Uncompromising 8-way performance and availability in an ultra dense, 4U form factor
Intel Xeon Processor MP 3.0GHz/4MB, 2.7GHz/2MB, 2.2GHz/2MB, 2.8 GHz/2MB, 2.5GHz/1MB Processors (eight processor capability)
HP developed F8 chipset
133 MHz SDRAM Memory, expandable to 64 GB addressable memory
HP Hot Plug RAID Memory Technology
Hot Add, Hot Replace, and Hot Upgrade
Uses industry standard ECC-protected memory
Six 64 bit/100MHz PCI-X slots, all hot pluggable
Integrated Lights-Out Standard Management (iLO) on system board
Two NC7781 PCI-X Gigabit NICs (embedded)
Integrated Smart Array 5i Controller (Ultra3 support) (supports RAID 0, 1, 1+0, and 5 across internal hard disk drives)
Internal Hot Plug Drive Storage of 584.2 GB (4 x 1" 146.8-GB Ultra320 hard drives running Wide Ultra3)
Tool less and modular chassis for enhanced serviceability
Innovative diagnostic lighting for rapid response to service events
Unit ID (UID) lighting, front and rear
Front bezel system health/RAID memory LEDs
Two 1100W/800W hot plug redundant power supplies standard
Two hot plug redundant system fans standard
Rapid deployment racking solution (rack rails and cable management)
Available with 2.0 GHz or 2.7 GHz, 2.2GHz or 2.8GHz models.)
NOTE:NOTE:
1-MB Integrated Level 3 cache (per processor)
(
NOTE:
NOTE:
Available with 1.5 GHz, 2.5GHz or 2.0 GHz models.)
NOTE:NOTE:
Upgradeable to eight processors
HP developed F8 chipset
Standard
Maximum
Standard
Maximum
NOTE:
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
NOTE: NOTE:
by the OS. Total memory consists of addressable memory plus the redundant memory (stored in the dedicated parity memory
cartridge.)
All models come standard with all five memory cartridges populated and Hot Plug RAID Memory enabled.
In standard Hot Plug RAID Memory mode, addressable memory refers to the portion of memory that is addressable
587.2 GB (4 x 146.8 GB Ultra320 1" Drives) (internal hot plug cage only)
1
1
1
1
1
1
2
Graphics
Graphics
GraphicsGraphics
Form Factor
Form Factor
Form FactorForm Factor
Integrated ATI RAGE XL Video Controller with 8-MB SDRAM Video Memory
4U (7") Rack Form Factor; Ships with sliding rack rails and cable management system; Standard 19" rack-mountable
DA - 11585 Worldwide — Version 33 — July 16, 2004
Page 3
QuickSpecs
Standard Features
ProLiant
ProLiant
ProLiantProLiant
Foundation Pack
Foundation Pack
Foundation PackFoundation Pack
Software
Software
SoftwareSoftware
Essentials
Essentials
Essentials Essentials
Insight Manager 7 and HP
Systems Insight Manger
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
Insight Manager 7 and HP's new HP Systems Insight Manager help maximize system
uptime and performance and reduce system maintenance costs by providing proactive
notification of problems before those problems result in unplanned downtime or reduced
productivity. Insight Manager 7 and HP Systems Insight Manager are both easy to set up
work with the Insight Management Agents, integrated Light-Out and Remote Insight LightOut Edition, and Version Control Agents to deliver robust fault, configuration, and asset
management as well as remote administration. With HP Systems Insight Manager
customers will also be able to take advantage of role-based security; the ability to manage
ProLiant, Integrity, and HP9000 systems; and plug-ins for storage, client, printer, and
power management as well as server rapid deployment, performance management, and
workload management. For more details on HP Systems Insight Manager visit
http://www.hp.com/go/hpsim
SmartStart
Management Agents
Subscriber's Choice
ROMPaq
and
configuration utilities
Survey Utility and diagnostics
utilities
Optional
Value Packs
NOTE:
NOTE:
NOTE: NOTE:
http://www.hp.com/servers/proliantessentials
information.
NOTE:
NOTE:
NOTE: NOTE:
http://www.hp.com/servers/proliantessentials
, support software,
ProLiant Essentials
Flexible and volume quantity license kits are available for ProLiant Essentials Value Packs. Refer to
For more information regarding ProLiant Essentials Software, please see the following URL:
SmartStart is a tool that simplifies server setup, providing a rapid way to deploy reliable
and consistent server configurations. For more information, please visit the SmartStart Web
site at
http://www.hp.com/servers/smartstart
SmartStart version supported (minimum): SmartStart 6.20.
The Management Agents form the foundation for HP's Intelligent Manageability strategy.
They provide direct, browser-based access to in-depth instrumentation built into HP servers,
workstations, desktops, and portables, and send alerts to Insight Manager 7 and other
enterprise management applications in case of subsystem or environmental failures. For
additional information about the Management Agents and other management products
from HP, please visit the management Web site at
Subscriber's Choice Driver and Support Alerts/Notifications is a web-based email
subscription service that provides automatic delivery of software and driver change
notifications for ProLiant products. Sign up at
and customize your profile to receive various new alerts as they become available, on a
weekly or monthly basis.
The latest software, drivers, and firmware fully optimized and tested for your ProLiant server
and options available in SmartStart or downloadable from Software and Drivers download
pages, linked from the SmartStart website at
The most advanced configuration analysis, reporting and troubleshooting utilities used by
HP and at your fingertips, available in SmartStart.
Optional software offerings that selectively extend the functionality of an Adaptive
Infrastructure to address specific business problems and needs:
Rapid Deployment Pack – an automated solution for multi-server deployment and
provisioning, enabling companies to quickly and easily adapt to changing
business demands.
Workload Management Pack – provides easier management of complex
environments, improving overall server utilization and enabling Windows® 2000
customers for the first time to confidently deploy multiple applications on a single
multiprocessor ProLiant Server.
Performance Management Pack – a performance management solution that
identifies and explains hardware performance bottlenecks on ProLiant servers and
attached options enabling users to better utilize their valuable resources.
.
http://www.hp.com/servers/manage
http://www.hp.com/go/subscriberschoice
www.hp.com/servers/smartstart
or the various ProLiant Essentials Value Pack product QuickSpecs for more
ACPI 1.0b Compliant
PCI-X and PCI 2.2 Compliant
PAE Support
PXE Support
Microsoft® Logo certifications
Integrated Lights-Out (iLO) Standard Management
Virtual Text Remote Console
Virtual Power Button Control
Dedicated LAN Connectivity
Automatic IP Configuration via DHCP/DNS/WINS
Industry Standard 128-bit Secure Sockets Layer (SSL) Security
IML and iLO Event Logging
Support for 12 user accounts with customizable access privilege
Integrated Lights-Out (iLO) Advanced Pack (supports Advanced features such as Graphical Remote Console and Virtual
Floppy - available as a separate option)
Insight Manager 7
HP Systems Insight Manager
Remote Insight Lights-Out Edition ll (optional)
ROM-Based Setup Utility (RBSU)
Integrated Management Log (IML)
Server Health logging
Automatic Server Recovery-2 (ASR-2)
System Interconnect Status Indicators
Remote-Flash Redundant ROM
Hot Spare Boot (
automatically reboot and use the remaining good processor(s).
