but not modify the ACL settings as defined in the
ACL option of the Edit Options area. Table 4-2

on page 4-11 describe the available

options.

Figure 4-12. Menu Screen

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-11

View System Data

Table 4-2 below, lists and describes the available ACL options.

Note. You ca n view the next sequential ACL Optio ns s c reen by selecting the up arrow. To
return to the previou s ACL Op t ions screen se lec t th eir Back button to return to the Menu
screen.

Figure 4-13. View ACL Options Screen (Initial Screen)

Table 4-2. View ACL Options

Option Description

ACL Stays Offline After
Power-up Initialization

ACL does not go online after power-up init ialization. You
must select the Online option from the Menu screen on the
GUI touch screen. The default is Disabled.

Auto Pow er-up on
Installed Drive

Enables a tape drive to be automatically powered up (after a
delay), afte r replacing a tape drive.

Unload Mode Selects the unload mode for ACL tape drives. If Implicit, the

ACL unloads a tape driv e before atte m pt ing to move a
cartridge from that tape drive. If Explicit, th e server must
issue a SCSI UNLOAD command to a tape drive before
each MOVE MEDIUM command that removes a cartridge
from that tape drive. The default is Implicit.

Total Res erved Slots Lets you rem ov e from use a specified number of slo ts at th e

rear of the magazine . The default is 0.

Auto Clean Mode Lets you enable an automatic cleaning cycle. To use this

option, you must have reserved a slot for a cleaning
cartridge using th e Total Reserved Slots option. The default
is Disabled.

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-12

View System Data

Drive and Slot Num bering Lets you specify whether SCSI elements in the ACL

displays with either zero-based or one-based. This affects
the GUI tou c h s c reen, not the ac t ual SCSI elem ent
address es . Th e default is on e based.

ACL Mode Lets you set the robotics operating mode to Random or

Sequen tia l. T he default is Random.

Seque ntial Mode L ets you selec t a normal or r ec irculate frequency mode. The

default is Normal. (Only available if ACL Mode is set to
Sequential).

LCD Contrast Adjust The LCD contrast controls let you increase or decrease the

contrast of the LCD display. The increment steps are set by
adjusting the LCD Contrast Adjust option from the ACL
option. Inc remental steps c an range from 0 to 31 depe nding
on your preference.

Barcode Label Size Le ts yo u lim it the maxim um number of charac te rs of th e

barcode label. Possible settings are 1 through 8. The default
is 8.

Barcode Label Alignment Lets you spec ify t he alignme nt of a barcode label. The

options a re Left to Right. W hen used in co njunction w ith th e
label size option, this option strips unwanted trailing
characters (left alignment) or leading characters (right
alignment). The default is Left Align.

Barcode Label Che c k
Digit

Lets you specify whether to enable or disable the verificati on
of a check digit character in the barcode label. The default is
Disabled

Barcode R eader Lets you specify whet her the barco de reader wil l ret ry

reading b arc ode labels . Th e default is Ret ries Enabled.

Module Configuration Lets you specify the ACL Module Configuration. Three

options a re av ailable:

•

Standalone - Used when the AC L contains a sin gle
module

•

Master - Used to select the module in a multi-module
ACL

•

Slave - Used to select the other modules in a multi­module ACL

Table 4-2. View ACL Options

Option Description

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-13

Inserting and Removing Ta pe Cartridges

Inserting and Removing Tape Cartridges

The magazine must be removed from the ACL in order to remove or insert tape
cartridges. Make sure the slot you want to use is not already reserved for a tape
cartridge that is now in a tape drive. The safest way to do this is to unload all tape
drives before removing a magazine. You can unload the tape drive either through your
host system software or by using the “Move Media” option on the Default Screen.

Removing the Magazine

You must manually remove the ACL magazine. To access the magazine, use the
“Magazine Access” option on the Default Screen. This option lets you open the left
magazine door. After opening the maga zi ne door, pull the magazine out and aw ay fr om
the ACL chassis.

Inserting Cartridges into the Magazine

A full magazine is shown in Figure 4-14. Note that the lowest numbered tape cartridge
slot is the one closest to the front of the magazine.

Insert a tape cartridge so that the barcode labels are facing outward.

Note. Hand le and store ta pe car tr idges in a clean, dust- fr ee environment .

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-14

Barcode Labels

Barcode Labels

Figure 4-15 show you how to install a barcode label onto a tape cartridge.

LTO Cartridge Media

The following are tips to ensure maximum LTO cartridge media performance and life:

1. Place labels only in the recessed area, just above the write protection switch (See

Figure). Never place labels on the top, bottom sides or rear of the cartridge, they
can cause loader faults and interfere with normal operations. Such labels can
come off inside the equipment causing damage.

2. Always inspect cartridges for incorrect or improperly attached labels.

3. Never erase information on a cartridge label, always replace the label.

Figure 4-14. Tape Magazine With Tape Cartridges Installed

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-15

Barcode Labels

Note. Barcode labels may be placed on the media with the alpha-numeric characters on the
left or the right.