Power Down Utility
Pre-Failure Warranty (covers processors, as well as hard drives and memory)
Dynamic sector repairing and drive parameter tracking (with Smart Array controllers)
NOTE:
NOTE:
NOTE: NOTE:
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
Upon the event of a failed processor or VRM in a multi-processing environment, the system will
)
Availability
Availability
AvailabilityAvailability
Hot Plug RAID Memory - delivering unsurpassed memory protection and server availability:
Uses industry standard ECC SDRAM DIMMs
Fully redundant architecture, with no more performance overhead than is currently experienced with ECC protection.
Same level of redundancy as achieved with memory mirroring, at only 25% of the additional memory expense when
compared to mirroring.
Customer can choose to run in non-RAID memory mode by populating only the first 4 memory cartridges.
Hot Add
Hot Add
Hot AddHot Add
Add a new bank of DIMMs while the server is running
OS/Application enabled
Hot Upgrade
Hot Upgrade
Hot UpgradeHot Upgrade
Upgrade from a lower capacity DIMM to a higher capacity DIMM while the server is running
OS/Application enabled
Hot Replace
Hot Replace
Hot ReplaceHot Replace
Replace a failed DIMM while the server is running
OS/Application transparent
Six 64bit/100MHz PCI-X Hot Plug slots with push button functionality
Dual Redundant Hot Plug Fans
Smart Array 53XX Controller (optional)
Dynamic sector repairing and drive parameter tracking (with Smart Array controllers)
Fault Tolerant Processor Power Modules
Redundant/adaptive load balancing NIC Support
Dual Redundant Hot Plug Power Supplies
DA - 11585 Worldwide — Version 33 — July 16, 2004
Page 5
QuickSpecs
Standard Features
Serviceability
Serviceability
ServiceabilityServiceability
Security
Security
SecuritySecurity
Innovative Diagnostic Lighting throughout server
Tool-less, virtually cable-less interior design
Tool-less access to interior of server
Hot pluggable universal media bay (CD/DVD-ROM drive ships standard) ejects without the use of tools
Front access power supplies
PCI Card Guides locks full length PCI cards in place during transit
SCSI Drive Cage connects directly to system board – no cables.
Modular mechanical design allows tool-less access to major subsystems for easy upgrades and servicing
Quick Deploy Racking System
Tool-less design "snap in" rails
Power-on password
Diskette drive control
Diskette boot control
Network server mode
Security provision
Parallel and serial interface control
Administrator's password
Disk configuration lock
Hot plug access security
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
LED display on front bezel indicates system health and DIMM status
LED display on memory cartridges indicates cartridge power and attention status
Host Module: Processor, Memory, and I/O Subsystems
Power and Media Module: SCSI Backplane, Power Supplies, Universal Media Bay
Server Power Cords
Server Power Cords
Server Power CordsServer Power Cords
Power Supply
Power Supply
Power SupplyPower Supply
System Fans
System Fans
System FansSystem Fans
Required Cabling
Required Cabling
Required CablingRequired Cabling
Two IEC to IEC Highline power cords (PDU adapters) ship standard
Two Redundant Hot Plug 1100/800-Watt power supplies per system. Power supplies are load sharing and provide 1100
Watts of Redundant power for 220-volt input or 800 Watts of power for 115-volt input.
NOTE:
NOTE:
NOTE: NOTE:
ensure that both power supplies can support up to their maximum configurations, and remain in a redundant power supply
state.
NOTE:
NOTE:
NOTE:NOTE:
recommended.
NOTE:
NOTE:
NOTE: NOTE:
supported on all server configurations when using 115-120 VAC power. Please refer to the Power Supply Calculator
http://activeanswers.compaq.com/
NOTE:
NOTE:
NOTE: NOTE:
Two Hot-Plug redundant fans ship standard. Two maximum supported.
For required cabling information, refer to the HP Web site at:
CAUTION: CAUTION:
prevent damage to the equipment:
For a more complete and up-to-date listing of supported OS's and versions, please visit our OS Support Matrix at:
For an up-to-date listing of the latest drivers available for the HP ProLiant DL740, please see:
For a more complete and up-to-date information on Linux support, please visit HP Linux Web site at
For more complete and up-to-date information on how to buy server operating systems from HP please visit the OS
Rack 10000 series Cabinets
The increasing power of new high-performance processor technology requires increased cooling efficiency for rackmounted servers. The 10000 Series Racks provide enhanced airflow for maximum cooling, allowing these racks to
be fully loaded with servers using the latest processors..
If a third-party rack is used, observe the following additional requirements to ensure adequate airflow and to
HP Factory Express
HP Factory Express
HP Factory ExpressHP Factory Express
Capabilities
Capabilities
CapabilitiesCapabilities
Front and rear doors: If your 42U server rack includes closing front and rear doors, you must allow 830
square inches (5,350 sq cm) of hole evenly distributed from top to bottom to permit adequate airflow
(equivalent to the required 64 percent open area for ventilation).
Side: The clearance between the installed rack component and the side panels of the rack must be a
minimum of 2.75 inches (7 cm).
CAUTION:
CAUTION:
CAUTION: CAUTION:
ensures proper airflow. Using a rack without blanking panels results in improper cooling that can lead to thermal damage.
NOTE:
NOTE:
NOTE: NOTE:
server, or to the server documentation located in the Support section at the following URL:
NOTE: NOTE:
and removal. This applies to both individual rack installations as well as when aligning rack rows so that the front doors
are facing each other.
HP Factory Express gives you the flexibility to choose from a full menu of factory capabilities all in one manufacturing
facility, in one process, with one touch giving you full control and access to HP's World class manufacturing facility
anytime. This approach provides you the speed to deploy your IT needs, with total quality assurance, reliability, and
predictability to lower your total cost of ownership by letting HP install, rack, and customize your software and hardware
options for you.
Always use blanking panels to fill all remaining empty front panel U-spaces in the rack. This arrangement
For additional information, refer to the Setup and Installation Guide or the Documentation CD provided with the
.
Allow a minimum of 48 inches (121.92 cm) clearance beyond the front of your rack to permit server installation
DA - 11585 Worldwide — Version 33 — July 16, 2004
Page 7
QuickSpecs
Standard Features
Service and Support
Service and Support
Service and SupportService and Support
Three-year limited warranty, including hardware diagnostic support, pre-failure warranty (coverage of hard drives, memory
and processors). The warranty is fully supported by HP Services and a worldwide network of resellers and service providers. In
addition 90-day's getting started software telephone support may be covered under the warranty or available for an
additional fee. Enhancements to warranty services are available through HP Care Pack services.
NOTE:
NOTE:
Limited warranty includes 3 year parts, 3 year labor, 3-year on-site support
NOTE:NOTE:
Care Pack services provide a range of life cycle support options that let you choose the service levels that meet your business
requirements, from basic to mission-critical.
A full range of HP Care Pack hardware and software services are available including:
Installation and start up
Education courses
Extended onsite hardware coverage hours from same business day 13 hours, 5 day to 24 hours, 7 days call window
with options including 4-hour response or 6-hour Call To Repair
Comprehensive range of software technical support for Microsoft, Linux, ProLiant Essentials and VMWare-based IT
solutions helping to deliver high level of application availability. Response times range from 30 mins for critical
problems to 2 hours.
System Management, Performance Services and Mission Critical Support Solution
HP Care Pack Services include HP branded hardware options qualified for the server, purchased at the same time or
afterwards, internal to the enclosure, as well as 22" and smaller external monitors and tower UPS options up to 3KVA. 22"
and smaller external monitors will be covered at the same service level and coverage period as the server. For servers or
storage systems installed within a rack, service also covers all HP qualified rack options installed within the same rack.
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
NOTE:
NOTE:
For more information on HP Care Pack services, contact any of our worldwide sales offices or resellers or visit our
NOTE:NOTE:
worldwide Web site on the internet at:
NOTE:
NOTE:
For more complete information on HP Services offerings, customers and resellers, please visit us
NOTE:NOTE:
at:
http://www.hp.com/hps
NOTE:
NOTE:
Additional information regarding worldwide limited warranty and technical support is available at:
ProLiant EssentialsProLiant Essentials
Value Pack Software
Value Pack Software
Value Pack SoftwareValue Pack Software
Low Line (115V) Cable Kit, C-13 to 5-15P
DL740 Folding Metal Cable Management Arm
*
NOTE:
NOTE:
NOTE: NOTE:
highly recommends running your DL740 at high line (220V) voltage to ensure power redundancy for
all of your robust, business-critical configurations. Because of the increasing power requirements of
the memory and microprocessor subsystems, the DL740 does not support power redundancy for all
configurations when running at low line voltage. Please refer to the Power Supply Calculator
http://activeanswers.compaq.com/
ProLiant Essentials Performance Management Pack Single Server License
NOTE:
NOTE:
This license allows 1 server to be managed by Performance Management Pack.
NOTE:NOTE:
Performance Management Pack, flexible license kit
NOTE:
NOTE:
A single pack is shipped with a single license key for the total number of licenses ordered.
NOTE: NOTE:
Refer to http://www.hp.com/servers/proliantessentials or the various ProLiant Essentials Value Pack
product QuickSpecs for more information.
NOTE:
NOTE:
NOTE: NOTE:
http://www.hp.com/servers/proliantessentials
Flexible and volume quantity license kits are available for ProLiant Essentials Value Packs.
For more information regarding ProLiant Essentials Software, please see the following URL:
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
The Low Line Cable Kit consists of a single, 9 foot, IEC C-13 to 5-15P, 10 Amp cord. HP
to determine if your low line configuration is redundant.
.
317424-001
321716-B21
306696-B21
306697-B21
303284-B21
263825-B21
HP NetServer integration
HP NetServer integration
HP NetServer integrationHP NetServer integration
Services
Services
ServicesServices
HP NetServer to ProLiant integration and assessment service
NOTE:
NOTE:
NOTE: NOTE:
helps maximize customer's ability to add ProLiant platforms into their current environment.
HP TopTools to Insight Manager 7 installation and startup service
NOTE:
NOTE:
NOTE: NOTE:
will also re-create, as closely as possible, the views and reports from the customer's current TopTools
configuration. This service assures a smooth transition to the ProLiant Essentials software.
HP identifies current levels of NetServer support, services, and management. This service
Provides on-site review, installation and configuration services for Insight Manager 7. HP
Ultra2 when not used with the Wide Ultra3 hard drives.
Ultra320 Expansion Module for SA-6402
NOTE:
NOTE:
NOTE: NOTE:
such as PCI Bus, PCI Peak Data Transfer Rate, SCSI Protocols supported, SCSI Peak Data Transfer
Rate, Channels, SCSI Ports, Drives supported, Cache, RAID support, and additional information:
NC6170 Dual Port PCI-X 1000SX Gigabit Server Adapter
NC6770 PCI-X Gigabit Server Adapter, 1000-SX
NC7170 Dual Port PCI-X 1000T Gigabit Server Adapter
NC7771 PCI-X Gigabit Server Adapter
NOTE:
NOTE:
NOTE: NOTE:
Controller
Remote Insight Lights-Out Edition II (NA, LA)
Remote Insight Lights-Out Edition II (EMEA)
Remote Insight Lights-Out Edition II (ROW)
HP/Atalla AXL600L SSL Accelerator Card for ProLiant Servers
Compaq AXL300 Accelerator PCI Card (HW SSL Encryption) for ProLiant Servers
External, Rack-Mount, and Array Module Ultrium Tape Drives
External, Rack-Mount, and Array Module Ultrium Tape Drives
External, Rack-Mount, and Array Module Ultrium Tape DrivesExternal, Rack-Mount, and Array Module Ultrium Tape Drives
HP StorageWorks Ultrium 215 Tape Drive, External (Carbon)
Any NIC on the option list can be used for redundancy with the embedded NC7781 Network
DA - 11585 Worldwide — Version 33 — July 16, 2004
313879-B21
244949-B21