Figure 4-15. Barcode Label Installation (LTO)

Operation

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

4-16

Barcode Labels

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

5-1

5 Maintenance

This section includes:

Introduction

This section describes the Clean One Drive menu option contained in the Maintenance
submenu of the Utilities area on the front panel display. You can use the Clean One
Drive menu option to clean the LTO Gen 3 tape drive that is installed in the ACL.

Running a Cleaning Cartridge

Because the cleaning cartridge is abrasive, you should not use it unless the message
“Use Cleaner” appears on the front panel display. There are two ways to manage the
cleaning of the installed tape drives:

•

Automatically, by enabling Auto Clean Mode.

•

Manually, by selecting the Clean One Drive menu option from the Maintenance
submenu on the front panel display.

Automatically Runn ing a Cleaning Cartridge

You can configure the ACL tape drive so that it automatically runs the cleaning
cartridge mode. After a tape drive that needs cleaning completes an unload operation,
it sends a cleaning needed message to the unit. This activates an automatic cleaning
cycle if the cleaning cartridge slot has been reserved and Auto Clean Mode has been
selected from the ACL tape drive’s Options menu.

To automatically run a cleaning cartridge using Auto Clean Mode:

1. Reserve a cleaning cartridge slot.

2. Enable Auto Clean Mode.

Introduction 5-1
Running a Cleaning Cartridge 5-1
Replacing a Cleaning Cartridge in a Reserved Slot 5-3

Note. Only pe rfor m t he Clean On e D rive menu opt ion when the ACL d is plays a m essage
informing you that the tape drive needs cleaning.

Maintenance

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

5-2

Manually Running a Cleaning Cartrid ge

Manually Ru nning a Cleaning Cartridge

A cleaning cartridge can be installed and run from one of three locations:

•

A Data Cartridge Slot-This location requires removing a magazine to insert a
cleaning cartridge in a data cartridge slot and then removing it after cleaning.

•

The Cleaning Slot-This location requires reserving the last data cartridge slot for
exclusive use as a cleaning cartridge slot. The advantage with this method is that
the cleaning cartridge is stored in the unit and is always available for use. it needs
to be handled only when it expires and needs to be replaced.

Running a Cle a ni n g C a r t r i dg e f r om a Data Cartr i dge Slot

1. Install a cleaning cartridge into an appropriate data cartridge slot (Slot 0, for

example).

2. Select the Clean One Drive menu option from the Maintenance submenu on the

front panel display.

3. Select Source. If the default entry is not the slot with the cleaning cartridge, press

Slot in the Element Type box to sequence through the available cartridge slots. Or,
use the Decimal Keypad Backspace and Numeric Keys to enter the slot number
directly.

4. Select Cleaning. If the default entry is not the tape drive to be cleaned, press Drive

in the Destination Element Type box to sequence through the available tape drive
choices. Or, use the Decimal Keypad Backspace and Nume ric Keys to enter the
tape drive number directly.

5. When the source and destination entries are correct, select Execute Clean.

Maintenance

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

5-3

Replacing a Cleaning Cartridge in a Reserved Slot

Running a Cleaning Cartridge from the Cleaning Slot

1. Reserve the cleaning car tri dge slot. S ee the section o n “S etting up Reser ved S lots”

in Chapter 3 for more information.

2. Install a cleaning cartridge in the reserved slot.

3. Select the Clean One Drive menu option from the Maintenance submenu on the

front panel display. Note that the Source window defaults to the cleaning slot (Cln'g
Slot 0).

4. Select Cleaning. If the default entry is not the tape drive to be cleaned, press Drive

in the Destination Element Type box to sequence through the available tape drive
choices. Or, use the Decimal Keypad Backspace and Nume ric Keys to enter the
tape drive number directly.

5. When the destination entry is correct, select Execute Clean.

6. When the cleaning cycle completes, the unit returns the cleaning cartridge back to

the cleaning cartridge slot. To remove the cleaning cartridge, select Magazine
Access from the unit’s Status screen.

Replacing a Cleaning Cartridge in a Reserved
Slot

When the cleaning cartridge has been used up, a message appears on the front panel
display indicating that the cleaning cartridge has expired. Examine the unit’s Status
screen to make sure that the cleaning cartridge has been unlo aded fr om t he tape drive.
If not, then unload it using the Move Media menu option from the ACL Status screen.

Replacing a Cleaning Cartridge in the Right Magazine

1. Select Magazine Access from the ACL Status screen.

2. Remove the magazine from the ACL.

3. Remove the expired cleaning cartridge from the last slot. Mark it EXPIRED and

then properly dispose of it.