313881-B21
290563-B21
227251-001
227251-021
227251-371
524545-B21
227933-B21
Q1545A
Page 13
QuickSpecs
Options
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
HP StorageWorks Ultrium 215 rack-mount (Carbon) - Single drive installed in a 3U rack-mount kit
HP StorageWorks Ultrium 215 Array Module (Carbon) - Offline hot-swap drive for Tape Array 5300
HP StorageWorks Ultrium 230 Tape Drive, External (Carbon)
HP StorageWorks Ultrium 230, Rack-mount (Carbon) - Single drive installed in a 3U rack-mount kit
HP StorageWorks Ultrium 230 Array Module (Carbon) - Offline hot-swap drive for Tape Array 5300
HP StorageWorks Ultrium 460 Tape Drive, External (Carbon)
HP StorageWorks Ultrium 460, Rack-mount (Carbon) - Single drive installed in a 3U rack-mount kit
HP StorageWorks Ultrium 460 Array Module (Carbon) - Offline hot-swap drive for Tape Array 5300
NOTE:
NOTE:
NOTE: NOTE:
additional options such as controllers, media, and other related items:
(North America)
For an up-to-date listing of the latest O/S and software support details for HP Ultrium tape drives,
please visit:
External, Hot-Plug, and Array Module DAT Drives
External, Hot-Plug, and Array Module DAT Drives
External, Hot-Plug, and Array Module DAT DrivesExternal, Hot-Plug, and Array Module DAT Drives
HP StorageWorks DAT 72 Tape Drive, External (Carbon)
HP StorageWorks DAT 72 Tape Drive, Internal Hot-Plug (Carbon)
HP StorageWorks DAT 72 Array Module (Carbon) - Offline hot-swap drive for Tape Array 5300
HP StorageWorks DAT 40 Tape Drive, External (Carbon)
HP StorageWorks DAT 40 Tape Drive, Internal Hot-Plug (Carbon)
HP StorageWorks DAT 40 Array Module (Carbon) - Offline hot-swap drive for Tape Array 5300
HP StorageWorks DAT 24e Tape Drive, External (Flint)
HP StorageWorks DAT 24 Array Module (Carbon) - Offline hot-swap drive for Tape Array 5300
StorageWorks SAN Switch 2/8-EL
StorageWorks SAN Switch 2/16
StorageWorks SAN Switch 2/8-EL Upgrade Kit
StorageWorks SAN Switch 2/16-EL Upgrade Kit
StorageWorks Director 2/64
Uninterruptible PowerUninterruptible Power
Systems – Rack Mountable
Systems – Rack Mountable
Systems – Rack MountableSystems – Rack Mountable
Please see the UPS and PDU cable matrix that lists cable descriptions, requirements, and
Please see the UPS and PDU cable matrix that lists cable descriptions, requirements, and
Please see the UPS and PDU cable matrix that lists cable descriptions, requirements, andPlease see the UPS and PDU cable matrix that lists cable descriptions, requirements, and
specifications for UPS and PDU units.
specifications for UPS and PDU units.
specifications for UPS and PDU units.specifications for UPS and PDU units.
HP UPS R1500 XR (1440VA, 1340 Watt), Low Voltage (NA)
HP UPS R3000 XR (2880VA, 2700 Watt), Low Voltage (NA)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage (NA)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage (Japan)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage (Int’l - detachable cord)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage (16A IEC309 Plug)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage (16A CEE 7/7 SCHUKO Plug)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage (16A BS-546 Plug)
HP UPS R5500 XR, (5000VA, 4500 Watt), High Voltage (NA/Jpn)
HP UPS R5500 XR, (6000VA, 5400 Watt), High Voltage (Int'l)
Rack-Mountable UPS R6000 (6000VA, 6000 Watt) High Voltage (NA)
NOTE:
NOTE: The UPS R6000 has a hardwired input.
NOTE:NOTE:
Rack-Mountable UPS R6000 (6000VA, 6000 Watt) High Voltage (Int'l)
NOTE:
NOTE:
NOTE: NOTE:
Rack-Mountable UPS R6000 (6000VA, 6000 Watt) High Voltage (Japan)
NOTE:
NOTE:
NOTE: NOTE:
HP UPS R12000 XR N+x (200-240V) (WW-hardwired)
NOTE:
NOTE:
NOTE: NOTE:
The UPS R6000 has a hardwired input.
The UPS R6000 has a hardwired input.
The UPS R12000 XR has a hardwired input and output; requires a 100A circuit.
Please see the Enterprise Configurator for configuration assistance at:
DA - 11585 Worldwide — Version 33 — July 16, 2004
http://www.hp.com/products/configurator
.
Page 20
QuickSpecs
Options
Modular Power
Modular Power
Modular PowerModular Power
Distribution Units - 1U0U
Distribution Units - 1U0U
Distribution Units - 1U0UDistribution Units - 1U0U
(Up to 32 outlets)
NOTE:
NOTE:
NOTE: NOTE:
brackets shipped with
the unit (optimized for 10000
and 9000 series racks).
USB Options
USB Options
USB OptionsUSB Options
1U/0U mounting
HP Modular Power Distribution Units (mPDU), Low Volt Model, 24A (100-127 VAC) (NA, Japan)
NOTE:
NOTE:
NOTE: NOTE:
R3000 XR.
HP Modular Power Distribution Units (mPDU), High Volt Model, 24A (200-240 VAC) (NA, Japan)
HP Modular Power Distribution Units (mPDU), High Volt Model, 32A (200-240 VAC) (Int’l)
HP Modular Power Distribution Units (mPDU), High Volt Model, 40A (200-240 VAC) (WW)
NOTE:
NOTE:
NOTE: NOTE:
HP Modular Power Distribution Units (mPDU), High Volt Model, 16A (200-240 VAC) (WW)
NOTE:
NOTE:
NOTE: NOTE:
power requirements. This model may also be used with the high volt UPSs R3000 XR and R6000 For
North America, need to order cable PN 340653-001.
NOTE:
NOTE:
NOTE: NOTE:
QuickSpecs for additional options including shorter jumper cables and country specific power cords:
DescriptionDescription
HE
UK
ARA
FIN
DEN
ITL
BEL
BRZ
RUSS
CZE
HUNG
POL
THAI
BHCSY
SLOV
ICELAND
KAZ
SWISS
DC172B
DC141B
DA - 11585 Worldwide — Version 33 — July 16, 2004
Page 21
QuickSpecs
Options
Third Party Rack Kit
Third Party Rack Kit
Third Party Rack KitThird Party Rack Kit
Third Party Rack Kit
NOTE:
NOTE:
The Third party rack kit supports the ML530 G2, ML570 G2, DL740, and DL760 G2.
NOTE:NOTE:
Provides support for any rack, square hole or round hole (including HP Rack System /E and HP
Systems) with an adjustment range from 23 ½" – 34" deep.
NOTE:
NOTE:
NOTE: NOTE:
conform to the adjustment range of the standard rail that ships with the server.
Telco Rack Support:
NOTE:
NOTE:
NOTE:NOTE:
an additional option kit from Rack Solutions. The Rack Solutions brackets can be purchased at:
http://www.racksolutions.com/hp
Rack Adapter Kit
NOTE:
NOTE:
NOTE:NOTE:
The Third Party Rack Kit is required for round hole racks or for square hole racks that do not
Support for all 2-post Telco racks requires the Third Party Rack Kit (PN 274739-B21) kit plus
This kit allows HP rack servers to fit in racks that are 24" wide.
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
274739-B21
.
332815-B21
HP Rack 10000 Series
HP Rack 10000 Series
HP Rack 10000 SeriesHP Rack 10000 Series
(Graphite Metallic)
HP Rack S10614 (14U) Rack Cabinet– Shock Pallet
HP Rack 10842 (42U, 800mm wide) – Pallet
HP Rack 10842 (42U, 800mm wide) – Shock Pallet
HP Rack 10647 (47U) – Pallet
HP Rack 10647 (47U) – Crated
HP Rack 10642 (42U) – Pallet
HP Rack 10642 (42U) – Shock Pallet
HP Rack 10642 (42U) – Crated
HP Rack 10636 (36U) – Pallet
HP Rack 10636 (36U) – Shock Pallet
HP Rack 10636 (36U) – Crated
HP Rack 10622 (22U) – Pallet
HP Rack 10622 (22U) – Shock Pallet
HP Rack 10622 (22U) – Crated
HP Rack 10614 (14U) – Shock Pallet
NOTE:
NOTE:
NOTE: NOTE:
-B22 (shock pallet) used to ship racks with equipment installed (by custom systems, VARs and
Channels)
–B23 (crated) used for air shipments of empty racks
NOTE:
NOTE:
NOTE: NOTE:
HP equipment is qualified to be shipped in the Rack 10000 series
KVM USB Interface Adapter
Server Console Switch 1 x 4 port (100-230 VAC)
Server Console Switch, 0 x 1 x 8 port
Server Console Switch, 0 x 2 x 16 port
Server Console Switch 1 x 4 port (100-230 VAC) (Int’l)
Server Console Switch 1 x 4 port (100-230 VAC) (Japan)
IP Console Switch Box, 1 x 1 x 16
IP Console Switch Box, 3 x 1 x 16
IP Console Interface Adapter, 8 pack
IP Console Interface Adapter, 1 pack
IP Console Expansion Module
CPU to Server Console Cable, 12’
CPU to Server Console Cable, 3’
CPU to Server Console Cable, 7’
IP CAT5 Cable 3’, 4 pack
IP CAT5 Cable 6’, 8 pack
IP CAT5 Cable 12’, 8 pack
IP CAT5 Cable 20’, 4 pack
IP CAT5 Cable 40’, 1 pack
Switch Box Connector Kit (high voltage) (Int'l)
TFT5600 Rack Keyboard Monitor
Country Code Key
Country Code Key
Country Code Key Country Code Key
XX = 001
XX = 031
XX = 041
XX = 051
XX = 061
XX = 071
XX = 081
1U Rack Keyboard & Drawer (Carbon)
Country Code Key
Country Code Key
Country Code Key Country Code Key
XX = 001
XX = 031
XX = 041
XX = 051
XX = 061
XX = 071
XX = 081
Factory Installation, Racking, and Customization Services
Factory Installation, Racking, and Customization Services
Factory Installation, Racking, and Customization ServicesFactory Installation, Racking, and Customization Services
Factory Express Server Configuration Level 1
NOTE
NOTE
: Free Installation of HP Options - Installation of HP Options memory, NICs, hard drives,
NOTENOTE
controllers, processors, I/O cards, pre-install standard OEM OS image, and tape drives. Installation
fees will apply to all non-HP certified hardware and asset tags.
Factory Express Server Configuration Level 2
NOTE
NOTE
: Includes Level 1 Customer Intent of a ProLiant server and options configuration, OS
NOTENOTE
installation, custom image download, IP addressing, network setting, and custom packaging.
Customer unique requirements (quick restore creation, cd duplication, test reports, real-time reporting
of server MAC address, password, and RILOE). Customer access, validation and control through VPN
(price/server).
Factory Express Rack Integration Level 3 with 1 – 3 servers or storage enclosures
Factory Express Rack Integration Level 3 with 4 – 9 servers or storage enclosures
Factory Express Rack Integration Level 3 with 10 or more servers or storage enclosures
NOTE:
NOTE:
NOTE: NOTE:
standard cable mgmt, RAID configuration, servers & storage, power distribution, networking gear and
accessories (price/ra520ck).
Factory Express Rack Integration Level 4 with 1 – 3 servers or storage enclosures
Factory Express Rack Integration Level 4 with 4 – 9 servers or storage enclosures
Factory Express Rack Integration Level 4 with 10 or more servers or storage enclosures
NOTE:
NOTE:
NOTE: NOTE:
convention, customer furnished image download, IP addressing, cluster configurations (SQL, External
storage RAID). Quick restore creation, cd duplication, test reports, real-time reporting of server MAC
address, password, RILOE). Customer access and validation through VPN (price/rack).
Factory Express Rack Integration Level 5 with 1 – 3 servers or storage enclosures
Factory Express Rack Integration Level 5 with 4 – 9 servers or storage enclosures
Factory Express Rack Integration Level 5 with 10 or more servers or storage enclosures
NOTE
NOTE
NOTENOTE
access, validation and control through VPN, Clustered racks with networking gear and/or external
storage array, Start-up installation services custom quote. (price/rack).
NOTE:
NOTE:
NOTE: NOTE:
Express. Please contact a your local reseller or Account Manager.
Includes Level 1 Customer Intent for standard mounted servers and storage units plus
Includes Level 2 Customer Intent plus customer defined cable management and naming
: Includes Level 4 Customer Intent plus Custom SW layering and extended test, Customer
Factory Express Engineered Solution Level 6 is a custom solutions available through Factory
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
293355-888
266326-888
325736-888
232539-888
325735-888
325734-888
232540-888
325733-888
325732-888
232541-888
325731-888
Service and Support
Service and Support
Service and SupportService and Support
Offerings
Offerings
OfferingsOfferings
(HP Care Pack Services)
NOTE:
NOTE:
NOTE: NOTE:
Windows NT, Windows 2000 Server/Advanced Server or Novell NetWare Operating System.