4. Place a new cleaning cartridge in the last slot of the magazine.

5. Replace the right magazine.

Maintenance

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

5-4

Replacing a Cleaning Cartridge in the Right

Magazine

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-1

6 Troubleshooting

This section includes:

Platform Problems

An incorrect installation or configuration can cause platform problems. In this case, the
unit appears to be operating normally, but no data can be interchanged. You also might
or might not get an error code on the Graphical User Interface (GUI) touch screen. To
identify an error caused by this type of problem, check your installation and
configuration se tup. S ee Inst all ing an d Confi g uring the A CL Tape Drive for the N onStop

NS-Series Server for information on how to correctly install and configure the unit.

General drive errors usually result from a miscommunication between the ACL and
tape drive or a mechanical malfunction within the ACL. Both platform problems and
general drive errors display an error message and a Fault Symptom Code (FSC) on
the GUI touch screen. Use an FSC to report errors to your service provider, or in some
cases, to determine a recovery procedure.

Error Recovery

Figure 6-1 on page 6-2 outlines the recommended steps for error recovery. You should

follow this chart in all cases.
Error Recovery Procedures (ERPs) are listed in detail in Table 6-1 on page 6-3; FSCs

are listed in Table 6–2 along with their related ERPs.

Platform Problems 6-1
Error Recovery 6-1
Error Recovery Procedures 6-3
Fault Symptom Codes (FSCs) 6-3

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-2

Error Recovery

Figure 6-1. Troubleshooting Flow Chart

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-3

Error Recovery Procedures

Error Recovery Procedures

Table 6-1 lists ERPs for errors reported on the GUI touch screen of the ACL. This list

includes only procedures that can be safely performed by an end user.

Fault Symptom Codes (FSCs)

FCSs that appear on the GUI touch screen are described in the below tables. A
descriptive message and instructions for clearing the fault accompany each FSC. If a
fault persists, look up the FSC in Table 6-1 on page 6-3 to determine the error recovery
procedure or to report it to your service provider.

Table 6-1. Error Recovery Procedures

ERP Code Procedure/Description

C Cycle power to the ACL using the Power option on the GUI

touch screen. Wa it 30 seconds to power on again.

D Turn off power to th e AC L and insp ec t co nnectors and

cables.
F Invalid operation. Select parameters correctly and try again.
G Call Technical Support.

Table 6-2. Fault Symptom Codes

Message FSC ERP

Novram U pdate Erro r 0306 G The non-volatile conf iguration a rea in

flas h m em or y c ould not be updated
(programming erro r).

Barcode Not Active
Error

0501 D, G Catastrophic Smx operating system error

- task creation error, unexpected error.

OS Task Exit Error 0902 G SmxNet (Ethernet, Web TLC) task error -

server spawn error, TCP/IP fatal error.

Invalid Ethernet
(MAC) Ad dress

0A01 F The ACL's Ethernet (MAC) address

stored in the non-vo lat ile configura ti on is
not valid - the last 3 octets are either 0:0:0
or 255:255:255.

Invalid IP Subnet
Mask
(255.255.255.255)

0A02 F The Ethernet subnet mask stored in the

non-volat ile configuration is not v alid -

255.255.255.255.

SCSI Firm w are Error 1001 D, G Internal SCSI task processin g error -

unexpected state or hardware status.

SCSI FIFO Empty 1002 D, G The SCSI con t roller data FIFO is empty

but should contain more data bytes.

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-4

Fault Symptom Codes (FSCs)

SCSI FIFO Error 1003 D, G The SC SI controll er data FIFO should be

empty but still co ntains data bytes.

SCSI Gross Error 1 004 C, D, G The SCSI controller detected a gross

error condition - invalid SCSI bus phase
or DMA error.

Illegal SCSI Cnt Cmd 1005 C, D, G Either an invalid command was sent to

the SCSI controller, or the controller was
not in the correct mode.

SCSI Inva lid Elemen t 1 007 D, G Internal SCSI task processin g error -

invalid element type was detected.

SCSI Invalid Int. 1 009 D, G The SCSI controller posted an invalid

interrupt stat us .

Loader Not Ready 2004 C, G Fail to fetch, stow, scan, move passthru,

Or when loader detects invalid command,
aborts command.

Door Open (status
only)

2009 F Door is force opened or door se ns or

failed.

Cart Inaccessible 200C F For an LTO, indicates the ta pe is not

ejected . Cartridge in driv e is not
accessible from changer .

Drive In Error 200D C, G A genera l driv e error det ec t ed by control

task.

No Magazine 200E F Cannot move, element not installed, from

changer.

Removal Prevented 200F F Rece iv e m edium prevent removal from

drive for a fetch.

Ctl. Firmw are Error 2 010 C, G Internal inter task p roc essing error.

Unexpected event. SMX send or receive

error.
Drive Time-out Error 2030 C, G Can’t comm unicate wi th D LT drive.
Drive Code Update

Command Error

2080 C, G Update code from SCSI or from TAPE

failed.
Move Command

Failure

2081 C, G Mo ve command from / to drive slot failed,

detected by control task.
Open Mail Slot Fault 2090 C, G Door open sensor time-out detected when

open door.
Open Left Door Fault 2091 C, G Door open sensor time-out detected when

open door.
Open Right Door Fau lt 209 2 C, G Door open sensor time-out detected when

open door.

Table 6-2. Fault Symptom Codes

Message FSC ERP

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-5

Fault Symptom Codes (FSCs)

Open Doors Fault 2093 C, G Door open sensor time-out detected when

open door.
Open DLT Handle

Fault

2094 C, G Failed to open DLT handle.

No IP Addr es s F ound 20a0 C, G SM C router failed t o get an IP address.
No IP Address Mode

Fault

20a1 C, G SM C router failed to detected static or ip

address Mode.
Unknown exchange

for the async
message

20b0 C, G Unexpec te d exchange detected w hen

process M essages .

Drive In Error 20c0 C, G Control failed to set SCSI id.
Drive In Error 20c1 C, G Control failed to installed drive .
Drive In Error 20c0 C, G Control failed to set SCSI id.
Drive In Error 20c1 C, G Control failed to installed drive .
Motor Fault Condition 3000 C, G One of the motors has been disabled and

could not be re-enabled.
Picker Tach Errors 3002 C, G Picker Tach errors were detected when

checking slots.
Bin Fetch Failure 3001 C, G Loader failed to fetch a cartridge from a

bin.
Drive Fetch Failure 3013 C, G Loader failed to fetch a cartridge from the

drive.
Drive Time-out F ailure 3015 C, D, G Loader det ec ts unload command tim e-

out.
Drive Status Failure 3016 C, D, G Det ected driv e error from fe tch, stow and

wait fo r handle ok D LT drive operation.
Drive In Flux Time-out 3 017 C, D, G Time-out waiting for drive to clear the flux

status.
Driv e Load Retr y

Failed

3018 C, G LTO drive fail to load, detected in drive

task.
Driv e OpenDoor

Failed

3019 C, G Failed open DLT door.

Drive Close Door
Failed

301A C, G Failed close DLT drive door.

Drive Communication
Error

301B C, D, G Intertask send, receive failed.

Drive Get General
S tatus Fail

301C C, D, G Drive communication failed.

Drive Get Status 3 Fail 301D C, D, G NOT USED

Table 6-2. Fault Symptom Codes

Message FSC ERP

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-6

Fault Symptom Codes (FSCs)

Undefined Config 3020 C, G In loader, unexpected config, not a

Thunder or Lightning.
Orphan Cartridge n ot

flowed

3030 C, G The loader could not successfully stow an

orphan cartridge to a bin.
Chassis S/N

Mismatch. Previous
S/N retained

3031 G The serial number scanned from the

barcode label does n't ma t c h th e v alue

stored in non-volatile memory.
Chassis S/N

Character count is not
correct

3032 G A valid ser ial number ba rc ode label co uld

not be read.

Chassis S/N did not
scan

3033 G A valid ser ial number ba rc ode label co uld

not be read
Chassis S/N save

operation failed

3034 G The serial number scanned from the

barcode label could not be saved to non-

volatile memory.
Motor Firm w are Error 3040 C, G T he loader task det ected an une x pected

status and could not recover (internal

target error).
Loader Received

Invalid Com mand

3041 C, G The loader task received an unexpected

command and cou ld not recover (int ernal

target error).
Motor Firm w are Error 3042 C, G T he loader task det ected an une x pected

status and could not recover (internal

target error).
Missing Magazine 3050 F In diag, no magazine installed for diag to

run.
No Cartridges In ACL 3051 F No cartridge available for dia g to run.
Too Many Cartridges 3052 F Unable to run cart or drive cycle, loader is

full with cartridges.
Need 1 Drive

Minimum

3054 F No ava ilable drive t o run diag.

Invalid Magazine Type 3057 F Unsupported Magazine type detected.
Magazine Type

Change Not Handled

3058 F Unsupported magazine type detected.

Drive Typ e Not
Supported

3059 F Unsupported drive type detected.

Diag Fetch, Drive not
loaded

305b F Diag: No cartridge present for a fetch.

Diag Time-out waiting
for drive empty, ready

305d F Fetch, time-out waiting for drive unload.