Hardware Services On-site Service
Hardware Services On-site Service
Hardware Services On-site ServiceHardware Services On-site Service
4-Hour On-site Service 5-Day x 13-Hour Coverage, 3 Years
(Canadian Part Number)
4-Hour On-site Service, 5-Day x 13-Hour, 3 Years
(U.S. Part Number)
4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years
(AP/EMEA Part Numbers)
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years
(Canadian Part Number)
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years
(U.S. Part Number)
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years
(AP/EMEA Part Numbers)
Hardware Installation (Canadian Part Number)
Hardware Installation (U.S. Part Number)
Hardware Installation (AP/EMEA Part Number)
The Service and Support Offerings specifying Microsoft O/S in the description cover
DA - 11585 Worldwide — Version 33 — July 16, 2004
FP-HE3EC-36
331104-002
U4713A
U4713E
FP-HE7EC-36
401784-002
U4714A
U4714E
FP-HEINS-EC
401794-002
U4723A
U4723E
Page 24
QuickSpecs
Options
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
Installation & Start-Up of a ProLiant server and Microsoft O/S per the Customer Description and/or
Data Sheet. To be delivered on a scheduled basis 8am-5pm,
M-F, excl. HP holidays. (U.S. Part Number)
Installation & Start-Up of a ProLiant server and Microsoft O/S per the Customer Description and/or
Data Sheet. To be delivered on a scheduled basis 8am-5pm,
M-F, excl. HP holidays. (Canadian Part Number)
Installation & Start-Up of a ProLiant server and Microsoft or Linux O/S per the Customer Description
and/or Data Sheet. To be delivered on a scheduled basis
8am-5pm, M-F, excl. HP holidays. (AP/EMEA Part Numbers)
Installation & Start-Up of a ProLiant server and Linux O/S per the Customer Description and/or Data
Sheet. To be delivered on a scheduled basis 8am-5pm,
M-F, excl. HP holidays. (U.S. Part Number)
Installation & Start-Up of a ProLiant server and Linux O/S per the Customer Description and/or Data
Sheet. To be delivered on a scheduled basis 8am-5pm,
M-F, excl. HP holidays. (Canadian Part Number)
Support Plus
Support Plus
Support PlusSupport Plus
Onsite HW support, 8am-9pm, M-F, 4hr response and Microsoft O/S SW Tech support offsite, onsite
at HP's discretion, 8am-9pm, M-F 2hr response time excl. HP holidays. (U.S. Part Number)
Onsite HW support, 8am-9pm, M-F, 4hr response and Microsoft O/S SW Tech support offsite, onsite
at HP's discretion, 8am-9pm, M-F 2hr response time excl. HP holidays. (Canadian Part Number)
Onsite HW support, 8am-9pm, M-F, 4hr response and Microsoft O/S SW Tech support offsite, onsite
at HP's discretion, 8am-9pm, M-F 2hr response time excl. HP holidays. (AP/EMEA Part Numbers)
Onsite HW support, 8am-9pm, M-F, 4hr response and Linux O/S SW Tech support offsite, onsite at
HP's discretion, 8am-9pm, M-F 2hr response time excl. HP holidays. (U.S. Part Number)
Onsite HW support, 8am-9pm, M-F, 4hr response and Linux O/S SW Tech support offsite, onsite at
HP's discretion, 8am-9pm, M-F 2hr response time excl. HP holidays. (Canadian Part Number)
Onsite HW support, 8am-9pm, M-F, 4hr response and Linux O/S SW Tech support offsite, onsite at
HP's discretion, 8am-9pm, M-F 2hr response time excl. HP holidays (AP/EMEA Part Numbers)
Support Plus 24
Support Plus 24
Support Plus 24Support Plus 24
Onsite HW support 24x7, 4hr response and Microsoft O/S SW Tech support offsite, onsite at HP's
discretion, 24x7 2hr response time incl. HP holidays.
(U.S. Part Number)
Onsite HW support 24x7, 4hr response and Microsoft O/S SW Tech support offsite, onsite at HP's
discretion, 24x7 2hr response time incl. HP holidays.
(Canadian Part Number)
Onsite HW support 24x7, 4hr response and Microsoft O/S SW Tech support offsite, onsite at HP's
discretion, 24x7 2hr response time incl. HP holidays.
(AP/EMEA Part Numbers)
Onsite HW support 24x7, 4hr response and Linux O/S SW Tech support offsite, onsite at HP's
discretion, 24x7 2hr response time incl. HP holidays. (U.S. Part Number)
Onsite HW support 24x7, 4hr response and Linux O/S SW Tech support offsite, onsite at HP's
discretion, 24x7 2hr response time incl. HP holidays.
(Canadian Part Number)
Onsite HW support 24x7, 4hr response and Linux O/S SW Tech support offsite, onsite at HP's
discretion, 24x7 2hr response time incl. HP holidays.
(AP/EMEA Part Numbers)
HP Care Pack Priority Service Plan - Priority Silver
HP Care Pack Priority Service Plan - Priority Silver
HP Care Pack Priority Service Plan - Priority SilverHP Care Pack Priority Service Plan - Priority Silver
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Silver Software Support, 1-hr response,
Monday - Friday, 8AM - 5PM local time, 2-hr response after hours for Windows NT, Windows 2000,
Professional, Server or Advanced Server Operating System, Technical Account Manager, Technical
Newsletter, SW activity review, proactive patch notification, 1 System Healthcheck per year
(6-3 Part Number for U.S.)
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Silver Software Support, 1-hr response,
Monday - Friday, 8AM - 5PM local time, 2-hr response after hours for Windows NT, Windows 2000,
Professional, Server or Advanced Server Operating System, Technical Account Manager, Technical
Newsletter, SW activity review, proactive patch notification, 1 System Healthcheck per year
240016-002
FM-MSTEC-04
U4724A
U4724E
331110-002
FM-LSTEC-04
239937-002
FM-M01E4-36
U4725A
U4725E
331108-002
FM-L01E4-36
U4727A
U4727E
239939-002
FM-M02E4-36
U4726A
U4726E
331099-002
FM-L02E4-36
U4728A
U4728E
239941-002
FM-M04E4-36
DA - 11585 Worldwide — Version 33 — July 16, 2004
Page 25
QuickSpecs
Options
(2-5-2 Part Number for Canada)
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Silver Subsequent System Support for
Windows NT, Windows 2000, Professional, Server or Advanced Server Operating System (6-3 Part
Number for U.S.)
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Silver Subsequent System Support for
Windows NT, Windows 2000, Professional, Server or Advanced Server Operating System (2-5-2 Part
Number for Canada)
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Silver Software Support, 1-hr response,
Monday - Friday, 8AM - 5PM local time, 2-hr response after hours for Novell NetWare Operating
System, Technical Account Manager, Technical Newsletter, SW activity review (6-3 Part Number for
U.S.)
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Silver Software Support, 1-hr response,
Monday - Friday, 8AM - 5PM local time, 2-hr response after hours for Novell NetWare Operating
System, Technical Account Manager, Technical Newsletter, SW activity review (2-5-2 Part Number for
Canada)
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Silver Subsequent System Support for Novell
NetWare Operating System (6-3 Part Number for U.S.)