Table 6-2. Fault Symptom Codes

Message FSC ERP

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-7

Fault Symptom Codes (FSCs)

Invalid bin number 305f F Invalid bi n number de te c te d in diag.
Zone Sequence Error 3060 C, G Eject command time-out.
Driv e 0 Eject Failed 3074 C, G Eject command time-out.
Drive 1 Eject Fail 3075 C, D, G Eject command time-out.
Drive 2 Eject Fail 3076 C, D, G Eject command time-out.
Diag get drive 0 status

failed

3078 C, D, G Failed to get drive status, communication

error.
Diag get drive 1 status

failed

3079 C, D, G Failed to get drive status, communication

error.
Diag get drive 2 status

failed

307a C, D, G Failed to get drive status, communication

error.
Diag get drive 3 status

failed

307b C, D, G Failed to get drive status, communication

error.
Drive Stow Failed,

Media Re tu rned to
Source

3082 F The DLT drive detected an SDLT cartridge

and the cartridge has been returned to its

orign.
Drive Stow Failed,

Media Remains in
Drive

3083 F The DLT drive detected an SDLT cartridge

but the cartridge could not be returned to

its origin.
UnSupported Driv e

For Requ es t ed
Operation

3084 F Unsupported drive type.

No Retry On
Fetch/Stow

308F F The loader retrie d an operation and

retries were disabled.
Picker Jam m ed 3100 C, G The picker jammed during loade r

initialization.
Picker Jam m ed 2 310 2 C, G The picker jammed during a bin s to w

operation.
Picker Jam m ed 3 310 3 C, G The picker jammed during a bin s to w

operation.
Picker Jam m ed 4 310 4 C, G The picker jammed during a bin s to w

operation.
Picker Jam m ed 5 310 5 C, G The picker jammed during a bin s to w

operation.
Picker Jam m ed 6 310 6 C, G The picker jammed during a bin s to w

operation.
Picker Jammed 7 3107 C, G The picker jammed during a passthru

fetch operation.
Picker Jam m ed 8 310 8 C, G The picker jammed during a pass-t hru

fetch operation.

Table 6-2. Fault Symptom Codes

Message FSC ERP

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-8

Fault Symptom Codes (FSCs)

Picker Jam m ed 11 310B C, G The pick er jammed during a driv e f et c h

operation.
Picker Jammed on

Stow

310F C, G The picker jammed on a stow ope ration.

Picker retries
Exceede d 1

3111 C, G Picker retries exceeded during a pass-

thru fetc h ope r atio n .
Picker Retries

Exceede d 3

3113 C, G Picker retries exceeded during a bin stow

operation.
Picker Retraction

Error

3115 C, G The picker did not retrac t du ring a bin

check operation.
Shuttle Jammed 3 200 C, G The shuttle could not reach the target

location.
Rotary Jammed 3300 C, G The rotary track could not reach the target

location.
Shuttle on Wrong Side

Of The Rotar y

3301 C, G The zone indicators show that the shuttle

is backwa rds on the rotar y tra c k d uring

power-up initialization.
Pass through Elevator

Jammed

3400 C, G The pass-thru shuttle could not reach the

target location.
Vertical Elevator

Jammed

3500 C, G The vertical elevator c ould not reach the

target location
All Sl ots Empty 5011 F There are no ca rtridges install ed in any of

the reserved cleaning slots.
DLT Already Lo aded 5014 F The cleaning operation faile d because th e

drive already has a ca rt ridge inserte d.
Expired C lean'g Cart 5015 F The clean ing operat ion failed due to an

expired c leaning car tr idge.
Not a Clean'g Cart 5016 F The cleaning operation failed because the

loaded cartridge is not a cleaning

cartridge.
DLT Tim e-out Erro r 5035 C, D, G The cleaning operation failed becau s e the

drive timed out.
move Command Fail 503B F A front panel move operation failed.
Clean Operation

Time-out

503C F The cleaning operation failed because the

drive timed out.
Drive Status Fail 503D F The cleaning operation failed because the

ACL coul d not retrieve driv e status.
Command respon se

from unexpected
source

7001 D, G A command response was received from

a task to whic h a c om mand ha d not been

sent.

Table 6-2. Fault Symptom Codes

Message FSC ERP

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-9

Fault Symptom Codes (FSCs)

Control command
exec ut ion failed

7002 D, G A command response opcode from the

Control task was not anticipated or is un-

identifiable.
Control response not

matched to a known
command

7003 D,G A command response was received fr om

the Control task, but the original

command opcode co uld not be

determined.
Loader re s ponse not

matched to a known
command

7004 D, G A command response was received from

the Loader task, but the original command

opcode c ould not be de t erm ined.
Driv e response not

matched to a known
command

7005 D, G A command response was received from

a Drive task, b ut the original command

opcode c ould not be de t erm ined.
Flas h response not

matched to a known
command

7006 D, G A command response was received from

the Flash task, but the original command

could not be determined.
Driv e in de x on Updat e

S tatus message wa s
invalid

7007 C, D, G An Updated Drive Status message was

received fr om a m odule, bu t the drive

index was out of range.
The Drive response

was not expected

7008 C, D, G A command response was received fr om

a Drive task to which a command had not

been sent.
The opc ode for a

WORD message was
unknown

7009 C, D, G A WORD-sized message was received

but the message opcode could not be

identified.
The opc ode for a

DWORD message
was unknown

700A C, D, G A DWORD-sized message was received

but the message opcode could not

identified.
The but t on causing

ACL to go offline was
unknown

700B C, D, G A command to take the ACL offline was

completed successfully, but the GUI

button that initiated the action could not

be identified.
Destination Xchg was

Null

700C C, G Attempting to send a command to a task,

but the argument exchange pointer was

NULL.
Sendi ng of a cmd

failed

700D C, G An atte mpt to place a c ommand on a task

exchan ge f ailed.
Deactivating a dri v e

that is not atta c hed

700E C, G The Control task is indicating th at a

request to deactivate a drive failed

becaus e th e drive is not a ttac hed.