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Silver Subsequent System Support for Novell
NetWare Operating System (2-5-2 Part Number for Canada)
HP Care Pack Priority Service Plan - Priority Gold
HP Care Pack Priority Service Plan - Priority Gold
HP Care Pack Priority Service Plan - Priority GoldHP Care Pack Priority Service Plan - Priority Gold
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Gold Software Support, 30 minute response
(critical), 1-hr response (non-critical), for Windows NT, Windows 2000, Professional, Server or
Advanced Server Operating System, Technical Account Manager, Technical Newsletter, SW activity
review, proactive revision management, Upgrade impact planning, 2 System Healthcheck per year (63 Part Number for U.S.)
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Gold Software Support, 30 minute response
(critical), 1-hr response (non-critical), for Novell NetWare Operating System, Technical Account
Manager, Technical Newsletter, SW activity review, Upgrade impact planning (2-5-2 Part Number for
Canada)
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Gold Subsequent System Support for Novell
NetWare Operating System (6-3 Part Number for U.S.)
24 x 7 HW, 4-hr response, Named HW engineer; 24 x 7 Gold Subsequent System Support for Novell
NetWare Operating System (2-5-2 Part Number for Canada)
HP Care Pack Priority Service Plan - Priority Gold Executive
HP Care Pack Priority Service Plan - Priority Gold Executive
HP Care Pack Priority Service Plan - Priority Gold ExecutiveHP Care Pack Priority Service Plan - Priority Gold Executive
24 x 7 HW, 2-hr response, Named HW engineer; 24 x 7 Gold Software Support, 30 minute response
(critical), 1-hr response (non-critical), for Windows NT, Windows 2000, Professional, Server or
Advanced Server Operating System, Technical Account Manager, Technical Newsletter, SW activity
review, proactive revision management, Upgrade impact planning, 2 System Healthcheck per year (63 Part Number for U.S.)
24 x 7 HW, 2-hr response, Named HW engineer; 24 x 7 Gold Software Support, 30 minute response
(critical), 1-hr response (non-critical), for Windows NT, Windows 2000, Professional, Server or
Advanced Server Operating System, Technical Account Manager, Technical Newsletter, SW activity
review, proactive revision management, Upgrade impact planning, 2 System Healthcheck per year
(2-5-2 Part Number for Canada)
24 x 7 HW, 2-hr response, Named HW engineer; 24 x 7 Gold Subsequent System Support for
Windows NT, Windows 2000, Professional, Server or Advanced Server Operating System (6-3 Part
Number for U.S.)
24 x 7 HW, 2-hr response, Named HW engineer; 24 x 7 Gold Subsequent System Support for
Windows NT, Windows 2000, Professional, Server or Advanced Server Operating System (2-5-2 Part
Number for Canada)
24 x 7 HW, 2-hr response, Named HW engineer; 24 x 7 Gold Software Support, 30 minute response
(critical), 1-hr response (non-critical), for Novell NetWare Operating System, Technical Account
Manager, Technical Newsletter, SW activity review, Upgrade impact planning (6-3 Part Number for
U.S.)
24 x 7 HW, 2-hr response, Named HW engineer; 24 x 7 Gold Software Support, 30 minute response
(critical), 1-hr response (non-critical), for Novell NetWare Operating System, Technical Account
Manager, Technical Newsletter, SW activity review, Upgrade impact planning (2-5-2 Part Number for
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
239943-002
FM-M24E4-36
239981-002
FM-N04E4-36
239983-002
FM-N24E4-36
239945-002
FM-N08E4-36
239987-002
FM-N28E4-36
239949-002
FM-M09E4-36
239951-002
FM-M29E4-36
239989-002
FM-N09E4-36
DA - 11585 Worldwide — Version 33 — July 16, 2004
Page 26
QuickSpecs
Options
Canada)
24 x 7 HW, 2-hr response, Named HW engineer; 24 x 7 Gold Subsequent System Support for Novell
NetWare Operating System (6-3 Part Number for U.S.)
24 x 7 HW, 2-hr response, Named HW engineer; 24 x 7 Gold Subsequent System Support for Novell
NetWare Operating System (2-5-2 Part Number for Canada)
NOTE:
NOTE:
For more information, customer/resellers can contact
NOTE:NOTE:
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
http://www.hp.com/services/carepack
239991-002
FM-N29E4-36
DA - 11585 Worldwide — Version 33 — July 16, 2004
Page 27
QuickSpecs
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
Memory
HP ProLiant DL740 2.2GHz/2MB or 2.0GHz/1MB, 2048 MB (4P)
HP ProLiant DL740 2.2GHz/2MB or 2.0GHz/1MB, 2048 MB (4P)
HP ProLiant DL740 2.2GHz/2MB or 2.0GHz/1MB, 2048 MB (4P)HP ProLiant DL740 2.2GHz/2MB or 2.0GHz/1MB, 2048 MB (4P)
Standard Memory
Standard Memory
Standard MemoryStandard Memory
2048-MB addressable protected ECC SDRAM DIMM memory (2 x 256-MB DIMMs x 5 Hot-Plug RAID Memory Cartridges. The 5th cartridge is populated for
redundancy.)
Standard Memory Plus Optional Memory
Standard Memory Plus Optional Memory
Standard Memory Plus Optional MemoryStandard Memory Plus Optional Memory
Up to 51,200-MB of addressable ECC SDRAM DIMM memory is available with the installation of optional ECC SDRAM DIMM memory expansion kits.
Standard Memory Replaced with Optional Memory
Standard Memory Replaced with Optional Memory
Standard Memory Replaced with Optional MemoryStandard Memory Replaced with Optional Memory
Up to 65,536-MB of addressable ECC SDRAM DIMM memory is available with the removal of standard memory and the installation of optional ECC
SDRAM DIMM memory expansion kits.
NOTE:
NOTE:
NOTE: NOTE:
redundant mode) Hot-Plug RAID Memory Cartridges. Tables do not represent all possible configurations.