Table 6-2. Fault Symptom Codes

Message FSC ERP

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-10

Fault Symptom Codes (FSCs)

Deactivation of a drive
failed

700F C, G The Control task is indicating that a

request to deactivate a drive failed;

reason is not k nown.
Drive removal failed 7010 C, G The Drive task is indicating that a request

to power- down a drive f ailed; reason is

not known.
Drive is Active failed 7012 C, G The Drive task is indicating that a request

to determine if a drive is ex ec uting a host

command failed; reason is not kn ow n.
Control Com

Unidentified

7013 C, G During Hot Sw ap, a command resp ons e

from the Control task could not be

associat ed with any o utsta nding

command.
Driv e s tatus updated

failed

7014 C, G The Drive task is indicating that a request

to determine the current state of a driv e

failed; reason is not known.
Loader com mand

exec ut ion failed

7015 C, G The Loader task is indicating that a

command has failed to complete

successfully.
Sequen tia l c om m and

exec ut ion failed

7016 C, G The Seque nt ial task is indic at ing that a

command has failed to complete

successfully.
Destination Xchg for

msg. was Null

7017 C, G Attempting to send a message to a task,

but the argument exchange pointer was

Null.
Bad src mod in peg

msg

7018 C, G A message was received from a remote

module, but t he m odule num ber was out

of range.
A Peg message has a

pointer to Null.

7019 C, G Peg message wrapping a Null msg. ptr.

Xchg conversion
failed

701A C, G Attempt to determine the module number

containing the task that is returning a

command respon se fa iled.
Inva lid L -dr iv e nu mbe r

to convert

701B C, G Attempt to send a command to a drive,

but the log ic al drive number is out of

range.
Invalid P-drive number

to convert

701C C, G Attempt to send a command to a drive,

but the physical drive number is out of

range.
Invalid mod number to

convert

701D C, G Attempt to send a command to a drive in

a remote module, but the module number

is out of range.

Table 6-2. Fault Symptom Codes

Message FSC ERP

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-11

Fault Symptom Codes (FSCs)

Unknown 701E C, G Attempt to show detailed drive status of a

drive who s e t y pe is unknown.
The SCSI response

was not expected

701F C, G The command response from the SCSI

task in a remote module was unexpected.
The Flash response

was not expected

7020 C, G The command response from the Flash

task in a remote module was unexpected.
SCSI response not

matched to a known
command

7021 C, G A command response was received from

a SCSI task, but the original command

opcode c ould not be de t erm ined.
Unexpected state after

NonVo l Confi g cmd

7022 C, G After successfully completing a

NonVolCofigPut c om m and, the cu rrent

state of the sa v e operation w as unknown
Unexpected state after

SCSI mode cmd

7023 C, G After successfully completing a

SCSIUpdateModeParameters command,

the current sta te of the save operation

was unknown.
Unexpected state after

SCSI init cmd

7024 C, G After successfully completing a

SCSIInitcommand, the current sta te of the

save operation was unknown.
Cartridg e reject

recovery failed

8001 C, D, G The DL T dri ve faile d to successfull y load

a tape even after retries.
Drive Fan s tall ed 8002 C, D, G The fan in the driv e hot-swa p s hoe is

either not insta lled or has stalled.
Driv e load did no t

complete

8003 C, D, G The drive failed to successfully load a

tape.
Invalid dri v e w as

installed

8004 F One or more installed drives are of a type

either unk nown or not s upported in th e

current A C L personali ty.
LTO unmask drive

failed

8005 F The LTO drive unmask operation fa iled.

LTO mask drive failed 800 6 F The LTO drive mask o peration failed.
LTO unload drive (I n

load retry ) fa iled

8007 F The LTO drive failed to u nload a cartridge

during a lo ad retry operation.
Is Drive Unloaded

Failed

8008 F The LTO driv e failed to r eturn status when

being po lled for unloa ded state.
Orphan cartridge

recovery failed

9001 C, D, G The master module could not successfully

return an orphan car tr idge to a slot

location.
Master pass-thru opto

failed

9003 C, D, G The master module opto sensor was not

detected during the power-up pass-t hru

module inv entory.