Cartridge 1
Cartridge 1
Cartridge 1Cartridge 1
(C1)
(C1)
(C1)(C1)
Cartridge 2
Cartridge 2
Cartridge 2Cartridge 2
(C2)
(C2)
(C2)(C2)
Cartridge 3
Cartridge 3
Cartridge 3Cartridge 3
(C3)
(C3)
(C3)(C3)
Cartridge 4
Cartridge 4
Cartridge 4Cartridge 4
(C4)
(C4)
(C4)(C4)
Cartridge 5
Cartridge 5
Cartridge 5Cartridge 5
(C5)
(C5)
(C5)(C5)
8 slots per Hot-Plug RAID Memory Cartridge. Memory must be added in banks of two DIMMs per cartridge across all five (four if running in a non-
HP ProLiant DL740 3.0 GHz/4MB, 2.7GHz/2MB, 2.8GHz/2MB or 2.5GHz/1MB 4096 MB (4P)
HP ProLiant DL740 3.0 GHz/4MB, 2.7GHz/2MB, 2.8GHz/2MB or 2.5GHz/1MB 4096 MB (4P)
HP ProLiant DL740 3.0 GHz/4MB, 2.7GHz/2MB, 2.8GHz/2MB or 2.5GHz/1MB 4096 MB (4P)HP ProLiant DL740 3.0 GHz/4MB, 2.7GHz/2MB, 2.8GHz/2MB or 2.5GHz/1MB 4096 MB (4P)
Standard Memory
Standard Memory
Standard MemoryStandard Memory
4096-MB addressable protected ECC SDRAM DIMM memory (2 x 512-MB DIMMs x 5 Hot-Plug Memory Cartridges. The 5th cartridge is populated for
redundancy.)
Standard Memory Plus Optional Memory
Standard Memory Plus Optional Memory
Standard Memory Plus Optional MemoryStandard Memory Plus Optional Memory
Up to 53,248MB of SDRAM DIMM memory is available with the installation of optional SDRAM DIMM memory expansion kits.
Standard Memory Replaced with Optional Memory
Standard Memory Replaced with Optional Memory
Standard Memory Replaced with Optional MemoryStandard Memory Replaced with Optional Memory
Up to 65,536-MB of SDRAM DIMM memory is available with the removal of standard memory and the installation of optional SDRAM DIMM memory
expansion kits.
NOTE:
NOTE:
NOTE: NOTE:
redundant mode) Hot-Plug RAID Memory Cartridges. Tables do not represent all possible configurations.
Cartridge 1
Cartridge 1
Cartridge 1Cartridge 1
(C1)
(C1)
(C1)(C1)
Cartridge 2
Cartridge 2
Cartridge 2Cartridge 2
(C2)
(C2)
(C2)(C2)
Cartridge 3
Cartridge 3
Cartridge 3Cartridge 3
(C3)
(C3)
(C3)(C3)
Cartridge 4
Cartridge 4
Cartridge 4Cartridge 4
(C4)
(C4)
(C4)(C4)
Cartridge 5
Cartridge 5
Cartridge 5Cartridge 5
(C5)
(C5)
(C5)(C5)
8 slots per Hot-Plug RAID Memory Cartridge. Memory must be added in banks of two DIMMs per cartridge across all five (four if running in a non-
7.00 x 17.5 x 28.7 in (17.78 x 44.45 x 72.90 cm)
105 lb (47.63 kg)
Rated Input Voltage
Rated Input Frequency
Input Power
Rated Input Current
1555 Watts [5309 BTU/hr]
(System is configured to draw
maximum power)
Use of 110 volt power sources is
)
not recommended.
Rated Steady-State Power
Maximum Peak Power
Operating
Non-operating
Shipping
Operating
Non-operating
101.7° F(38.7° C)
Idle
(Fixed Disk Drives Spinning)
L WAd (BELS)
L pAm (dBA)
115 to 120 VAC/200 to 240 VAC (lowline/highline)
47 to 63 Hz (lowline/highline)
1060W/1440W (lowline/highline)
10A at 115 VAC/8A at 200 VAC (lowline/highline)
Please refer to the Power Calculator at:
50° to 95° F at sea level, altitude de-rating of 1.8° F per
1,000 ft to 10,000 ft (10° to 35° C at sea level, altitude
de-rating of 1° C per 300 m to 3,000 m). Maximum rate
of change is 18° F/Hr (10° C/Hr)
-22° to 140 ° F ( -30° to 60° C). Maximum rate of change
is 36°F/Hr (20°C/Hr)
5% to 95% relative humidity, non-condensing
10 to 90% relative humidity, 82.4° F (28° C) maximum
wet bulb temperature, non-condensing
5 to 95% relative humidity, 101.7° F (38.7° C) maximum
wet bulb temperature, non-condensing
7.6
59
HP ProLiant DL740
HP ProLiant DL740
HP ProLiant DL740HP ProLiant DL740
.
DA - 11585 Worldwide — Version 33 — July 16, 2004
Page 33
QuickSpecs
Technical Specifications
Power Supply
Power Supply
Power SupplyPower Supply
1100/800W, Hot Plug
1100/800W, Hot Plug
1100/800W, Hot Plug1100/800W, Hot Plug
Redundant
Redundant
Redundant Redundant
Input Specifications
Input Specifications
Input SpecificationsInput Specifications
General Specifications
General Specifications
General SpecificationsGeneral Specifications
Ambient Temperature
Ambient Temperature
Ambient TemperatureAmbient Temperature
Range
Range
RangeRange
Dielectric Voltage
Dielectric Voltage
Dielectric VoltageDielectric Voltage
Withstand
Withstand
WithstandWithstand
Input Transient
Input Transient
Input TransientInput Transient
Susceptibility
Susceptibility
SusceptibilitySusceptibility
(2 standard)
One Redundant Power Supply
(optimized to provide full redundancy at 220 volts)
Normal Line Voltage
Range Input Line
Frequency Range
Power Factor
Input Current
Inrush Current
Holdup Time
Full Output Rating
Minimum Load
Operating
Non-operating
Input to Output
Input to Ground
Common and Differential
Mode (superimposed on AC
line)
115 to 127 VAC/200 to 240 VAC
115 to 132 VAC/180 to 265 VAC
47 to 63 Hz
0.95
10 A at 115 VAC/8 A at 200 VAC
100 A
21 ms from zero crossing at 120 VAC
To 104° F (40° C) and 5,000 ft (1524 m)
To 89.6° F (32° C) and 10,000 ft (3,048 m)
(derate linearly)
1 A on + 5 V output; 2 A on + 12 V output;
1 A on + 3.3 V output
41° to 109° F (5° to 43° C) (End use system maximum
ambient of 35°C, plus a maximum of 8° C due to rack
effect)
-40° to 185° F (-40° 85° C)
3,000 VAC/min
1,500 VAC/min
± 1kV line on AC power port for 1 minute;
320 MB/s total; 160 MB/s per channel
One external and one internal SCSI port
32 MB of DRAM used for code, transfer buffers, and non-battery-backed read cache
160 MB/s
32
Yes
RAID 5 (Distributed Data Guarding
RAID 1+0 (Striping and Mirroring)
RAID 1 (Mirroring)
RAID 0 (Stripping)
The information contained herein is subject to change without notice.
Microsoft and Windows NT are US registered trademarks of Microsoft Corporation. Intel is a US registered trademark of Intel Corporation.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein
should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
DA - 11585 Worldwide — Version 33 — July 16, 2004
Page 36
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.