Table 6-2. Fault Symptom Codes

Message FSC ERP

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-12

Fault Symptom Codes (FSCs)

SMX send error A 001 C, G An at t em pt to place a me s s age on a

tas k ’s exchange generated a kernel error.
SMX receive error A002 C, G An attempt to receive a message from a

tas k ’s exchange generated a kernel error.
Comm free list empty A003 C, G An attempt to acquir e a message fr o m th e

free pool f ailed becau s e th e pool is empt y.
Invalid comm. put

attempt

A004 C, G An attempt to place a message on a

task’s exchange failed because either the

argument message pointer was NULL or

the argument exchange pointer was

NULL.
Invalid comm. get

attempt

A005 C, G An attempt to receive a message from a

task’s exchange failed because the

argument exchan ge pointer was N U LL.
Comm initialization

error

A006 C, G The Com m m anager co uld not be

initialize d at power-up because the

system is out of memory.
Put of a NUL L c om m. A007 C, G An attemp t to place a Com m block on a

task’s exchan ge failed the argumen t

Comm block pointer was NULL.
Msg contain s no

comm.

A008 C, G A mess age obtained from the free pool

did not con tai n a C omm block.
Comm return address

in unknown

A009 C, G An attempt to return a command

response to the originating task failed

becaus e th e originato r co uld not be

determined.
Bad Imag e C R C F001 F The uploaded fir m w are image h as a bad

CRC and is probably corrupted.
Flas h erase sect or

failed

F002 F One of the flash memory sectors could

not be programmed.
Flas h program s ec t or

failed

F003 C, G O ne of the flash memory sectors could

not be erased.
Bad flash CRC F004 C, G The firmw are image p rogrammed into

flash memory has a bad CRC and is

probabl y corrupted .
Flash exit error F005 C, G Internal flash task error.
Incompati ble image F006 F The uploaded firmwar e im age is not

compatible with the ACL hardware,

possibly an older firmware version.
Buffer allocation failed F402 F The flash task could not allocate a buffer

area to hold the firmware image to be

uploaded.

Table 6-2. Fault Symptom Codes

Message FSC ERP

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-13

Fault Symptom Codes (FSCs)

If an error message appears that is not included in Table 6-2, write down the fault code
number and follow the recovery procedure. If the same error occurs again, call your
service provider.

Troubleshooting

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

6-14

Fault Symptom Codes (FSCs)

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

Statements-1

Safety and Compliance

This sections contains three types of required safety and compliance statements:

•

Regulatory compliance

•

Waste Electrical and Electronic Equipment (WEEE)

•

Safety

Regulatory Compliance Statements

The following regulatory compliance statements apply to the products documented by
this manual.

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio-frequency energy and, if not installed and used in accordance with the
instruction manual, may cause interfer ence to radio communications. Operation of this
equipment in a residenti al area is likely to cause harm ful interfer ence i n which case the
user will be required to correct the interference at his own expense.

Any changes or modifications not expressly approved by Hewlett-Packard Computer
Corporation could void the user’s authority to operate this equipment.

Canadian Compliance

This class A digita l apparatus meets all the requirements of the Canadian Interference­Causing Equipment Regulations.

Cet appare il numér i que d e la classe A r especte toutes le s exigence s du Rège lment sur
le matériel brouilleur du Canada.

Safety and Compliance

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

Statements-2

Regulatory Compliance Statements

Korea MIC Compliance

Taiwan (BSMI) Compliance

Japan (VCCI) Compliance

This is a Class A product based on the standard or the Voluntary Control Council for
Interference by Information Technology Equipment (VCCI). If this equipment is used in
a domestic environment, radio disturbance may occur, in which case the user may be
required to take corrective actions.

Safety and Compliance

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

Statements-3

Regulatory Compliance Statements

European Union Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and
the Low Voltage Directive (73/23/EEC) issued by the Commission of the European
Community .

Compliance with these directives implies conformity to the following European Norms
(the equivalent international standards are in parenthesis):

•

EN55022 (CISPR 22)—Electromagnetic Interference

•

EN55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11)—Electromagnetic Immunity

•

EN61000-3-2 (IEC61000-3-2)—Power Line Harmonics

•

EN61000-3-3 (IEC61000-3-3)—Power Line Flicker

•

EN60950 (IEC950)—Product Safety

Laser Compliance

This product may be provided with an optical storage device (that is, CD or DVD drive)
and/or fiber optic transceiver. Each of these devices contains a laser that is classified
as a Class 1 Laser Product in accordance with US FDA regulations and the IEC
60825-1. The product does not emit hazardous laser radiation.

The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug
Administration implemented regulations for laser products on August 2, 1976. These
regulations apply to laser products manufactured from August 1, 1976. Compliance is
mandatory for products marketed in the Unites States.

W ARNING: Use the controls or adjustment s or performance of
procedures other than those specified herein or in the laser
product’ s installation guide may result in hazardous radiation
exposure. To reduce the risk of exposure to hazardous
radiation:

•

Do not try to open the module enclosure. There are no
user-serviceable components inside.

•

Do not operate controls, make adjustments, or perform
procedures to the laser device other than those specified
herein.

•

Allow only HP Authorized Service technicians to repair
the module.

Safety and Compliance

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

Statements-4

SAFETY CAUTION

SAFETY CAUTION

The following icon or caution statements may be placed on equipment to indicate the
presence of potentially hazardous conditions:

DOUBLE POLE FUSING

CAUTION: DOUBLE-POLE /NEUTRAL FUSING.
ATTENTION: DOUBLE POLE/FUSIBLE SUR LE NEUTRE

NOT FOR EXTERNAL USE

CAUTION: NOT FOR EXTERNAL USE . ALL RECEPTA C LES ARE FOR INTERNAL
USE ONL Y.

ATTENTION: NE PAS UTILISER A L’EXTERIEUR DE L’EQUIPEM ENT
IMPORTANT: TOUS LES RECIPIENTS SONT DESTINES UNIQUEME NT A UN

USAGE INTERNE.
VORSICHT: ALLE STECKDOSEN DIENEN NUR DEM INTERNEN GEBRAUCH.

DUAL POWER CORDS CAUTION:
“THIS UNIT HAS MORE THAN ONE POWER SUPPLY CORD.

DISCONNECT ALL POWER SUPPLY CORDS TO COMPLETELY
REMOVE POWER FROM THIS UNIT."

"ATTENTION: CET APPAREIL COMPORTE PLUS D'UN CORDON
D'ALIMENTATION. DÉBRANCHER TOUS LES CORDONS
D'ALIMENTATION AFIN DE COUPER COMPLÈTEMENT
L'ALIMEN TATION DE CE T ÉQUIPEM EN T ".

DIESES GERÄT HAT MEHR ALS EIN NETZKABEL. VOR DER
WARTUNG BITTE ALLE N ET Z KABEL AUS DER STECKDOSE
ZIEHEN.

Any surface or area of the equipment marked with these symbols
indicates the presence of electric shock hazards. The enclosed area
contains no operator-serviceable parts.

WARNING: To reduce the risk of injury from electric shock hazards, do
not open this enclosure.

Safety and Compliance

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

Statements-5

Waste Electrical and Electronic Equipment (WEEE)

HIGH LEAKAGE CURRENT

To reduce the risk of electric shock due to high leakage currents, a reliable grounded
(earthed) connection should be checked before servicing the power distribution unit
(PDU).

Observe the following limits when connecting the product to AC power distribution
devices: For PDUs that have attached AC power cords or are directly wired to the
building power, the total combined leakage current should not exceed 5 percent of the
rated input current for the device.

“HIGH LEAKAGE CURRENT, EARTH CONNECTION ESSENTIAL BEFORE
CONNECTING SUPPLY”

“HOHER ABLEITSTROM. VOR INBETRIEBNAHME UNBEDINGT
ERDUNGSVERBINDUNG HERSTELLEN”

“COURANT DE FUITE E’LEVE’. RACCORDEMENT A LA TERRE INDISPENSABLE
AVANT LE RACCORDEMENT AU RESEAU”

FUSE REPLACEMENT

CAUTION – For continued protection against risk of fire, replace only with same fuse
type TCF15, Rated 600V~, 15A. Disconnect power before changing fuses.

Waste Electrical and Electronic Equipment
(WEEE)

Information about the Waste Electrical and Electronic Equipment (WEEE) directive can
be accessed from the left navigation area of the NTL home page: select NonStop

Computing > Waste Electrical and Electronic Equipment (WEEE).

Important Safety Information

Safety information can be accessed from the left navigation area of the NTL home
page: select NonStop Computing>Important Safety Information. A document
window containing a binder of safety information, in several languages, appears. In the
document window, click a document title to open the safety information in another
language. Local HP support can also help direct you to your safety information.

Safety and Compliance

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

Statements-6

Important Safety Information

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

Index -1

Index

A

ACL rackmount 2-1
ACL tabletop 2-5

B

Barcode reader 1-4, 1-5

F

Fiber optic cable 1-1, 3-3
Fibre Channel ServerNet adapter 1-1, 3-5
Front panel indicators 1-6, 4-2

GUI touch screen 1-4, 1-6, 3-5, 4-2

access magazine option 4-6
default screen 4-4
initialization screen 4-3
menu selections 4-10
move media 4-6
status screen 4-9

viewing window 1-6

L

LTO Ultrium gen 3 tape drive 1-1

M

Magazine door 4-2
Maintenance 5-1

N

NonStop NS-series server

configuration 3-7
installation 3-3

P

Portname 3-10
POST 4-3

Power supply 1-4

R

Robotics 1-4

S

Shuttle assembly 1-5
Supported connections 3-3

T

Tape cartridge magazine 1-2, 1-4, 4-14
Tape cartridges

barcode labels 4-14
inserting and removing 4-13

Troubleshooting 6-1

Index

M8501 and M8502 ACL T ape Drive Installation and User’s Guide—529972-001

Index -2

T